Construction of Remaining work of New Jharkhand High Court Building at Dhurwa,Ranchi

Amount

Earth Work Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of cavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Hard rock (blasting prohibited)

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for PRE-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Extra for lead up to 1KM Beyond the initial lead of 50M as per specifition and direction of Engineering -in charges.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of Eli ( Mode of measurement compacted volume)

Concrete Work Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All works upto plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth.

RCC Work Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size) derived from natural sources.

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (Excluding landings) except spiral -staircases.

Extra for shuttering in circular work

Weather shade, Chajjas, corbels etc., including edges

Cornices and mouldings

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5 m for every additional height of 1 metre or part thereof (Plan area to be measured.) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured).

Providing Tor steel reinforcement of 8mm& 10 mm. dia . rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Providing Tor steel reinforcement of 12mm.& Above dia . rods as per approved design and drawing including cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position (excluding carriage of M.S. bars to work site) all complete as per building specification and direction of E/l. TMT Fe 500 (only vailid for Tata (tiscon), SAIL, JSPL, Electrosteel ltd Bokaro and Vizag(RINL))

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Extra for providing richer mixes at all floor levels. (Note:- Excess/ less cement over the specified cement content used is payable/ recoverable separately.) Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/ cum)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum.Excess/less cement used as per design mix is payable/recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Brick Work Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. bars at every third course of half brick masonry.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately).

Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in Charge.

Marble Work Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade

Area of slab over 0.5 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/ Granite/ stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick pre-polished granite stone in dado, skirting, risers of steps etc., on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with cement slurry @ 3.3 kg/sqm and pointing with white cement slurry ad-mixed with pigment of matching shade etc. all complete as per Architectural drawings and as per direction of the Engineer-in-Charge.

Wood Work Providing wood work in frames of false ceiling, partitions, paneling etc. sawn and fixed in position with necessary stainless steel screws etc.

Kiln seasoned and chemically treated hollock wood

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) :

Rectangular or square.

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing fire resistant door frame of section 50X60 mm on horizontal side & 35X60mm on vertical sides having built in rebate made out of 1.6mm thick GI sheet (Zinc coating not less than 120gm/sqm) suitable for mounting 120min Fire rated Glazed door shutters. The frame shall be filled with Mineral wool Insulation having density min 96 Kg/cum. The frame will have a provision of G.I Anchor fasteners 14 nos (5 each on vertical style & 4 on horizontal style os size M10x80) suitable for fixing in the opening along with factory made template for SS Ball bearing Hinges of size 100x89x3 mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or powder coating of not less 30 micron in desired shade as per the directions of Engineer - in charge.(cost of SS ball bearing hinges is excluded)

Providing and fixing 60mm thick glazed fire resistant door shutters of 120 min Fire rating confirming to IS:3614 (Part II) or EN16341:1999 , tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60mmx60mm wide and bottom rail of 110mmx60mm made out of 1.6mm thick G.I sheet(zinc coating not less than 120 gm/sqm) duly filled mineral wool insulation having density min 96 Kg/cum and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30micron etc all complete as per direction of Engineer-in -charge (paneling to be paid for separately)

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, making grooves, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

6mm thick commercial ply conforming to IS: 303 BWR grade

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings with rawl plugs screws etc.

Providing and fixing plain ceiling for all heights with necessary screws/ nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, making grooves, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

6mm thick commercial ply conforming to IS: 303 BWR grade

Steel Work Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Flooring Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

18mm thick

Providing and fixing glass strips in joints of terrazo/ cement concrete floors.

40 mm wide and 4 mm thick

Extra for pre finished nosing to treads of steps of marble/ granite stone.

Extra for Marble/ granite stone in treads of steps and risers using single length up to 2.0 metre .

Extra for pre finished nosing in treads of steps of Kota stone slab.

Extra for Kota stone in treads of steps and risers using single length up to 1.05 metre.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick.

Kota stone slabs 20mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1: 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood

Providing and laying Double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matching pigments etc., the tiles must be cut with zero chipping diamond cutter only. laying of tiles will be done with notch trowel, plier, wedge, clips of requred thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 1200x600 mm

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Roofing Making khurras 45x45 cm. with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) over PVC sheet1mx1mx400 micron, finished with12 mm cement plaster1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase metre

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Finishing Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming coat with cement primer

Painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coats.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing two coats of synthetic enamel paint of approved shade and make over Red lead Primer steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Extra for plastering done on moulding, cornices or architraves including neat finish to line and level:

In two coats

Melamine polishing on wood work (one or more coat).

Aluminium Work Providing and fixing aluminium work for doors, windows, ventilators, louvers and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket and filling side gap/cop with Silicon sealant etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion i/c door frames

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in- charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium/ upvc door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

UPto 5mm depth and 5mm width

Providing, assembling, supplying & fixing of vision glass panels (IGUs), in UPVC/ Aluminium windows, comprising of hermetically-sealed 6- 12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. For payment, only the actual area of glass on face # 1 of the glass panels shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size According to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm).

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete.

Water Proofing Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly Embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

b) Laying brick bats with mortar using broken bricks /brick bats 25 mm to 115 size with 50 % of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.7 kg/sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer -in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern fo 300 x 300 mm square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer -in- charge.

With average thickness of 120mm and minimum thickness at khurra as 65 mm.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C kitchen and the like consisting of :

Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1: 3 (1 cement :3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface

IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.)

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Dismantling & Demolishing Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Dismantling steel work in built up sections in angles, tees, flats and channels etc including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Carriage of material

Clay Brick

fly ash Brick

steel

Plumbing SANITARY INSTALLATIONS Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass toilet paper holder :

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirrors of 6mm thick plate glass bevelled edge mirror including C.P.brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600mm x 450mm size.

C.P. brass liquid soap container.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Providing and fixing 15mm size C.P. brass pillar cock (Weight not less than 350gms).C.I. body brass spindle pillar cock of approved quality as per specification and direction of Engineer-in Charge. C.P. body brass spindle.

WATER SUPPLY Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

Providing and fixing gun metal fully way valve of approved quality all complete as per specification and direction of etc.

20mm dia and weight not less then 400gms

25mm dia and weight not less then 500gms

32mm dia and weight not less then 700gms

40mm dia and weight not less then 1.0kg.

50mm dia and weight not less then 1.5kg.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm dia

SOIL, WASTE, VENT & RAIN WATER PIPES Providing and fixing on wall face unplasticised Rigid PVC rain water and waste pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm outer dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 110 mm

Single pushfit Coupler 110 mm

Single tee with door 110x110x110 mm

Single tee without door 110x110x110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

40 mm dia

32 mm dia

50 mm outer dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (F.T. + U.T.)

100 mm inlet and 100 mm outlet hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS : 15905

External plumbing Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All Kind of Soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 80x90 cm and 60cm deep including SFRC cover with frame (Medium duty) 800x900 mm internal dimensions.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cm

With common burnt clay F.P.S. (non modular) designation 7.5

Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement motar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement :3 coarse sand sand :6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design:

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for circular type manhole 0.91m internal dia (at bottom with beyond 0.91m to 1.67m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 1.22m internal dia at bottom and 0.56m dia at top in cement motar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement :3 coarse sand sand :6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 ( 1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design:

1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for circular type manhole 1.22m internal dia (at bottom with beyond 1.68m to 2.29m

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Constructing masonary chamber 90 cm X 90 cm X 100 cm inside with 75 class designation brick work in cement mortar 1: 4 ( 1 cement : 4 coarse sand ) for sluice valve with C. I. Surface Box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix(1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3(1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design.

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Constructing masonry Chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Garden hydrant valve, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Providing and fixing G.I. pipes complete with G.I. fittings including, trenching and refilling etc.

external works

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work.

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing CI sluice valve (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately)

100 mm dia (Class-II)

150 mm dia (Class-II)

200 mm dia (Class-II)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25mm nominal bore

40mm nominal bore

50mm nominal bore

80mm nominal bore

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450 x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm diameter

250 mm diameter

300 mm diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level.

200 mm dia.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer –in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

150 mm dia

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5

Circular shape 560 mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

All types of soil

200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conformingto IS: 12818, including hire & labour charges, fittings & accessories etc.all complete, for all depths, as per direction of Engineer-in-charge.

150 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

150 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

150 mm clamp

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

80 mm nominal bore Vertical

FIRE FIGHTING WORKS SUB HEAD - I (WET RISER SYSTEM - PUMPING EQUIPMENTS) Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required :

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

Suitable HP Squirrel cage induction motor, TEFC,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.

2850 lpm at 70 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump)

Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required.

M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.

2850 lpm at 70 m Head

SPRINKLER JOCKEY/HYDRANT FIRE PUMP Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following,complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation,conforming to IS : 325.

M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.

180 lpm at 70 m Head

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

1.2 Meter high and 250 mm dia.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.5

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

450 lpm at 35 m Head

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

200 mm dia

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

200 mm dia (6mm thick)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

150 mm dia

100 mm dia

65 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

150 mm dia

80 mm dia

100 mm dia

SUB HEAD - III - (HYDRANTS SYSTEM) Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Upright Sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150 mm dia

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Sluice Valve 200 mm dia. as per direction of E/C

ELECTRICAL WORKS SUB HEAD (I) :- INTERNAL WIRING Point wiring in PVC conduit, with modular type switch :- Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate,suitable GI box etc. as required.

Group A

Group C

Twin Control Point wiring in PVC conduit, with modular type switch :- Wiring for twin control light point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate,suitable GI box etc. as required.

Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- Wiring for power plug with 2 x 4 Sq.Mm. FR PVC insulated, copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 Sq.Mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub main wiring in PVC conduit :- Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire.

4 x 6 sq.mm. + 2 x 6 sq.mm. Earth wire.

4 x 10 sq.mm. + 2 x 10 sq.mm. Earth wire.

4 x 16 sq.mm. + 2 x 16 sq.mm. Earth wire.

S/F light plug point Modular type accessories :- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps. modular Type Switch, connection, painting etc. as required.

S/F power plug point modular type accessories :- Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required.

Supplying and fixing of following modular switch/ socket outlet on the existing Modular plate & switch including connection but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

Supplying and fixing following size/ modules, GI box Boxes alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (78mmX78mmX45mm)

4/5 Module (78mmX140mmX50mm)

6 Module (78mmX205mmX50mm)

8 /9Module (78mmX230mmX60mm)

12 Module (135mmX205mmX60mm)

Telephone Socket outlet

TV Antenna socket outlet

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular type electronic fan regulator :- Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

S/F Modular type Blanking Plate :- Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing hexagonal fan box circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

SUB HEAD (II) :- TELEPHONE, TELEVISION & DATA SYSTEM S/F PVC Conduit Supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required :

Supply and drawing following pair, 0.5 sq.mm. FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit as required.

Supply and drawing co-axial TV cable RG-6 grade copper conductor PE insulated,with PVC sheath in the existing surface / recessed PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

SUB HEAD (III) :- DISTRIBUTION BOARDS & MCB's S/F T.P MCB DB :- Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

6 way (4 + 18), Double door, Horizontal Type

8 way (4 + 24), Double door, Horizontal Type

S/F S.P MCB DB :- Supplying and fixing following way, single pole and neutral, sheet MCB distribution board 240 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

12 way Double door

S/F 4P MCB Isolator Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

64 Amps(Incomer for Vertical DB)

125 Amps (Incomer for Vertical DB)

40 Amps DP

S/F SPN (RCCB) Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

S/F 'C' Series MCB :- Supplying and fixing following 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

6/32 amps, Single Pole

50/63 Amps TPN (Outgoing for Vertical DB)

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

MAIN BDS S/F VERTICAL TYPE T.P MCB DB :- Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

8 way (4 + 24), Double door,Vertical Type

Providing and fixing M.V. danger notice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription single red colour on front side as required.

SUB HEAD IV):-INTERNAL LIGHTING FIXTURES & FANS SUPPLY OF LIGHTING FIXTURES Supply of Surface Mounting Round 12 Watt LED Down Lighter having Powder Coated die cast aluminium housing with heat sink,diffuser/reflector and driver set complete in all respect.

Supply of Recessed Mounting Round 15 Watt LED Down Lighter having Powder Coated die cast aluminium housing with heat sink,diffuser/reflector and driver set complete in all respect of Polycab Cat No COB LED DOWNLIGHT 15W ROUND 6500Kor equivalent

Supply of 36 Watt Recessed Mounting LED Square Ceiling Fitting Having Powder Coated die cast aluminium housing body with extended heat sink, diffuser of polycarbonate material and driver set complete in all respect of Polycab Cat No Multimounted 2X2 Backlite panel 36W, 5700K or equivalent

Supply of LED MIRROR LIGHT Complete Including tube etc on Wall complete in all respect .

Supply of LED BULK HEAD LIGHT Complete Including tube etc on Wall complete in all respect .

Supply of AC 230/250 volts, 50 HZ ceiling fan with standard down rod, blades, 2 nos. caps & regulator etc. ISI marked complete as required..

1400 mm sweep (fusion-50 5*)

1200 mm sweep (fusion-50 5*)

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete .

(Approved Make)

Exhaust Fan Heavy duty 230V A.C 50 cycles 375 mm 1400 RPM

ERRECTION OF LIGHTING FIXTURES Installation, testing and commissioning of pre-wired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

ITC Exhaust fan upto 450mm sweep:- Installaition of Exhaust Fan upto 450 mm, sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required

SUB-HEAD -V : EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 6 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm Copper. strip on surface or in recess for connections etc. as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

SUB HEAD(VI):- LT CABLE AND TERMINATIONS SUPPLY OF L.T. CABLE: Supplying of following sizes of 1.1 KV grade multicore aluminium conductor XLPE insulated armoured cable conforming to IS:1554 (Part - I) complete with all amendments etc. as required

3.5 C X 50 Sq.mm Al. XLPE arm.

3.5 C X 70 Sq.mm Al. XLPE arm.

LT CABLE LAYING LT CABLE JOINTING & END TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 50 sq. mm (38mm)

3½ X 70 sq. mm (38mm)

LT CABLE LAYING Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable 1.1 KV grade of following size in the existing rcc/hume/stoneware/metal pipe as required .

up to 35 sqmm

exceeding 95 sqmm to 185 sqmm.

exceeding 185 sqmm to 400 sqmm.

Supply and making end termination with brass double compression gland including providing and crimping of Aluminium solderless lugs / ferrules for XLPE armoured power Aluminium conductor cable 1.1 KV grade of following sizes:-

3.5 x 300 sq.mm

3.5 x 240 sq.mm

3.5 x 185 sq.mm

3.5 x 120 sq.mm

3.5 x 70 sq.mm

3.5 x 50 sq.mm

3.5 x 35 sq.mm

3.5 x 25 sq.mm

4 x 16 sq.mm

4 x 10 sq.mm

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100mm dia

250mm dia

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Add (or deduct) for using extra (or less) cement in the items Sl No 17 & 18 of design mix over and above the specified cement content therein.

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.

Powder coated minimum thickness 50 micron aluminium

Providing and fixing stainless steel (SS304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. Size 355 x 19 mm

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Powder coated minimum thickness 50 micron aluminium tubular handle bar

Non- Schedule items

Wood Work Providing and fixing aluminium die cast body TS 68 door closer with standard arm (EN2/3/4 max door width 1100mm necessary accessories and screws etc complete of approved make

Providing and fixing approved brand and manufacture SS 304 grade Mortice lock with key cylinder 60 mm fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt (TBS 310 S)250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt (TBS 36 S) 150mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type 25mm x 300 (PH2512) mm fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Supply & fixing of door closers of UL listed Heavy duty std arm with silver body finish and tested in accordance of EN 1634 - 3 and for mechanical test to EN 1154 for 50000 cycles and shall be tested with the fire doors for 2 hrs. fire rating from the CBRI Roorkee as per the directions of Engineer-in-charge

Supply & fixing of Fire rated SS D Type Pull Handle of size 300mm Long as per the directions of Engineer-in-charge.

Providing and fixing Approved', make Glass Reinforced Concrete (G.R.C) Screens casted with 'Spray Mix' concrete design in approved size, pattern, thickness of 50mm on the outer Border & 25-30mm for Internal member and shade. The Screens should be made from ‘53 grade’ White Portland Cement , White Quartz fine graded sieved Silica Sand, Alkali Resistant Glass Fibre , Owen Corning, Super Plasticizers, Polymers and U.V resistant Synthetic inorganic pigments should be used for pigmentation The Screens casting shall take place with layering methodology using- Direct Power Spray machines. The GRC Screens flexural strength average L.O.P should be above or equivalent to 6 N/mm2 & M.O.R should be above or equivalent to 15 N/mm2 for tests done on 28 days cured samples.

The fixing of Screens should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work, MS Framework. SS / MS Galvanized CLAMPS & PINS also if required fasteners to be used of Wurth, Hilti & Fischer or equivalent. All Cast in Socket to be Epoxy Primer Coated. Electrodes, Vendor shall submit shop drawings of same, the drawings to be duly approved from Engineer in charge at site

Providing, supplying and installing at site GRC Columns, Cornice or any othrt Decorative elements as per drawing detail made up of mainly White Cement, High Silica sand , AR Glasfibre, Admixtuers, hand cast or spray mix Cast Premix Process as per details provided in drawings and site requirements/ measurements and as per approved finish and color shade, with sealers and hardwares required, all in accordance with the manufacturer's specifications and conforming to Indian/ASTM standards, along with submission of shop drawings for approval, complete in all respects.

GRC Column Approved Design Inner Dia.600mm & above

GRC Column Approved Design Inner Dia.450mm

Flooring Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement guarantee. The carpet should have permanent static control & should be fixed with providing and fixing powder coated aluminum angles as per detail. The work should be carried out by the authorized installer of the Company in India. (Basic rate Rs. 234 per sqft)

Finishing Providing and fixng wall paper on walls for all floors & heights finished in smoth line and level etc. all complete (Basic rate Rs. 200 per sqft)

Providing & Fixing Aquaguard/Kent/Bluestar/Voltas Auto,RO,UV& TDS Controller Storage Water Cooler Cum Purifier Water Storage Capacity: 80 ltrs. , Three Mode of Operation (Auto, RO,UV & TDS Controller as Per Raw Water Quality) LCD Screen to Display TDS and Total Water Produced.) Two Faucets, Purification capacity 100 Litre/hour, alongwith 1 year annual maintainance contract (AMC) (Detail Technical Description as Per the given details ) With Accessories.

Providing & Fixing Kent Perk Auto,RO,UV& TDS Controller Storage Water Cooler Cum Purifier Water Storage Capacity: 20 ltrs. , Three mode of Operation (Auto, RO,UV & TDS Controller as Per Raw Water Quality), Purification capacity 50 Litre/hour, Two Faucets, alongwith 1 year annual maintainance contract (AMC) (Detail Technical Description as Per the given details ) With Accessories.

Providing & Fixing 20’’ Pre Filter (Compulsory item for High Iron & Turbidity Zone)

Expansion Joint Treatment Treatment of Expansion/Construction Joint after cleaning of existing concrete surface from loose dust-durt, repairing damaged edges and crack by moisture insensitive epoxy adhesive and high strength thixotropic epoxy based repair mortar, filling the existing gap with required dia of polystrene Baker Rod and seal the top surface with 2 mm thick flexible FPO based membrane (Elongation at Break, Fire Rating, Behaviour under hydrostatic pressure, Seam strength and Tear Strength as per IS/EN Standard) of Sika/Pidilite/Fosroc/BASF/other approved make as per manufacturer specification, guideline, approval & instruction of Engineer-in-Charge all tools, tackles, plant and labour complete.- Application width 60 mm to 100 mm Supplying and applying 2 mm thick aluminium plate 250 mm wide keeping one side fixed and other side screwed in oval slotted with washer to allow required movent in the joint as per satisfaction of EIC to provide protection layer of expansion joint strip. Providing and applying 20 mm x 12 mm flexible polysulphide sealant whereever required with suitable primer in between construction joint gap over poysterene / polyetheline backer rod in construction joint. The system to cover necessary surface preparation with all tools and tackles complete.

Floor to Floor/ floor to wall Joint of 100 mm

wall joint of 100 mm

roof to roof joint of 100 mm

Rebaring Providing and fixing chemical rebaring of following dia bars of required depth, all complete as per complete specifications

Plumbing SANITARY INSTALLATIONS Providing and fixing of CP brass Health faucet with 8mm dia 1mtr. Long PVC tube and wall hook fixed to wall with rawl plug and CP brass screws complete. (Approved Make)

Prividing and Fixing 1.5 feet long connecting hose with nuts at both ends complete.(Approved Make)

Supplying automatic 'NO-Touch ' SS electric hand-driers complete with all accessories & fittings.(Approved Make)

WATER SUPPLY Providing and fixing capacity of 25 ltr Geyser approved shape including providing & fixing capacity 3 litre/6 litre, including fittings, nuts, bolts and gasket etc complete.

Providing and fixing uPVC class-B(IS:13592) trap of self cleaning design complete including cost of cutting and making good the cut-outs in walls and floors etc. complete (P or S trap).

110 mm Outer dia inlet and 110 mm outer dia out let

Providing and fixing 100% stainless steel grating of approved make and quality grade 304 on top of floor trap & Floor drain. The rate includes the cost of all ancillary works and material as required to complete the works.(Approved Make)

127mm (Cat No.-SRG-SFCL-127)

Providing and fixing CLEANOUT PLUG for cleaning (Approved Make)

For 110 OD Pipe (Cat No.-CO-R-128)

Providing & fixing 75mm x 50mm uPVC waste with reducing elbow & nipple cutting chases, the floor / slab, repairs complete as required and connection to pvc waste pipe.

Providing and fixing uPVC HOPPER CONNECTION for 100 mm dia floor trap formed out of main pipe (Type A) with multiple side inlets, suitable for various dia pipes, side connections, including all fixtures and fittings as per site conditions and as per standard details and water tight sealing of joints and area surrounding the grating and as directed.

Supplying all materials, labour, T&P and fitting and fixing Hubless Cast Iron soil, waste, ventilating pipes and required fittings conforming to IS: 1729–2002 or its latest revision to walls with nails, bobbins and wooden plugs or laying in trenches including earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge. Including required shielded coupling for Hubless centrifugally cast iron pipe

Providing and fixing G.I. (class-C) pipes and fittings conforming to IS: 1239 clamps and hinges including cutting chases and holes and making good the walls and ceiling for waste pipes from wash basins, urinals kitchen sink and equipment waste connections pump deliveries & suction & condensate drainage as directed.

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

External plumbing Providing and laying DWC PIPE (SN8) Made from HDPE material, PE – 100 material as per IS 16098 (Part 2) including testing of joints etc. complete :

150 mm diameter

250 mm diameter

Providing and fixing HDPE pipes of PE 80 Grade stabilized including all HDPE as per IS:4984 electrofusion fittings i/c support at 1.0mm c/c & testing of joints complete as per direction of Engineer in Charge

PN - 8 Pipe, 63 mm OD PE80

PN - 8 Pipe, 110 mm OD PE80

PN - 8 Pipe, 160 mm OD PE80

Domestic Water Pump (Hydropneumatic System With Variable Speed Pumps)

Providing, fixing and testing of factory fitted packaged variables frequency drive type skid mounted hydropneumatic system with variable speed system comprising of :-

Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel SS-316L shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.

Pressure vessel of non corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000 cycles.

No. and capacity of Pressure Vessel – 01 Nos. x 150 Ltrs

Control Panel with programmable logic controller (PLC) for cyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs should confirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan.

Pressure switches bellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standards and IP55 protection class.

SS Suction and delivery header with Ball valves Hot Pressed brass OT-58 with stainless steel ball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall follow following duty.

Domestic Water Pumps(Set of Ttree Pumps Two Working + One Standby)

Capacity : app. 300 lpm

Head : app. 35 m

Flushing Water Pumps(Set of Three Pumps Two Working + One Standby)

Capacity : app. 300 lpm

Head : app. 35 m

Providing, fixing and testing of skid mounted pumping system comprising of :-

Horizontal, Single Stage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel SS-316L shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.

Control Panel with programmable logic controller (PLC) for cyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs should confirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan, controlloer for start and stop of pumps in case of high level and low level in treated water tank, cables, earth wire & control cables.

SS Suction and delivery header with Ball valves Hot Pressed brass OT-58 with stainless steel ball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall follow following duty.

Filter/Softener Feed Pump

No. of Pumps: 3 (2 Working + 1 Stand by )

Capacity : app.300 lpm

Head : 35m

Pressure Filter (Domestic Water) Providing and fixing vertical pressure filter with dual media filter (comprising of 600mm bed depth of graded sand gravel and 600mm bed depth of Anthracite) fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2)

Discharge : 18000 lph

Filtration Rate : 20000 lit./m2/h

Suggested dia app. : 1.10 m

Activated carbon Filter (Domestic Water)

Providing and fixing vertical activated carbon filter comprising of activated carbon filter media fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2)

Discharge : 18000 lph

Filtration Rate : 20000 lit./m2/h

Suggested dia app. : 1.10 m

Water Softener Providing and fixing ‘Cation’ ION exchange water softener fabricated from minimum 8mm thick M.S. plate on shell and 10mm thick M.S. plate on dished ends complete with initial charge of filter media and ION exchange resins, face piping accessories, piping testing and commissioning complete with resins of approved quality and make and brine tank of required capacity. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration).

Minimum expected rate of flow: 18000 lph

Total soft water to be produced between two regeneration: app. 150 Cu.m

Expected raw water hardness : app. 500 ppm

Expected treated water hardness: less than 100 ppm

Max. working pressure : 4 Kg/cm2

Total soft water to be produced between two regeneration: app. 150 Cu.m

Providing and fixing M.S salt saturator, internally rubber lined as per requirement and externally painted with suitable anti-corrosive paint, with all required accessories for holding and supplying salt for softener complete in all respects, with electrically operated stirrer and of capacity 1000 litres.

Panel shall be supplied with P&I based online MIMIC display with LED's at all specific drive /operation to enable Visual Display of Complete pumps activity on Panel front.

For domestic water hydro pumps, raw water pump, auto chemical doser and sump pumps etc. in plant room.

One incoming main isolation 200A TPN MCCB (35ka).

250 A TPN Fully taped aluminum bus bar in a separate bus bar chamber.

100A TPN MCCB outgoing for Hydro-pneumatic system.-2 Nos

100 A TPN MCCB outgoing for Softener/filter feed pumps

6 Nos. 40 A TP MCB of for each sump pumps

Neon phases indicating lights on the incoming mains.

All internal wiring colour coded from incoming mains to various switchgear, starter, meter, indicating lamp and bus bar. All the cable entry to the panel shall be from the top.

(All for above from item (a) to (i) complete set). (The shop drawing to be prepared and approved before fabrication)

Providing and fixing motor pump controller cum water level indicating panel in powder coated sheet metal box in 16 gauges M.S including the following:

Electronic water level controller working on magnetic type sensing probes with necessary length of armored cable up to control panel.

Electronic minimum 4-level indicator with magnetic type sensing probes and necessary length of armored cable upto control panel.

Arrangement of alternate switching mechanism for operational and standby pumps.

For Water level indicators with following details:

Underground tanks

Minimum 4 level Multi level indicators with magnetic type sensor probes complete.

For water level controllers with electronic sensing probe complete in all respect for following functions.

i) Tubewell Water Pumps

To cut off at low level in raw water U.G tanks. And cut off at high level in U.G Domestic and soft water tank.

Providing and fixing G.I. pipes (I.S. 1239 heavy duty class) complete with all necessary G.I. Fittings including all necessary fittings like bends, elbows, tees etc., either welded or screwed or flanged joints as per requirements, including all anchor blocks, anchor fasteners, couplings in all respects including enamel painting of required shade, cutting holes and chases in RCC wall and making good complete (The cost of flanges will be paid separately).

100mm dia

150mm dia

Providing and fixing C.I double flanges suction strainer bucket type/ “Y” type including, nuts, bolts and 3mm thick rubber insertion complete.

100mm dia

150mm dia

Providing and fixing butterfly valves, wafer end type class PN 1.0 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box)

100mm dia nominal bore.

150mm dia nominal bore.

Supply, installation, testing and commissioning of the compact brass ball valve with motorised actuator complete with float switch to acuate the motorised valve, contactor with control panel, 3 phase, 415C AC supply complete in all respects.

a. 32mm dia

b. 40mm dia

c. 50mm dia

Providing and fixing M.S. slotted cable tray supported from ceiling at intervals of 60cms on both ends including cable clips with nuts and bolts welding of support rods with ceiling inserts or through dash fasteners cutting and making good complete.

300mm wide

150mm wide

Providing and fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size, drilling, welding fixing and welding to insert plates in RCC structural members or through dash fasteners as per site conditions as directed by Engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.)

Submersible pumps Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect

(one working+One Standby)

(Solid handiling capacity 12mm)

Capacity- 225 lpm (Each)

Head - 12 m

HP (Approx) 1.0 HP

Supplying & installation of Lubi make submersible pump set directly coupled with 7.5 HP motor nominal speed 2900 RPM suitable for operation on 3-phase, 50 cycles, 400 + 5% volts A.C. power supply to give yield of 30000/24000 LPH at a head of 50/70 mtrs.

Total head = 50/70 Mt

Flow rate = 36000/30000 LPH

H P = Minimum 7.5 HP

(Or as per site condition)

Supply, installation and commissioning of panel board duly wired made of 16/18 SWG sheet including fixing of the same in wall/floor on angle iron frame as per site conditions, and fitted with the following:

1 No. L & T make DOL starter.

1 No A/E make suitable range voltmeter size 96 mm.

1 No A/E make suitable range ammeter size 96 mm.

1 No. minilec make single phase preventer.

3 Nos MCB for lamps, ammeter and voltmeter.

3 Nos. indicating lamps (Approved Make).

1 No MCB of suitable range (Approved Make).

Push button ON/ OFF switch L & T make - 1 No.

Supply & installation of 80 mm dia column pipe made out of 80 mm dia GI including the cost of fittings complete in all respect Approved Make 'B' class pipe.

Providing & fixing heavy duty PVC sheathed copper conductor 1100 volts grade cables with clamps complete in all respect.

Control cable for low water level guard 2 core 2.5 Sq.mm.

Power cable 3 core 4 Sq.mm.

SEWAGE TREATMENT PLANT ( 450KLD)

Design, supplying, installing, testing & commissioning of Sewage Treatment Plant 450 KLD electro mechanical system based on MBBR technology. (excluding all Civil & construction work)

BOD5 250-400 mg/lt

COD 600-800 mg/lt.

SS 200-450 mg/lt.

Oil & Grease upto 50 mg/lt

Desired Sewage discharge standard after treatment are as below: (after ultra filteration)

BOD5 : upto 30 mg/l

COD : upto 100 mg/l

S. Solids : upto 10 mg/l

Ammonical Nitrogen : upto 5 mg/l

Total Nitrogen : upto 10 mg/l

Oil & Grease : Nil

Fecal Coliform (MPN/100ml) : < 230

Phosphate (PO4-P) : upto 2 mg/l

Bar Screen cum Oil & Grease Chamber 1No

Sewage equalization tank/sump- 1No.

MBBR Tanks- 4No.

Tube Settler Tank -2No.

Clean Water Tank -1No.

Sludge Holding Tank- 2No.

Flushing Water Tank -1No.

Irrigation Water Tank -1No.

(Owners scope shall include civil construction for RCC tanks, waterproofing & testing, manholes (covers & frames), PVC coated rungs, Vents, CI gratings for drain channel, hand railing, ladders, staircases, supply & fixing of puddle flanges, doors, grills & ventilators, lighting & ventilation, external finishing, foundation of equipments.)

Note: STP contactor has to provide necessary details regarding the above said works. All the structural work shall be subject to the approval of structural consultant.

Supply, installation, testing & commissioning of 2 Nos, 1200mm x 1000mm Stainless Steel Perforated, Coarse Type, corrugated Screen with 3mm thick SS 304 Sheet , with suitable garbage lifting arrangement. The sheet shall be hold by 3" x 1.5" Square pipe SS 304, 3mm thick.

Supply, installation, testing & commissioning of level indicators and controllers for automatic operation of the complete system with high/low level alarm complete with auxillary NO/NC contacts. (Required in equalization tank, clear tank, sludge holding tank, Flushing Water tank & Irrigation Water Tank).

Supply, Installation, testing & commissioning of Submersible, non clogging type pumps capable of handling solids upto 35 - 50mm having CI casing & CI impeller complete with mechanical seal & all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock. Pumps shall have following duty.

Raw Sewage Transfer Pumps

Flow Rate (each) = 12 m3 / hr (1W+1S)

Head = 12-15 Mtr

Supply, installation, testing & commissioning of Plant room sump pump with CI body & CI impeller pump . Plant Room sump pumps of centrifugal submersible type suitable for 415 + 10% voltage variation or 230 + 10% volts 50Hz AC supply. The pump shall be suitable for handling 10 to 12 mm solids.

Flow Rate (each) = 12 m3 / hr (1W+1S)

Head = 12-15 Mtr

Air diffusion system shall include the following:

Supply , installation, testing & commissioning of twin lobe, rotary Air blower capable of delivering 240 cum/hr t 0.5 kg/cm2 of free air at required pressure driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply.

Air Blowers (2W+1S)

Flow Rate (each) = 240 m3 / hr

Approved Make

Air piping shall comprise of SS 304 all submerged piping and MS 'C' class pipes in plant room complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, paint,supports & clamps, puddle flanges etc cutting chases & making good the wall wherever required. Contactor to submit detailed P & I indicating their proposal. Air Velocity shall not exceed 6m/s.

Supply Non-clog type air dispersion system capable of handling required 5-7 cfm of air with oxygen transfer efficiency. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. (Coarse bubble membrane diffusers)

Approved Make

Air dispersion system shall be provided for MBBR Tank, Equalization Tank,and Sludge Holding Tank.

Providing and fixing all interconnecting piping (as described below) and isolation control valves for making the system complete. The piping material shall be MS 'C' class.

All piping submerged in sewage waste/pumping sewage waste. SS 304

All piping for treatment plant & post treatment plant shall also be in.MS 'C' class.

Supply, installation, testing & commissioning of Chlorine dosing system with dosing solution and a 200 ltrs HDPE tank with 0-6 lph dosing pump.

Supply, installation, testing & commissioning of PP MBBR biodeck media. the media shall be enough for proper functioning of STP. Surface Area -400sqm/cum[MBBR System to be in two reactors. Approved Make

Supply, installation, testing & commissioning of PVC tube deck settling media to be installed in Tube Settler Tank . Approved Make

Supplying, installing, testing & commissioning of centrifugal filter feed pumps, CI body, CI impeller. motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply.

Filter feed pumps:

Capacity : 30 Cum/hr. (1W+1S)

Head : 35 Mtrs

Supply, Installation, testing and commissioning of Vertical Multigrade Sand Filter fabricated from bobbin wound polyester fiberglass multi-layer tank etc. complete including frontal piping and intially charge with media like pebbles, gravels, sand etc. Filter media shall be included in cost and shall include standard fittings like pressure gauges on inlet and outlet, sampling cocks, air vent , bolts, nuts and rubber gasket etc. complete.

Capacity - 30 M3 / Hr

Filtration rate - 18M³/M²/hr

Height of shell - 1.8 mtrs

Max. operating pressure - 3.5kg/sq.cm.

Test pressure - 5.5kg/sq.cm.

Shell Thickness - 6mm

Dished ends Thickness - 8mm

dia of filter - 1.8 mtrs.

Out Put Suspended solids : less than 5ppm

Multi grade Sand Media (minimum) -4200kg

Supply, installation, testing and commissioning of Vertical Activated Carbon Filter fabricated from bobbin wound polyester fiberglass multi-layer tank etc. complete including frontal piping and intially charge with activated carbon media. Filter media shall be included in cost and shall include standard fittings like pressure gauges on inlet and outlet, sampling cocks,,air vent , bolts, nuts and rubber gasket etc. complete.

Capacity - 30 M3 / Hr

Filtration rate -15 M³/M²/hr

Height of shell - 1.8 mtrs

Max. operating pressure - 3.5kg/sq.cm.

Test pressure - 5.5kg/sq.cm.

Shell Thickness - 6mm

Dished ends Thickness - 8mm

dia of filter - 1.8 mtrs.

Activated Carbon Media (minimum) - 1200 kg

Iodine Number : minimum 800 mg/g

Apparent Density : 2750kg/m3

Supplying, installing, testing & commissioning of centrifugal filter water transfer pumps for irrigation, CI body, CI impeller. motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply.

Irrigation Pumps (2 Nos: 1W+ 1S)

Capacity : 15.0 Cum/hr. (1W+1S)

Head : 35 mtrs.

FLUSHING WATER TRANSFER PUMP (HYDROPNEAUMATIC SYSTEM) Supply, Installation, testing and commissioning of factory fabricated Variable drive package type skid mounted hydropneumatic system comprising of:

Vertical inline single/multistage centrifugal pumping set with stainless steel SS stage casing and SS impellers with stainless steel shaft, cast iron suction & discharge casing, connected to suitable capacity TEFC ventilated induction motor 2 pole, 2900rpm, suitable for 415+10% Volts, 3 phase, 50 Hz A.C. supply.

Pressure vessel of non corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000 cycles.

No. and capacity of Pressure Vessel - 1 No. of suitable dia.

Electrical Control Panel including provision for cyclic operation of pumps - Pump working sequence should change after every operation. Control panel with programmable logic controller (PLC) with inbuilt PID controller , digital display with fluorescent screen, one no. 3 ph, 415 ± 10%V, , overload relays and MCBs should conform to IEC 898-1995 standards Ammeter, voltmeter. All trip indications should blink in case of trip and panels should only be accessible through an access code.

Electronic Pressure switches having maximum pressure and differential scale should confirming BS-6134 standards and IP55 protection class.

Complete set system to be mounted on a common MS base frame and shall follow following duty.

The cost will include making necessary flanged suction and delivery headers in GI (C class) and butter fly valves and Non return valves,rubber bellow on suction and delivery.

Motor to be of the same make as the pump

(Vendor to submit performance curves and technical catalog of the proposed model for review & information)

Flow Rate (each) = 10 m3 / hr (1W+1S)

Head = 70 Mtr

Supply, installation, testing & commissioning of filter press of Suitable Capacity 36" x 36" x 36" plates with MS frame, PP plates with filter cloth interconnecting piping and poly dosing system complete. Hydroloic Operation

SLUDGE RECIRCULATION PUMP :

Providing, fixing, testing & commissioning of horizontal centrifugal Sludge recirculation pumps. The pumps shall have CI casing, bronze Impeller & SS shaft & sleeve with mechanical rotary shaft seal connected by a flexible tier type coupling to TEFC induction motor mounted on a common channel base- plate with coupling guard, 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for including all necessary piping, valves and other accessories complete as required.

Capacity 4 m3/hr @ 10-12 m head (1W+1S)

Solid Handling capacity: 7-10 mm

Supply, installation, testing & commissioning of positive displacement type screw slurry pump with MS casing, SS-strator with internal rubber lining, gland packing seal, solid handling capacity upto 7 to 10% of the effective percentage of sludge and direct drive with motor.

Capacity : 3-5 m3/hr (1W+1S)

Head : 40 mtrs. (1W+ 1S)

Supply, installation, testing & commissioning of Electromegnatic type Flow Meter having acrylic body coupled with MS Flanges, of suitable capacity for 24 m3/h plant for 100mm dia line minimum.

Supply, installation, testing & commissioning of D.O. Meter of suitable capacity for 450 KLD plant.

Supply, installation, testing & commissioning of Ozonator (2 Set) to treat 20000-23000 lph water by each ozonator suitable for waste water application. The system should be complete consisting of Ozone Generator, Oxygen Generator, Air Compressor, Water Chilling System, Ozone Diffusers, Pipeline & fittings, Central Control Panel etc with Re-circulation based Ozone mixing system comprising of Re-circulation Pump, Ventury Injector, Static Mixer etc complete in all respect. (Approved Make)

Capacity = 100 grms / hr

(Note:- At present, STP contractor shall quote/supply 1 nos. Ozonator as per 1st phase of installation. Balance 1 No. of Ozonator shall be supplied at the time of future expansion of plant.)

Design, fabrication, assembling, wiring, supply of Electric control Panel shall be fabricated with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be provided in case of large panels. All second phase equipment's electrical equipment feeders for ultrafilteration outgoing supply shall be kept in the panel.

Supplying , installation, testing & commissioning of Cables and termination GI Cable Trays, to make Electrical Installation Complete.

Contractor shall include all electrical and mechanical items as required to operate the system automatically and also include in his rates any other components/tanks/ equipment/ etc. required to complete the job as required. Only main power supply with the earthing to be STP main control panel shall be provided by the owner through other agencies.

Bypass arrangement shall be provided such that equalization tank pump can be used to pump out sewage to external manhole incase of maintenance of STP.

ULTRA FILTRATION PLANT - CAPACITY 200 KLD Design, supplying, installing, testing & commissioning of UF Plant of capacity 10 m3/hr (excluding excavation, back filling & disposal of surplus earth /Civil construction work) for the following duty:

Nature of UF Feed Water - STP Treated Water

Average flow - 10 m3/hr

BOD5 - 30Mg/L

S. Solids - 50 Mg/L

COD - 450 – 100 Mg/L

Oil & Grease - 5 Mg / L

Supplying of Horizontal centrifugal Water Pumps, CI Casing, & Impeller along with motor, NRV on delivery line. Isolation valve, Mechanical seal, sdrain pipe with valve for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply.

Ultra-filtration Feed Pumps

Capacity : 24 m3/hr

Head :20-25M

No. of Pumps (1W+1S )

Ultra-filtration Back wash Pumps

Capacity : 12 m3/hr

Head :20-25 M

No. of Pumps (1W+1S )

Supplying, installing, testing & commissioning of Micron Cartridge Filter Unit with PP Housing

Size : 5 micron

Capacity : 10 m3/hr

Supplying, installing, testing & commissioning of Ultrafiltration Unit with SS Skid Membrane are made from a PVDF material with Excellent low Fouling Characterstics.

Capacity : 24 m3/hr

Membrane Type : Hollow Fiber

Nominal Membrane Pore Size : 0.02micron

No. of Membrane : as per requirement

Skid : 1no. SS304

Supplying, installing, testing & commissioning of Chemical Cleaning System with pipeing and Tank.

Capacity Tank : 200 Ltr

Capacity Tank : 100 Ltr

Providing and fixing all piping (as described below) and isolation control valves for making the system complete.

UPVC : Interconnecting pipe line after delivery header of pump/ Membrane

Supplying, installing, testing & commissioning of motorised operated butterfly Valve for automatic Operation MOC : Brass

Supplying, installing, testing & commissioning of Rota Meter.

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of PLC based motor control centre shall be fabricated with reinforcement of suitable size angle iron, channel ‘T’ sections irons and/or flats wherever necessary. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of red oxide primer and final approved shade of powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system.

Running option : Auto & Manual Both

Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation.

Furniture Chair Providing and supplying high back chair. The seat and back shall be made of double layered moulded (15+6)mm thick hot pressed commercial plywood upholstered with high resilience polyurethane foam (40+30)mm thick having density 40kg/m³ in seat and (30+25)mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support as well as head support. The armrest shall be used MS chrome plated arm with PU completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 660 mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard testecd to perform 98,000 cycles with 250lbs load.The seat size shall be 500±10 mm (D) X 480±10 mm (W) and back size shall be 520±10 mm (W) X700 ±10 mm (H) from seat. Overall height shall be = 1160±10 mm, overall width/depth = 760±10 mm. Geeken Model No.GP 162 Size Swivel Tilt

Providing and supplying mid back chair. The seat and back shall be made of double layered moulded (15+6)mm thick hot pressed commercial plywood upholstered with high resilience polyurethane foam (40+30)mm thick having density 40kg/m³ in seat and (30+25)mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. The armrest shall be used MS chrome plated arm with PU completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged MS/CRCA chrome plated having pitch circle Dia. 660 mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard testecd to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm (D) X 500±10 mm (W) and back size shall be 500±10 mm (W) X560 ±10 mm (Ht) from seat. Overall height shall be = 1025±10 mm, overall depth/width = 760±10 mm. Geeken Model No.GP 163 Size Swivel Tilt

Supplying and placing ergonomically designed, comfortable & aesthetically appealing High back chair. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine as well as head support. Moulded PP arm shall be used with cushion and leatherite upholstery. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle Dia. 660 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 515±10mm(W) X 490±10mm(D) and back size shall be 510±10 (W) X 650±10mm(H) from seat & overall height = 1110±10mm. Geeken Model No.GM 224A Size Swivel Tilt

Supplying and placing ergonomically designed, comfortable & aesthetically appealing Mid back chair. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ and 25mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine. Moulded PP arm shall be used with cushion and leatherite upholstery. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suite them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged made up of injection moulded in 30% glass filled black nylon having pitch circle Dia. 660 mm fitted with 5 nos. twin wheel castors, the castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 515±10mm(W) X 490±10mm(D) and back size shall be 510±10 (W) X 510±10mm(H) from seat & overall height = 945±10mm. Geeken Model No.GM 225A Size Swivel Tilt

Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polypropylene arm completely joint with seat. For seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 640mm and fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycle with 250lbs load. The seat size shall be 465±10 mm(W) X 460±10 mm(D) and back size shall be 480±10 mm(W) X 625±10 mm(H) from seat & overall height = 1060±10 mm. Geeken Model No.GB 415 Size Synchro Tilt

Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polypropylene arm completely joint with seat. For seating durability the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 120mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 640mm and fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycle with 250lbs load. The seat size shall be 465±10 mm(W) X 460±10 mm(D) and back size shall be 480±10 mm(W) X 520±10 mm(H) from seat & overall height = 960±10 mm. Geeken Model No.GB 416 Size Synchro Tilt

Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine and the armrest shall be used polypropylene arm completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 650 mm fitted with 5 nos. twin wheel castor. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 475±10 mm(W) X 490±10 mm(D) and back size shall be 450±10 mm(W) X 530±10 mm(H) from seat. Overall height shall be = 885±10 mm, base width/ depth = 710±10 mm. Geeken Model No.GA 538A Size Swivel Tilt

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40Kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. A chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal shall have five legged CRCA chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W) X 520±10 mm(D) and back size shall be 450±10 mm(W) X 535±10 mm(H) from seat & overall height = 980±10 mm, overall width = 560±10 mm & overall depth = 670±10 mm. Geeken Model No.GS 340 Size Swivel Tilt

Providing and supplying a visitor chair with ergonomic design for user comfort & shall have aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The seat and back shall be upholstered with leatherite tapestry 0.8±0.1mm thick, 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be supplied by keeping the natural curvature of the spine which helps to provide back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. Chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. The frame structure shall be cantilever support type made of MS CRCA chrome plated round pipe of dia. 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 500±10 mm(W) X 510±10 mm(D) and back size shall be 450±10 mm(W) X 540±10 mm(H) from seat & overall height = 980±10 mm, overall width = 560±10 mm. Geeken Model No.GS 341 Size Chrome Plated

Providing and supplying a visitor chair with ergonomic design for user comfort & aesthetically appealing. The seat and back shall be made of hot pressed commercial plywood 15mm thick and 12mm thick padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The chair shall be supplied with cushion arm with leatherite covering top mounted on metal frame. The frame structure shall be supported by four legs made up of MS CRCA powder coated 50-60µ thick tubular pipe of size 40mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 490±10 mm(D) X 560±10 mm(W) and back size shall be 530±10 mm(W) X 420±10 mm(H) from seat. Overall height shall be = 860±10 mm, overall depth = 690±10 mm & overall width = 620±10 mm. Geeken Model No.GP 140 Size

Supplying & Placing cafe chair. The complete structure shall be made up of 20% glass filled injection moulded polypropylene. The frame structure shall be supported by four legs made up of polypropylene having Dia. 35mm at upper and 25mm at lower i.e taper shape. The seat size shall be 410±10 mm(D) X 400±10 mm(W) and back size shall be 390±10 mm(W) X 420±10 mm(H) from seat. Overall height shall be = 845±10 mm, overall depth = 510±10 mm. Geeken Model No.GC 987 Size Stackable

Providing and supplying visitor chair with ergonomically designed. The seat and back shall be made up of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 40mm thick having density 40kg/m³ in seat and 25mm thick having density 32kg/m³ in back. The same shall be upholstered with fabric tapestry 0.6mm thick and 235 GSM. The seat and back shall be arrested together with metal frame and the armrest shall be used wooden arm mounted on chrome plated pipe frame completely joint with seat and back. The frame structure shall be cantilever supported type made up of MS/CRCA chrome plated round pipe of Dia 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 425±10 mm(D) X 430±10 mm(W) and back size shall be 430±10 mm(W) X 450±10 mm(H) from seat. Overall height shall be = 885±10 mm, overall depth = 600±10 mm & overall width = 540±10 mm. Geeken Model No.GV 603 Size Chrome Plated

Providing and supplying 3 seater visitor chair with 2 arms. The seat and back shall be made up of reinforced PU foam with MS perforated sheet. The seat mounted on MS powder coated rectangular cross beam having cross-section area 60mm X 60mm with 2mm thick fitted with polypropylene end caps on both side. The arm and leg shall be made up of pressure diecast aluminium. there shall be leveller shoe provided at the bottom with metal insert. The individual seat size shall be 515±10 mm(W) X 467±10 mm(D), Back size shall be 515±10 mm(W) X 510mm±10 mm(H) from seat, Overall depth shall be 680±10 mm, overall width shall be 1640mm±10 mm and overall height shall be 860±10 mm. Geeken Model No.Fly 2 Size

Providing and supplying 4 seater visitor chair with 5 arms. The seat and back shall be made up of reinforced PU foam with MS perforated sheet. The seat mounted on MS powder coated rectangular cross beam having cross-section area 60mm X 60mm with 2mm thick fitted with polypropylene end caps on both side. The arm and leg shall be made up of pressure diecast aluminium. There shall be leveller shoe provided at the bottom with metal insert. The individual seat size shall be 515±10 mm(W) X 467±10 mm(D), Back size shall be 515±10 mm(W) X 510mm±10 mm(H) from seat, Overall depth shall be 680±10 mm, overall wifth shall be 2180±10 mm and overall height shall be 860±10 mm. Geeken Model No.Fly 4 Size

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of double layered moulded natural wood and combination of (15+6) mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (30+25+19) mm thick having density (32 & 23) kg/m³ and the back shall be made of double layered moulded hot pressed plywood (12+6) mm thick padded with high resilience polyurethane foam (30+25) mm thick having density 32kg/m³. The seat and back shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as contoured lumbar support. The chair shall be supplied with cushion arm having teak wood base frame and leatherite covering top. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged made of CRCA chrome plated with cushion and leatherite covering top having pitch circle dia. 700mm and fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 515±10 mm(W) and back size shall be 615±10 mm(W) X 785±10 mm(H) from seat. Overall height shall be = 1250±10 mm, overall depth = 740±10 mm & overall width = 760±10 mm. Geeken Model No.Royal 1 Size Synchro Knee Tilt

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be of chrome plated frame padded with cushion with leatherite covering on top. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated pipe having cross section 40mm x 20mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 500±10 mm(W) X 500±10 mm(D) and back size shall be 490±10 mm(W) X 550±10 mm(H) from seat & overall height = 960±10 mm, overall width = 600±10 mm & overall depth = 670±10 mm. Geeken Model No.Civic 3 Size Chrome Plated

Providing and supplying visitor chair with ergonomic design for user comfort & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (30+25)mm thick having density (40 & 32)kg/m³ and the back shall be made of (15+6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick having density 32kg/m³. The same shall be upholstered with leatherite tapestry 1mm thick GKN 15. The backrest shall be made by keeping the natural curvature of the spine for back support. The chair shall be supplied with cushion arm with leatherite covering top and seat and back shall be arrested together with powder coated HR steel spine. The frame structure shall be cantilever support type made of MS CRCA chrome plated capsule pipe of size 40mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 450±10 mm(W) and back size shall be 560±10 mm(W) X 520±10 mm(H) from seat. Overall height shall be = 990±10 mm, overall depth = 660±10 mm & overall width = 680±10 mm. Geeken Model No.Eleganza 6 Size Chrome Plated

Providing and supplying high back chair with ergonomic design, user comfort and aesthetically appealing. The seat and back shall be made up of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. The chair shall be supplied with cushion arm with leatherite covering. It should be flap with soft cushion on both side for aesthetically appealing as well as side comfort. For seating durability the chair shall have Torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 65mm with BIFMA standard class-3 chrome plated gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged die cast aluminium duly chrome finish having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(W) X 470±10 mm(D) and back size shall be 585±10 mm(W) X 685±10 mm(H) from seat. Overall height shall be 1160±10 mm, overall depth = 700±10 mm & overall width = 730±10 mm. Geeken Model No.Karizma 1 Size

Providing and supplying medium back chair with ergonomic design, user comfort and aesthetically appealing. The seat and back shall be made up of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GMS. The backrest of the chair shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The chair shall be supplied with cushion arm with leatherite covering. It should be flap with soft cushion on both side for aesthetically appealing as well as side comfort. For seating durability the chair shall have Torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating user can adjust seat height up to 65mm with BIFMA standard class-3 chrome plated gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged die cast aluminium duly chrome finish having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standard X5.1-2011 tested to perform 98,000 cycles with 250lbs load.. The seat size shall be 500±10 mm(W) X 470±10 mm(D) and back size shall be 585±10 mm(W) X 685±10 mm(H) from seat. Overall height shall be 1160±10 mm, overall depth = 700±10 mm & overall width = 730±10 mm. Geeken Model No.Karizma 2 Size

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of natural wood and combination of (18+6)mm thick double layered moulded commercial plywood padded with high resilience polyurethane foam 70mm thick having density 40kg/m³ in seat and 70mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. The chair shall be supplied with polypropylene chrome cushion arm with leatherite covering top pivot joint with back. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged injection moulded polypropylene with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 530±10 mm(W) and back size shall be 500±10 mm(W) X 720±10 mm(H) from seat. Overall height shall be = 1180±10 mm, overall depth = 670±10 mm & overall width = 710±10 mm. Geeken Model No.GP 153 Size Torsion Bar

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of natural wood and combination of (18+6)mm thick double layered moulded commercial plywood padded with high resilience polyurethane foam 70mm thick having density 40kg/m³ in seat and 70mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The chair shall be supplied with polypropylene chrome cushion arm with leatherite covering top pivot joint with back. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged injection moulded polypropylene with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 530±10 mm(W) and back size shall be 500±10 mm(W) X 520±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 670±10 mm & overall width = 710±10 mm. Geeken Model No.GP 154 Size Torsion Bar

Providing and supplying lounge chair. The seat back assembly shall be made up of high resilience moulded polyurethane foam having density 45Kg/m³ with metal or bar insert. It should be upholstered with fabric tapestry 0.8mm thick and 235GSM. The understructure shall consist of solid round bar having dia. 12.7mm. It should be chrome plated. There shall be co-polymer polypropylene shoe provided at the bottom. Seat size shall be 450±10 mm(W) X 440±10 mm(D), back size shall be 420±10 mm(W) X 380±10 mm(H). Overall height shall be 710±10 mm, Overall width = 640±10 mm. Geeken Model No.GC 9057 Size

Supplying & Placing Cafe Chair. The seat shall be made of 12mm thick plyboard and SS metal frame upholstered with high resilience polyurethane foam 16mm thick having density 60kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of stainless steel shiny chrome finish frame. The frame structure shall be supportd by four legs made up of SS chrome finish pipe of size 30mmX10mm with 1.5mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 435±10 mm(D) X 440±10 mm(W) and back size shall be 325±10 mm(W) X 610±10 mm(H) from seat. Overall height shall be = 1080±10 mm. Geeken Model No.GC 9005 Size

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (50+25)mm thick having density 40kg/m³ and the back shall be made of (15+6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 40mm thick having density 32kg/m³. The seat and back shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. The chair shall be supplied with Chrome plated with cushion arm having leatherite top completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 530±10 mm(W) and back size shall be 540±10 mm(W) X 750±10 mm(H) from seat. Overall height shall be = 1210±10 mm, overall depth = 630±10 mm & overall width = 650±10 mm. Geeken Model No.Orion 1 Size Synchro Knee Tilt

Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (50+25)mm thick having density 40kg/m³ and the back shall be made of (15+6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 40mm thick having density 32kg/m³. The seat and back shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The chair shall be supplied with Chrome plated with cushion arm having leatherite covering top completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 530±10 mm(W) and back size shall be 525±10 mm(W) X 580±10 mm(H) from seat. Overall height shall be = 1040±10 mm, overall depth = 620±10 mm & overall width = 620±10 mm. Geeken Model No.Orion 2 Size Synchro Knee Tilt

TABLE Supplying & Placing Modular table in completely knock down conditions with an overall size 2250mm X 2180mm X 750mm that is to be assembled at site. The worktop shall be 43 mm thick having the combination of 18mm particle board as top and 25mm medium density fibre-board as base top. The top shall have the size 2000mm X 980mm with approved laminate and shade as well as deco paint. The profile shall be in rectangle shape with round front and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding and base top shall be in half round post forming with grooves. The top shall be supported on 75mm Peg mounted over side storage unit at one end and fixed pedestal unit at another end. The table shall be clad with 9mm thick modesty panel which provide structural support for the table having round profile in middle section and linear on both left and right with appropriate PVC edge banding connected with both end on side unit and fixed drawer with 25mm round spacer. The table shall have side unit for storage purpose with an overall size 1800mm X 500mm X 640mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 drawer and 1 shutter. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The side storage unit shall be mounted on 75mm Peg. A pedestal shall be provided with an overall size 500mm X 750mm X 640mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick, top 25mm and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on 75mm Peg. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007 certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Exclusive 5 Size 2250x2180

Supplying & Placing executive table with credenza and pedestal unit in completely knock down conditions with an overall size 1950mm X 1750mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1950mm X 850mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form edges and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Credenza unit shall be supplied for storage purpose with an overall size 900mm X 450mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc.

It shall have 2 nos. of shutter operated with the assistance of sliding rail track and SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 6 Size 1950x1750

Supplying & Placing Conference table in completely knock down conditions with an overall size 2400mm X 1200mm X 750mm that is to be assembled at site. The table top shall have same size made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. Single sided flapper box shall be enclosed at table top that houses video, audio, data and power connection discretely. The end wall of the table on the side shall be topped by gable end.

The gable end shall have the size 900mm X 570mm. The gable end shall be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall have the size 1750mm X 400mm with 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. The table shall be supported on SS pipe leg 202 grade. It shall have an overall size 800mm X 715mm with cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 10 Size 2400x1200

Supplying & Placing Modular table in completely knock down conditions with an overall size 1650mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The work top shall have the size 1650mm X 750mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall be supplied with side unit for storage purpose with an overall size 900mm X 450mm X 750mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated with the assistance of SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel having to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 6 Size 1650x1650x750

Supplying & Placing conference table in completely knock down conditions with an overall size 9000mm X 3000mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The connecting top shall be made up of 25mm thick Medium density fibre-board with deco painted. The table top profile shall be in rectangle shape with round corners with full round post forming edges at front and back and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on particle board base gable end and metal pole leg. The end wall of the table on the side shall be topped by gable end. It should be 25mm thick Pre-laminated particle board and profile shall be in linear shape with front and back full round post form edges and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Customised Size 9000x3000

Supplying & Placing modular table in completely knock down conditions with an overall size 3600mm X 1200mm X 750mm that is to be assembled at site. The table top shall be made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. The table shall be supported over SS pipe leg of 202 grade. It shall have cross-section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 10 Size 3600x1200

Supplying & Placing table in completely knock down conditions with an overall size 1800mm X 800mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with round front and back and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The table shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end.It should be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with full round post form and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 6 Size 1800x800

Supplying & Placing table in completely knock down conditions with an overall size 1500mm X 750mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with round front and back and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The table shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end.It should be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with full round post form and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Customised Size 1500x750

Supplying & Placing cafeteria table with an overall size 1200mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60µ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor. Geeken Model No.Customised Size 1200x900

Supplying & placing center table with an overall size 900mm X 600mm X 450mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The understructure shall consist of SS 202 grade pipe frame with shiny chrome finish having cross-section area 40mm X 20mm. There shall be PPCP shoe provided at the bottom to avoid scratches on the floor. Geeken Model No.Libra Centre Table Size 900x600

Supplying & placing corner table with an overall size 600mm X 600mm X 450mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823. The profile shall be in square shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The understructure shall consist of SS 202 grade pipe frame with shiny chrome finish having cross-section area 40mm X 20mm. There shall be PPCP shoe provided at the bottom to avoid scratches on the floor. Geeken Model No.Cliff Corner Table Size 450x450

Supplying & Placing office table in completely knock down conditions with an overall size 3000mm X 1200mm X 750mm that is to be assembled at site. The worktop shall be made up of Medium Density Fibre-board with approved veneer laminate. The top panel shall be in rectangle shape with 79mm thick (75mm MDF + 4mm Natural veneer & PU). Veneered portion of work surface shall be finish with PU polish. The edges of the table shall be supplied with solid brass bar strips having cross-section area 25mm X 5mm all around worktop. The top panel shall be supported on MS/CRCA rectangle pipe frame having cross-section area 40mm X 20mm with 1.6mm thick. The table top shall be enclosed with flapper box on both sides for electric provision duly polished. The end wall of the table on the side shall be topped by gable end. It should be 63mm thick made up of (59mm MDF + 4mm natural veneer & PU). The table shall be clad with 29mm thick (25mm MDF + 4mm natural veneer & PU) modesty panel which provide structural support for the table. The profile of the gable end and modesty panel shall be in linear shape with appropriate veneer surface. There shall be leveler provided with metal insert at the base to avoid scratches on the floor as well as uneven surfacing. The table shall be supplied with both side pedestal unit with an overall size 600mm X 920mm X 590mm. Top, side, back, facia shall be made up of 18mm thick MDF board with approved veneer laminate. It shall have 3 nos. of drawer operated with the assistance of soft closed ball bearing channel and grooves handle for easy griping. The complete structure shall be supplied with approved veneer laminate and PU polish accordingly. The table and pedestal have to be made in such a way that no gap should be seen in between. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. Geeken Model No.Manhattan 1 Size 3000x1200x750

Providing and supplying conference table in completely knock down conditions with an overall size 2400mm X 1200mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick Medium Density Fibre-board with approved veneer laminate. The top shall be supplied with thin layer of polyurethane polish and duly biffed for shining finish. The table top profile shall be in rectangle shape with round corners and full round post forming edges. Single sided Flip-up box shall be enclosed at table top that houses telephone cable, data and power connection discretely. The top shall be supported on gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick medium density fibre-board with deco painted and profile shall be in moulded construction shape with full round post forming edges. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. Geeken Model No.Accent 2 Size 8 Seater

Executive Table for Judges ( Court Dias)

Executive Table for Advocates (5 Seater)

1 Seater Geeken Model No. Size

2 Seater Geeken Model No. Size

Supplying & Placing Conference table in completely knock down conditions with an overall size Dia. 900mm X 750mm that is to be assembled at site. The table top shall have the size 900mm Dia. made up of 36mm thick MDF board with approved laminate and finish as per approved shade. The table top profile shall be in circular shape. The table shall be supported over MDF board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 36mm thick MDF board and profile shall be in linear shape and sealed with appropriate PVC edge banding. There shall be buffers provided at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 9 Size Dia 900mm MDF

Providing and supplying conference table in completely knock down conditions with an overall size 8796mm X 3553mm X 750mm that is to be assembled at site. The worktop shall be made up of 50mm thick Medium Density Fibre-board with approved veneer laminate. The top shall be supplied with thin layer of polyurethane polish and duly biffed for shining finish. The table top profile shall be in oval shape with round corners and full round post forming edges. Flip-up box shall be enclosed at table top that houses telephone cable, data and power connection discretely. The top shall be supported on gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 36mm thick medium density fibre-board with deco painted. The table shall be clad with 18mm thick full height modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in curve shape.Table shall have 100mm tick inner modesty. The raceway or metal wire carrier shall be situated below the worktop as per requirement of inlaying the electrical management and carrying the wire horizontally. There shall be buffers provided at the base to avoid scratches on the floor. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. Geeken Model No.Customised Conference Table Size 36 Seater

Supplying & Placing conference table in completely knock down conditions with an overall size 6000mm X 3000mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The connecting top shall be made up of 25mm thick Medium density fibre-board with deco painted. The table top profile shall be in rectangle shape with round corners with full round post forming edges at front and back and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on particle board base gable end and metal pole leg. The end wall of the table on the side shall be topped by gable end. It should be 25mm thick Pre-laminated particle board and profile profile shall be in linear shape with front and back full round post form edges and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Coonference 4 Size

Providing and supplying centre table with an overall size 1200mm x 600mm made up of 25mm thick Medium Density Fibreboard with approved veneer laminate and PU polished accordingly. It should be supplied with gable end in moulded structure with approved deco painted. It should be clad with modesty panel with approved laminate to provide structural support for the table. Geeken Model No.Walter Centre Table Size

Providing and supplying corner table with an overall size 600mm x 600mm made up of 25mm thick Medium Density Fibreboard with approved veneer laminate and PU polished accordingly. It should be supplied with gable end in moulded structure with approved deco painted. It should be clad with modesty panel with approved laminate to provide structural support for the table. Geeken Model No.Walter Corner Table Size

Supplying & Placing Modular table in completely knock down conditions with an overall size 1500mm X 750mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 7 Size 1500x750

Supplying & Placing Modular table in completely knock down conditions with an overall size 1800mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 1800mm X 750mm made up of 25mm thick particle board with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 900mm X 450mm X 750mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated with SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted over 65mm injection moulded nylon castor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 6 Size 1800x1650x750

Supplying & Placing Reception table in completely knock down conditions with an overall size 2400mm X 820mm X 1000mm that is to be assembled at site. The top shall have the size 2300mm X 695mm made up of 49mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The upper top shall have the size 1400mm X 300mm with 49mm thick. The top profile shall be in rectangle shape with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The side edges shall be covered with die casted aluminium profile. The table top and upper top shall be supported on particle board base strip. The table shall have a front panel having size 1390mm X 750mm with 49mm thick Pre-laminated particle board. A wire manager cap shall be provided on the top of the table for power connection. The end wall of the table on the side shall be topped by gable end. It shall be made up of 49mm thick Pre-laminated particle board and profile shall be in linear shape with one clipped corner and covered by Aluminium profile. There shall be buffers provided to avoid the scratches on the floor. The table shall be clad with 49mm thick modesty panel which provide structural support for the table. It should be 49mm thick pre-laminated particle board in linear shape with appropriate PVC edge banding and covered by aluminum profile connected with both end. The manufacturer shall have basic quality and safety certifications like ISO-9001:2015, ISO-14001: 2015, ISO-18001:2007, BIFMA Membership & AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Reception 1 Size 2400x820x1000

Supplying & Placing reception table in completely knock down conditions with an overall size 1500mm X 600mm X 1000mm that is to be assembled at site. The construction shall be free standing structure constructed with the help of minifix dowels and pins. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table shall have upper top shelf with 18mm thick Pre-laminated particle board. The main top shall be supported on MS powder coated pipe frame cross-section area 40mm X 20mm. The upper top shall be supported on 200mm metal studs. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The end wall of the table on the side shall be topped by gable end. It shall be made up of 18mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. There shall be buffers provided at the bottom to avoid the scratches on the floor. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board in linear shape with appropriate edge banding connecting both end. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 735mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. The pedestal shall have 1 drawer and 1 shutter. The drawer shall be operated on MP lock mechanism and SS handle and easily close & open with the assistance of sliding channel to enable smooth movement. The pedestal shall be mounted on injection moulded nylon castor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Reception 3 Size 1500x600x1000

Overall Approx Dimension: 1830mm L x 560mm W x 810mm H. Two section top with fix mattress. Backrest movement on Rachet. Pretreated and Powder Coated. Geeken Model No.GK 7007 Size 1830x560x810

Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted on nylon castors. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 7 Size 1200x600

Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted on nylon castors. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 7 Size 900x600 (Customised Size)

Supplying & placing executive table in completely knock down conditions with an overall size 1800mm X 750mm X 750mm that is to be assembled at site. The worktop shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board. The trey shall be operated on keyboard channel. The table shall be clad with modesty panel which provide structural support for the table. It should be 1mm thick CRCA star perforated sheet connected with both end. The table understructure shall consist of C frame MS/CRCA leg having cross-sectional area 60mm X 30mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with Al die cast handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on injection moulded nylon castor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 3 Size 1800x750 (Customised Size)

Supplying & Placing cafeteria table with an overall size 2100mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60µ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor. Geeken Model No.GC 9032 Size 2100x900 (Ciustomised Size)

Supplying & Placing Modular table in completely knock down conditions with an overall size 2700mm X 2300mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 2700mm X 1100mm/950mm X 750mm made up of 75mm thick Medium density fibre-board of general purpose of IS 12406 with Red veneer polished as per approved decorative colour. The table top profile shall have round structure with taper edges. The table top shall be supported on MDF base gable end. The end wall of the table on the side shall be topped by gable end. The 75mm thick Gable end shall be provided at both side with an overall size 820mm X 670mm of MDF with red veneer polished. The gable end shall be inclined as per table top constructed and edges shall have taper structure. The gable end base shall be made up of MDF with black polished having the size 840mm X 95mm with 10mm thick. The table shall be clad with 12mm thick modesty panel. The modesty panel shall be made up of Medium Density Fibre-board with an overall size 2290mm X 670mm. Modesty panel shall have round profile according to table top structure and shall be polished with leather, It shall have an outer modesty panel for aesthetically design made up of MDF polished with red veneer having the size 1600mm X 370mm with 12mm thick. The edges shall be taper as per approved design. A leather base 6mm thick writing pad shall be provided with an overall size 1100mm/900mm X 400mm. The side storage unit shall be provided with the top size of 1200mm X 600mm X 750mm made up of MDF board with red veneer. Storage top and skirting shall be 25mm thick, shutter, facia, adjustment shelf and divider shall be 18mm thick and bottom shall be 9mm thick made up of MDF board of IS 12406. Storage have 4 nos. drawers having size 735mm X 190mm & 735mm X 105mm shall be operated with the assistance of 400mm soft-close telescopic channel runs on ball bearing telescopic channel having load capacity 35kg, 1 nos. shelf having size 395mm X 530mm shall be adjustable type. All drawers shall have simultaneous locking property with the assistance of central locking mechanism and having leather base handle. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom with size 1160mm X 50mm and 520mm X 50mm with 25mm thick and black polished. Pedestal shall be provided with an overall size 600mm X 600mm X 650mm. The drawer top and side shall be 25mm thick, bottom, back and side panels including the drawer facia is made up of 18mm thick and drawer base shall be 9mm thick made up of MDF board of IS 12406. The top edges shall be taper structure. The drawer boxes shall be operated by 400mm bottom channel sliding roller to smooth operation having load carrying capacity 20 Kg. The drawer shall have centralize locking mechanism and leather base handle. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. Geeken Model No.Tiara Size 2700x2300x750

Supplying & Placing Modular table in completely knock down conditions with an overall size 2100mm X 1800mm X 750mm that is to be assembled at site. The top shall have the size 1900mm X 900mm made up of 45mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on 75mm Peg mounted over side storage unit and fixed pedestal. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 45mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. The table shall have side unit for storage purpose with an overall size 1800mm X 510mm X 625mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top and side 45mm thick and drawer base 9mm thick & other parts 18mm thick like shutter, back, facia, etc. It shall have 3 drawer and 2 sliding shutter. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A hanging pedestal shall be provided with an overall size 455mm X 685mm X 485mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick & drawer base shall be 9mm thick. The pedestal shall have 2 nos. of drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of sliding channels to enable operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Exclusive 7 With Side Unit Size 2100x1800x750

Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size 1950mm X 1800mm X 750mm that is to be assembled at site. The worktop shall have the size 1950mm X 900mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. Side top shall be provided with an overall size 800mm X 500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 1400mm X 575mm X 500mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Classic 9 Size 1950x1800x750

Supplying & Placing Conference table in completely knock down conditions with an overall size 2700mm X 900mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall have the size 2700mm X 900mm made up of 2 nos. 25mm thick Pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape with round front and back and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edgebander machine at 200 0C. The table shall be supported by particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall have the size 600mm X 715mm. The gable end shall be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with full round post form and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall have an overall size 1050mm X 600mm with 18mm thick Pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturershall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 6 Size 2700x900x750

Supplying & Placing Conference table in completely knock down conditions with an overall size Dia. 1200mm X 750mm that is to be assembled at site. The table top shall have the size 1200mm Dia. made up of 36mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 36mm thick Pre-laminated particle board and profile shall be in linear shape and sealed with appropriate PVC edge banding. There shall be buffers provided at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Conference 9 Size 1200mm Dia

Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 18mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with one side post forming edge and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 18mm thick particle board and profile shall be in linear shape. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. One hanging drawer shall be provided with an overall size 400mm X 450mm X 150mm with key locking mechanism. The drawer shall be made up of Pre-laminated particle board of grade II of IS 12823. Drawer side, back, facia shall be 18mm thick and drawer base shall be 9mm thick. The drawer shall be operated with Al die cast handle and easily close & open with the assistance of ball bearing channel to enable smooth operation. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Numero 9 Size 1200x600

WORKSTATION Supplying & Placing workstation table in completely knock down conditions with an overall size 1560mm X 1560mm X 1200mm that is to be assembled at site. The worktop shall have the size 1500mm/600mm X 1500mm/600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in curvilinear shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on particle board base gable end. The end wall of the top shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) provided at front of the user. Laminated bottom tile shall be situated below the work top. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on injection moulded nylon castor. A nylon castor based CPU unit shall be provided with an overall size 470mm X 286mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Max 7 Size

Providing and placing workstation table in completely knock down conditions with an overall size 1320mm X 660mm X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40µ-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways & 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X 284mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Max 1 Size 1320x660

Providing and placing workstation table in completely knock down conditions with an overall size 1200mm X 660mm X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40µ-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on corners. The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed on the partition for table top support. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be situated at bottom. Adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. Fixed type pedestal shall be provided with an overall size 400mm X 450mm X 725mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with Al Die cast handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A nylon castor based CPU unit shall be provided with an overall size 468mm X 284mm with 18mm thick Pre-laminated particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380. Geeken Model No.Max 1 Size Without Side Partitions

Sofa Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 202 grade pipe frame leg with shiny chrome finish having cross-section area 40mm X 20mm with 1.6mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 530±10 mm(D) X 1530±10 mm(W), seat height = 430±10 mm, overall width = 1800±10 mm, overall depth = 705±10 mm & overall height = 775±10 mm. Geeken Model No.Vegas 3 Size 3 Seater

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 202 grade shiny chrome finish pipe having cross-section area 40mm X 20mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 530±10 mm(D) X 1020±10 mm(W), seat height = 430±10 mm, overall width = 1300±10 mm, overall depth = 720±10 mm & overall height = 790±10 mm. Geeken Model No.Vegas 2 Size 2 Seater

Providing and supplying three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have SS 202 grade with shiny chrome finish frame having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 670±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 1270±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm. Geeken Model No.Regal 1 Size

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 571 GSM. The understructure shall consist of SS 304 grade leg with shiny chrome finish having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 1330±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 1930±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm. Geeken Model No.Regal 2 Size

Supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 304 grade leg with shiny chrome finish having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 2000±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 2600±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm. Geeken Model No.Regal 3 Size

Supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 1460±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 2030±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. Geeken Model No.Sirena 3 Size

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The armrest shall be flap with soft cushion on both side for aesthetically appealing as well as side comfort. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have MS powder coated frame having thickness 8mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 980±10 mm(W) X 530±10 mm (D) X 380±10 mm (H). Overall width = 1525±10 mm, overall depth = 830±10 mm & overall height = 860±10 mm. Geeken Model No.Sirena 2 Size

STORAGES Supplying & placing storage unit with an overall size 1800mm X 450mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top of the shutter shall be 25mm thick and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. The sliding shutter shall be operated on sliding rail track and SS handle as well as push lock mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380. Geeken Model No.Storage 8 Size

Supplying & placing storage unit with an overall size 900mm X 450mm X 1200mm. The storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top shall be made up of 25mm thick and other parts like side, back, shutter, facia, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall be supplied with 2 nos. of shelves. Door shutters shall be provided for opening and closing the storage. The shutter shall be operated with concealed crank hinge and die cast handle as well as proper locking arrangement. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380. Geeken Model No.Storage 11 Size

Providing, supplying and placing steel Almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The cabinet shall be supplied with 2 nos. of doors and 4 nos. of adjustable shelves. The doors shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the Almirah. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick. Geeken Model No.GMS 10 Size

Providing, supplying and placing lateral filing cabinet. The overall size of the cabinet shall be 900mm (W) X 450mm (D) X 1325mm (H). The cabinet shall be supplied with 4 nos. of drawer. The drawer shall be operated with aesthetically appealing snap fit ABS plastic handle and ball bearing base telescopic channel. All drawers shall be synchronized locked with central locking mechanism by one single key. Uniformly distributed load capacity of each drawer shall be 15/20 Kg. The entire body panel, shelf shall be made of prime quality 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the cabinet. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 50-60µ thick. Geeken Model No.GMS 7 Size

Providing and supplying metal book case with an overall size 915 mm (W) X 320 mm (D) X 1750mm (H). The book case shall be supplied with 4 nos. of individual compartments. Top, back & side panels shall be made of 0.8mm and rest 1mm high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Each door shall have individual locking provision and 4 mm thick transparent glass for clear inside vision secured in a metal frame through rubber gasket. Each door shall have scissor mechanism for receding inside the top of respective compartment which ensures parallel & smooth movement. Each door shall have plastic side end caps as handle which is easy to grip. Each compartment has a storage shelf having Uniformly Distributed Load Capacity of each shelf is 40 Kg maximum. The finish is Epoxy Polyester Powder coated to the thickness of 50-60µ. Adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level & support structure. Geeken Model No.GMS 19 Size

Supplying & Placing back storage unit in completely knock down conditions with an overall size 3000mm X 450mm X 900mm that is to be assembled at site. The top shall be made up of Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The panel shall be in rectangle shape and should be 75mm thick. Veneered portion of work surface shall be finish with PU polish. The edges of the table shall be supplied with solid brass bar strips having cross-section area 25mm X 5mm all around the top. The complete unit shall be made up of medium density fibre-board duly veneer laminate and PU polish. It shall have 4 nos. of door shutter operated with the assistance of soft-close concealed crank hinge and 4 nos. of drawer operated on soft-close ball bearing sliding channel. The understructure shall consist of MS/CRCA powder coated rectangle pipe frame having cross-section area 40X20mm with 1.6mm thick. The unit have to be made in such a way that no gap should be seen in between. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. Geeken Model No.Manhattan 2 Size 3000x450x900

Supplying & placing storage unit with an overall size 1500mm X 450mm X 750mm. It storage should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, top, shutter, facia, shelf, skirting shall be 18mm thick and base 9mm thick. The top and side shall be full round post form at front and other edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 8 nos. of drawer, 1 nos. of adjustable shelf and 2 nos. of shutter. The drawer and shutter shall be operated with roller channel to enable smooth operation and concealed crank hinge with SS handle. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key and shutter shall have MP lock. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380. Geeken Model No.Storage 9 Size 1500x450x750

Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 900mm (W) X 450mm (D) X 1830mm (H). The Almirah shall be supplied with 2 nos. of glass door and 2 nos. of steel door with adjustable shelves. The door shall be operated with aesthetically appealing snap fit ABS plastic handle and concealed crank hinge. The glass shall be used 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel, shelf shall be made of high yield strength 0.8mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. To protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick. Geeken Model No.GMS 12 Size 900x450x1830

Providing, placing and installing a slotted angle rack with an overall size 900mm (W) X 450mm (D) X 1800mm (H). The panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. CRCA slotted angle shall be supplied with 2mm thick having size 40mm X 40mm. All steel components shall be 50-60µ thick (DFT) powder coated after 7 tank pre-treatment process flow. Corner plate (gussets) and fasteners shall be provided for complete assembly. Geeken Model No.GMS 20 Size 900x450x1800

Overall Approx Dimension: 400mm L x 400mm W x 820mm H. SS Top with three sides SS railing. Square Box of CRCA Steel. Square legs fitted with Rubber Shoes. Pre-Treated and Epoxy Powder Coated Finish. Geeken Model No.GK 2002 Size 400x400x820

Providing, placing and installing a slotted angle rack with an overall size 900mm (W) X 600mm (D) X 1800mm (H). The panel shall have 5 nos. of shelves made up of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. CRCA slotted angle shall be supplied with 2mm thick having size 40mm X 40mm. All steel components shall be 40-50µ thick (DFT) powder coated after 7 tank pre-treatment process flow. Corner plate (gussets) and fasteners shall be provided for complete assembly. Geeken Model No.GMS 20 Size 900x600x1800

Supplying & placing storage unit with an overall size 1200mm X 400mm X 1850mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The storage shall have 6 nos. of fixed shelf and 6 nos. of door shutter for ease of opening. The shutter shall be operated with concealed crank hinge and SS handle. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380. Geeken Model No.Storage 2 Size 1200x400x1850

Providing and supplying bed side table with an overall size 450mm X 450mm X 550mm. The top, side, back, facia shall be made up of 18mm thick pre-laminated particle borad of grade II of IS 12823 with approved laminate and finish as per approved shade. The unit shall be supplied with one nos. of drawer and one open compartment. The drawer shall be operated with roller sliding channel. Geeken Model No.Capila Bed Side Unit Size

COMPACTORS Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to undercarriage. Compactor height from ground should be 2080 mm (1980 body + 65 undercarriage + 35 channel system). The body including shelves shall be given antirust surface treatment & powder coated with epoxy polyester powder. It involves an 7 step treatment, Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets & shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts & bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. Geeken Model No.Organise 6 Size Drive way

3 Bay Single Static Geeken Model No. Size 2745x455x1980

3 Bay Double Static Geeken Model No. Size 2745x910x1980

3 bay single last Movable (Lockable) Geeken Model No. Size 2745x455x1980

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade 'D' confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to undercarriage. Compactor height from ground should be 2080 mm (1980 body + 65 undercarriage + 35 channel system). The body including shelves shall be given antirust surface treatment & powder coated with epoxy polyester powder. It involves an 7 step treatment, Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets & shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts & bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. Geeken Model No.Organise 5 (Drive Type) Size 1 Way

1 way Single static Geeken Model No. Size 915x455x1980

1 way Double movable Geeken Model No. Size 915x910x1980

1 Bay Single last movable (Lockable) Geeken Model No. Size 915x455x1980

Semi Fowler Bed Has the facility to the back sections by crank mechanism. Overall Approx Dimension: 2010mm L x 900mm W x 600mm H. Pre- Treated and Epoxy powder Coated finish. Detachable polymer mooulded Head and Foot Panel. Geeken Model No.GK 1005 Size 2010x900x600

Providing and placing in position single bed with an overall size - 1925mm (L) X 965mm (W) X 1000/450mm (H) without mattress. The construction of the bed shall be supplied in knock down with metal frame made out of MS/CRCA steel pipe having cross-section area 50mm X 25mm with 1.2mm thick. Head and tail panel shall be constructed from CRCA round pipe having dia. 19mm X 1.2mm thick and 15.8mm with 1.2mm thick. The mattress panel shall be made of 19.05mm X 19.05mm square pipe with 1mm thick. The legs shall be made of M.S.E.R.W pipe having cross-section area 40mm X 40mm with 1.2 mm thick. All metal part shall be powder coating finish with DFT(Dry Film Thickness) - 35µ min. The PPCP shoes shall be insert into bottom of legs for avoid skretches on the floors. Geeken Model No.Hostel 2 Size 1925x965x1000

Supplying and placing single bed with an overall size 2060mm (L) X 1131mm (B) 930mm (H). Head and tail panel shall be made of 18mm thick Pre laminated particle board and baton shall be made of 32mm thcik MDF board duly bull nose shape. Sides baton shall be made of 32mm thick MDF board (one side full round post forming) and 18mm thick particle board with 2mm thick PVC edge banding . The edge banding shall be pasted with hot melt glue at 200 degree Celsius. Mattress panel shall be made of 18 mm thick particle board. The understructure shall consist of MS channles in 1mmm thickness. Horizontal and Bottom Plinth shall be made of 25mm thick Pre laminated particle board. Geeken Model No.Hostel 5 Size 2060 x 1131 x930

MATTRESSES 4'' Mattresses Geeken Model No. Size

5'' mattress Size 1829x914 Geeken Model No. Size

STRETCHER Overeall Approx Dimension- 2160mm L x 560mm W. Removable Stretcher top. Four 150mm wheel two with lock. Complete Stainless steel Constructionn Geeken Model No.GK 8003 Size

LABORATORY Overall Size 2480xx L x 1540mm D x 900mm H made up of C Frame understructure. All sheet metal items shall be of CRCA as per IS 513:1994. C frame made of rectangular pipe with cross section of 60mm x 30mm & 2mm Thick with feet tolerance of -5 ton +20mm & skirting at bottom side. Horizontal members to connect c frame shall be made of rectangular frame of CRCA MS 2mm Thick oif pipe dimension 60 x 30 x 2. Side cover pamels , back panels should be made from CRCA MS panel of 1mm thick. Fixed type CRCA MS double sided regent shelves consisting of 2 stage hoizontal strorage shelves haing 8 electrical switches 16A & 8 Sockets 16A with 4 six module plate. Welded understorage cabinet with intersection of vertical and horizontall members having provisions to be relocated anywhere as an independent unit. Doors shall be assembled with hinge assembly. Imntermediate horizontal channels should be provded betwwn door and drawer. Shelf should be bend panel with 20mm height. Single piece drawer traysupported on LH and RH ball side to be provided . Knee space panel shall be in 22 gauge construction. 6 understorages of size 600mm W x 530mm D x 635mm H should be supplied. Four having 1 drawe & 2 shuters and two having only 2 shutters. Thickness of storage unit LH/RH panels, shutter front, bottom panel, top front , drwer, separator, alingemnet channel, Back panel, shutter cover, Fr. rack strip, top covershould be of 0.8mm thick. handle popypropyele recessed type. lock facility with 80 degree and 10 lever cam lock mechanism. Shutter should be of single type construction. Ball slide 500mm length (req only for drawer unit). shutters should have provision of roller catch. Worktop should be 19mm (+/-2mm) thick black granite worktop with exposed edges chamfered. Two SS sink of size 490mm X 405mm X 200mm.Bowl size 430mm x 350mm. All steel frame works should be pre treated with superior powder coated finish. Geeken Model No.Lab 4 (Double side + regent rack + sink) Size 2480x1540x900

FIRE FIGHTING WORKS Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.

100 mm dia

80 mm dia

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0 - 15 Kg / cm2 .

Supplying and Fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS 926.

Providing & fixing 25mm dia. UL listed gunmetal inspector test and drain valve with integral sight glass connected to drain line complete in all respects.

Providing & fixing double flanged Metallic expansion with M.S. fixed flanges (PN-1.6) joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required as per specifications.

150 mm dia

65 mm dia

Providing and fixing weather proof lockable cabinet of size not less than 0.9 x 0.6 x 0.25 mtr made out of MS sheet 2mm thick having central opening and 6 mm thick glazed glass doors (Two nos.) suitably marked on the outside with the letters "FIRE HOSE" including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint (Post Office Red) of approved shade as required as per specifications.

SUB HEAD - III - (HYDRANTS SYSTEM) SITC weather proof M.S Door and glass fire door size 2100 mm x 900 mm or as per arch. Supplying, installation, testing and commissioning of weather proof M.S door and glass fire door size 2100 mm x 900mm fabricated from 1.6mm thick M.S. sheets and M.S angle 40mmx40mmx6mm complete with glass, locking arrangements to accommodate the following: -

a) Gunmetal single headed Hydrant valve - 1 No. b) Fire Hoses 63mm, 15 M long with accessories - 2 Nos. c) Short branch - 1 No. d) First Aid hose Reel - 1 No. e) Fire Extinguisher - 2 Nos. f) Fireman's Axe - 1 No. g) Pressure Gauge - 1 No. The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved shade.

SUB HEAD - IV - (FIRE EXTINGUISHERS) Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed.

6kg capacity cylinder.(ABC TYPE)

Providing and fixing fire extinguisher of ISI marked (IS:15638) portable chemical fire extinguisher, water (gas pressure) type capacity 9 litres with gun metal cap and nozzle and complete in all respects including initial fill and wall suspension brackets as required as per specifications.

SUB HEAD - V - FIRE PANEL Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 ± 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2.0mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc.including all cabels ,wires,glands etc complete in all respect . necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming:

1 No.630 ampa TPN switch fuse unit with HRC fuses complete.

Three phase indicating lights with 2A Control MCB'S.

Bus Bar

Electrolytic high conductivity three phase and neutral busbar rated at 800 amps having a current density of 1 amp per Sqmm suitable to with stand symmetrical fault level of 25 MVA at 415 volts.

Outgoings:

2 nos. 400 amps TPN MCCB (25 KV) "C" curve with rotary hanle.

2 no. 63 amps TPN MCCB (25 KV) "C" curve with rotary handle.one for jockey pump

3 Nos. panal type ameter for each pump with CTS ASS etc.

Phase Indicating lamps with each starter.

All inter connecting busbar/pwer cable control cable etc inside panal shall be fully automatic DE starting panel complete with battary charger Hooter Anunciator window, transformer, Rectifier, Ameter,Volt meter,push button, Relay etc complete as required.

The motor control panel shall be prewired with colour coded wires with identification labels cpmplete in all respects as

SUB HEAD - VI- FIRE SUPPRESSION SYSTEM All Low Volatge items shall be approved by Architect and contractor shall submit OEM Quotation with Certificate at the time of Bidding.

Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based 4 Kg Novec 1230 System with DLP valve, push in connector for tube, 4Kg Novec 1230 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system activation, 25 Mtrs Linear pneumatic heat Detection Tube with all necessary fittings & support and Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System. Approved Make

Supply, fixing, testing and commissioning of Automatic Linear pneumatic Tube Detection based 22.5 Kg Co2 System with IHP valve, push in connector for tube,22.5 Kg Co2 gas, mounting bracket, End of Line adopter and low pressure switch for monitoring system activation, 15 Mtrs Linear pneumatic heat Detection Tube with all necessary fittings & support, 2 Nos of Discharge Nozzles with Discharge High Pressure Hose and Pipe Network and Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The Control Panel should have provision for integration with Fire Alarm/SCADA/BMS System. Approved Make

Supply, fixing, testing and commissioning of 1x100 Ltrs Automatic Low Pressure Water Mist Fire detection and suppression system, Including 100 ltr Water storage tank made os Stainless Steel grade 304, Nitrogen pressurized Cylinder, Stainless Steel Schedule 5 Seamless Piping, C-EL Electric Actuator, ,NRV, strainer Low pressure water mist nozzle(FM Approved) 4 Nos, instruments( Pressure regulator, pressure gauge, pressure switch, levele switch), CEL panels, piping supports, release system, control cable system supplied & design calculation including Intrinsically safe Probe Type Heat Detector,Release Panel, Manual release & Abort system complete in all respect. Approved Make

Supply, fixing, testing and commissioning of 1x40 Itr completele system with CCOE approved high pressure, seamless Peso approved Cylinders having sutable 40 ltr water capacity & suitable to store UL/FM/VDS approved Novec 1230 /FK5-1-12 gas working upto 50.0 bar pressure with UL/FM/VDS listed valve assembly and electric solenoid switch. The system shall be fitted with low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV. Electrically operated control head capable of being electrically operated from the fire detection & control, Pressure operated control head which shall allow for pressure actuation of gas mounted directly on top of cylinder valve, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distrbution Novec 1230 (FK5-1-12) gas to flood the hazard area as per requrement. Electrical non conductive,Novec 1230 (FK5-1-12) required as per NFPA 2001 latest addition 4.5% Design Concentration. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to Fire Alarm System. Approved Make

ELECTRICAL WORKS Telephone cable in existing conduit RJ 45 socket for Lan cat 6 Polycab Cat No SLV0400401/02

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed copper conductor, armoured telephone cable in the existing surface / recessed steel/ PVC conduit with suitable clamps, saddles and including making terminal joints complete as required.

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit with suitable clamps, saddles and including making terminal joints complete as required.

Providing, fixing, connecting & testing of Telephone Tag Block krone type in a suitable size 1.6 mm thick dust and vermin proof Sheet steel enclosure duly painted by synthetic enamel over anti corrosive primer, lockable and hinged cover with provision for cable through glands complete in all respects.

10 pair krone

20 pair krone

30 pair tag block

50 pair krone

100 pair tag block

250 pair tag block

500 pair tag block

Supplying, erection, testing and commissioning of following tap off / splitter as per specification in 1.6mm thick CRCA sheet steel enclosure for CATV system.

4 Way splitter box

S/F 'C' Series MCB :- Supplying and fixing following 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps TP (Outgoing for Vertical DB)

SUB HEAD IV):-INTERNAL LIGHTING FIXTURES & FANS Supply of LED Tube Light with Batten Suitable for 1X36 Watt LED Tube Light Complete Including tube etc on surface complete in all respect of Polycab Cat No Intenso LED Batten AL 4 Feet 36W 6500K 2 or equivalent

Supply of LED Tube Light with Batten Suitable for 1x24 Watt LED Tube Light Complete Including tube etc on surface complete in all respect Polycab Cat No Intenso LED Batten SQ PC 4ft 24W 6500K 2 or equivalent

Supply of LED Tube Light with Batten Suitable for 2x24 Watt LED Tube Light Complete Including tube etc on surface complete in all respect Polycab Cat No Intenso LED Batten SQ PC 4ft 24W 6500K 2 or equivalent

Supply & Fixing of SEARCH LIGHT With High Intensity, Precision Spot Beam, Hand Held, ABS Body, Shoulder Strip, Parabolic Reflector, Inbuilt Timer, Rechargeable Sealed Lead Acid Battery of 12v-7Ah in Halogen Series and 4v-4ah/4v-6ah in LED Series, Good Backup, in-Build SMPS Charger etc

Floodlight LED luminaire 150 Watas with high pressure die cast housing with IP66 deg of protection of Polycab Cat No. PCGLF T1 01 150 or equivalent

Supply, of Post Top Lantern suitable for 25 watt LED Light, including 1x25W LED lamp complete including grouding 40 mm long G.I. pipe of suitable size with all accessories & Control Gears etc. as required.of Polycab Cat No PCGLPT 01 25 C 1 or equivalent

SUB-HEAD -V : EARTHING Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

SUB HEAD(VII):- UPS SYSTEM Supply, Installation, testing & commissioning of 1x 10 KVA UPS system configuration with 3Phase Input and 3 Phase Output True On Line Double Conversion UPS Inbuilt Isolation Transformer, IGBT based including Battery Circuit Breaker for Each Module CRCA housing with all required fixing accessories and hardware,In-Built Manual Maintenance by-pass, Sealed Maintenance free batteries for 15 Min back up, Battery Racks MS Powder Coated etc complete as required.

Providing and Fixing of 19-inch rack mount patch panel, 1U, 6 port loaded with Adapter Plates SC Style approved make

Supply, Installation, testing & commissioning of 1x 20 KVA UPS system configuration with 3Phase Input and 3 Phase Output True On Line Double Conversion UPS Inbuilt Isolation Transformer, IGBT based including Battery Circuit Breaker for Each Module CRCA housing with all required fixing accessories and hardware,In-Built Manual Maintenance by-pass, Sealed Maintenance free batteries for 15 Min back up, Battery Racks MS Powder Coated etc complete as required.

Installation testing commissioning of TPN DBs of 4 way to 12 way including incoming outgoing MCBs,RCCBs,incoming submains wire and outgoing connection & termination of circuits / wires complete in all respects

Installation testing commissioning of SPN DBs of 4 way to 16 way including incoming outgoing MCBs,RCCBs,incoming submains wire and outgoing connection & termination of circuits / wires complete in all respects

SUPPLY OF LIGHTING FIXTURES Supply of 50W LED Flood Light Complete Including complete in all respect of Polycab Cat No PCGLF T1 02 50 8 or equivalent

Supply of WALL BRACKET LIGHT Complete Including tube etc on Wall complete in all respect of Polycab Cat No LED Wall Mount Fixture - GL 12404 or equivalent

SUB-HEAD -VII : LIGHTNING PROTECTION SYSTEM Supply of LPI ESE Stormaster type Lightning Protection complete with the Lightning Air Terminal - Configured as a Spheroid which is comprised of separate electrically isolated 4 panels surrounding an earthed central finial. The Insulation material used to electrically isolate the panels (anodisied aluminum) shall be comprised of a base polymer which provides high Ozone & UV resistance with a di-electric strength of 24-38 KV/mm tested as per NFC 17-102 As per NF C 17 – 102, the ESE air terminal shall be tested with the “Switching Impulse Voltage” of 100 KA and certified by an international testing laboratory. The early streamer emission terminal shall be tested & certified by CPRI (Central Power Research Institute), Govt of India for the Impulse current of70 KA (8/20 micro sec) with 5 positive & 5 negative impulse. The ESE terminal shall not have any electronic circuit or any batteries inside to operate and it shall not depend on wind or solar to operate.The ESE lightning protection design has to be submitted and approved by the electrical engineer in charge before the installtion so as to confirm the appropriate position of the ESE terminals. The ESE Stormaster terminal shall offer a protection radius of 79 Metres with the Level -I protection and preferably to be mounted on the roof top & centre. Approved make

ESE Air Terminal should be supported with certification by the manufacturer certifying the compliance as required in the new test guidelines in Annex 'C' of revised NFC 17-102 version. 2011.

Annex 'C' calls for the following tests and due certification required from the ESE -manufacturer for

a). General Test (Marked Test)

b). Environmental Test

c). Electric Test Test

d). Early Emission Test

GI Mast

5mtr (with coupler )suitable GI Mast . for mounting the terminal & adaptor to mount the Lightning arrester.

LPI STRIKE COUNTER ( LSR2) Supply of Lightning Strike Recorder - 7 digits electro mechanical display to record the lightning current in an IP 67 enclosure with the minimum sensitivity of 1500A & maximum capacity of 220 KA (8/20 micro second waveform). The recorder is of non-resettable type with the electro-mechanical display. • LCD screen is not permitted as it may depend upon the battery life to energize the LCD. • Tested & certified inline with the ese lightning arrester in an international laboratory for an impulse current of more than 450 KA as per IEC 60-1:1989 standard. • Tested & certified by CPRI (Central Power Research Institute), Govt of India for the Impulse current of 45 KA with 5 positive & 5 negative impulse. Approved make

Test Link Joint Supply of weather proof thermoplastic insulated, shock proof, dust & rust proof enclosure of suitable dimension.

MAINTENANCE FREE CHEMICAL GEL EARTHING SYSTEM Supply of advance chemical gel earthing system for the proper dissipation of fault / leakage current to the ground and ensure the continuous electrical connectivity and proper functioning to the electrical system. The earth rod shall be of UL listed & CPRI tested 3 mtr long 17.2 mm dia 250 microns copper bonded steel rod along with 50 Kgs of JK RESLOW Resistance Lowering Grounding Minerals. The chemical compound should be tested and certified by any International accredited and BIS (Bureau of Indian Standards) accredited laboratory. The testing laboratory should be ISO 9001 & ISO 14001 certified. The UL listed copper bonded rod also should be tested & certified from CPRI for a short circuit current of 31.5 KA or more. The UL listing shall be punched / engraved on the rod for the physical verification at site. The engravings shall contain the following details - UL Control number, Dimension details of the rod, Product model number & UL certificate reference number as per detailed technical specification attached.

To ensure the electrical conductivity, 25 Kgs (per pit) or more resistance grounding minerals per earth pit / earth rod shall be used along with the copper bonded rod. The chemical compound shall be tested for the contents from BIS (Bureau of Indian Standards, Govt of India) & NABL accredited laboratory in India. The testing laboratory shall be an ISO 9001 & ISO 14001 certified. As per IEEE 80-2013 (Clause 14.5 d), the grounding minerals shall be tested & certified for the resistivity of less than 0.12 ohm-mtr. The grounding minerals should be ROHS certified to ensure it does not pollute the ground water as per technical specification attached. Approved make

POLYPLASTIC CHAMBER Supply of heavy duty weather proof environment friendly polyplastic earth pit chamber with cover of auto-locking facility with the following dimensions - 254 mm dia (top), 330 mm dia (bottom) and 260 mm height. 4 knock-out openings are provided for the easy interconnection of earth strips between the earth pits to form a grid. Earth pit Chamber Cover Should be tested & Certified for 9 Ton load bearing capacity from National Test House

Down Conductor (70SQR MM COPPER CABLE )

Installation Installation of complete lightning protection system from Sr. No 210 to 216 with down conductor rooting & Earthing Installation

SUB HEAD(VIII):- UPS SYSTEM Supply, Installation, testing & commissioning of 1x 100 KVA UPS system configuration with 3Phase Input and 3 Phase Output True On Line Double Conversion UPS Inbuilt Isolation Transformer, IGBT based including Battery Circuit Breaker for Each Module CRCA housing with all required fixing accessories and hardware,In-Built Manual Maintenance by-pass, Sealed Maintenance free batteries for 15 Min back up, Battery Racks MS Powder Coated etc complete as required.Note :- Contractor shall have submit shop drawing and GA drawing and get approval by engineer in charge before inplementation.

SUB HEAD(IX):- CCTV SYSTEM GENERAL NOTES 1. All CCTV camera & software, CCTV Analytic Solution and command and control application proposed in the RFP / NIT should be from the same OEM. If 3rd party software from list of approved makes is provided, VMS Software provider should provide written confirmation for compatibility report; same should be cross-signed by Camera OEM.

2.The Video Management Software should be from a CMMI-Level 5 company

3.All CCTV cameras offered in the project should be UL & CE and FCC certified. RoHS ( Environment) is mandatory certification for all cameras.

4. All the CCTV cameras & VMS should be ONVIF compliant to maintain the open/heterogeneous environment. The ONVIF compliance should be of latest standards i.e. Profile S, G, Q. The Quoted Model Number of CCTV and the quoted VMS should be available in ONVIF webiste with profile S&G on the date of Bid Submission.

5.OEM for CCTV shall have its own/authorized CCTV service/repair facility in atealst two metropolitan regions for last 5 years.

6. OEM for Camera & Software should have its own registered company in India. Company held through multi-national parent holding company should be declared. Acceptable origin of manufacture’s parent company are India, USA, & EU countries.

7 Certificate of registration in India should be submitted as documentary proof. Origin of parent company has to be declared.

8. The OEM entity in India should have a minimum average turnover of Rs.500 Crores in the last 5 financial years in electronic security business. Proof of such document has to be provided while tender submission.

9. The CCTV OEM should have completed minimum 15 years of business operations by March 2019, in India. If the OEM is part of larger group/parent company diversified into multiple manufacturing business, only CCTV division would be taken into account for qualification purpose. Any representation through a channel/business/Joint-Venture partner or dealer or distributor shall not be considered as OEM. This is to ensure that the OEM is Serious about its business in India and has been consistently doing Business in India.

10.OEM for Camera/VMS/DVM shall be a profitable company for last 5 years. Proof of such document is to be provided while tender submission verified by a chartered accountant.

11.Offered CCTV solution should be seamlessly integrated with other electronic security system for Access Control using controllers & card readers

12. The OEM for CCTV camera should have atleast 500 employees on its payroll in India. Any OEM which is a part of a larger group company but meeting the 5000 employee criterion is also eligible. OEM to submit declaration Letter from HR dept.

14.The parent company of OEM or OEM itself shall have atleast one CMMI Level 5 software Research & Development center in India with minimum 1000 employees working in Software R&D

16.All the bidders to confirm that they will have to conduct successful demonstration/ proof of concept (POC) for all IP cameras along with VMS respectively along with software and other accessories.

17.All the documents submitted should be ink signed and stamped by competent authority or authorized signatory.

18. Cyber Security Point- The Quoted CCTV cameras should have Cyber Security Certification

19. Camera OEM should have supplied at least 3500 nos. of cameras in a single order with any state / Central Govt. any other State or Central undertakings and Corporations in India.

20. Contractor shall have to submit Shop & G.A drawing and technical data sheet and get approval from engineer in charge before implementation.

Supply Installation, Testing, commissioning of IP CCT Surveillance System - Ranchi Court

Indoor Dome camera 2 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Dome Camera, 1/2.8" CMOS, 2 MP @ 60 fps or better, triple stream, Min. Illumination required 0.01 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 1920 × 1080, triple stream, 2.7–12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, 3 IR LEDs Smart IR with upto 20m IR distance, S/N ratio - 50 dB min, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265, H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S , Profile G & Profiel Q compliant, UL, UL CAP, CYBER SECURITY, CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by Engineer in charge Approved make

Bullet Camera 2 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/2.8" CMOS, 2 MP @ 60fps , triple stream, Min. Illumination required 0.001 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 1920 × 1080, triple stream, 2.7–13.5 mm motorized focus & zoom lens, S/N ratio - 50 dB min, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265,H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, Profile G & profile Q compliant, UL, UL CAP, GDPR, CYber Security certified,CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge Approved make.

Bullet Camera 4 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Bullet Camera, 1/3" CMOS, 2 MP @ 60fps , triple stream, Min. Illumination required 0.01 lux @ F1.6 (color), 120dB True WDR, Min. Pixels 2560x1440, triple stream, 2.7–12 mm motorized focus & zoom lens, S/N ratio - 50 dB min, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 2 In/ 1out, PoE, H.265+, H.265,H.264 High Profile and MJPEG, PoE Class 3 and 12V DC, IP 67, IK 10 vandal proof, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, Profile G & profile Q compliant, UL, UL CAP, Cyber Security certified,CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge Approved make

PTZ camera - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light PTZ Camera with auto tracking, 1/1.9" CMOS, 2 MP @ 25fps, triple stream, Min. Illumination required 0.005 lux @ F1.6 (color) & 0.0005 lux @ F 1.6(B/W) or better, 120dB True WDR or better, Min. Pixels 1920 × 1080, triple stream, 6mm –180 mm or 4.5 to 135mm 30x motorized focus & zoom lens, BLC, HLC, 3DNR, Defog, Electronic Image Stabilitzation, Privacy Mask, Internal / External Illuminatrion range with upto 200m IR distance, Dual channel Audio G.711a/G.711u/AAC, 128GB SD card support, Alarm: 7 In/ 2 out, PoE, H.264 High Profile and MJPEG, PoE Class 5 and 12V DC/24VAC, IP 67, IK 10 vandal proof, Having Operating temp range : –10°C to 65° C. Certifications: ONVIF Profile S compliant, UL, CSA 60950-22, CE (EN 50130-4 & EN 55022) , FCC Part 15 & RoHS compliant. to be mount on exisiting pole only, Include Mounting accessories with PTZ Controller Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge Approved make - --

Network Storage Manager(NSM) supporting ONVIF Profile S & G, PSIA, real time streaming protocol (RTSP) standards, emerging technologies in the industry, like 4K resolution, H.265 video compression codec, 3D PTZ control, 360° Fisheye camera and multi-imager/lens camera support, and intelligence events. System proposed shall have scalability of 4 to 64 cameras per NSM with sufficient licenses to record all the cameras in this requirement. NSM shall support simultaneous recording, live monitoring, playback/search of recorded video for up to 4K resolution on all cameras, taking snapshots and viewing presets for PTZ cameras and system management. NSM shall have integrated Dashboard to easily monitor the health and recording status, Flexible retention time / archive time for cameras, Smart Motion detection, Role-based operator privileges supporting Windows and local users, Video Archiving, Multi-stream support, Advanced security features with encryption support for communication between desktop client to NSM and secure https login for Web Client and Mobile apps, Event history and operator log reporting with export to PDF, Crystal Reports, MS Excel/MS Word. NSM Shall support scheduled backfilling of the recordings from the edge storage/SD card of cameras to the NSM using ONVIF Profile G for robust recording against temporary network failure, N+1/N+M recorder failover and failback automatically or manually to have maximum system uptime and recording continuity. - Approved make - -- NSM shall have Intel® Core™ i7-4790, 3.6 GHz or better, Mnimum 8GB RAM, DVD-R/W, 6 GB/s SAS/SATA RAID Card, 2 NIC cards supporting network throughput of 256 Mbps/425 Mbps for Incoming/outgoing, Graphics Adapter - Intel® HD Graphics 530, 4600, or equivalent for local client GPU rendering support, Windows Server 2012 R2 (64-bit OS versions recommended)/Windows 10/Windows 2008 Server R2 SP1 Operating System, Microsoft SQL Express 2012. The NSM shall be complete system for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items, as required as per specification in Annexure A at site of work inline with the Engineer in Charge instructions. Storage must to calculated for 90 days of recording based on 2MP, 25fps on higher native resolution. Contractor should consider the cost of NVR software and NVR server to record all the cameras. Approved make - -- Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge

Network Video Management & Monitoring Software (NVMMS) system with distributed architecture to collect, manage and present video from all the cameras and supports emerging technologies in the industry, like 4K resolution, H.265 video compression codec, multi-imager/lens cameras and 360° fisheye cameras. The NVMMS shall have option to support database redundancy and 1+1 and N+M NSM failover features for unforeseen/maintenance scenarios for increased system reliability. NVMMS shall support NSM's from a multiple location licenced for 90 cameras & 2 users clients, licenses should expandable upto 500 cameras & 10 user clients without any additional version upgrade. The NVMMS should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback from all NSMs, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, General Data Protection Regulation (GDPR) compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated security platform which provides HSDK&API for further integration with 3rd party systems. NVMMS shall have support for iLIDS certified Analytics like intrusion/LoiteTrace. NVMMS Client shall be running on workstation/PC with minimum Intel Core i7-6700, 3.4GHz, 8GB RAM, Windows 10 (64 Bit) OS, DVD R/W, Integrated Intel HD graphics 530 and NVIDIA Quadro NVS 315 1 GB PCIE x 16 LP supporting 4 Monitors. The NVMMS shall be complete system including server for satisfactory surveillance operations with all necessary softwares, licenses, required PC Hardware, Storage, accessories etc., civil, electrical works & peripheral items, as required as per specification at site of work inline with the Engineer in Charge instructions. Approved make - -- Server Specification : Windows Server 2012 Standard 64-bit, Microsoft SQL Express 2012 Single Intel® 6 Core Xeon® E5 2630V2 2.6 GHz, System Memory (RAM): 16GB Hard Disk Drives: Two separate hard drives or two sets of RAID arrays. Disk/RAID set 1 utilizing 7200 SATA or 10K-15K RPM SCSI 146 GB Disk/RAID set 2 utilizing 7200 SATA or 10K-15K RPM SCSI 146 GB Network Interface Card (NIC): Dual or compatible pair of NICs, 1 Gbps Human Interface: 102-key keyboard and a mouse pointing device Graphics Adapter: 32-bit color or higher, video resolution 1280x768 pixels, 65K colors non-interlaced Windows Media Player Version 12 For installations where the system is integrated with recording software with more than 500 cameras, install a separate database server. Contractor should consider the cost of VMS software and VMS server along with two client license Original Equipment Manufacturer (OEM) Authorisation letter along with Channel Partner certificate need to submit before implementation and same has be confirmed & Certified by engineer in charge

Surveillance Hard Disk Memory 140 TB for Cameras recording Approved Makes

Layer-3 Fibre Switch, 48 port , Rack mountable, Gigabit Ethernet L3 fixed configuration chassis in a 1U form factor with 20 SFP+ ports, one optional module slot. Front to back cooling. The chassis should include a AC redundant Power supply, IP4/ IPV6 Routing, VRRPv3, virtual chasis etc., complete with all interconnections, terminations, crimping etc complete as per technical specifications and as required Approved Makes --

PoE Switch 24-Port, Rack mountable PoE Layer II Managed Gigabit Ethernet chassis in a 1U form factor with 24 PoE 10/100/1000 BaseT ports, 2 fixed SFP+ (1G/10G*) ports complete as required - Approved Makes

PoE Switch 8-Port, Rack mountable Layer II Managed Gigabit Ethernet standalone chassis provides 8 PoE RJ-45 10/100/1000 BaseT, 2 SFP/RJ-45 10/100/1000 BaseT or 100/1000 BaseX combo and 2 SFP Gigabit uplinks ports with internal AC power supply (120W PoE), 10 Gigabit SFP+ stacking module with 1m long SFP+ direct stacking cable etc complete as required - Approved Makes

65" LED TV Display, VGA and HDMI output port, USB port Approved Makes

Client Workstation ( I5 PC, with 4 GB RAM and 1 TB HDD, 10/100 Mbps Ethernet card, USB connection and internal modem, Microsoft(R) Windows(R) 7 OS Professional Enterprise, Web Server Software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and antivirus software with 22" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad.) Approved Makes

UPS, online 5 KVA UPS with 35 AH sealed maintenance free batteries complete as required as per specifications. UPS shall be suitable for at least 1 hour battery backup on full load Approved Makes

42U Rack with all accessories and 12 port PDU 800 x 1000 with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required - Approved Makes

24U Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required Approved Makes

CAT 6 Giga speed unshielded twisted pair computer cable with 23 AWG solid copper conductors in existing conduit as required. -

SFP Module as per the requirement.- Approved Make

Misc Accessories Like LC Pig Tails, LC-LC Patch Cord 9/125 SM, Duplex, 2 mts., Patch Cord 2mtr , RJ 45 Connector -

Providing & Fixing of 25 mm dia 1.6 mm thick MS Conduit exposed in ceiling/false ceiling.

24 port Patch panel fully loaded

6 Core SM 9/125 ITU G.657A1 Bend Insensitive, Indoor- Outdoor, CST Armour, Rodent Protected, Double LSZH Jacket IEC 60332-3-22 Fiber Optic Cable

SUB HEAD(X):- FIRE DETECTION & PA SYSTEM Supply ,Installation and Commissioning, Installation and Commissioning of Loop Card which will have 254 devices of both detectors and modules in a single line circuit on any combination, SLC should supports both Class A and Class B wiring.Shall have an LED indication for FIRE,Normal and Redundancy conditions Approval: UL Listed

Supply, Installation and Commissioning of Manual Pull Station -Single Action/Dual action - with back box and Break Glass Rod,shall be resettable by Align key to avoid unauthenticated restorations, Addressable Mini Monitor Module with back box of pull station for monitoring the field NO/NC devices.Shall have Binary Coding Setting Dip Switch,Shall have an LED indiaction for normal and Activate mode. - Approval: UL Listed NOTE: Need to connect with Monitor Module

Supply ,Installation and Commissioning of Addressable Control Module for activating the Notification application devices. Shall have supervisory facility to supervise the auxillary power Supply as well as the Notifcation Appliance Circuits.. Shall have Binary Coding Setting dip switches,Shall have an LED indication for normal working and active Modes - Approval: UL Listed

Supply ,Installation and Commissioning of Addressable Relay Module with Non Supervised Dual potential free contacts.Shall have Binary Coded Dip Switch address settings,Shall have an LED indiaction for normal and active modes Approval: UL Listed

Supply ,Installation and Commissioning of Addressable Monitor Module for monitoring the field NO/NC devices.Shall have Binary Coding Setting Dip Switch,Shall have an LED indiaction for normal and Active Modes - Approval: UL Listed

Supply ,Installation and Commissioning of Fault isolator Base / Module capable of monitoring shorted loop circuit and automatically restore communications when shorted conditions are corrected

Supply,installation,Testing and commissioning of Responce Indicator Alarm status is indicated By Red colour LED, Operates on 12 VDC, Dual LED’s for 360deg visibility, Flush / Ceiling wall mount, Operating Voltage : 12 VD.C, Operating Current : 10mA, Alarm Indication : RED LED with required accessories

Supply,Installation, Testing and commissioning of 24VDC Power Supply with 5 amp rating,shall provide the supplies to Beam detector/Conventional Sounders/Strobe,Shall have LED indications for Power supply ON,battery Fail,Battery Charging etc,Shall have inbuilt battery charging circuit

Supply,Installation, Testing and commissioning of Conventional Sounder cum strobe with 24V DC, Audiable Sound 75 db @ 1 mtr range (16 V DC). It is used for Fire, Burglar & Emergency Alarm System, Low current consume @ 47 -73 mA Candela: flashing every second, 4 candela settings:15/30/75/110cd output and 2 different tone audiable sound. - UL Listed

Supply,installation,testing and commissioning of 2 core x 1.5sq.mm twisted pair multistand shielded cable for field cabling of speaker in PVC conduit with required accessories like Screws,Glanding,Clamping,Trays etc.

Supply, installation, testing and commissioning of Digital Signal Processing Based Voice Alarm Controller - 4 inputs, supports Paging unit thru RS485 - Digital Amplifier inbuilt of 250 watts - 8 zones inbuilt, each zones shall supports maximum of 250 watts - Zones are expandable in the multiplication of 8 maximum of upto 64 zones - support Remote Paging Unit, integrated with Fire Alarm system, Emergency Inputs, supports 12 nos of Built in Programmable Digital Voice Alert message - 160 characters LCD display - USB connectivity - PC based Router Configuration - 3 levels of password protection - Event log facility - Overriding facility for Emergency Condition, ALL CALL facility - Zone paging facility - inbuilt MIC - 19" Rack Mountable. Works on 230 VAC - Volume control features for all the zones - Supports maximum of 7 slaves with each of 8 zones

Supply,Installation, Testing and commissioning of Digital Amplifier of 250 watts output, Class D amplifier - Low Heat dissipation - integrated with Slave console - Power ON LED indications - 19" RACK Mountable -

Digital Voice Evacuation System Expander - Zones from 9 - 16

Supply ,Installation,Testing and Commissioing of 6W Ceiling Mountable with tapping of 1.5, 3 & 6 Watts output with impedance of 100V Approved Make

Supply,Installation,Testing and Commissioing of 42U Rack for the required height of 19 " width with Exhaust fans and Power Sockets and Door with Lock arrnagements,etc.,

Supply installaion testing & commissioning of Fire Fighter Telephone System - comprising of Master Control Panel with 8 Zone Location Alarm Indication, 8 nodes - Each Node shall cover 8 Station - Maximum of 64 Telephone Station - Audio, Visual Indication to alert the operators - Group or All Call facility - full Duplex Audio conversations - Master to remote, Remote to Master Calling facility - Operating Voltage: 230V Input and DC Output 24V @ 100 mAmps Max. - Flush Mounted/Wall Mounted with suitable Back Box, etc. - Operating Temperature: 0 - 49◦ C - Humidity: 93 + 2% RH - it compiles with BS 5839 PT 92002 .--

Supply, Installation, Testing & Commissioning of Fireman's Phone Jack with all mounting accessories, complete with MS Powder coated Junction Box for mounting on Surface, Cable Lugs at Ends and all required accesories for mounting at site complete as requried. --

Supply, Installation, Tesing and Commissioning of 2 way communication Fire Fighter's Handset. Complete as required as per technical specification. --

Supply,installation,testing and commissioning of 2core x 1.5sq.mm twisted pair multistand shielded cable for field cabling of speaker in PVC conduit with required accessories like Screws,Glanding,Clamping,Trays etc.

Contractor shall have to submit shop & G.A drawing and technical data sheet of all above said items and get approval from engineer in charge before implementation.

SUB HEAD(XI):- LAN SYSTEM Providing and Fixing of CAT 6 Giga speed cable exceeding, Cat6 standard complete as required approved make

Providing and Fixing of 24-port loaded, Modular Jack Panel, 1U (For Data and voice UTP Field Cables)approved make

Providing and Fixing of Slime line RJ45 to RJ45 Cat6 UTP Patch cord ( Data Rack end) = 3 Feet approved make

Providing and Fixing of Slime line RJ45 to RJ45 Cat6 UTP Patch cord ( Work Station end) = 7 Feet approved make

Providing and Fixing of 2 Port Iconable Faceplate with I/O -White approved make

Providing and Fixing of 42U Floor Standing Rack with fan and power strip with spike arrestors approved make

Providing and Fixing of 15U Wall mounted Rack with fan and power strip with spike arrestors. Approved make

Providing and Fixing of 6-core out side plant cable -Corrugated Steel Tape Armoured , Loose tube Gel Field ,50/125 micron OM3 MM Cable -(2 Cable run from Server room to hub room ) approved make

Providing and Fixing SC Pigtail & SC Adapter Unit for 6 Multimode Fibres. approved make

Providing and Fixing of 19-inch rack mount patch panel, 1U, 24 port loaded with Adapter Plates SC Style approved make

Providing and Fixing of 19-inch rack mount patch panel, 1U, 6 port loaded with Adapter Plates SC Style approved make

Providing and Fixing of OFC patch cord -3 Mtr. Long. Approved Approved Make

Providing and Fixing of Switch with 24 x 10/100/1000 Base T Ports , 4x1000 Base X Ports ( Combo Shared ) and 2 dedicated stacking ports with min Stacking Bandwidth of 40Gbps or more as technical specifications enclosed etc. as required approved make

Providing and Fixing of Layer 3 Switch having 20 x 10/100/1000 Base T Ports, 8 x 100/1000 Base X Ports and 4 1G/10G SFP+ Ports with dual Internal Redundant PSU and field replacable Fans, The switch should have support for additional 2 x 40G QSFP+ ports i

Providing and Fixing of 1G Module For Fiber Connectivity approved make It should be of same make as that of Switch OEM

Providing and Fixing of Network Management software to cater minimum 150 devices from day one and should be scalable up to 500 devices as per detailed specification attached approved make. It should be of same make as that of Sw

Wi-Fi Wireless Controller PC with Cloud Based Software - Approved Make

Wireless Access Point Type 1 802.11ac Wave-2 4×4:4 Enterprise Wi-Fi Access Point, 2.30 Gbps wireless throughput and 1 Gigabit wireline ports, Dual-band 4×4 : 4 MU-MIMO technology, 170 meter coverage, 180+ concurrent Wi-Fi client devices, Advanced QoS, Anti-hacking secure boot and critical data/control lockdown via digital signatures, unique security certificate/ random default password per device, 4 dual band internal antennas , 14 SSIDs per radio 2.4GHz - gain 4dBi, 5 GHz - gain 5dBi, Support 400+ concurrent WiFi client devices - Approved Make

Wireless Access Point Type 2 - Outdoor Long Range 802.11ac Wave-2 WiFi Access Point, 1.27Gbps wireless throughput and 2x Gigabit wireline ports, Antenna - 2x2.4 GHz, gain 4 dBi, 2x5 GHz, gain 5 dBi, Coverage Range Up to 300 meters Dual-band 2x2: 2 MU-MIMO with beam- forming technology, Support 400+ concurrent WiFi client devices, Advanced QoS, Anti-hacking secure boot and critical data/control lockdown via digital signatures, unique security certificate/ random default password per device, 16 SSIDs per radio, IP66-level weatherproof capability

Enterprise Multi-WAN Gigabit VPN Router, 6 Gigabit ports (2 WAN + 4 LAN), Multi WAN Ports, Embedded controller to manage 300+ WiFi Aps, firewall features including NAT, DMZ, Port Forwarding, SPI and UPnP - Approved Make

Contractor shall have to submit G.A drawing and technical data sheet of all above said items and get approval from engineer in charge before implementation.

SUB HEAD(XII):- EPBX SYSTEM Supply installation testing and commissioning of following complete in all respect as required.Note :- Contractor shall have submit shop drawing and GA drawing and get approval by engineer in charge before inplementation.

EPABX Business Communications Server

- 04 ISDN PRI trunk

- 400 Digital Extensions with Caller ID

- 700 Analogue Extensions with Caller ID

- 100 IP Trunk Lines

With following features:

- Pure IP-PBX - Expandable Up to 2960 Channel - Eco Conscious Product (Eco Mode) - User Concept - Multi Devices, Multi User on the same extension, Web Besed User Interface Portal) - Scalability - Multi Connection system & Centralised Management - Reliable Backup system to Survive System Failures - 1+1 Redundancy (Optional), Simplified Isolated Mode, Remote Maintenance - DECT Wireless system - Mobile Phone Integration - Video Communication - Built-in Call Centre - Automatic Voice Guidance, Monitoring Callers and Call History Report, Auto Recording and Backing Up Data

Patch Cord for IP Phone - --

Adaptor for IP Phone (In case of Non PoE Neetwork) - --

MDF (Krone) 1200 Pair - --

50 Pin Amphonel Jack with 25 pair Connecting Cable (7 Mtr. Length) from PBX to MDF - --

Contractor shall have to submit G.A drawing and technical data sheet of all above said items and get approval from engineer in charge before implementation.

SUB HEAD(XIII):- VIDEO CONFERENCING SYSTEM Supply installation testing & commissioning of following Note :- Contractor shall have submit shop drawing and GA drawing and get approval by engineer in charge before inplementation.

Video Conferencing System- Sharp HD video resolutions up to 4k Ultra HD, 4K (2160p) Output, Runs on Android operating system, Built-in Bluetooth for use with Bluetooth speakers/ microphones, keyboards, data exchange, etc., Integrated dual band WiFi to pair with video and web conferencing service, Built-in 4-MIC array with beam-forming, support for external audio equipment and innovative Noise Shield technology, Advanced camera with 16M pixel CMOS sensor, 90 FOV wideangle lens and ePTZ for easy camera view adjustments, Miracast Support for wireless content sharing to share a presentation with conference attendees, Integrated 1x HDMI in, 2x HDMI out, and USB, 1:4 Parties with Licenses, Complete Kit

Plate for mounting camera

65'' LED-backlit LCD flat panel display, DVI, VGA (HD-15). Component, composite, HDMI HDCP compatible direct-lit LED 1080p & 4K (Full HD & 4K Resolution) - --

LED TV Stand

Audio-Video specialist cables & connectors

Supply installation testing & commissioning of following. Note :- Contractor shall have submit shop drawing and GA drawing and get approval by engineer in charge before inplementation.Approved make

FOR CONFERENCE ROOM PROJECTION (VIDEO) SYSTEM Professional Display panel - 70'' Class (69-1/2'' diagonal) Screen size , Full Array LED Back Light , Full 1920x1080 (1080 p) Resolution, High Brightness(450 cd/m2) and Contrast Ratio (4000:1), PC analogue: Mini D-sub 15-pin x1 , HDMI x 1*3,3.5 mm- diameter min stereo jackx1 , RS-232C D-sub 9- pinx 1

Mount for the above display

Presentation Scaler/Switchers- Resolutions- Upto UXGA/1080p, Video Inputs- 10 HDMI & 2 Computer graphics video on 15- pin HD connectors, Scaled Outputs- 2 HDMI, 22 Output Resolutions- Upto UXGA/1080P

Switchers- VGA (RGB)8 in 1 out Switching System : Input : 4 PC Video (RGB): 0.7 Vpp/75Ω, on VGA (HD-15) connectors , Sync/ Video Gunlock

Desktop Hidden Connection Box -PC Video Input VGA (RGB), HDMI, PC Audio Input Stereo/RCA, Internet RJ 45 (1 No.), Power Point 5 A (1 pcs)

Presentation Gateway - Enables wireless presentation of HD content using laptops , tables and smatphones , support Full HD 1080p and UXGA display resolutions, Provides HDMI® , VGA and analog audio output , Supports upto 32 simultaneous presenter connections , Remote View allows viewing and saving of presentation images through a Web Browser

HDMI Transition system over CAT 6.0:- 4.95 Gbps (1.65 Gbps per graphics chgannel), supports HDMI and HDCP, Upto 100m (330 ft) at 1080i or upto 90 m(295ft) at 1080p

SOUND REINFORCEMENT SYSTEM: (Apisode / Klipsh Gooseneck Microphone- Electret condenser, cardioid, Rated Impedance -120 Ω, balanced, Rated Sensitivity- -35dB(1 kHz 0 dB=1 V/Pa), Phantom Power- 9 -52 V DC, Frequency Response - 60 Hz - 20 kHz

b) Microphone Stand- Input Connector -XLR-3-31 equivalent , Output Connector- XLR-3-32 equivalent

MIC Mixer- 16 balanced microphone/ line input , 16 balanced output 24 bit/48 kHz A/D, D/A conversion , upto 96 kHz sampling rate, 64 bit processing core with upto two high- speed DSP processing chips , Built in digital automatic mixing function

MIC Mixer- 8 balanced microphone/ line input , 8 balanced output 24 bit/48 kHz A/D, D/A conversion , upto 96 kHz sampling rate , 64 bit processing core with upto two high speed DSP processing chips. Built in digital automatic mixing function

Professional Amplifier- Class H , Stereo power 8 Ω-2x 300W, Stereo power 4Ω,2x450W Signal to noise -110dB 1kHz X 40(32dB), Slew rate:- 20V/µs 10 KhZ X40(32dB) Input sensitivity - 0.775V/1.2V(X40/32dB)

Two- way Loudspeaker System - 30W RMS, 120W peak, IMPEDANCE - 8 ohms nominal, SENSITIVITY- 86dB 1 watt/1meter, MAXIMUM SPL-101dB continous, 107 dB peak

TOUCH PANEL & LIGHTING CONTROL SYSTEM: (E lan / Control 4 / crestron) Control System: 3-series Control Engine, one RS-232/422/485 Com port, Two RS 232 COM, 8 IR /serial, 8 relay, and 8 versiport I/O ports , Onboard 512 MB RAM & 4 Gb Flash memory, Expandable storage upto 1TB

Touch Screen-7'' wide screen active- matrix color display 800x 480 wVGA display resolution Smart Graphics support, Built -in microphone and speaker, PoE network powered

Table Top Kit- Provides a 38' fixed operating angle , Provides the choice of a rear or bottom wire exit

PoE Injector-(1) 8- wire RJ45, female 10 BaseT/100BaseTX Ethernet port,(1) 8- wire RJ45, female 10 baseT/100BaseTX Ethernet Pass-thru port and IEEE 802.3 af Class 0 PoE Power Sourcing Equipment output

Integrated Lightning System - Six Channels of dimming or switching . Upto 16 usersettable scenes, even configurable ''rocker'' buttons with customizable label strip, Maximun Per channel- 800 Watts/VA(3.5 Amps @ 230 volts AC/0, Minimum per channel - 25 Watts/ VA(0.108 Amps@ 230 volts AC)

Power supply -220-240 V, Fuse-250V 5A, Glass Door/lockable, Air cooled , Two Nos of Vertical Power Strips , 4 Nos of spin wheels

INSTALLATION, INTEGRATION & COMMISSIONING:

Audio - Video Specialist cables & connectors

Installation & Commissioning charges

Programming Charges for the crestron

FOR HON'BLE JUDGE'S COURT I) PROJECTION(VIDEO) SYSTEM: 55''LED-backlit LCD flat panel display, DVI, VGA (HD-15). Component, composite, HDMI HDCP compatible direct-lit LED 1080p(Full HD)

Wall Mount Kit-Fits most 32''-60'' flat panel display, VESA Acompliance 100x100mm, 200x100mm,200x200mm,400x200mm,300x300mm, 400x300mm 400x400mm,600x400mm,Load Capacity: 80lbs(36.4Kg), Tilt angle:0°/+12°.

AV hidden connection panel with RGB, HDMI, Power

ii) SOUND REINFORCEMENT SYSTEM: a) Gooseneck Microphone- Electret condenser, cardioid, Rated Impedance -120 Ω, balanced, Rated Sensitivity- -35dB(1 kHz 0 dB=1 V/Pa), Phantom Power- 9 -52 V DC, Frequency Response-60 Hz-20 kHz

Microphone Stand- Input Connector-XLR-3-31 equivalent, Output ConnectorXLR-3-32 equivalent

Amplifier -Rated Output-240 W, Input-MIC 1:60 dB* ,600Ω, balanced, phone jack ,AUX 1,2:-20 dB*, 10kΩ, unbalanced,RCA pin Jack , Output-Speaker out: Balanced (floating), M3.5 screw terminal, Low impedance: 4Ω (22V),High impedance: 83Ω(100V), 42Ω(70 V)

Two- way Loudspeaker System - 30W RMS, 120W peak, IMPEDANCE - 8 ohms nominal, SENSITIVITY- 86dB 1 watt/1meter, MAXIMUM SPL-101dB continous, 107 dB peak

iii) INSTALLATION ,INTEGRATION& COMMISSIONING:

Audio-Video specialist cables & connectors

Installation & Commissioning charges

Equipment Rack-8U Power supply-220-240 V, Fuse-260V 5A, Glass Door /locable, Air Cooled ,Two nos of Vertical Power strips, 4 NO. of Spin Wheels

FOR HON'BLE JUDGE'S COURT I) PROJECTION(VIDEO) SYSTEM: 55''LED-backlit LCD flat panel display, DVI, VGA (HD-15). Component, composite, HDMI HDCP compatible direct-lit LED 1080p(Full HD)

Wall Mount Kit-Fits most 32''-60'' flat panel display, VESA Acompliance 100x100mm, 200x100mm,200x200mm,400x200mm,300x300mm, 400x300mm 400x400mm,600x400mm,Load Capacity: 80lbs(36.4Kg), Tilt angle:0°/+12°.

AV hidden connection panel with RGB, HDMI, Power

ii) INSTALLATION,INTEGRATION & COMMISSIONING:

Audio-Video specialist cables & connectors

Installation & Commissioning charges

Equipment Rack-8U Power supply-220-240 V, Fuse-260V 5A, Glass Door /locable, Air Cooled ,Two nos of Vertical Power strips, 4 NO. of Spin Wheels

FOR CANTEEN PROJECTION (VIDEO) SYSTEM: 55''LED-backlit LCD flat panel display, DVI, VGA (HD-15). Component, composite, HDMI HDCP compatible direct-lit LED 1080p(Full HD)

Wall Mount Kit-Fits most 32''-60'' flat panel display, VESA Acompliance 100x100mm, 200x100mm,200x200mm,400x200mm,300x300mm, 400x300mm 400x400mm,600x400mm,Load Capacity: 80lbs(36.4Kg), Tilt angle:0°/+12°.

AV hidden connection panel with all RGB,HDMI, Power

ii) SOUND REINFORCEMENT SYSTEM:

Two -Way Loudspeaker System- 30 W RMS , 120 peak,IMPEDANCE-8 ohms nominal, SENSITIVITY-86dB 1 watt/1 metre, MAXIMUM SPL-101dB continous, 107 dB peak

Amplifier-Rated Output- 120 W Input-MIC 1:-60Ω balanced ,DIN type (5 pins), MIC 2,3:-60 dB*, 600Ω, balanced, phone jack , AUX 1,2:-20dB* 10kΩ unbalanced, RCA pin jack, Output-Speaker out: Balanced (floating), M3.5 screw terminal, Low impedance :4Ω(22V),High impedance :83Ω(100V), 42Ω (70V)

iii) INSTALLATION , INTEGRATION& COMMISSIONING:

Audio-Video specialist cables & connectors

Installation & Commissioning charges

Equipment Rack-8U Power supply-220-240 V, Fuse-260V 5A, Glass Door /locable, Air Cooled ,Two nos of Vertical Power strips, 4 NO. of Spin Wheels

SUB HEAD(XV):- FIRE SUPRESSION SYSTEM FOR SERVER ROOM Supply and installation of FK 1230 total flooding fire suppression system. The system shall be complete UL Listed in 42 Bar pressure. Note :- Contractor shall have submit shop drawing and GA drawing and get approval by engineer in charge before inplementation.

Supply of 80 Litres Capacity Seamless Cylinder CCOE Approved, complete with valve assembly and pressure gauge with a safety burst disc and a safety cap including Valve. The system must be complete UL listed in 42 bar pressure.

Supply of UL listed Brass Electric Control Head operated electrically from the Detection & Control System or locally with a manual lever on the control head.

Supply and filling of UL lsited FK 1230 Fire Protection fluid compound of carbon, fluorine and oxygen CF3CF2C(O)CF(CF3)2).

Supply of UL listed Discharge Nozzles are designed to provide the proper flow rate and distribution of FK 1230 to total flood a hazard area : 360 deg.

Supply of UL listed flexible reinforce rubber Discharge Hose carbon steel ffitting MOC., (80 Ltr. Cylinders)

Supply of Cylinder Strap for 80 Ltr. Cylinder

Supply of UL listed piping agent discharge pressure switch

Supply of Manual Gas release Unit

Supply of Manual gas abort Unit

Supply of sounder with strobe

Supply of Smoke detector with base

Supply of Heat detector with base

Supply of gas discharge indicator housed MS/ ABS housing

Supply of Discharge Pipe with Support and Fittings, CS Seamless to ASTM A-106 Schedule 40.

Supply of 2 C 1.5 SQM armoured copper core cable with all neccessory accessories for the installation

Installation testing and commissioning of the system.

LIFTS Supplying, installation, testing and commissioning of machine room-less(MRL) 16 Passenger (1088 Kg) lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specifications.

Floor: G+2

Travel :10.5 Meters (approx)

Stops and Opening : 3 Stops & 3 Opening

controller: AC Variable voltage and variable frequency

Automatic rescue device complete with dry maintenance free batteries as required

power: 415V 3phase 50 HZ, 4-wire system

type of door: a. car: power operated center opening horizontal sliding, stainless steel scratch proof (moon rock finish)

b. landing doors: stainless steel scratch proof (moon rock finish)

A hand rail not less than 600mm long at 900 mm above floor level to be fixed adjacent to control panel in the lift car

Voice announcement system in the car to announce the position of the elevator in the hoist-way as the car passes or stops at a floor served by the elevator

Lift as per Above description complete as required.

LIFT Supplying, installation, testing and commissioning of machine room-less(MRL) 10 Passenger (680 Kg) lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specifications.

Floor 2: F+1 (first floor to 2nd floor)

Travel :7 Meters (approx)

Stops and Opening : 2 Stops & 2 Opening

controller: AC Variable voltage and variable frequency

Automatic rescue device complete with dry maintenance free batteries as required

power: 415V 3phase 50 HZ, 4-wire system

Car body : Stainless steel (Mirror Gold Finish)

Car door: power operated centre opening sliding door-glass-ss enveloped (Mirror gold Finish)

Car ceiling : sleek (small circular lights)-ss mirror gold finish

car fittings: LED Lights & axial flow fan

car floor: 20 mm recess with granite flooring

landing doors: centre opening sliding door- glass-ss enveloped (mirror finish)

A hand rail not less than 600mm long at 900 mm above floor level to be fixed adjacent to control panel in the lift car

Voice announcement system in the car to announce the position of the elevator in the hoist-way as the car passes or stops at a floor served by the elevator

Lift as per Above description complete as required.

Add 12 % GST

Add 1% Labour Cess

BALKRISHNA BHALOTIA CONST.PVT.LTD