SPECIAL REPAIRS AND PROVN OF CERTAIN E/M WORKS UNDER GE SAUGOR

Amount

Disconnecting and taking down old fitting of fluorescent tube light/HPSV/MH/HPMV of any wattage or size flood lights/street light fittings on pole up to 11 mtr complete all as specifiedn and directed.

S&F 150 watt LED flood light fittings having long life of high power LED with SMD LED exclusive innovative dia cast aluminium IP-66 built in IP-67 electronic driver with APFC, lower THD, open circuit protection, over voltage protection, surge protection up to 10KV with built in SPD & other safety as per IS-15885 part -2, Sec 13, IEC 60598-1 of operating voltage 140-270V avg life 50,000 hours complete manufacture prove all test certificate as per protection for minimum 2 years from manufacturing companies complete all as specified and directed.

S&F 200 watt LED flood light fittings having long life of high power LED with SMD LED exclusive innovative dia cast aluminium IP-66 built in IP-67 electronic driver with APFC, lower THD, open circuit protection, over voltage protection, surge protection up to 10KV with built in SPD & other safety as per IS-15885 part -2, Sec 13, IEC 60598-1 of operating voltage 140-270V avg life 50,000 hours complete manufacture prove all test certificate as per protection for minimum 2 years from manufacturing companies complete all as specified and directed.

S&F LED Street Light fixture with IP-66 protected die-cast aluminium housing and heat resistive toughened glass. LED shall be having LM-79 and LM-80 complied as per L-70 standard. LEDs should be tested for minimum 10,000 burning hours with 5700-6000 K CCT. Maximum power consumption shall not exceed 45W and system lumens shall not be less than 9,000. Optics shall be properly designed with Polycarbonate Lenses to avoid dark patches on the road. Street light without lenses will not be acceptable. Driver shall be 3 stage "Constant Current Constant Voltage" with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60 V DC. Note: (i) The item rate shall deem to include provision of weather proof PVC insulated aluminium conductor cable 1.5 Sqmm, 3 core as required. (ii) Contractor shall produce warrinty certificate and LEDs used in the product shall comply with EN-62471 for photo - biological safety and certificate for the same from manufacturer shall be provided. Luminaire manufacturer shall produce certificate of association with LED manufacturer for minimum two years.

S&F LED Street Light fixture with IP-66 protected die-cast aluminium housing and heat resistive toughened glass. LED shall be having LM-79 and LM-80 complied as per L-70 standard. Maximum power consumption shall not exceed 72W and system lumens shall not be less than 9,000. Optics shall be properly designed with Polycarbonate Lenses to avoid dark patches on the road. Street light without lenses will not be acceptable. Driver shall be 3 stage "Constant Current Constant Voltage" with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60 V DC. Note: (i) The item rate shall deem to include provision of weather proof PVC insulated aluminium conductor cable 1.5 Sqmm, 3 core as required. (ii) Contractor shall produce warrinty certificate and LEDs used in the product shall comply with EN-62471 for photo - biological safety and certificate for the same from manufacturer shall be provided. Luminaire manufacturer shall produce certificate of association with LED manufacturer for minimum two years.

S&F in replacement 40mm bore or next suitable size ( for LED fittings) light grade GI bracket 1.20 mtr long bent to shape by cutting welding and well finishing including MS clamp of flat iron of size 25x5mm suitable length 2 nos complete for steel tubular poles with nuts bolts and painting with two coats of aluminium paint over a coat of primer on MS clamp complete all as specified & directed.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtr below ground level connected to galvanized iron wire 4mm by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber) 1:2:4 type B-1 using 20mm graded stone aggregate copy shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4 funnel wiht wire gauge of 22 gauge (0.68mm) 8 mesh per liner inch, 50 mm thick cover of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with 8 mm four MS bars @ 80mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, all excavation and earth work & connectiing the earthing to an earthing test point as specified and testing on complete all as specified and directed.

S&F timer switch for street lights control for 3 KW Single Phase rating consists of the following items :- (a) Swadeep-02EC-3KW1P (b) contactor AC3 25 Amps - 01 No (c) Incoming MCB of 25 Amps - 01 No (d) Outgoing MCB of 25 Amps - 01 No (e) complete single phase circuit wiring

S&F timer switches for street lights control for 5 KW three Phase rating consists of the following items :- (a) Swadeep-02EC-5KW3P (b) contactor AC3 16 Amps per phase - 03 No (c) Incoming MCB of 20 Amps - 01 No (d) Outgoing MCB of 20 Amps - 01 No (e) complete single phase circuit wiring

S&F junction box Triple Pole and neutral enclosure compression gland 2 with connector and clamp for pole mounting with two nos of nut bolt and washers and socket complete of size not less than 12"x10"x4" complete all as specified and directed. Make - Sintex/Hensel

S&F junction box Single Pole and neutral enclosure compression gland 2 with connector and clamp for pole mounting with two nos of nut bolt and washers and socket complete of size not less than 12"x10"x4" complete all as specified and directed. Make - Sintex/Hensel

Taking down LT UG cable PVC insulated , bedded armoured heavy duty electric cable 1100 volts grade with aluminium conductor of any size laid in trenches or fixed on wall/floor/poles from trenches complete all as specified and directed.

Supply, laying, connecting and testing in replacment of cable XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 Volt grade cross sectional area 16 Sqmm, 4 core complete all as specified and directed.

All as per Srl item No.13 above but of size 10 Sqmm, 4 core -ditto-

All as per Srl item No.13 above but of size 10 Sqmm, 2 core -ditto-

Excavation in trenches in soft/ loose soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr depth for laying of cables/poles or foundation and getting out complete all as specified and directed.

Returning, filling, including spreeding leveling watering and well ramming in layers not exceeding 25 cm apart complete all as specified and directed.

Removing of surplus excavated soil to distance not exceeding 50 Mtr from starting point and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

M&L for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable to trenches complete all as specified and directed. Note:-Punned thickness shall be measured and paid

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat size 250mm x 150mm x 40mm complete all as specified and directed.

S&F in replacement galvanised iron pipe light grade 40 mm bore (ISI marked) with all fittings laid in trenches or on pole, crossing of road,fixed on wall for protection of cables complete all as specified and directed.

S&F in repairs flat cable flexible copper of size 1.5 sqmm 3 core, 1100 volt grading complete all as specified and directed.

Supply, installation, testing and commissioning of LT panel outdoor type floor mounted made out of 3.15 mm thick CRCA sheet dust & vermin proof of IP-64 protection comprising of the following, duly powder coated and pre wired as per standard engineering practice the panel manufacture should have got any of his earlier panel tested at CPRI for short circuit current of 50 KA for one second and similar design and tecnology shall be adopted for fabrication of panel totally enclosed with front opening shutters and proper locking arrengement, 60cm long legs made out of 40mmX40mmX6mm MS angle grouting in PCC 1:2:4 including necessary earth work including removing old existing LT panel:-. (a) MCCB microprocessor based of capacity 320 Amps, 4pole, 415 Volts, 36 KA-01 No (incoming) (b) - do -but MCCB fixed thermal and fixed magneticof 160 Amps, 4pole, 415 Volts, 25 KA - 01 No (outgoing) (c) - do - but MCCB fixed thermal and fixed magneticof 100 Amps, 4pole, 415 Volts, 16 KA - 02 No (outgoing) (d) MCB TPN 63 Amps 4 pole 415 volts 10KA - 02 (outgoing) (e) Digital voltage, Current, frequency, powe factor, power & energy meter-01 No (f) Blank space to accommadate the MCCB upto rating 200 Amps-1 No (g) Aluminium bus bar four strip of rating 800 Amps -01 Set (h) Digital indicator Lamp (RYB) -01 Set

All as per Srl item No.22 above but comprising of following:- (a) MCCB with fixed thermal and fixed magnatic type of capacity 400 Amps, 4pole, 415 Volts, 35 KA-01 No (incoming) (b) - do - but MCCB 200 Amps, 4pole, 415 Volts, 36 KA-01 No (outgoing) (c) - do - but MCCB 160 Amps, 4pole, 415 Volts, 16 KA-02 No (outgoing) (d) - do - but MCCB 63 Amps, 4pole, 415 Volts, 16 KA-01 No (outgoing) (e) Digital voltage, Current, frequency, powe factor, power & energy meter-01 No (f) Blank space to accommadate the MCCB upto rating 200 Amps-1 No (g) Aluminium bus bar four strip of rating 800 Amps -01 Set (h) Indicator Lamp (RYB) -01 Set

Supply, installation, testing and commissioning of LT panel indoor type floor mounted made out of 2 mm thick CRCA sheet dust & vermin proof of IP-54 protection comprising of the following., duly powder coated and pre wired as per standard engineering practice the panel manufacture should have got any of his earlier panel tested at CPRI for short circuit current of 50 KA for one second and similar design and tecnology shall be adopted for fabrication of panel totally enclosed with front opening shutters and proper locking arrengement, 60cm long legs made out of 40X40X6mm MS angle grouting in PCC 1:2:4 including necessary earth work including removing old exisitng LT panel:- (a) MCCB microprocessor based of capacity 400 Amps, 4pole, 415 Volts, 36 KA-01 No (incoming) (b) - do -but MCCB fixed thermal and fixed magneticof 125 Amps, 4pole, 415 Volts, 25 KA - 01 No (outgoing) (c) - do - but MCCB fixed thermal and fixed magneticof 100 Amps, 4pole, 415 Volts, 16 KA - 03 No (outgoing) (d) MCB SPN 32 Amps 4 pole 415 volts 10KA - 06 (outgoing) (e) Digital voltage, Current, frequency, powe factor, power & energy meters-01 No (f) Blank space to accommadate the MCCB upto rating 200 Amps-1 No (g) Aluminium bus bar four strip of rating 800 Amps -01 Set (h) Digital indicator Lamp (RYB) -01 Set

M&L for earthing complete with galvanised steel earth plate electrode 600X600X6 mm thick, burried directly in ground,earth pit not less than 2.25 metre deep below ground level with top edge of earth plate not less than 1.5 meter below ground level, steel earth plate connected with 25 x 4 mm GI strip by means of bolts, nuts, check nuts and washer of galvanised iron or steel as shown in electrical plate No. 5 connected to earth test point all as described in MES schedule part II including excavation earth work concreate pit with 50 mm thick RCC cover in RCC 1:2:4 type B-I duly reinforced with MS bars 6 mm dia @ 150 C/C both ways and pit chamber in PCC 1:2:4 type B-I with 2 Nos suitable lifting handles of 12 mm MS bar and GI protection pipe of suitable size,and watering pipe 20 mm dia with water funnel test point and extra length up to 7.5 meter connected to Panel board all as specified

Supply and laying, testing and commissioning of LT cable XLPE insulated screened and PVC bedded galvanised steel strip or conductor 1.1KV grade cross sectional area 185 Sqmm, 3.5 core laid in trenches/duct/floor or on pole or through pipe all as specified and directed.

All as per Srl item No.27 above but 150 Sqmm, 3.5 core

All as per Srl item No.27 above but 50 Sqmm, 3.5 core

Excavation in trenches in hard/ dence soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr depth for laying of cables/poles or foundation etc and getting out complete all as specified and directed

S&F in replacement galvanized iron pipe 80mm bore light grade fixed to pole with mild steel clamps of required size or laid through wall/under floor/under road/in trenches complete all as specified and directed

All as per Srl item No 31 above but 50mm bore -ditto-

Supplying , installation , testing and commisioning of walk-in- cooler air conditioner at medical store MH Saugor, with minimum 3 star rating of capacity 10,000 BTUH(R22) suitable for working in 230V, SP, 50Hz,airflow 1600 CFM,Air Throw 12 Feet ,Harmetic Reciprocating compressor type complete indoor and outdoor unit alongwith all connected accessories and provided pipe for drainout PVC water pipe upto ground level including installation with copper piping insulation with cable as per site requirement complete all as specified and directed. Make:- Bluestar. Modal:RUAHI-1012(Indoor unit),RUAHOP-1012(Outdoor unit) or equivalent in Voltas/Godrej/Hitachi/Carrier.

m/s mohansingh

shubhanshu traders

M/s VIKAS TRADERS

M/S Sai supplier

Goodluck Enterprises

M/s Prem Associates

dipangashu barick and associates

SHRI RAM ELECTRICALS ENTERPRISES

SHRI HARI CONSTRUCTION

m/s mahendra kumar khare contractor