PROVN OF ONE UTILITY BLOCK CONSISTING OF 02 X WC 02 X BATHROOM 02 X URINAL POTS PROVN OF 02 X TOILET AND SPL REPAIR TO BLDG AT VARIOUS LOCATIONS UNDER AGE BR II AND AGE EM OF GE BENGDUBI

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidated and compacted with clean dry sand complete all as specified and directed.

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Removing excavated material (soil) exc 250m but n exc 500m and depositing where directed complete all as specified and directed.

M&L for hardcore of gauge n.exc. 63 mm, with broken stone or boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2,using 40mm graded crushed stone aggregate as in foundations filling and mass concrete complete all as specified and directed.

M&L for providing pain Cement Concrete (1:2:4) type B1 using 20mm graded crushed stone aggregate as in surface channel and drain complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in copping and filling in back of chowkat the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for Providing, cement concrete 1:2:4 type-B1 using 20mm graded crushed stone aggregate in lintels upto 1.5m clear span, cills, steps;roof padding, seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M&L for Providing precast ce- ment concrete type B1, 1:2:4 using 20mm graded crushed stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and directed.

M&L for RCC(Nominal mix) type B1, 1:2:4 (using 20mm graded crushed stone aggregate) as in foundation,including rafts,footings,foundation beams plinth beams bases for columns etc. complete all as specified and directed.

M&L for R.C.C, Nominal mix of 1:2:4 using 20 mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed.

M&L for R.C.C 1:2:4 (Nominal mix) type B-1using 20 mm graded crushed stone aggregate for Chajjas and like etc. complete all as specified and directed.

M&L for R.C.C 1:2:4 (Nominal mix) type B-1 using 20 mm graded crushed stone aggregate for Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M&L for RCC(Nominal mix) type B1, 1:2:4 (using 20mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts etc. complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded crushed stone aggregate as in Slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded crushed stone aggregate as in chajja , shelves and like etc. complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete design mix M 25 grade using 20 mm graded crushed stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed.

M&L for brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with old size fly ash bricks, straight or curved on plan to any radius as in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L Brickwork with fly ash bricks (old size) in one brick thick honey-comb walling, built in Cement morter 1:4 etc complete all as specified and directed.

M&L for Cutting chases, pinning in brick walls,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc.and making good, cutting not exc 10cm girth complete all as specified and directed.

Making good under cills or over arches, lintels and bressummers. including all pinning in cement mortar 1:6 when necessary complete all as specified and directed.

M&L well burnt old size sub Class ‘B’ bricks, laid in trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical to rough finished surface complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) rough finished surface flat complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, square, rectangular or polygonal in shape complete all as specified and directed.

S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) area not exc. 1.5sqm each, including cutting holes for removing the hold fast,making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, including cutting holes for removing the hold fast, making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heatm moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain/decorative colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement in the frame at site as per specification & drawing. etc complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing complete all as specified Make : Rajshree/Sintex/H2O solution. Note:-The door frame to be fixed to wall using 8 x 100 mm long anchor fasteners.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd.

S&F 100mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 75mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 150mm size aluminium handle cast type complete all as specified and directed.

S&F in repair Harrison rails, mild steel, chromium plated with fixing brackets,stops, rollers etc of 25 mm bore complete all as specified and as directed

S&F tubular towel rail 20mm dia D type brass chrormium plated 600mm long between flanges complete all as specified and directed.

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as secified and as directed

M&L for MS framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Hard drawn steel wire fabric weight n.exc 4 Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and as directed

M&L for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to comman rafters and running rails fixed with angle cleats or other connecting plates conforming to Fe 410 W (Gde E-250) quality-A including welded to rafter,purlin complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 conforming to Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 165mm x 60mm with one or more rebates including necessary , hinges, lock strike plate, fixing lugs etc complete as specified.

M&L for anodised aluminium snap grid (SIZE-605x605MM) frame work for false ceiling complete all as specified and directed.

S&F Hangers 4 mm dia. G.I wire (upto 1200mm length) adjusting level fixed to roof structure complete all as specified and directed.

S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP/ XRW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 (Using 40mm graded crushed stone aggregate) as in sub base of floor/ floor path complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded stone crushed aggregates) as in of flooring etc complete all as specified and directed.

Dismantling of floor, hearth or wall tiling / Paving Blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

S&F 4.0mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

Supply only 4mm plain Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each complete all as specified and directed.

M&L for preparation of old painted wood/wooden surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint (1st grade quality) complete all as specified and directed.

M&L for preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M&L for one coats of synthetic enamel paint on old treated steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for 40mm dia GI pipe Light grade with all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed.

S&F steel water tubes medium grade galvanised with all fittings laid in trenches bore of tube 20 mm complete all as specified and directed.

S&F steel water tubes medium grade galvanised with all fittings laid in trenches bore of tube 25 mm complete all as specified and directed.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and directed.

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and directed.

Taking up or down steel tubing and connections,including cleaning for re?fixing or removal to store bore of pipe 15 mm complete all as specified and as directed

Taking up or down steel tubing and connections,including cleaning for re?fixing or removal to store bore of pipe 20 mm complete all as specified and as directed

Cutting existing steel tubing 15mm bore of pipes for alterations or additions (Each cut measured) complete all as specified and directed .

Dismantling water tanks and removing to store exc 500 ltr but not exc 1000 ltr capacity complete all as specified and as directed

S&F rotational moulded PVC water storage tank 500 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed.

S&F rotational moulded PVC water storage tank 1000 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed.

S&F Bib taps,15mm cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule or for CPVC pipes complete all as specified and directed.

S&F stop valve cast copper alloy screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union of size 20mm dia complete all as specified and directed.

S&F fancy type, chromium plated stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F in repair fancy type, chromium plated stop valve/ angle valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F fancy type with long shank and cup (concealed type) chromium plated stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F in repair fancy type with long shank and cup (concealed type) chromium plated stop valve cast copper allow screw down high pressure with crutch or butterfly handle screwed both end form iron pipe or for union and fixed of size 15mm dia complete all as specified and directed.

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20mm bore and fixed as in repair complete all as specified and directed.

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 25mm bore and fixed as in repair complete all as specified and directed.

S&F ball valves for 20mm bor dia of pipe high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F grating doom 100mm dia of PTMT (minimum weightt 25 gm) for floor trap/nahani trap, complete all as specified and directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms) complete all as specified and directed.

S&F PVC connections pipe ,15mm dia size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 75mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 110mm PVC (SWR) as in drain pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends with rubber ring joints any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC (SWR) vent cowl complete all as specified and directed

S&F 110mm bore PVC (SWR) `P' or 'S' trape complete all as specified and directed.

S&F PVC (SWR) floor trap 75mm dia , plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed.

M&L for plain cement concrete type C-2, 1:3:6 using 40mm graded crushed stone aggregate as in concrete bed including packing under & haunching against sides of bore pipes 150mm dia pipe after the pipe are laid and tested complete all as specified and directed.

M&L for SGSW pipes 150 mm dia grade 'A' laid in trenches and jointed complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approachs, dado/Partitions laid bedded and pointed in any mortar etc complete all as specified and directed

Demolition of cement concrete( un-reinforced) in ground floor and paving n.exc 15 cm thickness( below or above ground level) complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in framed section any position like trusses, rafters, purlins etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dimantling of Asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridges etc complete all as specified anddirected

Dismantling wall and ceiling board( fiber, pulp, insulation, etc.) or insulation board/slab/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for newly plastered surface of wall appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint including 02mm thick wall care putty etc complete all as specified and as directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary fittings and filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, partitions,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make onforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note : (i) Weight of Aluminium sections as per actual or as per IS or as per Manufacturer which over is less, shall only be considered for payment. (ii) Cost of all the items/ accessories required for the entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and particle board shall be measured and paid separately under respective items. (iii) The accessories required for partition as per directions of Engineer-in-charge shall be provided but weight for the same shall not be considered and no extra cost will be paid.

S&F 4 mm thick Non asbestos fiber cement building boards, fixed or laid /inserted to timber /GI /Aluminium frame-work with screws as in ceiling complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab as in skirting/dado over and including 15 mm thick rendering in cement mortar 1:4 fixed & jointed with grey cement slurry mixed with pigment to match the shade of slab including granite ( mirror) polishing complete all as specified and directed.

BLANK

M&L for 75mm thick PCC 1:3:6 type C1 (Using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement.Joints to be given at every 3m interval and corners of buildings and fitted with bituminious mastic or equivalent filler complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregates) as in flooring complete all as specified and directed.

M&L for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in cement mortar 1:3 on fair faces of brick work or concrete surface etc complete all as specified and and as directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm as in dado/skirting etc, set and jointed in neat cement slurry over and including 10mm thick rendering in cement mortar 1:3 and pointed with white or coloured cement to match etc complete all as specified and directed

M&L for pre polished coloures cement concrete chequred tile with grey cement and pigment of approved quality size 300X300X 25mm thick on floors over and including 20 mm thick screed bed cement mortar 1:6 set and jointed in neat cement slurry and pointed with colour to match the tiles complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and fair finished without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately under respective item of this schedule.

M&L for 5mm thick rendering in cement mortar 1:3 over/soffit of chajja/ceiling, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar (1:4) on roof slab concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed. Notes : WPC shall be measured and paid seperately under respective item of this schedule.

M&L for preparing of complete removal of old existing painted surface of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over prepared surfaces complete all as specified and directed.

M&L for complete removal of old existing treatement of internal wall and appying two coat of oil bound distemper over a coat of alkali registant primer over 02mm thick wall care putty complete all as specified and as directed

BLANK

M&L for preparation of new surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation of new undecorated surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for frosted one side sheet glass, 3mm thick, plain ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete all as specified and directed.

M&L for frosted one side sheet glass, 4mm thick, plain ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete all as specified and directed.

BLANK

Supply and laying of CPVC pipes outer diameter 20mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supply and laying of CPVC pipes outer diameter 25mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F CPVC brass elbow 20mm complete all as specified and directed.

S&F CPVC brass Tee 20mm SDR-11 complete all as specified and directed.

S&F bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed.

S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and directed.

S&F 15 mm bore pillar taps fancy type (long neck) cast copper alloy with hot & cold mixture chromium plated screwed down high pressure with or without letter hot or could with long screwed and shanks and fly nuts screwed for iron pipes complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends provided with ovel access door with rubber ring joints any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends provided with access door with rubber ring joints any radius complete all as specified and directed.

S&F in repair Vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), and making good to dismantled/damaged tiling floor complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connection and fixed in position complete all as specified and directed.

S&F Vitreous china urinal, half stall type, white (excluding flushing cistern ,flush pipe and waste pipe) including providing and fixing plugs, bedding urianl against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing only automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed.

S&F Brass chromium plated shower rose 125mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and as directed.

S&F in repair Vitreous china squatting pan 'Orrisa' patterns of size 630mm x 450mm white, (excluding flushing cisterns and flush pipe), including brass chromium plated trap 'P' or 'S' pattern with inlet and outlet integral foot rests, complete all as specified and directed.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level 10 ltr capacity , white, with inlet, ball valve, float and handle including brackets and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed.

S&F Vitreous Cliina wash basin, wliile, flat back, size 550x400mm excluding taps,waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F Vitreous china WHB 550x400mm size white flat back excluding taps,waste, chain and plug and porcelain stopper but including brackets incl cutting or pinning ends of brackets (including waste pipe) incl Waste coupling of PTMT (32 mm dia) (half or full threaded) (Minimum weight 32mm 45gms/40mm-60 gm complete all as specified and directed.

S&F in repair vitreous china WHB 550 x 400 mm size white flat back with brackets including cuttihg or pinning ends of brackets (including waste pipe) and waste cuplihg 32 mm dia brass chromium plated for wash basin etc with long screwed shanks and fly nut flange ends bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton factory made shutter open rebated and prepared to receive glass, gause etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part-I, Sec-08, Clause 8.20(a), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for waterproofing coating by providing and applying Fosroc Brushbond Roof Guard of FOSROC or equivalent of SIKA/STP , a single component High build fibre Reinforced Acrylic waterproofing render for roofing system applied by brush, at three coats at minimum dry film thickness of 1 mm, cured by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane complete all as per manufacturer specification, specified and directed. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2 h

M&L for sand cushioning for protection of underground cable, consolidated and compacted with clean dry sand complete all as specified and directed.

M&L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 10Sqmm 2 core laid in trench/pole/on wall completer all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc as per existing specification complete all as specified and directed.

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed for the followings: -

One light point/ Bell/ one fan point controlled by one switch

One 3 pin socket outlet, 6 Amp on the same board with other switches

One 3 pin socket outlet, 6 Amp independent

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 2.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 2.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed.

M&L for concealed point wiring independent with FRLSH PVC insulated unsheathed multistranded copper conduct or cables 1100 Volts grade of 4.0 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 4.0 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed.

S&F Switch piano, flush type single pole, one way 6 Amp complete all as per specified and directed.

S&F Switch piano, flush type single pole, one way 16 Amp complete all as per specified and directed.

S&F Modular switch 1 way 6A, 1 module complete all as per specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as per specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module, complete all as per specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module, complete all as per specified and directed.

S&F Fan step regulator, 120W - 2 module complete all as per specified and directed.

S&F White cover plate with frame, 8 module complete all as per specified and directed.

S&F Modular Blank plate, 1 module complete all as specified and directed.

S&F Modular type White cover plate with frame 2 module complete all as specified and directed.

S&F Modular type White cover plate with frame 3 module complete all as specified and directed.

S&F Modular type White cover plate with frame 6 module complete all as specified and directed.

S&F modular metal flush box 1/2 module complete all as specified and directed.

S&F in replacement modular metal flush box 3 module complete all as specified and directed.

S&F modular metal flush box 6 module complete all as specified and directed.

S&F modular metal flush box 8 module complete all as specified and directed.

S&F Socket outlet 2 in 1, 6 pin, 6 and 16 amp flush type complete all as per specified and directed.

S&F Socket outlet 2 in 1, 5 pin, 6A complete all as per specified and directed.

S&F Sheet metal enclosure powder coated for MCB DB double door single pole & Neutral 8 way with 200Amp common bus bar at incomming complete all as specified and directed.

S&F Sheet metal enclosure for MCB DB double door 415V Triple pole & Neutral 4 way with common bus bar at incomming end complete all as specified and directed.

S&F Ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as per specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES SSR Part-I connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

Taking down ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

M&L for sub main wiring with 2 run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm alongwith one run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm as earth continuity conductor drawn through and including PVC conduit complete all as specified and directed. Note: For concealed sub-main wiring cutting chases will be included in quoted rate.

Supply and fixing 240V, 10KA 'C' curve single pole miniature circuit breaker (MCB) 6 to 32 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

Supply and fixing 240V, 10KA 'C' curve SPN miniature circuit breaker (MCB) 40 to 63 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN 40 To 100 AMP in the DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement 36W LED Square Type 2' x2' recessed mounted downlighter including suitable driver, cutting of False ceiling as required and all accessories for fixing arrangement complete all as specified and directed.

S&F Decorative wall light fixture, brushed nickel finish, suitable for 9 Watt LED lamp (B22) including 9/10W LED Bulb etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexiblecopper conductor cable with suitable sizecomplete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V,1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing LED tube light batten box type made of CRCA sheet with decorative end caps suitable with ultra bright glass LED tube light 1x 18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/ceiling incl fittings accessories and connecting up with twin core flexible copper conductor cable suitable size complete all as specified and directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounitng arrangements and provision of 1.5 sq mm three core copper dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

S & F for energey efficient exhaust fan of 250mm sweep made of metal body ventil Air-DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as directed by GE.

S & F for energey efficient exhaust fan of 300mm sweep made of metal body ventil Air-DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as directed by GE.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and directed.

Supply & fixing 2 Module socket with sutter 25Amps 240 Volts including Moduler Metal flush box and cover plate complete all as specified and directed.

Supply & fixing 2 Module starter switch 25 Amps 240 Volts including Moduler Metal flush box and cover Plate complete all as specified and directed.

Taking down of old sub main wiring any size and any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

Taking down of Old MCB DB / control box any type any size including MCBs and separating the serviceable MCB DBs and MCBs for reuse at site complete all as specified and directed.

Supply, installation and testing of electric water heater storage vertical type, BEE 5 star rated, 25 ltr capacity 240 volts 50 Hz comprising of high wattage heating element of 2 KW for instant heating, extra Mild steel with Glass lined coated inner tank, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 04 Nos grouting bolts suitably flushed to wall or any other surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/ flexible chord and one No 15 amps 3 pin plug top complete all as specified and as directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 64,566.00 (refer Tender Srl Page No 35). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

PRADIP KUMAR BOSE (BID ID -3395926)

J T ENTERPRISE (BID ID -3395563)

M/S GURUNG CONSTRUCTION (BID ID -3395625)

M/S DUTTA CONSTRUCTION CO (BID ID -3395843)

UNIVERSAL CONSTRUCTION (BID ID -3395667)

KAMALA INDUSTRIES (BID ID -3395731)

D.K ENGINEERING CONSULTANT & CONSTRUCTION (BID ID -3395409)

NEO BUILDERS (BID ID -3395745)