SPECIAL REPAIRS TO KITCHEN BLDG NO P 107 SERVANT QUARTERS P 120 AND P 121 AND ADDITION ALTERATION TO BLDG NO 4B AT CAFVD UNDER GE CENTRAL KIRKEE

Amount

B/R WORKS

Dismantling single layer Mangalore pattern or similar tiles as in roof coverings at any height complete all as specified and as directed.

Roof tiles, Mangalore pattern, interlocking at side joints laid dry single layer or similar tiles as in roof coverings complete all as specified and as directed.

Ridge or hip tiles to suit Mangalore pattern of roofing tiles bedded and jointed in CM (1:6) complete all as specified and as directed.

Second class hardwood clean swan battens at 30cm centre to centre and sectional area exceeding 13 sq.cm and not exceeding 25 sq.cm including dismantling battens for tiles, shingles etc of any size including tiling fillets spaced exc 15cm at any height complete all as specified and directed.

Dismantling at any height timber as in fillets, rails, posts, rafters, purlins etc under 40 sq.cm in section complete all as specified and directed.

Second class hard wood plain fillets, rails, rafters, purlins, square, rectangular in section clean sawn secured with nails, brads, area exc. 13 sq.cm but n.exc. 25 sq.cm complete all as specified and as directed.

All As per Sl Item No. 1.006 above but except rafters, purlins, fillets, etc complete all as specified and as directed.

Galvanised, corrugated mild steel sheeting 0.63 mm thick with two corrugation side lap fixed with L or J type hook with washer and including necessary fittings by using class 8 type sheets, at any height including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering/valley gutters complete all as specified and as directed.

1.00mm thick plain, glavanised, mild steel sheeting as in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade zinc coating 120 including dismantling old plain sheet complete all as specified and as directed.

Dismantling timber in scantling 40 sq.cm and over in section in any position in unframed work and any description complete all as specified and as directed.

Second class hardwood clean swan, as in timber scantlings unframed work fixing at any height with necessary fittings complete all as specified and as directed.

All as per Sl Item No, 1.011 above but except scantlings complete all as specified and directed. NOTE:- Timber scantlings as obtained from Sl Item No. 1.010 shall be reused.

Plain cement concrete, type B1, (1:2:4), using 20mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and as directed.

Preparing surfaces of wood and wood based material,new or old of any description and girth and treated with two coats of creosote oil on new/ old surfaces complete all as specified and as directed.

Pre cast cement concrete solid block masonry with solid blocks of the grade C1 (1:3:6) set in CM (1:6) complete all as specified and as directed.

Rendering 15 mm thick on fair faces of stone/ block masonry surfaces on walls in CM (1:4) finished even and smooth with out using extra cement complete all as specified and as directed.

Rendering 15 mm thick on fair faces of stone/ block masonry surfaces on walls in CM (1:6) finished even and smooth complete all as specified and as directed.

Preparation of newly plastered wall surfaces, applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound emulsion distemper over a coat of primer complete all as specified and as directed.

Preparation of old plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound emulsion distemper complete all as specified and as directed.

Preparation of new or undecorated plastered or unplastered surfaces of wall, and applying two coats of cement base paint (white or tinted) over a coat of alkali reistant primer complete all as specified and as directed.

Preparation of old treated plastered or unplastered wall surfaces of any description including brooming down with steel wire brushing scrapping down smoke soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc and applying two coats of white wash on internal wall surfaces all as specified and as directed.

Preparation of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamal paint complete all as specified and directed.

Preparation of old wood or wood based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Taking down chowkats or frame area n.exc 1.5 sqm each including shutters without taking off shutters from the frame and removing from site.complete all as specified and directed.

Taking down chowkats and frame area exc. 1.5 sqm but n.exc. 4.00 sqm each including shutters, wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

Taking down shutters of any description area exc. 1.00 sqm but n.exc. 2.00 sqm each resecuring, easing, adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed.

Taking down shutters of any description area exc. 1.00 sqm but n.exc. 2.00 sqm each and removing form site complete all as specified and as directed.

Aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with two glass shutters and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.36mm dia apperture, 1.4mm SS wire mesh and fittings etc and making good the jambs and painting with existing surface to match complete all as specified and as directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over 15mm thick cement screed base in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling of existing PCC beds/Granite complete all as specified and as directed.

Rolled Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

100 mm long stainless steel medium weight butt hinges for wooden / PVC / welded to iron frames and door shutters, fixed with bright screwes complete all as specified and as directed.

Aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and directed.

Aluminium anodised handle, oval type, of size 150mm, fixed with screws or welded,complete all as specified and directed.

Pressed steel door frames made out of 1.25 mm thick MS sheet of size 125x60mm for doors, ventilators with double rebates including necessary fixing lugs, hinges, lock strike plate etc, including providing PCC 1:2:4 type B1 using 20mm graded stone aggregate to fill the frame and making good complete all as specified and as directed.

35 mm thick factory made shutters of second class hard wood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated supplied and fitted to chowkat complete all as specified and as directed.

35 mm thick factory made second class hard wood glazed and skelton door shutters, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified and as directed.

Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed.

300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

Preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified and directed.

Gypsum reinforced boards 600x600x8-10mm thick for ceiling hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rawl plugs, level and justers and screws etc, The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm from adjacent center to form 1200x600mm moulds cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instructions and finishing the surface by applying two coats of plastic emulsion paint complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed.

25 mm thick plain cement concrete (1:2:4), type B1, using 20mm graded crushed stone aggregate as in leveling course complete all as specified and directed.

Machine cut Kota stone slab flooring 20-25mm thick over and including 20mm thick cement screed base in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and directed.

Glazed ceramic colour tiles as in vertifical surfaces 450x350x7mm thick with necessary borders etc set and jointed in neat cement slurry and pointed in coloured cement to match over including 10mm thick backing coating in cement mortar (1:4) complete all as specified and as directed.

Stainless steel fancy type curtain rod 25 mm dia including SS brackets, decorative knobs including all necessary fittings such as rawl plug screws complete all as specified and as directed.

Taking up or down existing 15mm dia steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and directed.

Taking up or down existing 20mm dia steel tubing and connections including cleaning for refixing or removal to stores complete all as specified and directed.

15mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor complete all as specified and directed.

20mm bore GI water tubing medium grade galvanised with all fittings and fixed complete to walls and ceilling or laid in floor complete all as specified and directed.

20 mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete fixed in repairs all as specified and directed.

Bib taps long body cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe all as per Prayag Cat Part No :8308 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe all as per Prayag Cat Part No :8310 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

Kitchen sink with drain board overall size 915x460mm, bowl size 410x330x160mm made out of stainless steel 1mm thick kitchen or laboratary sink with plugs, washers and waste including bedding in mortar on to dwarf wall, fixing cantilever brackets and connecting union pipes complete in repairs including taking down the existing sink complete all as specified and as directed.

PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in paving/ plinth protection laid in panels with necessary form work, finished rough surfaces of concrete including provision of construction joints complete all as specified and as directed.

Plain Cement concrete (1:4:8), type D2, using 40mm graded stone aggregate as in sub bases of floors, 100mm thick, complete all as specified and as directed.

25mm thick crushed stone dust/sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Chequered cement concrete tiles 200 x 200 x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement no pigment complete all as specified and directed.

Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-410-W(Gde- E-250) quality-A complete all as specified and as directed.

Rolled mild steel sections as in structural steel main and cross beam, joist, channel, girder etc, Fe-410W fixed in position complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

18-19mm thick prelaminated particle board prelaminated one side, grade 2 quality, interior grade, commercial type including 6 mm thick teak wood lipping, as in cupboards, kitchen cabinet, pelment box and including second class hard wood frame of standard size in similar works complete all as specified and as directed.

75mm long stainless steel hinges complete all as specified and directed.

100mm long hasp and staple, safety type, Aluminium bod with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m depth for foundation in any type of soil and getting out complete all as specified and directed. .

Plain Cement Concrete as in foundation filling and mass concrete (1:4:8), type D-2, using 40 mm graded stone aggregate complete all as specified and as directed.

Reinforced cement concrete, nominal mix, types A1(1:11/2:3) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Reinforced cement concrete, nominal mix, types A1(1:11/2:3) using 20mm graded stone aggregate as in beam, cantilivers, bressummers, lintels over 1.5m span complete all as specified and directed.

Reinforced cement concrete, nominal mix, types A1(1:11/2:3) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. .

TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

As per Sl Item No.1073 above but 5mm and over upto and including 10mm dia as in stirrups spaces and binders complete all as specified and as directed.

Steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) complete all as specified and directed.

Steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

Hard core of guage n.exc. 63mm deposited spread and levelled, laid in layers n.exc. 15cm thick, watered and rammed to a true surface using broken boulders all as specified and as directed.

Moorum / red bajri filling as in floors or pavings, laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Taking down cement or cement lime plaster, any description including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed. .

Rendering 10mm thick plastering in CM(1:6) on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed. .

Rendering 15mm thick wall plastering in CM (1:4) on fair faces of brick work or concrete surfaces including finishing even and smooth without using extra cement complete all as specified and directed.

Rendering 5mm thick plaster in CM(1:3) as in ceiling on fair faces of brick work or concrete surfaces including finishing even and smooth without using extra cement complete all as specified and directed.

Plain cement concret (1:2:4), type B-0, using 12.5 mm graded stone aggregate as in leveling course of floors 25mm thickcomplete all as specified and aas directed.

Plain Cement Concrete (1:4:8), type D-2 using 40mm graded stone aggregate as in sub base to floors, 75mm thick complete all as specified and as directed.

Coloured glossy finish chequered cement concrete tiles of size 300 x 300 x25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Non Skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular area of each tile exc. 0.06 sqm but n.exc. 0.11 sqm in floors etc over 15mm thick screed bed in CM (1:6) set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. .

Factory made solid PVC double moulded door shutter, 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face supplying and fixing in frame at site as per specification & drawings.

100mm Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc.complete all as directed.

Preparation of cement plastered surface new or old of any description and apply two coat Distempering walls with distemper dry, white or tinted over priming coat of chalk whitning on wall complete all as specified and directed.

Prepartation of new or previously un treated wall surfaces of any description and applying three coats white wash complete all as specified and as directed.

Taking down old water proofing treatment of any type and secreed bed and removing the rubbish from the site to a distance exc. 500mtr and n.exc. 1000mtrs and deposited in low lying areas complete all as specified and as directed.

Rendering 15mm thick on existing concrete surfaces of roof in CM (1:4) mixed with water proofing compound @ 3% by weight of cement finishing even and smooth without using extra cement for water proofing treatment over RCC slab by applying oil bound bitumen primer @ 0.25 kg/Sqm and providing and laying 3 mm thick APP modified water proofing memberane of IWLor techno commrcially equivalent weighing not less than 3.00 kg/sqm, reinforced with non woven polyester reinforcement matt weighing not less than 160 gm/Sqm polyester core, having softening point not less than 1500C, longitudinal tensile strength not less than 650 N/ 5 cm, tearing streangth of 180 N / 5 cm, torch application, with a overlap of 100mm at the sides and 150mm at the ends, sealing and applying a coat of solar reflective aluminium paint @ 0.11 Kg/Sqm on membrane surfaces complete including carrying out 24 hrs ponding test over the complete treatment complete all as specified and as directed . Note : Rate for WPC shall be deemed to be included in the quoted rate.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor fixed in repairs complete all as specified and directed.

Vitreous China wash down water closet pan (pedestal pattern), white with P trap 110mm dia, plastic water closet seat, closed pattern with flat bottom, and cover with mild steel chromium plated or aluminised hinging device complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed.

Viterious china wash basin white flat back size 550 x 400 mm excluding taps waste chain and plug and porcelain stopper but incl necessary brackets CP wastes and other fittings complete all as specified and as directed

15 mm dia pillar taps swan neck type, chromium plated cast copper alloy fancy type all asper Cat No PIS-14H Neptune series of Prayag or equivalent make as specified in PS fixed in repairs complete all as specified and as directed.

Stop cock (concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down, screwed both end for iron pipe or brass ferrule with long shank and cup for 15 mm bore of pipe complete all as per Prayag Cat Part No :8318/8320 or techno commercially equivalent makes specified in PS complete fixed in repairs all as specified and as directed.

15 mm dia PVC connection pipe 450 mm long with two nuts fly nuts complete fixed in repairs all as specified and directed.

Rotational moulded, multi layered polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 1000 ltrs capacity complete complete all as specified and as directed.

20mm dia ball brass valves high pressure with polythene float valve & fly nut screwed for iron pipe or for brass ferrule complete all as specified and directed.

110 mm dia PVC (SWR) pipe, type 'B' single socketed in any length with rubber ring joints laid in trenches,floor and wall including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trenches or in floors and wall 75mm bore including taking down old unserviceable pipe any description and any type complete all as specified and as directed.

110mm dia (bore of pipe) PVC bends, type 'B' (any radius), diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified and as directed.

PVC (SWR) bends, type 'B' 75mm dia bore any radius with access door complete fixed in repairs all as specified and as directed.

75mm bore PVC (SWR) vent cowl, type 'B' complete fixed in repairs all as specified and as directed.

PVC (SWR) floor trap, diameter of outlet in 75 mm plain with grating including jointing with solvent cement complete fixed in repairs all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, walls, water staging etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and as directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in, built in in CM (1:4) all as specified and as directed.

Mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed.

Mild steel window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 all as specified and as directed.

PVC floor trap, square type with CP grating with or with out hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm complete all as specified and as directed.

Rotational moulded, multi layered polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs capacity complete complete all as specified and as directed.

E/M WORKS

Taking down copper/aluminium point wiring ( light, fan, socket, power ) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surface of walls, floors, etc complete all as specified and as directed.

Point wiring with two single core PVC insulated multi stranded FRLSH Copper cable of size 1.5 sq.mm drawn in and including PVC casing caping of required size with all fittings and accessories alongwith green colour FRLSH Copper conductor cable of size 1.5 sq.mm as earth lead and connected to earth dolly including PVC switch board and accesories of required size and making good to disturbed surfaces complete all as specified and as directe for one light point controlled by one switch. NOTE:-- One phase, one neutral and one earth of copper wire will measured as one point.

All as per Sl Item No 2.002 above but for one fan/Exhaust fanpoint with cables 1.5 sq.mm size complete all as specified and as directed.

All as per Sl Item No 2.002 for one three pin 5 Amps socket outlet point with cables 1.5 sq.mm size on independent board complete all as specified and as directed.

All as per Sl Item No 2.002 for One three pin 5 Amp socket outlet point ,with cables 1.5 sqmm size on same board complete all as specified and as directed.

All as per item No 2.002 but FRLSH copper stranded cable of size 2.5 sq mm for 3/6 pin socket outlet 15 amp on one independent board. alongwith all fitting and accessories complete all as specified and as directed.

5 Amp switch piano flush type single pole one way complete all as specified and as directed.

Lamp holder of PVC/ Polycarbonate type with back plate complete all as specified and as directed.

Socket flush type 6 amps, 5 pin, 230v complete all as specified and as directed.

Switch socket combination multipurpose 2-in-1 flush type 3 pin 16 Amps and 3 pin 6 Amps complete all as specified and as directed., 230v

Ceiling rose surface Bakelite three terminal all incl dismentling taking down unsv one complete all as specified and as directed.

Flush type electronic fan regulator with 5 step type, 240 Volts AC, 50 Hz complete all as specified and as directed.

Sheet metal Enclosure SPN 8 way (MCB DB) Double door, 240 Volts AC complete all as specified and as directed. Make Schneider /ABB/Legrand

MCB, SPN (double pole) 40 Amps, 240 Volts, 10 KA ‘’C” curve complete all as specified and as directed. Make:- Schneider / Legrand/ABB

MCB, Single Pole, 5 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve complete all as specified and as directed. MAKE- Schneider / Legrand/ABB

LED tube light fitting industrial box type batten with precoated CRCA body, suitable for and including 1 x 20 Watt 4 feet long tube with polycarbonate diffuser, LED lamp efficiancy -110 Lum/W ,THD<15% with operating voltage range 100-300V, driver efficency >85%, surge voltage with stand 2.5KV, power factor >0.9 including connecting complete all as per Crompton Cat no-IGP161LT8-16 & LT8-20-865 are techno commercially equivalent all as specified and as directed.

LED lamp 9 watt, CDL, E-27 230V, PF-0.95 (min) complete all as specified and as directed. Make- CG /Havells/Bajaj/ Philips

LED building security light 35 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fasteners all as per Shakti, Cat Part No SZPSLMM015 or techno commercially equivalent in Philips/Bajaj/CG complete all as specified and as directed.

Energy saving ceiling fans, 230 Volts, 26 Watts, single pole, 1200 mm sweep, high speed of approved colour with remote control and two years warranty certificate from the manufacturers, with latest BEE five star rating and BLDC technology all as per Havells Model No :- Efficiencia Neo (BLDC 26W) or techno commercially equivalent models specified in PS complete with down rod and GI hook with welding work, wire connections from ceiling rose to ceiling fans, with complete accessories including writing of MES No with unit name on ceiling fans using approved stencil with synthetic enamal paint complete all as specified and as directed. Note - Old un serviceable ceiling fan shall be deposited to MES store.

Exhaust fan metal body, AC Single phase, 230 Volts of size 450 mm sweep with blades and frame and louvers including making of suitable hole in brick / stone wall for fixing of exhust fan complete all as specified and as directed. Make- Havells/Almonard/ Crompton Greves NOTE: - Old un serviceable ceiling fan shall be deposited to MES store.

Earthing complete with galvanised steel pipe electrode, 40 mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion complete all as specified and as directed.

PVC insulated, PVC sheathed twin flat core 1100 volts grade, 10 sq.mm aluminium stranded conductor (incl PVC conduit/wire guard where required) complete all as specified and as directed.

LED light fitting 72 Watts road lighting luminaire having system lumen of >110 lumen/watt , IP 65/66 protaction with high power LED with PDC aluminium body& secondary optical lens for better light distribution Make-crompton Greaves/bajaj/Philips complete all as specified and directed.

LED batten with 12 Watt LED 2' feet light source in intergral module with polycarbonate / acrylic diffuser more than 85% efficiency of light LED lamp efficay-110 Lum/W, THD<15% with operating voltage range 100-300V, driver efficency >85%, surge voltage withstand 2.5KV, power factor >0.9 including connecting complete all as specified and directed. Make- Bajaj,havells,wipro/CG/Phillips.

Exhaust fan 300 mm sweep with louvreAC ,single phase 230 volts with complete all as specified and directed.

XLPE insulated, screened,PVC bedded, galvanized steel strip or wire armoured,electric power cables (heavy duty)1100 volts grade with stranded aluminium conductor of size 10 sq.mm 4 core complete all as specified and as directed.

Sub main wiring with two single core PVC insulated multi stranded FRLSH copper conductor cable of size 4.0 sq.mm drawn through in and including PVC casing caping of size with all accesories and one single core green colour FRLSH Copper conductor cable of size 4 sq.mm as earth wire and connected to earth dolly including dismantling unserviceable sub main wiring and making good to disturbed surfaces all as specified and directed. NOTE:-Two runs of cable with one run of earth wire and one run of casing capping will be measured as one unit (RM)

Sheet metal enclosure SPN 4 way (MCB DB) Double door, 240 Volts AC of Make Schneider /ABB/Legrand all as specified and directed.

MCB DB double door 4 way TPN DB with 200 Amps rated bus bar 240 volts all as specified and directed.

MCB TPN 40 Amps, 415 volt 10 KA all as specified and directed.

LED building security light 15 watt, 230 Volts complete with all accessories and including connecting up to ceiling rose with 0.5 sq.mm three core copper flexible conductor cable, One GI medium grade 20mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as per Shakti, Cat Part No SZPSLMM015 or techno commercially equivalent in Philips/Bajaj/CG all as specified and directed.

XLPE insulated, galvanised steel strip or wire armoured and PVC bedded, heavy duty, LT cable 16 sq.mm, 2 core, 1100 volts grade with multi stranded aluminium conductor, including cable glands, cable lugs etc., to suit the cable size, laid in trenches, or fixed along with the poles, bare or through GI pipe, laid under floors / road etc., fixed / concealed in walls / encased in GI pipe etc., jointing and testing complete all as specified and as directed.

Excavation in trenches n.exc. 1.5m wide and n.exc. 1.5m in depth for laying of pipe and getting out in soft loose soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in soft disintegrated rock complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete all as specified and as directed.

Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

Fine stone dust for cousioning of UG cable/ at cable trenches complete all as specified and as directed.

Bricks, sub class 'B' of old size 230 mm x 115 mm x 75 mm laid in trenches for cable protection all as specified and directed.

25mm bore medium grade galvanised pipe with all fittings such as tee bends, union, elbow, reducer, laid in trenches / fixed to walls / floors, ceilings all as specified and as directed.

20mm bore medium grade galvanised pipe with all fittings such as tee bends, union, elbow, reducer, laid in trenches / fixed to walls / floors, ceilings all as specified and as directed.

Gun metal gate or globe valves 40 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Gun metal gate or globe valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Gun metal gate or globe valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed