SPECIAL REPAIRS TO P45 CENTRAL STORE KLP SEC AT CQA EE TECH AREA AUNDH CAMP PUNE UNDER GE MH AND RH KHADKI

Amount

Taking down chowkats and frame exc 1.5 sqm and n. exc 4.0 sqm incl shutter without taking off shutters from frame and removing from site specified and directed

Taking down chowkats and frame n exc 1.5 sqm incl shutter without taking off shutters from frame and removing from site specified and directed

Dismantling structural steel work including doors, gates but excluding framed truss etc. all as specified.

Demolition of Brickwork, solid block or stone/ boulder masonry, built in cement/ lime mortar including all quoins, arches, pillars, etc, and including ashlar facings, dressed stonework and precast concrete articles

Dismantling water tanks of any discription or capacity 1000 ltrs and removing to store all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for PCC(1:3:6) type C1 using 20 mm graded stone aggregate as in coping, filling of chowkat incl necessary form work and finished even and smooth without using extra cement all as specified and directed.

M&L for Pre-cast cement concrete block masonry type C1 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in CM 1:6, complete all as specified.

Taking down cement/ cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L for Rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 with sagol finished even surface all as specified and directed by Engr-in-Charge

M&L for Rendering 10mm thick, on fair faces of brick work or concrete surfaces of ceiling in CM 1:4 with finished even surface all as specified and directed by Engr-in-Charge

M&L for Rendering 15mm thick, on fair faces on stone masonry surfaces or surfaces walls in CM 1:4 incldg WPC finished even & smooth all as specified and directed by Engr-in-Charge Note:- WPC shall be measured seperately

M&L for providing water proofing plaster at the junction of wall and slab at chajjas, lintels etc, of average thickness 20mm in CM (1:3) with WPC, finished even and smooth without using extra cement all as specified and directed. Note:- WPC shall be measured seperately

Supply only Integral waterproofing compound

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

All as per item No 17 above, but in riser, step, skriting, dados and piller overs 10mm thick plastering in CM 1:4 all as specified.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.50mm graded aggregate) finished even and fair in levelling course for laying tiles over it as directed

M&L for cement concrete type C1 1:3:6 (20mm graded aggregate) 75 mm thick as in sub-floors, sub-bases, floors and paving, etc all as specified and directed

M&L for coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over cement screed 15 mm thick in CM 1:6 complete all as specified and directed

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles laid over cement plaster 10 mm thick in CM 1:4 complete all as specified and directed

M&L coloured joint free Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over cement screed 15mm thick in CM 1:6 complete all as specified

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and pointed in white or coloured cement to match the shade of the tiles laid over cement screed 15 mm thick in CM 1:6 complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, window cill and other similar situations all as specified.

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F of Factory Made Solid PVC Moulded Door Shutter,With Particle Board Core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified

S&F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated Anodised aluminium three track window and ventilator shutters, slinding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings all as specified

Supply only 5.50mm thick Sheet glass, ordinary quality in square n exc 0.5 sq.m in each pane

Supply only 5mm thick Sheet glass, obscured or frosted square in exc 0.5 sq.m in each pane

S & F Pressed steel door frame for doors with one or more rebate incl necessary fixing lugs, hinges lock strike plate, etc complete as specified size 105 x 60mm

M & L for 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated as specified

M & L for Aluminium anodised barrel tower bolts of stove enamelled blackwith bright bolt and fixed 200mm long all as specified and directed.

S&F butt hinges medium weight colled rolled mild steel 100 mm and fixed all as spd & directed by Engr-in-Charge

S &F 0f Aluminium alloy, anodised sliding door bolt 300 mm long, plate type,stove enamelled black with bright bolt not less than 12 mm dia with and incld mild steel min of 6 bolts and nuts, 4 on bolt plate and 2 on stapleplate fixed/weldedto door shutter/frame all as specified

M & L for Aluminium handles, cast type, anodised handles stove enamelled blackfor doors 150 mm long all as specified and directed by Engr-in-charge.

S&F in repairs Tubular towel rail Brass chromium plated , 20mm dia, D type, 60cm long between flanges all as specified

S&F in repairs of 15mm dia fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in repairs of Vitreous China wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets and pinning in end of bracket or erecting stand but exclusive of fixing of supply and waste pipe

S&F in repairs of Vitreous China Urinal, full stall type, white complete including CP waste coupling, CP spreader etc all as specified.

S&F in repairs of fancy type Bib taps of 15mm dia of pipe, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

M&L for 100mm dia Cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor.

S&F in repairs Health faucet brass chromium plated ISI Marked,including connecting decorative pipe and all accessories required for fixing of 15 mm bore of pipe all as specified and directed.

S&F in repairs CP 15mm bore 2 way bib cock Make Jaquar catloag no.CON 041 KN etc complete.

Taking down drain pipes (any size or pattern), including all fittings, T, bends,etc., including cleaning or refixing (measured overall as fixed along the centre line over fitting and accessories)

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm dai PVC (SWR) bends any radius

S&F 75mm dai PVC (SWR) bends any radius

S & F in repairs stopvalves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15 mm dia all asspecified and directed.

Taking up or down steel tubing 20 mm dia and connection including cleaning for refixing for following bore of pipe, complete all as specified

Taking up or down steel tubing 15 mm dia and connection including cleaning for refixing and removing to store for following bore of pipe, complete all as specified

M&L for tube medium grade 20 mm dia, galvanized with all fittings fixed complete to wall, ceiling or laid in floors etc. for following dia of pipe, complete all as specified

Refixing old steel tubing and connection of 20 mm diain new or old position (walls, ceiling ,floor etc

M&L for tube medium grade 15 mm dia, galvanized with all fittings fixed complete to wall, ceiling or laid in floors including cutting chases for concealed water tubing etc. for following dia of pipe, complete all as specified

Refixing old steel tubing and connection of 15 mm diain new or old position (walls, ceiling ,floor etc

S&F in repairs, gun metal globe or gate valves 20 mm dia ,with iron wheel head,screwed both ends for iron pipes including cutting chases for concealed water tubing

S & F Rotational moulded polyethylene water storage tanks ( cylindercal veritcal with closed top) hoisted and fixed inposition 1000 ltrs capacity all as specified

S&F in repairs ball brass valve 20 mm dia high pressure with poly-thine float and fly nut for following bore of pipe, complete all as specified

Preparation of new steel surfaces over 10cm in width or girth and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified.

M&L painting to wooden surfaces of any description over 10 cm width or girth incld prepration of new or untreated surface and applying two coat of synthetic enamel paint over one coat of pink primer all as specified

M &L for preperation of new surfaces and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over 3mm thick wall care putty finished even and smooth complete all as specified.

M&L Complete removal of existing treatment & applying two coats of oil bound distemper of approved colour and pattern over a coat of primer over 3mm thick wall care putty finished even and smooth.

Preparation of new plastered surfaces on ceiling and applying two coats of white wash over 3mm thick wall care putty finished even and smooth complete all as specified.

M&L for Complete removal of existing treatment on ceiling & applying applying two coats of white wash over 3mm thick wall care putty finished even and smooth complete all as specified.

S&F of powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L snap grid PVC coated gypsum ceiling with 19mm thick semi - perforated edge 60x60cm in ceiling board including over GI grid prelude XL 24 mm grid main runner height 37mm and secondary runner height 30mm including 2.6mm/2.8mm GI wire suspenders of suitable length as per manufacturers instructions all as specified and directed .

Taking down Wall panelling and similar work all as specified and directed

S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge

Removing of old water proofing treatment and cleaning the surface of slab and cleaning with wire brush, removing dust,foreign materials and removing the rubbish off the site to a distance n.exc 100m all as directedby Engr - in - Charge.

M & L for PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate ) on roof top for maintaining of slope coving,benching etc all as specified and directed.

M&L for Rendering 10 mm thick on concrete surfaces of roof in cement plaster in 1:3 CM mixed with WPC @ 3% by weight of cement finishing even and smooth to receive water proofing treatment complete without using extra cement all as specified and directed by Engr-in-Charge. Note :- WPC shall be measured and paid seperately.

M & L for cleaning the plaster /concrete surfaces with wire brushes and applying water proofing treatment ,one coat of bituminious primer @ 0.25 kg per sqm and providing 3 mm APP modified water proofing Membrane weight 3.5 to 4.0 kg /sqm by torch application method including painting entire roof surfaces with one coats of bitumastic aluminous paint

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed.

M&L for point wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid medium grade PVC conduit and accessories concealed in walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 81 above for one 3 pin 5 Amps socket on same board control with other switches on same board

All as per item No 81 above for one 3 pin 5 Amps socket on independent board.

All as per item No 81 above but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket on independent board complete all as specified and directed.

All as per item No 81 above but with 4 Sqmm PVC insulated multistranded copper conductor with 4 sqmm cable as earth continuity conductor for Power Socket/AC/Geysers on independent board complete all as specified and directed.

Supply and fix modular switch 1 way 6A 1 module complete all as specified and directed.

Supply and fix modular bell push 6A 1 module complete all as specified and directed.

Supply and fix modular socket 6A 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix modular socket 16A 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix modular switch 1way 16A 1 module complete all as specified and directed.

Supply and fix Modular fan regulator

Supply and fix electric bell Ding Dong, AC 230 volts complete all as specified and directed.

Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed.

Supply & fix LED fitting for Bldg security, 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant complete with IP - 66 protection complete. including connecting with 1.5 sq mm 3 core flexible copper cable from fitting connector to ceiling rose and fix on wall with GI bracket made of 32/40 mm light grade GI pipe of 1 mtr length fixed with MS clamps & nut bolts of suitable size complete all as specified and directed .

Taking down old unserviceable Tube light fitting of any type and S & F wall/ceiling mounted LED tube light fitting aluminium body , Energy efficient high quality invertor batten having Lithium ion battery of 3.7V, 19 WH for backup upto 2Hrs with high power brightness having BIS certification, LED fitting should be LM 80 certified with system efficacy greater than 100 lumens/watt, including LED tube 20/22 watt having colour temperature 6500 K (4 feets long) , PF> 0.95, THD less 10%, with IP20 protection having open and short circuit protection, having input voltage range 90V to 300V connecting with three core flexible copper wire from connector to ceiling rose/angle holder as per existing site requirement as directed by Engr-in-charge. Make : Jaquar/Halonix/Philips . Note :- The rates are inclusive of cost of ceiling rose -01 nos and square box-02 nos including suitable size of clamps and screws etc.

Supply and fixing LED Light fitting mirror type with high output diffuser 2 feet , 1 X 10 watt 220 V AC decorative type with driver holder and LED lamp, Alluminium housing, including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down old unsv Recess mounting fitting of any type from any height and S & F high quality Energy efficient Recess/Surface mounting 2'x2' recessed inverter fitting, CRCA powder coated steel housing with high power brightness having BIS certification , fitting should be LM 80 certified with system efficacy greater than and equal to 100 lumens/watt, having Lithium ion battery of cap 3.7V, 19 WH for backup upto 2 hrs having operating voltage range 90volts to 300volts having colour temperature 5700K, PF> 0.95, THD less 10%, with IP20 protection having open and short circuit protection, connecting with three core flexible copper wire from connector to ceiling rose as per site requirement as directed by Engr-in-charge. Make : Jaquar/Halonix/Philips . Note :- The rates are inclusive of civil work(minor plastering, painting, false ceiling repair etc) wherever required for fixing the fittings to the roofs/ceilings.

Taking down old unsv wall bracket light fitting of any type & S & F wall mounted high quality indoor wall bracket light cylinderical/oval shape aesthetically designed fitting in wooden housing , glass and B22/E27 holder complete including inverter LED bulb B-22 cap with opal diffuser, IP-20 and inbuilt battery backup (LED INVERTER LIGHT 10W B22 CW IP) 10 watts including necessary electric connection with PVC insulated multistranded copper cable of size 1.5 sqmm 3 core from ceiling rose to fitting terminal complete all as specified and directed.

Taking down unsv submain wiring and M&L for submain wiring in PVC conduit with two runs of 10 sq mm and one runs of 10 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid conduit medium grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports etc all as specified and directed. Note: Two runs of 10 sq mm and one runs of 10 sqmm cable along with conduit shall be measured as one length.

S & F sheet metal enclosures in repair double door distribution board factory made duly painted 8 way SPN 240 volts with 200 amps rated copper bus bar , concealed in wall and suitable for fixing MCB /Isolators all as specified and directed.

S & F sheet metal enclosures in repair double door distribution board factory made duly painted 12 way SPN 240 volts with 200 amps rated copper bus bar, concealed in wall and suitable for fixing MCB /Isolators all as specified and directed.

Taking down unsv metal box of any type and S & F sheet metal enclosures double door type distribution board factory made duly painted 4way TPN and neutral 440 v with 200 amps rated bus bar concealed in wall , suitable for fixing MCB /Isolators all as specified and as directed by Engr-in-charge.

S & F MCB SP of capacity 5A - 32A B' curve all as specified and directed.

S&F MCB, SPN (DP) 32 amps, 240 Volts, 10 KA ‘’C” curve all as specified and directed.

As per item no 104 but SPN 50 Amps. Make L &T /Legrand/Hager

S & F in repair MCCB of capacity 63 Amps, 4 pole, Breaking capacity 16 KA, 415 V adjustable type all as specified Make: L &T /Legrand/standard.

M&L for earthing with 600x600x6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including G.I. wire of size 4 mm dia by means of bolts,nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 & RCC Chamer cover of size 540x540x100 mm made with 1:2:4 Type B1 using 6 mm round MS bar & 8 mm MS bar for handle , 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed.

M & L for taking down Exhaust fan steel body, celing cable end, dismantling blades and removing fan and blades to store painting of exhaust fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc after complete repairing of builidng, fixing exhaust fan on existing position all as specified and directed. (for Toilets)

M & L for taking down ceiling fan, celing cable end, dismantling blades and removing fan and blades to store painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc after complete repairing of builidng hanging ceiling fan on existing position all as specified and directed. .

M & L for Fan hook , clamps hold fast with all necessary materials for hanging fan all as specified and directed.

M & L for taking down Wall Mounting fan, celing cable end, dismantling blades and removing fan and blades to store complete, Cleaning all dust, etc after complete repairing of builidng, fixing wall fan on existing position with new hanging clamps complete all as specified and directed.

Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with 20/32 Amp DP MCB all as specified and directed ( For AC)

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation of poles stays laying of electric cables, pipes etc and getting out in soft/loose soil complete all as specified and directed.

All as per item no 114 but in hard/dense soil.

Removing excavated material soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

Returning, filling in, including spreading, levelling watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and directed.

M & L for riddled earth for cushioning to under ground electric cable including spreading , levelling and hand punning complete all as directed. Note - Punned thickness shall only be measured & paid .

M& L for road cutting / foot path and making good with PCC 1:3:6 TYPE C-2 ( using 40 mm graded stone aggregate ) of 150 mm

Supply and laying un-reinforced precast concrete cable cover LV, Type I, flat, size 250mm x 150mm x 40mm for Under ground cable all as specified and directed.

Supply and laying GI tubes light grade, galvanized, 40 mm bore in repair ,laid in trenches or under floor or fixed with poles/walls for protection of electric cable all as directed

V.R.PRAJAPATI AND CO. (BID ID -3078487)

M/S J J ENTERPRISES (BID ID -3078304)

shree ram enterprises (BID ID -3094878)

A.S.ENTERPRISES (BID ID -3095576)

R K Construction (BID ID -3074139)