COMPLETION OF INCOMPLETE WORKS FOR RAISING AND STRENGTHENING OF EXISTING COMPOUND WALL AND PROVN OF NEW WALL AT SURVEY NO 234 AT NIRIKSHAN VIHAR RESIDENTIAL COMPLEX AT CQA A KIRKEE

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/dense soil complete.

All as per item no 1 above but in soft/disintegrated rock complete all as specified and directed.

All as per item No 1 above but in hard rock by chiselling complete all as specified and directed.

M&L for plain cement concrete (1:4:8), type D-2 (using 40 mm graded stone aggregates) as in foundations, filling and mass concrete all as specified and directed..

Use and waste of formwork to sides of concrete foundations, column footings, plinth beams, and similar works, vertical or to batter for rough finished flat surfaces of concrete complete

Use and waste of formwork to sides of pillars, posts, struts, piers, columns of square, rectangular or polygonal, rough finished surfaces of concrete complete

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete

M&L for mild steel TMT bars 5 mm dia and over, upto and including 10 mm dia as in stirrups, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil complete all as specified & direceted.

Removing excavated material exc 500 mtr and up to 1.50 Kmtrs and depositing out side MD land.

Demolition of masonry wall, built in cement mortar including all quoins, pillars etc.

M&L for solid block masonry with precast cement concrete block 1:5:8 type C-5 wall exceeding 10cm in width using graded stone aggregate, and setting in cement mortar (1:6).

All as per item No 12 above, but except PCC blocks .

S&F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work

S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. Notes : Each line of wire to be measured separately

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of concrete surfaces, finishing the surface even and fair with out using extra cement complete.

Preparation of plastered surfaces of walls and applying two coats of cement base paint.

Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer.

Rough excavation n exc 1.5 m deep and getting out in soft/loose soil complete all as specified.

Demolition of re-inforced cement concrete of any description and in any position.

M&L for providing reinforced cement concrete, grade (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in foundations including rafts, column footings, plinth beams, etc complete

M&L for providing reinforced cement concrete, grade (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in columns, ,pillars, piers, posts and struts etc complete

M&L for providing reinforced cement concrete, grade (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in lintel beam/band over 1.5 mtr span

Use and waste of formwork to edges of concrete flats, RCC band of wall horizontal and similar work rough finished surface of concrete exc 5cm but n exc 10 cm width including extra form work for filleting to produce bullnosed angle, exc 25mm width.

M&L for mild steel TMT bars 8 mm dia, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete

Preparation of new steel surfaces of small articles such as fasteners, ends of roof trusses, gates, ends of posts, etc and treating with two coats of black Japan paint over a coat red oxide primer.

S & F concertina coil with galvanised MS, 0.5mm thick punched tape (as per IS 1730) reinforced with galvanised MS wire of 2.5mm dia (as per IS 4454), 610 mm high,with minimum no of loop 8 per meter including necessary fastener, clips, etc to connect with angle or brackets all as specified and directed. Note :- 1) Cocertina coil shall be tied to the angle iron with barbed wire inside at every third loop. 2) Barbed wire shall be measured and paid separately.

Supply only mild steel galvanised chain link fencing of mesh size 75mmx75mm using 4mm dia MS wire.

Fixing only chain link fencing including line wires of any dia, any mesh size and type to any types of starndards, rails, straining bolts etc including provision of binding wire, 6 mm dia MS bar complete.

GURBAX AND COMPANY