GE(P)AF/GUR-07/2021-22 CERTAIN REPAIR TO PLASTERING, FLOORING, ROLLING SHUTTER AND JOINERY INCLUDING CONNECTED B R WORKS IN MES INSTALLATIONS AT AF STN GURGAON UNDER GE (P) AF GURGAON

Amount

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises completed all as specified and as directed by Engr-in-Charge.

Demolition of cement concrete of any description as in ground floor and paving exc 15 cm thickness(below or above ground level) all as directed by Engr in charge.

M&L for pre cast Kerb stone with plain fair faces 300x150x300 mm depth of PCC 1:1 ½ :3 of shape as approved incl all excavation, embedding in ground and removing surplus spoil upto 50 Mtr distance completed all as specified and as directed by Engr-in-Charge.

M&L for machine cut broken stone of gauge not exc 63mm as in hard core N EXC 150mm thick spread and levelled including watering & ramming all as directed by Engr-in-Charge.

M&L for providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for 60mm thick Machine pressed pre casted pressed cement concrete inter locking paver blocks glazed coloured up to 6mm on the top in any shape and size, strength not less than M-35 including clean dry fine sand grouting completed all as specified and as directed by Engr-in-Charge.

M&L for sand filling under floors or in foundations incliding watering & consolidation complete all as specified and directed.

M&L for Chequered cement concrete tiles 300x300x20mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:4 all as specified and as directed by Engr-in-charge.

M&L for 18-20 mm thick machine cut and pre-polished Kota stone slab flooring over 15mm thick in CM 1:6 cement screed bed and jointed with gray cement slurry mix with pigment to match the shade of slab including final polishing complete all as directed by Engr-in-Charge.

M&L joint free glazed ceramic tiles in vertical surfaces of size exc .05 sqm and n.exc 0.18 sqm and 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Cutting and grinding mirror polishing old kota stone flooring including applying cement slurry to fill the existing joints completed all as specified and as directed by Engr-in-Charge.

Taking out the existing paver blocks of any size and set and jointed again in the same position after cleaning of grass and other vegitation etc all as directed and specified by engr in charge.

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MOD land, complete all as specified and directed.

M&L for PCC (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope (max up to avg 50mm thick) and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick cement plaster on brick work or over roof surface in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 0.50% by weight of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L water proofing treatment of roof consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.00 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Supply only water proofing liquid compoundcomplete all as specified and directed by Engr-in-Charge. :Make : DR. FIXIT PIDE PROOF LW, CICO, FOSROC.

M&L for Appling one coat Bitumen water proofing aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge. Make : PLASCON/PLASCON or equalant

Dismantling of brick work built in cement mortar including all quions, arches, pillars, etc.completed all as specified and as directed by Engr-in-Charge.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 completed all as specified and as directed by Engr-in-Charge.

All as per srl item No. 21 here in before but except bricks Note:- Serviceable bricks obatined from srl item No. 20 shall be re-used after cleaning etc complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster, any description on brick walls or on concrete surfaces including racking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed.

M&L for for rendering 15mm thick in CM (1:4) on brick work or concrete surfaces other than fair face of brick work, finished fair & even w/o using extra cement in patches with water proofing compound(water proofing compound paid sepratelly in item) all as specified and directed by Engr-in-Charge.

M&L for rendering 10mm thick in cement motar 1:4 on ceiling like chhaja, roof projection facia etc on concrete surfaces, finished fair & even without using extra cement completed all as specified and as directed by Engr-in-Charge.

M&L for Preparing Newly Plastered Surfaces of WALLS and applying two coats of exterior weather paint over a Coat of APPROVED PRIMER, complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparing New Plastered Surfaces of WALLS and applying TWO COATS of DISTEMPER OIL EMULSION (OIL BOUND WASHABLE DISTEMPER) with primer over a Coat of CHALK WHITING, complete all as specified and as directed. by Engineer-in-Charge.

M&L for Preparing Newly Plastered Surfaces of WALLS and applying THREE COATS of WHITE WASHING, complete all as specified and as directed. by Engineer-in-Charge.

M&L for Complete removal of existing treatment upto plastered surfaces including preparation of surfaces of walls and cornices and applying one coat primer, two coat of acrylic emulsion paint over two coat of JK/birla putty upto 4th storey including necessary scaffolding all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine complete all as specified, removal of nails etc & filling cracks/hole with putty, applying wall care putty upto 1mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed by Engineer-in-Charge.

M&L for Preparation of old decorated surfaces of ceilling, and applyig two coat of white wash on ceilling completed all as specified and as directed by Engr-in-Charge.

M&L for Preparation of old painted steel surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engineer-in-Charge.

Dismantling mild steel work of any description not otherwise provided completed all as specified and as directed by Engr-in-Charge.

M&L for Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A with riveted bolt or welded etc as in duct cover & similar work completed all as specified and directed by Engr-in-Charge.

M&L for rolled section as tubular sections as in vertical steel columns with flange plates, caps, bases, base plates, splices angle brackets, cleats, holding down bolts and nuts and other section complete of Fe 410 W E-250 grade including all welding etc, complete all as specified and directed by Engr-in-Charge.

S&F Framed work such as Gate,grills etc with ends of bars shoulders and / or riveted or forged into spikes, framed guard bars barred iron door ladders, framed balusters walls way, railings, frame work of water tank and similar work confirming to Fe 410-O or 310-O all as specified and directed by Engr-in-Charge.

S&F for MS angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement.

S&F 1mm mild steel, plain black sheet hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required and directed.

M&L for Preparation of new steel surface exc 10 cm width/girth one coat red oxide primer and two coat synthetic enamal paint completed all as specified and as directed by Engr-in-Charge.

S&F in repair Galvanized 2 stand Steel Barbed wire 2.24mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge.

S&F in repair 950/650/450 mm dia (as directed by Engr-in-Charge) concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed by Engineer–in-Charge.

Dismantling of plain or corrugated steel sheeting / AC sheeting any gauge thickness inculing nanital or similar pattern roor coverings all as specified and directed by Engr-in-Charge.

S&F 0.5 mm thick pre coated thick galvalume aluminium zink coated GI based corrougated steel sheeting of any colour having tansile strength of 550 MPA as in roof covering/glading to wall fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

M&L for Chain link MS galvanised fencing, any size or type including line wires, any mesh, standartds rails, straining bolts etc including provision of binding wire all as specified and directed by Engr-in-Charge.

S&F 2 mm thick fibre glass reinforced translucent corrugated/ plain sheeting with two corrugations side lap fixed with L type or J-type or cranked hook botls and washer in roof, wall and similar work etc all as specified and directed by Engr-in-Charge.

M&L for expanded metal not exc four kg per sqm, cut to length, bent to shape required and tying with and including annealed muild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position completed all as specified and as directed by Engr-in-Charge.

M&L for 100mm thick Cement concrete type B2 1:2:4 (40mm graded stone aggregate) as in path finished even and smooth with broom finished without using extra cement, laid in panels not exceeding 2 sqm each panel and joints shall be filled with sealing compound Gde-A, complete all as directed by Engr-in-charge.

M&L for PCC 1:2:4 type B1 using (20mm graded stone aggregate as in cills, copings, small plates incl weathering slightly rounded or chamfered angles and throating including necessary form work complete all as directed by Engr-in-Charge.

Taking down steel rolling shutter and refixing with or with out ball bearing including to cover side guide rail and greasing of MS spring and side guide and make functional including complete overhaling size exc 10 sqm but nexc 40 sqm as entire satisfication of Engr-in-Charge. (Note : Supply of material to be measured seperately)

S&F of MS pipe medium grade of dia upto 40 mm including cutting and fixing, drilling, welding for rolling shutter all as directed by Engr-in-Charge.

S&F spring of high carbon spring 30mm dia drilling, welding for rolling shutter all as directed by Engri-in-Charge.

S&F in repair of mild steel rolling shutter strips made out of 1.25mm MS sheet including and reavting including one coat of primer and two coat of synthetic enmail paint all as directed Engr-in-Charge.

Dismantling of cast iron , concrete, asbestos, PVC pipes of any dia and discription from trenches or with walls etc complete all as specified.

S & F in repairs PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 110mm bore) including flat iron claimp for proper fixing complete all as specified by Engineer-in -Charge.

S & F in repairs PVC bends 110mm dia complete all as specified by Engineer-in -Charge.

S & F in repairs PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 75mm bore) including flat iron claimp for proper fixing complete all as specified by Engineer-in -Charge.

S & F in repairs PVC bends 75mm dia complete all as specified and directed.

S&F in repair,500 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, ISI marked, hoisted and fixed in position including tank neeples of required size complete all as specified in SSR Part I complete all as specified and as directed.

S&F in repair, 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered, ISI marked, hoisted and fixed in position including tank neeples of required size complete all as specified in SSR Part I complete all as specified and as directed.

S& F in repairs rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and jointed in position all as specified in SSR Part-I (5000 ltr capacity) including disconnecting existing tank and providing all necessary fittings for connecting with pipe line, metal lockable cover complete all as specified and as directed.

S&F in repairs vitreous China squatting pan 'orrisa' pattern white colour of size 580x440mm with integral foot rests including provision of lime concrete including P traps complete all as specified and as directed.

S&F in repair for vitreous china wash basin white flat backsize 550x400 including cutting for and pinning in ends of brackets including fixing of 32 mm low dencity polylethyne pipes (LDPE)of pressure rating 6kg/cm2,cupling ,PVC connection with 15 mm dia PTMTcheknuts ,brackets all complete as directed by Engr in Charge.

S&F in repair 20mm bore , GI pipe medium grade with all fitting complete fiixed on wall, celling and floor complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore , GI pipe medium grade with all fitting complete fiixed on wall, celling and floor complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel/allmn frame glazed with putty or fixed with wooden /almn beads etc.completed all as specified and as directed by Engr-in-Charge.

S&F in repair 4 mm thick sheet glass,ordinary quality,in squares n exc 0.5 sq m each pane fixed to aluminium frame with rubber gasket or fixed with glass putty as required etc completed all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundation ,filling and mass concrete completed all as specified and as directed by Engr-in-Charge.

S&F Single side writing informatory stainless steel reflecting Sign Boards size 4'x3' having with Aluminium sheet base of 2mm thickness having retro reflective tape base and front colour and matter of sign board will be furnished by Engr-in-Charge.The frame of Sign board shall be 2'' outer dia Square stainless steel pipe and having two legs of stainless steel Square pipe 9' long Each of 2'' outer dia square pipe the board shall be grouted in PCC work of size 350x350x450mm including taking down of existing complete all as specified and as directed.

Taking down Chowkhats or frames n exc 1.5 sqm each without taking of shutter from the frame all as specifed and directed by Engr-in-Charge.

Taking down shutter of any discription exc 1Sqm n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any discription exc 1Sqm and n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge.

S&F factory made 30mm thick solid core Flush door shutter with block board with BWP plywood on both side all as specified directed by Engr in Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and wood grain printed PVC Sheet used 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beaading of 10mm x 10mm used instead of exposed portion of PVC sheet beading for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; supplying & fixing in the frame at site complete all as shown in sketch in SSR Pt-II and directed by the Engineer in Charge.

S&F factory made solid PVC door framing of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube incl fixing in opening as per specification and drawing as shown on page No 150 of SSR Part II complete all as specified and directed by the Engineer in Charge. .

M & L for preparation of new/old wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink wood primer all as specified and directed by Engineer-in-Charge.

S&F stain less steel bright polished bow handle solid type 150mm grip length fency type complete all as specified and directed by Engr -in -charge.

S&F stainless steel bright polished barrel tower bolt with plate with 10mm dia of shoot and 200mm long complete all as specified and directed by Engr-in-Charge.

S&F 100mm long medium grade stain less steel but hinges bright polished fix with nut and bolt complete all as specified and directed by Engr-in-Charge.

S&F 250mm long, 16mm dia stain less steel bright polished door sliding bolt hasp and staple type with fixing of clips 3 Nos with fixing with nut & bolt all as specified directed by Engr in Charge.

M&L for Gunitting work for RCC work as in columns, beam, slab, perapet, chajjas etc by removing all loose concrete on the reinforcement, cleaning the surfaces with wire brushes and reinforcement with sand papers than applying apoxy paint to rusted reinforcement and S&F welded wire mesh fabric size not less than 95x95x3 mm on the prepare surfaces and finally applying guniniting 30 to 40 mm thick (average thickness )with presure gun using 1 part of cement and 3 part of coarse cement incl necessary form work where ever required all gunnited surface shall be brought in complete geometric figure even in the guniting opration only complete all as specified and directed. Note:- Where new or additional reinforcement is required the same shall be paid for separetaly of this schedule as above.

M&L for 6 to 8 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Supply and fix mild steel 1.25 mm thick rolling shutter without ball baring but gear operated with bevel gear box and crank handle including top cover anchor rod, hasp and staple including in two partirtation (as reqd ), including high carban steel spring, locking device and etc all as directed by Engr -in Charge.

Note:- The amount of Rs 1,35,625/- against Schedule of Credit on Page No 137 shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance

PAWAN KUMAR

a.k constructions

SHAMMI ENTERPRISES

Phogat Builders

M/S ujjwal associates