8969/GWL/E8 ADDN/ALTN TO EXISTING SHED OF BLDG NO T-61, STN OFFRS INSTITUTE AT MORAR CANTT GWALIOR

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations etc or for shafts, well cess pits, manholes, pier holes, etc but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25 cm in loose/soft soil complete all as specified and directed.

Earth filling under floor spreading, levelling in layer n.exc 25cm thick each layer including well raming and watering as required complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundations/ mass concrete complete all as specified and directed.

M&L for RCC Design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, base for columns and mass concrete etc complete all as specified and directed.

M&L for RCC Design mix M-25 (using 20 mm graded stone aggregate) as in chajjas, etc complete all as specified and directed.

M&L for formwork to sides of concrete, in foundations, footings, base of columns & plinth beams, etc in flat for rough finshed surfaces of concrete complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges comlete all as specified and directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars, 6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 8 mm and over upto and including 10 mm dia, as in stirrups, spacers, and binders, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for hard core of for broken stone boulder of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate), 75 mm thick finished even and smooth without using extra cement as in plinth protection including forming of joints 10mm wide and 75mm deep and joint filled with bitumin and sand mixture in 1:1 ratio complete all as specified and directed.

M&L for PCC (1:4:8) type D-2, (using 40 mm graded stone aggregate), 75 mm thick, as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in leveling course complete all as specified and directed.

M&L for Non-skid Ceramic tiles 7mm to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 as in floors complete all as specified and directed.

All as per Item No 17 here-in-before but tiles in vertical surfaces of wall set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M&L for 15mm thick rendering on brick or stone/concrete any surfaces in cement mortar 1: 4 on mixed with WPC @ 0.4% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured & paid seperately.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces in cement mortar (1:6) and surface finished even and smooth, complete all as specified and directed.

M&L for 5 mm thick rendering in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surfaces of wall, and applying two coat of distemper oil emulsion over a coat of 1-2 mm wall putty & over a coat of alkali-resistant primming paint complete all as specified and directed.

M&L for applying two coats of cement base paint, including preparation of newly plastered surface of walls complete all as specified and directed.

M&L for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

S&F for 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified colour as approved by Engr-in-Charge complete all as specified and directed.

S&F for 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridge specified, colour as approved by Engr-in-Charge complete all as specified and directed.

S&F for 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and directed.

M&L for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F for anodised powder coated aluminium windows, ventilators shutters, sliding type, aluminium section weighing not less than 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing anodized aluminium snap beading screws, locking latches etc complete all as specified and directed.

S&F for anodised aluminium snap grid frame work for false ceiling consists of powder coated aluminium angle 22x22x1.3 mm and Tee 35x25x1.3 mm of size and grid 600x600 mm complete all as specified and directed.

M&L for Non asbestos fibre cement building boards 6mm thick fixed or laid/inserted to Aluminium anodised frame and hangers framework fixed with Hangers 3-4 mm dia. G.I. (upto reqd length) adjusting level fixed to roof slabs by means of ceilling cleats complete all as specifed and directed

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F for aluminium door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F for curtain rod of Stainless steel 23-25 mm dia pipe thickness not less than 0.8mm of pipe with fixing bracket, side nobes etc fixed on walls with screws with PVC rawl plugs etc complete all as specified and directed.

Surface excavation n.exc 30cm deep and average 15cm deep and getting out soft/loose soil complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed.

M&L for 60 mm thickness machine pressed precast concrete interlocking paver block M-35 any shape and size confirming to IS 15658-2006 in grey cement glossy finish rubber mould casted laid dry over sand cushioning complete all as specified and directed.

M&L for concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade (ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches sockets etc complete all as specified for the following :-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 43 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistranded copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed.

S&F for Modular switch 1 way 6A,1 module complete all as specified and directed.

S&F for Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

S&F for Modular switch 1 way 16A,1 module 15 Amp complete all as specified and directed.

S&F for Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F for Fan step regulator, 120W - 2 module 240 volts, AC 50Hz complete all as specified and directed.

S&F for modular bell push flush type, 5 Amps complete all as specified and directed.

S&F for ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F for Lamp holder with metal ring, PVC/ Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 6500k luminous efficiency 100 lumen/watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

M&L for sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 4 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE : (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/coloumns etc of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

M&L for sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting , Efficiency >130 lumen/watt including reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with regulator complete all as specified and directed.

S&F for exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed.

S&F for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp complete all as specified and directed.

S&F in renewal for sheet metal enclosure double door for distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp, 4 pole & Including MCCB 100 amps 4 pole 16 KA complete (when MCB's are to be used) with suitable size of busbar complete, fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F for MCB DB, sheet metal enclosures double door SPN 8 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F MCB SPN 63 Amps, 240 volts 'C' series 16 KA, including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs complete all as specified and directed.

S&F for modular plate and provisioning of new modular plate of different size including fixing, them in new board. Note : Renewal of any switches, sockets, fan regulator will be measured under separated items.

White cover plate with frame but 2/3/4 module.

White cover plate with frame but 6/8/12 module.

mahamaya constructions (BID ID -3113517)

M/s Ratan Lal Jain and Co. (BID ID -3112986)

M/S NIRMAL SINGH DHANJAL (BID ID -3113394)

BHAGIRATH CONSTRUCTION COMPANY (BID ID -3113950)

ALLIED ASSOCIATES (BID ID -3113955)

BEHL CONSTRUCTION CO (BID ID -3113280)