PROVN OF ATTACHED WASH ROOM, EASY DRYER, HARD STANDING AND INTERLOCKING TILES (04 JOBS) AT ATS UNDER GE (AF) SAMBRA

Amount

Surface dressing not exc 15cm deep and getting out in hard /dense soil complete all as specified and directed

Taking down chowkats or frames exc 1.5 sqm but not exc 4 Sqm each (without taking of shutters from the frame) complete all as specified and directed

Taking down chowkats or frames not exc 1.5 sqm each (without taking of shutters from the frame) complete all as specified and directed

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Dismantling of reinforced Cement Concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and RCC water tanks on roofs (including reinforcement cut as required to facilitate demolition) complete all as specified and directed

Dismantling of brickwork and stone / boulder masonry built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Excavation in trenches not exc. 1.50m wide and not exc 1.5 m in depth; for foundation etc.; or for shafts, wells, cesspits, manholes, pier holes not exc 10 sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed

M&L for PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in foundations, mass concrete filling complete all as specified and directed

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed

M&L for formwork to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc., complete all as specified and directed

M&L for TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for mild steel TMT bars of 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for Reinforced Cement Concrete of M-25 Design Mix for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for Reinforced Cement Concrete of M-25 Design Mix for columns, pillars, piers, posts and struts complete all as specified and directed

M&L for Reinforced Cement Concrete of M-25 Design Mix for beams, cantilevers, bressumm, lintels over 1.5m span complete all as specified and directed

M&L for pre-cast cement concrete block masonry with solid blocks type C1, PCC 1:3:6 ( using 20mm graded stone aggregates) , exc 10cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1, PCC 1:3:6 (using 20mm graded stone aggregates), 10cm thick in width and setting in CM 1:4 complete all as specified and directed

Returning,filling including, spreading, levelling , watering and well ramming inlayers not exceeding 25 cm thick in hard/dence soil comp lete all as specified and directed

Removing surplus excavated soil to a distance exceeding 250m but not exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surface in CM 1:4 for wall finished even & fair complete all as specified and directed

M&L for applying two coats of acrylic emulsion paint of Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on new plastered surfaces of walls complete all as specified and directed

M&L for rendering 10 mm thick on surface other than fair face of block masonry/brick work in CM 1:6 for wall finished even & smooth without using extra cement complete all as specified and directed

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper on walls over a coat of alkali-resistant priming paints over 3mm thick wall care putty complete all as specified and directed

M&L for applying one coats of oil bound distemper on walls over a coat of existing paint complete all as specified and directed

M&L for applying one coats of white wash on ceiling over a coat of existing paint complete all as specified and directed

M&L for broken stone or boulder hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 150mm thick plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in sub base of flooring complete all as specified and directed

M&L for 25mm thick plain cement concrete, type B1, 1:2:4 (using 20mm graded crushed stone aggregates) as in floor complete all as specified and directed

M&L for plain cement concrete , 75mm thick, (1:3:6), type C-1 (using 20mm nominal size crushed and graded stone aggregate) for plinth protection including filling of expansion joint with bituminous mixture finished fair and even complete all as specified and directed

Dismantling floor, hearth / wall tiling including cement mortar bedding (but not backing) and removing tiles & rubbish off the premises complete all as specified and directed

M&L for non skid ceramic tiles, coloured, 7 to 8mm thick (square or rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm, set and jointed in neat cement slurry and pointed in white cement with pigment to match, as in floors laid over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450X300X7mm thick as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles laid over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

S&F single piece white colour vitreous China floor mounted pedastal pattern wash down water closet with seat cover, having PVC 'P' or 'S' type trap element, rimless one piece including all accessoreis complete all as specified and directed. Make:- Cera Cat Part No. S1013217 or equivalent make as mentioned in list of makes of Particular Specifications

S&F Health faucet ABS body with 1mtr SS braided PVC hose pipe complete all as specified and directed.. Make:- Cera, Cat Part No. F8030111AB or equivalent make as mentioned in list of makes of Particular Specifications

S&F over head shower, 100 x 100mm, with 200mm long shower arm and wall flange complete all as specified and directed. Make:- Cera, Cat Part No. F7020110SS or equivalent make as mentioned in list of makes of Particular Specifications

S&F wall mixture with bend pipe for shower and wall flange complete all as specified and directed.. Make:- Cera Cat Part No. F1017401 or equivalent make as mentioned in list of makes of Particular Specifications

S&F angle cock with wall flange complete all as specified and directed. Make:- Cera Cat Part No. F1001201 or equivalent make as mentioned in list of makes of Particular Specifications

S&F corner glass shelf size 225 x 225mm with stainless steel brackets fixed to wall complete all as specified and directed. Make:- Cera Cat Part No. F5005102 or equivalent make as mentioned in list of makes of Particular Specifications

S&F chromium plated soap dish holder complete all as specified and directed.

S&F toilet paper holder with flap guard complete all as specified and directed. Make:- Cera Cat Part No. F5003110 or equivalent make as mentioned in list of makes of Particular Specifications

S&F pillar tap 15mm dia pipe complete all as specified and directed. Make:- Cera Cat Part No. F1001201 or equivalent make as mentioned in list of makes of Particular Specifications

S&F two way bib cock with wall flange and aerator complete all as specified and directed. Make:- Cera Cat Part No. F1001163 or equivalent make as mentioned in list of makes of Particular Specifications

S&F bib cock with wall flange and aerator complete all as specified and directed.. Make:- Cera Cat Part No. F1001151 or equivalent make as mentioned in list of makes of Particular Specifications

S&F brass chromium plated tubular towel rail 600mm long between flanges including all necessary fittings complete all as specified and directed.

S&F vitreous China wash hand basin, white in colour, (counter type oval shaped) of size 560mmX470mmX190mm including bottle trap 150mm including cutting of exisitn Granite top complete all as specified and directed. Make:- Cera Cat Part No. S2030104 & F8060101 or equivalent make as mentioned in list of makes of Particular Specifications

S&F in repairs of brass chromium plated shower rose 125mm size with shower arm fixing with 15 mm pipe complete all as specified and directed.

S&F in repairs of Brass CP mixer for mixing hot & coldwater screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs wall mounted Sheet glass shelf assembly (corner self) consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs 15mm dia bore Bib taps, fancy type, brass chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including necessary brackets & screws as required complete all as specified and directed.

S&F waste coupling 32mm size full thread wth 80mm height for wash hand basin complete all as specified and directed. Make Cera, Cat Part No. F8050101 or equivalent make as mentioned in list of makes of Particular Specifications

S&F PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed.

M&L for 20mm thick granite (of any type) work, (table rubbed and polished) in platform (for counter type WHB) and like in cement mortar (1:4) or pasting over exisitng Cudappah stone slab including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of Granite complete all as specified and directed.

M&L for providing moulding to Granite stone of counters vanities etc including machine polishing to edge to give high gloss finish complete all as specified and directed.

S&F PVC SWR pipe 110 mm bore, single socketed in any length with rubber ring joints,fixed to walls with suitable size mild steel clamps complete all as specified and directed.

S&F in repairs PVC SWR pipe 110 mm bore, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC SWR pipe 75 mm bore, single socketed in any length with rubber ring joints, fixed to walls with suitable size mild steel clamps complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed.

S&F 75mm dia bore PVC (SWR) junction single, (single T) equal or unequal with access door complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) bend of any radius complete all as specified and directed.

S&F 75 mm dia bore PVC (SWR) bend of any radius complete all as specified and directed.

S&F 75 mm dia bore PVC (SWR) bend with oval access door of any radius complete all as specified and directed.

S&F 110 mm dia bore PVC (SWR) bend with oval access door of any radius complete all as specified and directed.

S&F of 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75 mm dia PVC vent cowl complete all as specified and directed.

S&F Unplasticised PVC pipes 40mm bore of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector and fixing to existing pipe complete all as specified and directed.

S&F Unplasticised PVC pipes 25mm bore of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe including all fitting such as bends,elbows, tees tank connector and fixing to existing pipe complete all as specified and directed.

S&F 15mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe including fitting such as bends,elbows, unions, tees, reducing tees, adopters, sockets, plugs, hose clips, brass fittings etc., complete all as specified and directed.

Supplying and laying of 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. fixed complete to walls, ceilings or in floors etc., complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exc 20 cm complete all as specified and directed. girth

S&F rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) three layered in wall construction hoisting and fixed in position complete all as specified and directed.

S&F nipple suitable forHDPE water tank.(Minimum weight 15mm-38gms/20mm?45gms /25mm- 65gm complete all as specified and directed.

M&L for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door chowkhat of size 65 x 100 mm (single groove) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door chowkhat of size 65 x 125 mm (double groove) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter (single/double leaf) of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicityindex of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

M&L for providing and fixing factory made wire mesh solid WPC (Wood Polymer Composite) door shutter (single/double leaf) consisting of density density of 500 kg/cum, door to be with SS mosquito wire mesh and XTN aluminium mesh for additional strength and safety pourpose. the door should be water proof, termite proof, fire retardant, and having screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. fixing with butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F 100 mm long butt hinges stainless steel to door frame with necessary screwing or bolting complete all as specified and directed.

S&F 150 mm long aluminium anodised handle fabricated type complete all as specified and directed.

S&F 100 mm long aluminium anodised handle fabricated type complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolt complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised sliding door bolt with hasp and stapple bolt type complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised sliding door bolt with hasp and stapple bolt type complete all as specified and directed..

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel, or flat section) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) quality - A complete all as specified and directed.

S&F pre painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for mild steel work for wind ties for roof including securing bolts including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 etc., complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enemal paint over a coat of red oxide Zinc chromate primer complete all as specified and directed.

M&L for providing and fixing 12mm thick Gypsum board in ceiling as per manufacturer instruction over and including powder coated aluminium snap grid frame work (size of grid 605 x 605mm) supported by hangers 2 to 4 mm dia GI (up to 1200mm length /as per site requirement) adjusting level fixed to roof slab/walls/wooden/steel members by means of ceiling cleats and painting two coats of oil bound distemper over a coat of primer and preparatory work complete all as specified and directed.

M&L for cutting holes in brick/ stone walls built in cement mortar for inserting hold fasts of depth of embedded portion exc half brick but not exc one brick from the face of the jamb in to the wall and making good dismantled portion in cement mortar 1:3 or Cement Concrete 1:2:4 type B-1 as required complete all as specified and directed.

M&L for providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ 0.2mm thick galvanised steel Frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of Zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose - Area not exceeding 2.00 sqm each)

S&F in repairs factory made uPVC white colour glazed ventilator (louver type frame and arrangement for fixing of exaust fan with the uPVC frame) made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and directed. Note:- The unit rate quoted by contractor shall includes all connected accessories. Net opening shall be measured for payment purpose). (ii) Glass shall be measured and paid separately

S&F anodised aluminium grills powder coated of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws @200 centre to centre, including cutting the grills to proper opening size for fixing and operation of handles and fixing fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

S&F figured glass, pin head type 4 mm thick, not exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed.

S&F sheet plain glass 5.5 mm thick, ordinary quality, in squares exceeding 0.5 Square Metre for each pane, glazing with oil putty or aluminium beading complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws or aluminium beading complete all as specified and directed.

S&F in repairs Gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends internally IS-778 marked, Class-2 for iron pipe of size 40mm bore complete all as specified and directed.

S&F ceiling mounted pully operated cloth drying system consisting of anodised aluminium pipe, each of outer dia 22mm and inner dia 19.8mm, 6 Nos pipe 2.5m length with 3/4 mm dia polyster braided undyed rope with channel mounted screw of 38mm x 8 self tapping including all accessories complete all as specified and directed.

Excavating over areas, not exceeding 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

M&L for 200mm thick soling with broken quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber with plate vibrator complete all as specified and directed.

M&L for 100mm thick plain cement concrete, type D2, 1:4:8 (using 40mm graded srushed stone aggregates) as in hard standing complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 80mm thickness, M-40 grade with grey cement and pigment interstices complete all as specified and directed.

M&L for providing precast cement concrete in PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in kerb stone finished smooth using extra cement including necessary mould/form work and jointed in CM 1:4 struck flush with same mortar complete all as specified and directed..

Supply, installation, testing and commisioning of solar Hot water system (Flat Plate collector) based on indirect transfer of heat of capacity 500 LPD with electrical back up by 3 KW heating elements each 3 phase of two numbers and thermostates collectors of ISI marked with laser required Flate Plate collectors and laser welded tubes with stainless steel hot water storage tank 500 ltrs including supply and fixing of SS heat exchanger made of SS 304 pipe as per OEM inside hot water tank, providing angle iroin structure of reqiured size for collectors and angle iron staging for the hot water tank with required size made out of minimum 25 mm x 4 mm angle iron flats duly welded, PCC work 1:2:4, Type B1 (using 20mm graded crushed stone aggregates) for fixing of Solar hot water heating system including electrical connection from solar water heater to sheet metal plug top with 3 Core PVC insulated sheated multistandard copper cable including earthing wire with casing capping as required at site complete all as specified and directed .

M&L for 20mm outer dia PPR pipe three layer (SDR 7.4 (P N 1.6) UV with all fitting such as collars, reducers, tees, nipples, union, wall clamps etc including brass stainless steel male/female threaded fittings for fixing stop cock, bib cock of 15 mm dia fixed on wall/ roof complete all as specified and directed .

S&F Gun metal globe or gate values, with iron wheel head, screwed both ends for iron pipe and fixed of size 15 mm bore dia of pipe complete all as specified and directed

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod of high density plastic ball of 25mm dia ( minimum weight of 455 grams) complete all as specified and directed

M&L for submain wiring using single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 4 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including casing capping of dia not less than 25 mm dia with standard acessories, along with two run of FRLSH PVC insulated, unsheathed, stranded copper conductor of size 2x 4 Sqmm as earth continuity conductor all as specified and directed Note-4 runs of single core FRLSH PVC cable 4 sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit

S&F Gun metal globe or gate values, with iron wheel head , screwed both ends for iron pipe & fixed of size 25 mm bore dia of pipe complete all as specified and directed .

S&F GI tubing medium grade with all galvanised fitting laid on wall / floor of 25 mm bore including cutting the existing 25 mm dia GI pipe & connecting up the new pipe line including all necessary fittings complete all as specified and directed .

S&F MCB Single pole & neutral 240 volts 6 to 32 Amps 10 KA rupturing capacity complete all as specified and directed . .

S&F Sheet metal enclosure for distribution boards flushed in wall double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar,SPN 4 ways complete all as specified and as directed Note :Cost of cutting/chasing of wall and making good disturbed surfaces shall deemed to be included in the quote rate

S&F bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

M&L for plain cement contrete 1:3:6, type C -1 (using 20 mm granded stone aggregates) for coping of the pole including use & waste of from work complete all as specified and directed

M&L for angle or tee sections, fixed independently, without connection plate etc for staging of make up water tank (Fe 320-Grade E-165) including necessary drilled holes, weided together complete all as specified and directed

M&L for rotational moulded polyethylene water storage tank (Cylindrical vertical) with closed top of capacity 1000 ltrs, three layered in wall construction hoisted & fixed in position complete all as specified and directed

S&F 415V 10KA 'B' curve miniature circuit breaker (MCB) of capacity TP 25 To 63 AMP and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed

M&L for point wiring for one 3 pin socket outlet 15 Amps independent board with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 4 sqmm 1100 volts grade drawn through in existing conduit with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 2.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed

S&F single pole and neutral enclosure with two pin and earth plug and socket complete with one single pole MCB 10 Amp complete all as specified and directed.

S&F water heater storage type 25 Ltr capacity, BEE 5 star and 8 bar pressure rated stainless steel (minimum wall thickness 2 mm) tank with feroglass coated inner container energy saving high density PUF insulation vertical ABS shock proof plastic body grouting of studs in wall in cement motar (1:3) nuts, washers, provision of two Nos PVC braided connection 450mm long heavy duty with brass nuts and two Nos brass chromium plated angular valve, thermostat, NRV , top plug 20 Amps, valve flange suitable for 15mm bore pipe for water supply connection complete all as specified and directed

M&L for point wiring for one fan or light or exhaust fan or bell/buzzer point controlled by one switch with stranded FRLSH copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC casing capping 20/25 mm width medium duty ISI marked, including fittings such as tees, bends etc terminating in and including modular metal box, modular white cover plate any size with support frame any size module complete all as specified and as directed. cover of approved make, including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed

All as per Srl item No.123 here-in-before but socket point on the same board with other switches -ditto-

S&F modular switch single pole 6 Amps One Way Switch AC 230V, 50HZ supply complete all as specified and as directed. Make : Cat Part No. 800100 of IndoAsian ELVIRA/ ACWSXXW101 of Havells CRABTREE(Signia) make or any equivalent make as specified in list of makes of Particular Specifications

S&F modular switch single pole 16 Amps One Way Switch with indicator AC 230V, 50HZ supply complete all as specified and as directed. Make : Cat Part No. 800105 of IndoAsian ELVIRA/ ACWSXIW161 of Havells CRABTREE(Signia) make or any equivalent make as specified in list of makes of Particular Specifications

S&F modular socket 5A AC 230V, 50HZ complete all as specified and as directed. Make : Cat Part No.802800 of IndoAsian ELVIRA/ACWKPXW063 of Havells CRABTREE(Signia) make or any equivalent make as specified in list of makes of Particular Specifications

S&F modular socket combine 6A/16A multi purpose AC 230CV, 50Hz complete all as specified and as directed. Make : Cat Part No.800122 of IndoAsian ELVIRA/ACWKCXW163 of Havells CRABTREE(Signia) make or any equivalent make as specified in list of makes of Particular Specifications

S&F ceiling rose surface backelite three terminal 240 volts complete all as specified and directed

S&F LED lights fitting 1x 20W, 220V, wall mounted LED batten with Aluminum Housing & integrated electronic driver including connecting up with 0.5Sqmm three core flexible copper conductor cable from ceiling rose complete all as specified and as directed. Make:-Cat Part No: LUMILINE+BS20WLED830SPCSSIND of Havells make or any equivalent make as specified in list of makes of Particular Specifications

S&F sub main wiring with 2 single core 06 sqmm multi-stranded FRLSH PVC insulated cable unsheathed 1100 volts grade with one earth wire of 06 sqmm copper conductor cable connected to common earth dolly complete and including PVC casing caping minimum 25 mm width complete all as specified and as directed Note- Two run of 6 sqmm for phase, neutral and one run of 6 sqmm for earthing shall be measured as 1 RM.

S&F sheet metal enclosure double door factory made distribution board 240 volts SPN 4 way, 200 Amps rated bus bar complete all as specified and as directed.

S&F sheet metal enclosure double door factory made distribution board 240 volts SPN 8 way, 200 Amps rated bus bar complete all as specified and as directed.

S&F MCB SPN 6 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

S&F MCB SP 06 to 32 Amps, C Curve, 240 volts, 50 Hz AC supply complete all as specified and directed.

S&F exhaust fan, steel body AC single Phase. 230V of size 300m sweep with blades, frame and louvers including cutting the wall as round shape for exhaust fan complete all as specified and directed.

M/S MAHADEV M PATIL (BID ID -3480668)