REPAIR AND MAINT OF EOT CRANES AT VARIOUS CAPACITY/ LOCATIONS UNDER GE(A) JAISALMER

Material and labour for The following spares/ parts to be serviced/checked and if found defective to be replaced of flame proof EOT Cranes of capacity 2/3/5 tons. (a) gear oil in gear boxes (b) Grease the whole crane movable parts as recommended by OEM. (c) Before filling the gear oil clean the gear box inside and outside by using diesel (d) Rolling wheel of long travel (e) Thruster break oil level (f) Breaks (g) Motors servicing/rewinding. (j) condition of couplings (k) nuts & bolts conditions. (m) break shoe fitted on the break of the crane. (n) limit switch fitted on the crane . (o) Step down transformer, single phase preventer, terminal block, MCB, HRC and DBR. (p) VFD installed. (q) pendant, push button . Note : (i) All unserviceable spare parts to be replaced shall be measured and paid separately under relevant item of Sch A. (ii) Cost of Grease and other minor parts like nuts,bolts,washers,pins shall be deemed included in unit quoted rate. (iii) Carrying out load test on flame proof EOT cranes 2-20 Ton capacity under 110% of full load capacity of cranes on hoisting, long travel and cross travel for checking the performance including deflection test with necessary manpower, instruments, necessary internal transportation upto required length of cranes, complete all as specified and directed . (iv)writing date of test and next due date for testing on the crane with white synthetic enamel paint over a black strip of synthetic enamel paint shall be carried out by the contractor.(v) Material and labour for Load testing shall be arranged by the contractor at his own and the rate of this item include the cost thereof.(vi) Testing of particular crane shall be scheduled by Engineer-in-Charge.(vii) Load testing and caliberation of EOT crane carried out in the presence user rep & JE E/M/Engineer-in-Charge. Load / deflection test for all EOT Cranes shall be carried out by the contractor through licensed crane inspector in presence of department rep as directed by the GE & user rep and recording of test result & certificate will be issued by the same.(viii) Load testing shall be carried out only after carrying out servicing of EOT cranes i.e. after execution of item no 1 to 3

All as per item No 1 here-in-before but capacity of crane 10 ton complete all as directed

All as per item No 1 here-in-before but capacity of crane 20 ton complete all as directed

Supply & fix in replacement FRLS, 4 core 6 sqmm PVC insulated PVC sheathed multistranded copper conductor cable on the existing conduit/carrier complete all as specified and directed.

Supply & fix in replacement FRLS, 4 core 4 sqmm PVC insulated PVC sheathed multistranded copper conductor cable complete all as specified and directed.

Supply & fix in replacement FRLS, 6 core 2.5 sqmm PVC insulated PVC sheathed multistranded copper conductor cable complete all as specified and directed.

Supply & fix in replacement FRLS, 12 core 1.5 sqmm PVC insulated PVC sheathed multistranded copper conductor cable complete all as specified and directed.

Supply & fix in replacement FRLS, 22 core 1.5 sqmm PVC insulated PVC sheathed multistranded copper conductor cable for crane remote operate complete all as specified and directed.

Material and labour for disconnecting electric connections of 3 phase motor 0.5/0.75/1 HP capcity, 415 Volts AC supply of EOT crane, taking out from the crane, dismantling / opening of motor, cutting and taking out burnt winding wire, cleaning of slots by removing dust etc. and rewinding with super enamelled copper winding wire of existing gauge and class of insulations as per original manufacturers design including varnishing replacing insulation papers insulated sleeves etc. complete reassembling and reinstalling and testing on full load complete all as specified and directed.

All as per item No 9 here-in-before but Motor capacity of 1.5/2 HP complete all as specified and directed.