GE 861EWS-59/2021-2022

Amount

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc

Demolition of brick or stone masonry built in cement mortar including all necessary arches quoins etc.

Demolition of cement concrete (unreinforced in ground floors & pavings n.exc 15 cm thick (below or above ground level)

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store.

Demolition of reinforced cement concrete of any description ( reinforcement cut as reqd to facilitate demolition ).

Taking down chowkhats or frames not exc. 1.5Sqm but with shutters (without taking off shutters from the frames)

Taking down chowkhat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each

Taking down shutter of any description n/exe 1.00 sqm each

Taking down shutter(any description) area exceeding 1 sqm but not exceeding 2 sqm each.

M&L Flush pointing to random rubble masonry, uncoursed or brought upto courses in CM 1:3, complete all as specified.

M&L for brick work with sub class ‘B’ brick straight or curved on plan exceeding 6m mean radius in CM 1:4 complete all as specified.

Description all as per item No 11 above but excepts bricks.

M&L for squared rubble walling , brought up to courses , well bounded , bedded and solidly hearted , built in CM (1:6) complete all as specified.

All as per the description of item No 13 here-in- before but but except stones.

M&L rendering 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) complete all as specified and directed.

M&L rendering 10 mm thick CM 1:4 on fair faces of brick work or concrete surface complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 finishing on brick or concrete surfaces finished even & smooth without using extra cement in ceiling all as specified and directed.

M&L for RCC 1:1.5:3 M20 ,Design mix type B1 (using 20 mm graded aggregate ) as in slabs supported on walls, beams, and columns etc complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floors, slabs , landing and similar works etc all as specified as directed.

M&L for MS TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for columns, hooking end and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded aggregate as in floor to receive floor finishes etc. all as specified.

S&F vitrified ceramic dark shade coloured tiles 10mm thick (square/rectangular) polished, area of each tiles n. exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 all as specified and directed.

M&L for vitrified tiles Granite /Marble /wood textures ceramic 10 mm tiles in vertical surfaces or floors n/exe 0.36 Sqm , over 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or colored cement to match all as specified and directed.

M&L for Non skid ceramic coloured joint free tiles 400mm x 400mm /300mmx300mm 7to 8mm thick (square/ rectangular), in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) laying floor finish complete all as specified and directed.

M&L for Non skid ceramic coloured joint free tiles 300mmx300mm 7to 8mm thick (square/ rectangular), in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) laying floor finish complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces 300mm x200mmx7) mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tile laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls complete, all as specified.

M&L for glazed ceramic tiles in vertical surfaces 350mm x250mmx7 mm /450mmx350mmx7mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tile laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls complete, all as specified.

M&L for kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match thick shade of the slab including rubbing and polishing laid over 15mm thick screed bed in CM (1:6) complete all as spd.

All as per item No 28 above here-in-before but on vertical surfaces of walls /skirting/dado laid over and including 10mm backing coat in CM 1:4 etc complete all as spd.

M&L for 75 mm thick PCC (1:4:8) type B2 (using 40 mm graded aggregate ) as in sub for receiving floor finishes etc all as specified and directed.

M&L for chequerd cement concrete tiles 20cm x20cmx25mm th with grey cement and pigment , set , jointed and pointed in neat cement slurry in floors laid over 15 mm thick screed bed in CM 1:6 all as spd & directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15656 -2006 of 60 mm thick M -35 all as specified and directed.

M&L for sand filling 50 mm under floors or foundation, and receiving to interlocking tiles, all as specified and directed.

M&L 2nd class hard wood, plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified.

S&F 2nd class hard wood (Sal/Hollock) 35 mm thick paneled shutter (any number of panels )with panels of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified.

Supply and fixed 35mm thick 2nd class hard wood(Sal/Hollock) glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (internal sash bars) edges of framing plane, chamfered or rounded fitted and mitered beads for securing glass etc size of members as specified in SSR Part-I Section 8 clause 8.24(a) complete all as specified.

S&F for 30 mm thick 2nd class hard wood (Sal/Hollock) glazed and skeleton windows/ventilators shutters open rebated and prepared to receive glass, gauge etc , divide into square with plain chamfered or rounded, mitered and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelam PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail paneling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified.

S&F for aluminium door of extruded aluminium section , consisting of frame vertical and horizontal members of size 100mmx45mmx 2.5mm thick with shutter stile 85mmx45mmx2.50mm thick , top middle and bottom rail of size 101.60mmx44.5mm with 5.50 mm thick tinted sheet glass and PVC prelaminated particle board 10 to 12 mm thick with aluminium beading and rubber gasket/beading including fixing of hydraulic floor spring one in single leaf or two nos in double leaf door. One mortise lock for aluminium door (each) and two Nos 200 mm long aluminium tower bolts and two nos alu handles D type for each door. Fixing with rawl plug including rectification of floor/wall to match the existing surfaces all as specified and as directed by Engr-in-Charge.

S&F for aluminium for fully gazed window openable shutter with aluminium section , consisting of frame vertical and horizontal members of size 100mmx44.45mmx1.90 mm thick for frame and section for shutter 45mmx44.5mmx1.9mm thick with 5.50 mm thick tinted sheet glass with aluminium beading and rubber gasket/ beading clip 3 nos 150 mm long , handle 02 nos D type , 75 mm long alu butt hinges min 02 nos in each leaf. Fixing with rawl plug including rectification of jambs floor/wall to match the existing surfaces all as specified and as directed by Engr-in-Charge.

S&F for aluminium partition with aluminium anodised tube of section 114mm x44.5mm x1.5mm thick at bottom and remaining vertical and horizontal rail of section 44.5mm x45mm x 2 mm thick aluminium clip rubber beading aluminium angle nut bolts etc (from bottom 75 cm height both side PVC prelaminated board, 10 to 12 mm thick ISI marked (Novapan/Kitlam) and remaining parts of partition be covered with glass 5.5 mm thick , spacing of glazed aluminium tube in horizontal 75 cm (max ) and vertical 90 cm (maximum) complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolts of extruded section 200mm long complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolts extruded section of size 150 mm, all as specified and directed.

S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long , all as specified and directed

S&F aluminium handle extruded fabricate type anodised of size 150 mm complete all as spd and directed.

S&F in repair aluminium handle extruded fabricate type anodised of size 150 mm complete all as spd and directed.

S&F aluminium handle extruded fabricate type anodised of size 100 mm complete all as spd and directed.

S&F in repair aluminium handle extruded fabricate type anodised of size 100 mm complete all as spd and directed.

S&F for butt hinges 100mm medium weight cold rolled mild stee lall as specified and directed.

S&F in repair butt hinges 100mm medium weight cold rolled mild steel all as specified and directed.

S&F in repair butt hinges 75 mm medium weight cold rolled mild steel all as specified and directed.

S&F butt hinges 75 mm medium weight cold rolled mild stee lall as specified and directed.

S&F MS helical door spring including roller & roller plate complete 300 mm size complete all as specified & directed.

S&F in repair MS helical door spring including roller & roller plate complete 300 mm size complete all as specified & directed.

S&F 150 mm long floor door stopper of alu alloy body and tongue, anodised with hard drawn steel spring all as specified and directed.

S&F in repair 150 mm long floor door stopper of alu alloy body and tongue, anodised with hard drawn steel spring all as specified and directed.

Hacking out old broken glasses thickness size quality from wooden or steel frames glazed with old putty or fixed with beads all as specified and directed.

M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane all as spd.

M&L 4mm thick figured glass pin headed type and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane all as spd.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified and directed.

Dismantling water storage tanks of any description/ exc 500 liters capacity and removing from site complete all as specified.

S&F for Rotational moulded polythylene 500 liters capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated alu rod & high density plastic ball complete all as specified.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squatt pattern closet including lime concrete bedding and all joint making good to the floor all as specified.

S & F in repair vitreous china bowl urinal flat back, size of (465 x 355 x 265) mm white (min), with grating and union for discharge pipe including flushing system, flush pipe & waste pipe) all as specified & directed.

S&F in repairs floor gratings of PTMT for 125mm dia(Minimum weight 40gms) all .as specified and directed

S&F in repair PVC valve less 10 liter capacity symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge.

S&F in repair Vitreous china wash hand basin, with pedestal Vitreous china white, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed. (Including 15mm bore CP pillar tap, waste coupling and 32mm dia PVC waste pipe) all as specified and directed.

S&F in repairs 15 mm size PVC connection with PTMT nuts of 600 mm long all as specified and directed.

S&F in repairs 15 mm size PVC connection with PTMT nuts of 450mm long all as specified and directed.

S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms ) all as specified and directed.

S&F 100 cast iron sanitary connection for WC complete all as specified.

S&F in repairs for cast iron 75 mm bore soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floor etc all as specified and directed

S&F in repairs for cast iron 100 mm bore soil, waste and vent spun pipes in any length with or without ears, with cement joints, laid in trenches or in floor etc all as specified and directed

S&F in repairs 75 mm dia CI floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1all as specified and directed.

S&F cast iron Nahani trap 75 mm dia including jointing to pipe complete all as specified and directed

S&F in repairs cast iron 75 mm bore bends diminishing pieces or tapers etc all as specified and directed

S&F in repairs cast iron 100 mm bore cowls complete all as specified and directed

S&F in repairs 15 mm bore fancy type CP bib taps cast copper alloy with crutch or butterfly nuts , handle, screwed down for iron pipe.

S&F in repairs, 15 mm bore CP stop/angle valve cast copper alloy screwed down , high pressure with crutch or butterfly handle fancy type all as specified and directed.

S&F in repairs, 15 mm bore CP stop/angle valve with long shank and cup (concealed type) cast copper alloy screwed down , high pressure fancy type all as specified and directed.

Taking up or down 15mm dia GI Tubing and connections including cleaning for refixing complete all as specified.

Taking up or down 20 mm dia GI Tubing and connections including cleaning for refixing complete all as specified.

S&F 15 mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc all as specified and directed.

S&F 20 mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc all as specified and directed.

Fixing only GI tubing in any grade to walls or floors 15 mm including fittings all as directed.

Fixing only GI tubing in any grade to walls or floors 20 mm including fittings all as directed.

S&F in repairs aluminium anodised tubular towel rail, 20mm dia, D type, 60 cm long between flanges all as specified and directed

S&F in repaired vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipe etc complete all as specified.

15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified.

S&F in repair health faucet CP Brass hand Jet Shower 15mm bore dia and 1500mm long CP pipe complete all as specified and directed by Engr-in-Charge (Make- Jaquar or equivalent) complete all as specified.

S&F in repairs Pillar tap 15mm chromium plated fancy type cast copper alloy with crutch or butter fly handle, screwed down for iron pipe and fixed complete all as specified.

S&F in repairs bib tap 15mm PTMT any colour high pressure screwed down for iron pipe and fixed ( Minimum weight 90gms) complete all as specified.

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specified.

S&Fin repairs 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified.

S&Fin repairs 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified.

S&F PVC (SWR) bends of 75mm, all as specified.

S&F PVC (SWR) bends of 110mm, all as specified.

S&F 110mm PVC (SWR) vent cowl complete all as specified.

S&F 75mm PVC (SWR) vent cowl complete all as specified.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards/slabs including cover fillets etc complete all as specified.

S&F for anodised aluminium snap grid of size 605 x605 mm frame work for false ceiling including straining with GI wire 4 mm thick all as specified.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm thick plain PVC sheet suitably placed in false ceiling grid made of aluminum GI/MS as per specification and drawing complete all as specified.

S&F for solid PVC wall paneling decorative type consisting of 5 mm thick plain colour PVC pre-laminated sheet inclusive of solvent cement and and fixing at site on PVC frame complete all as specified.

S&F for 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified.

S&F for 9 mm thick veneered decorative plywood , grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame on wall and ceiling etc complete all as specified and directed.

S&F 2nd class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 06 but not exc 13 sqcm complete all as specified

S&F in repairs 40mm thick , 2nd class hardwood planks , planed one side with butt joints and fixed with nails fixed in any situation complete all as specified.

M&L in repairs for weather boarding in 2nd class hardwood clean swan , plain , 20 mm thick or feather edges , 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified.

S&F in repairs timber frame in second class hard wood as in scantling etc complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc complete all as specified.

S&F for galvalume aluminium zinc coating GI based pre-painted corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

S&F for galvalume aluminium zinc coating GI based pre-painted plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers in roof etc.with grade of zinc coating 275 complete all as specified.

S&F 0.80mm thick plain galvanised mild steel sheeting in ridges, hips valley gutters, drip and straight flashings (length and girth as fixed)with grade of zinc coating 275 complete all as specified and directed.

Dismantling structural steel work including doors, gates, etc

S&F for Hand rails, half round or other stock section , nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S & F for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters conforming to Fe 410-W(Gde -E250) quality A grade complete all as specified and directed.

S&F framed work such as grills, grating etc with guard bars,feamed guard bars, hold fasts,, railing, framed work of water tanks and similar work confirming to Fe-290 gde-E165 complete all as specified and directed.

M &L for preparing plastered or un plastered new surface of walls and applying two coats of Cement base paint on walls(Externally) over priming with alkali resistant priming paint on walls all as specified.

M&L for applying 3 mm thick wall care putty on wall including preparation new surfaces plastered or unplastered surfaces applying two coats of oil bound distemper on newly plastered surfaces of wall

M&L for applying one coat of white wash on old plastered surfaces of wall including preparation of surfaces complete all as specified.

M &L for preparing plastered or un plastered new surface of walls and applying three coats of white wash on ceiling complete all as specified.

M &L for preparing plastered or un plastered old surfaces of walls and applying one coat of Cement base paint on walls.(External) complete all as specified.

M&L for applying 3 mm thick wall care putty on old surfaces of wall and including two coats of oil bound distemper on plastered/ unplastered surfaces of wall including complete removal of existing treatment complete all as specified.

M&L for two coats of synthetic enamel paint on new woodensurfaces over coat of pink primer to new surfaces including preparation of surfaces, over 10cm width or girth complete all as specified.

M&L for two coats of synthetic enamel paint on new steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth including roof painting complete all as specified and directed.

M&L for one coat of synthetic enamel paint on old wooden SURFACES including preparation of surfaces over 10cm width or girth complete all as specified.

M & L for preparation of old steel surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint including roof painting complete all as spd.

M&L for PCC (1:2:4) type B2 (using 40 mm graded aggregate) as in surface channel of drain complete all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement using extra cement including forms, moulds, mitered / stopped ends etc complete all as specified.

M&L for 40 mm thick PCC (1:2:4) type B1 using 20 mm graded aggregate as in floor , finished even & smooth without using extra cement complete all as specified.

Supply glass dividing strips, 38x3mm thick as in floors complete all as specified.

M&L for 100 mm thick PCC (1:2:4) type B2 (using 40 mm graded aggregate ) as in floor over sub base , finished surface even and smooth without using extra cement , laid in alternate bays and joint filled with mastic filling including necessary form work complete all as specified.

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

S&F in repairs for Harrison rails/drapery rod 25 mm dia mild steel , chromium plated decorative type with 02 Nos wood finished side brackets/ fenals for each curtain rod all as specified and directed.

S&F Providing precast cement concrete louvers and jallies, 25mm thick, type B-0 (1:2:4) 12.5mm graded aggregate, (measured solid), including all mouldings but excluding frame, set in CM 1:4 incl two coats of cement base paint over a coat of alkali based primer after preparation, complete all as specified as directed by Engr-in- Charge

M&L for granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over and including 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M&L precast cement concrete type B-1 1:2:4 (20mm graded stone aggregate) as in cover slab for manholes/septic tanks and setting in cement mortar 1:4 all as specified and directed.

M&L Plain cement concrete type B1 1:2:4 (using 20mm graded curshed stone aggregate) in copings, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary form work, all as directed

S&F in repair 20 mm Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20mm-210gms).

M/S LATIF AHMAD BABA CONSTRUCTION

M/S Ghulam Hussain Lone

M/s Pall Constructions