SPECIAL REPAIR TO P505/01 TO 06 P515/01 TO 06 P516/01 TO 06 and P517/01 TO 06 (24 QTRS) OF SANJAY KUMAR ENCLAVE UNDER GE (S) PATIALA

Taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specfied and as directed by Enginer-in-charge

Material and labour for rendering 10mm thick on brick work or concrete surfaces in cemet mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 5mm thick as on ceilings or concrete surfaces in cemet mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 15mm thick on brick work or concrete surfaces or on chajjas / parapet walls etc in cemet mortar 1:4 mixing with liquid water proofing compound as per manufacturer's instructions finished even and fair without using extra cement including fixing of chicken wire mesh where directed complete all as specified and as directed by Engineer-in-Charge. Note: Liquid water proofing compound and Chicken wire mesh shall be measured and paid as supply only separately

Supply only integral liquid water proofing compound complete all as specified and as directed by Engineer-in-Charge.

Supply only chicken wire mesh 22 gauge of size not less than 20x20 mm complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment of any type / description from ceilings /RCC surfaces etc with mechanical means/grinder complete all as specified and as directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment of any type/description from walls/RCC surfaces etc with mechanical means/grinder complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of walls and applying two coat of OBD over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old plastered surfaces of wall and applying two coat of OBD complete all as specified and as directed by Engineer-in-Charge..

Material and Labour for exterior painting work including complete removal of existing loose paint layers till plaster level by using jet pressure washer and crack filling up to 3mm by using crack seal & up to 10mm by using textured crack filler. Touch-up by using wall putty with silicon additives followed by application of one coat of SmartCare waterproof primer (Damp Prime Suprema) on walls and Chajjas with 10% of dilution of water and applying two coats of 100% acrylic smooth emulsion exterior grade with silicon additives having anti-algal and Dust pickup resistance properties, Material should be applied (Dilution, Recoating period etc..) as per manufacturers instructions by using fully automatic air less spray machine having flow speed of minimum 1ltr per minute and pressure of 3300 PSI. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered/unplastered external walls / RCC surfaces / soffits of chajjas /roof projections /cantilevers/balcony etc and applying two coats of exterior emulsion weather proof paint (light shade) @ 5 sq.m/litre/2 coats by using roller to over & including a coat of exterior wall primer @ 10 sq.m/1.43litre/1 coat complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old plastered surfaces of ceiling and applying two coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description, over 10 cm width or girth nt otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Material and labour fo preparation of old steel surfaces of any description, over 10 cm width or girth not otherwise described and applying one coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

Supply and apply of rust remover cum passivator by brush in two coat @ 0.3 kg/m2/coat of Density: 1.01 Kg/l at 300C complete all as per manufacturer's instructions and all as specified. Note : The application of rust removal shall be got done through the authorised applicator of manufacturer of membrane only complete all as specified and as directed by Engineer-in-Charge. Make: Sika Rustoff 100 and fosroc or equivalent as approved by GE

Supply and apply Cementitious Coating for Corrosion Protection having a cement based polymer modified rebar corrosion protection system by appling the first coat approx. 1mm thick layer of product carbonation resistance 2 mm of SikaTop Armatec®-108 or equivalent as specified corresponds to 20 mm of normal mortar; bond strength > 1N/mm2 according to ASTM C 882-78 applying @ 4 kg/m2 for two coats on the prepared reinforcing steel with a medium- stiff brush. It is unavoidable that Sspecified product will also be applied onto the surrounding concrete. The second coat is applied in the same way after a waiting time of 2-3 hours (at +20°C) as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. Note : The application of Cementitious Coating for Corrosion Protection shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. Make/Product: SikaTop®-Armatec-108 and fosroc or equivalent as approved by GE.

Material and labour for providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface by chipping and throughly cleaning of surface complete whereever required Consumption 0.5 kg/m2. complete all as per manufacturer's instructions and Product requirements : Complies with ASTM C 881 Type II Grade 2 Class B+C.complete all as specified and as directed by Engineer-in-Charge. Note : The application of Epoxy Bonding Primer shall be got done through the authorised applicator of manufacturer of membrane only as approved by GE.. Product: Sikadur®-32 LP and fosroc or equivalentas approved by GE.

Supply and apply a pre-batched one component polymer modified cementitious patch repair mortar in 25 mm thickness.Yield: approx. 0.84 ltr/kg.System requirements: compressive strength >= 50 N/mm2 (after 28 days) according to ASTM C 109; flexural strength >= 3N/ mm2 (after 7 days) according to ASTM C 293-79.Consumption of 2.1 Kg/Sqm/mm complete all as specified and as directed by Engineer-in-Charge. Note : The application of Polymer repair Mortar shall be got done through the authorised applicator of manufacturer of membrane only as approved by GE. Product: SikaTop®-122 HS or equivalent from Fosroc as approved by GE.

Taking down existing plaster from brick work or concrete surface and cleaning the surface properly and washing with water etc to prepare for efforescence treatment.(i) Apply two coats of smart care damp proof coating of make Dr fixit (Pedilite Co.), Asian paints,Berger paints, Nerolac paints or equivalent (II) Rendering 15 mm thick over treated surfaces in CM 1:4 mixed with URP (301) approved by GE complete all as specified and as directed by Engineer-in-Charge. Note : The complete item shall be got executed through the authorised applicator of manufacturer only and complete all as directed by Engr-in-charge. Applicator shall be got approval by GE before execution of work.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing , supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joining together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 100 mm size Stainless Steel (304 Grade) Butt hinges complete all as specified and directed by Engineer-in-Charge.

Supply and fixing aluminium anodised barrel tower bolt 150 mm long of extruded section complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door Frame/Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specifed and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door Frame/Chowkhat of size 150 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specifed and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,complete all as specified and directed by Engineer-in-Charge.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type plain wiremesh door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk)and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. For fixing stainless steel 304 Grade wire cloth (wire dia. 0.56mm) and Expanded aluminium mesh, wire dia 1.20 mm thickness and mesh aperture size 38x20mm (LWxSW) combinly panel panel area of door excpet stiles and rail to be panelled with mesh wih self tapping round headed screws at requried distance,scres and edges covered with feathered pvc edge beading all round of mesh and WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws,,complete all as specified and directed by Engineer-in-Charge.

Supply and fixing mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt 300 mm long not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Stainless Steel (304 Grade) finished, floor Door Stooper, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding etc for fixing to MS frame complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided forcomplete all as specified and directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings,balconies, canopies,deck slabs and in shelves and the like.complete all as specified and directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in chajjas complete all as specified and directed by Engineer-in-Charge.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing, chajja and similar work not exceeding 200mm thick (Horizontal or slopping) for rough finished suface of concrete complete all as specified and directed by Engineer-in-Charge.

Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers ,lintels, cantilevers,shelves, chajja including supports overhangs etc. also splays between floors and beams etc for rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge.

Material and labour for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Material and labour for Mild steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position complete all as specified and directed by Engineer-in-Charge.

Material and labour for cement concrete 1:7:12 mix, type F-2 (using 40mm graded Brick aggregates) as in filling of sunken portion complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 15 mm thick on brick or concrete surfaces of wall of sunken portion in cement mortar 1:3 mixed with Liquid water proofing compound as per manufacturers instructions, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: Liquid WPC shall be measured and paid separately

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) and applying bitumen 85/25 grade @ 0.1.20kg/sqm over 0.30 kg/sqm bitumen primer and landed APP membrane on primed surface by Torch application complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sunken floor complete all as specified and as directed by Engineer-in-Charge.

Dismantling of brick or terracing tiles of single layers on roofs and removed from site complete all as specified and as directed by Engineer-in-Charge.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thicknes removed or only a part thereof) and removing the demolished material out of MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for wire brushing and cleaning top surface of RCC roof including flashings and junction of parapets, etc.complete all as specified and as directed by Engineer-in-Charge.

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete 1:2:4 type B1 (using 12.5mm graded stone aggregate) as in roof kerbs, mud stops,steps small sumps and like items slightly rounded or chamfered on the edges complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete 1:3:6, type C-0 using 12.5mm graded stone aggregates as in padding over roof, minimum thickness at khurra as 45 mm to maintain a slope of 1:100 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for PCC tiles 25cmx25cmx20 mm thick laid over cement mortar 1:3 mixed with liquid water proofing compound as per manufacturers instructions and joints grouted flush in cement mortat (1:3) complete all as speciied and directed by Engineer-in-charge. Note : Liquid WPC will be measured and paid for seprately.

Material and labour for forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A',complete all as speciied and directed by Engineer-in-charge.

Supply and fixing 25 mm bore dia GI pipe medium grade as spouts 60 cm long complete all as speciied and directed by Engineer-in-charge.

Supply and fixing in repair stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete including 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etccomplete all as speciied and directed by Engineer-in-charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Supply and fixing in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete complete all as speciied and directed by Engineer-in-charge.

Supply and fixing in repair stainless steel sink with drainage board 1.00 mm thick, glossy finish, for kitchen with plugs washers and waste coupling of 32mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 915mm x460/928mmx458mm with bowl size 410x 355x185mm/430x355x200 with wall connection pipe & wall flange and making good disturbed portion in CM 1:3 or PCC 1:2:4 complete all as speciied and directed by Engineer-in-charge.

Material and labour for cement concrete type C-2, (1:3:6) using 40mm graded stone agrregate as in foundation ,filling, mass concrete, sub base etc complete all as specified and directed by Engr-in-Charge.

Material and labour for Granite 15-18 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms, laid over and including 15 mm thick screed in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Baroda green marble, 15-18 mm thick, (table rubbed and polished) machine cut, laid over & including 15 mm thick (average thickness) cement mortar (1:3) screed and bedded, jointed with grey cement slurry & pointed with grout of matching shade including rubbing and polishing (Granite finish), over cooking platform shelves , RCC counters, window cills & similar situations complete all as specified and as directed by Engineer-in-Charge.

Material and labour for baroda green marble, 15-18 mm thick, (table rubbed and polished) machine cut,, set and jointed in cement slurry over & including screed of 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Rounding to edges of stone (of any description) slabs one edge, such as in steps, cooking platform, and other similar situations including cutting, rubbing and polishing (mirror finish), complete all as specified and as directed by Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including CM(bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Non - skid Ceramic tiles 7 to 8 mm thick polished, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc over and including 15 mm thick rendering in cement mortar 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete all as specified and as directed by Engineer-in-Charge.

Material and labour for ceramic glossy finish, joint free premium quality coloured tiles 600 x 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by Engineer-in-Charge. Note : Dado should be flushed with the wall plastering.

Material and labour for anti-skid premium quality coloured tiles 400 X 400 mm and 7-8 mm thick, as in floors, steps, cills etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair chromium plated brass overhead shower 125mm dia with 235mm long shower arm and incl all necessary accessories as recommended by manufacturer for fixingcomplete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 15 mm dia chromium plated long body Bib Tap cast copper alloy fancy type long body CP with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, non telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair brass chromium plated mixer for WHB for mixing hot and cold water screwed down for 15mm dia iron pipe complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Concealed Stop Cock, fancy type, CP with long shank and cup, exposed part kit with wall flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair single lever Sink mixer with swinging spout with connecting legs and wall flanges, wall mounted fency type chromium plated cast copper alloy screwed down high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Vitreous China wash down pedestal pattern EWC, white water closet pan with intergral trap including seat cover ,making necessary connections to drain and to flushing pipe antisyphonage pipe etc, jointing to UPVC/PVC/CI and flush pipe including making good to floor complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair vitreous china premium/1st quality wash basin , white/ivory/off white, flat back, size 550x400 mm screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and completein all respect as per manufacturer's instructions.including 32 mm dia PVC pipe upto floor trapinserted in wall and making good on disturbed surfaces complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PTMT Jet Spray with 1.5 metre long flexible tube including making connections and fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair doubled layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) 500 Ltrs capacity hoisted and fixed in position all as specified including ball brass valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect CPVC to PVC tank complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair CPVC, globe or gate valves, with iron wheel head, screwed both ends for 20 mm bore CPVC pipe complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair CPVC, globe or gate valves, with iron wheel head, screwed both ends for 25 mm bore CPVC pipe complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair PVC connections 15mm size with PTMT nuts of length 450 mm ccomplete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair PTMT grating 150x150 mm size square shaped with cockroach trap for floor trap fixed in position complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing in repair PVC(HDPE) SWR , 75 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, fixed to walls complete all as specified including fixing of pipe to wall with flat iron clamps of size 25 x 3mm, bolts washing, nuts etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm bore UPVC soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors and making necessary connections complete all as specified including dismantling of old pipe and excavation of trenches, refilling and leveling of surface complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC(SWR) bends (any radius), for 75mm bore pipes, with access doors,complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC(SWR) bends (any radius), for 110mm bore pipes, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) junction double,(double T), equal or unequal with access door for 110 mm bore complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) junction double,(double T), equal or unequal with access door for 75 mm bore complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair PVC (SWR) bends/tees of any radius for 110mm bore with access door as complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 110mm dia bore UPVC soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors and making necessary connections complete all as specified incl dismantling of olzd pipe and excavation of trenches,refilling and leveling of surface complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC(HDPE) SWR , 110 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction fixed to walls complete all as specified including fixing of pipe to wall with flat iron clamps of size 25 x 3mm, bolts washing, nuts etc as including taking down existing damaged CI waste water pipe/rain water pipe complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair UPVC floor trap 100mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair PVC bend duck foot or heelrest, radius for 100mm bore pipe, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC nahani trap including jointing to waste pipe in neat cement 100mm dia fixed in cement concrete (1:2:4) type B1 complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC cowl of 75mm dia bore complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing PVC cowl of 110mm dia bore complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in position PVC (SWR) gully trap type 'P' 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair 40mm dia bore PVC (HDPE) SWR pipes single socketed in any length with rubber ring joints using solvent cement joints,fixed on wall or laid in floors and including elbow, tee, socket, bends etc. and making necessary connections complete all as specified and as directed by Engineer-in-Charge. .

Demolition of brick work or stone/boulder masonary including all quoins,arches,pillars etc built in cement mortor complete all as specified and as directed by Engineer-in-Charge.

Material and labur for brick work using sub class 'B' bricks staight or curved on plan exc 6.0 m mean raidus built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-Charge.

Material and labur for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, base for tanks etc 50 mm thick, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints complete all as specified and as directed by Engineer-in-Charge.

Material and labur for cement concrete 1:3:6 type C-2 using 40mm graded stone aggretgate, as in base for PVC tanks, as in sub base of floors and other similar items complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25mm thick cement concrete type B0 1:2:4 (using12.5mm graded stone aggregate) as in floor finished rough to recieve floor finishes etc complete all as specified and as directed by Engineer-in-Charge.

Material and labur for 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes/tiles complete all as specified and as directed by Engineer-in-Charge.

Taking up or down existing steel tubing 15mm bore and connections and removing from site complete all as specified and as directed by Engineer-in-Charge.

Taking up or down existing steel tubing 20 mm bore and connections and removing from site complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying of 20mm outer dia CPVC pipes SDR11 with including all brass CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and as directed.

Supplying and laying of 25mm outer dia CPVC pipes SDR11 with including all brass CPVC SDR 11 fittings on walls / ceiling or laying in floors complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed Conduit(TV/Tele Socket) etc. and making good, cutting not exc 10cm girth and complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing stainless Steel peg set of 6 hooks and including all accessories like screws etc as recommended by manufacturer fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing acrylic glass shelf assembly for soap dish and appropriate space for placing other things like tooth brushes comb tooth paste etc and fixed to walls with plug and brass chromium plated screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Stainless steel plate rack made out of 1 mm thick stainless steel sheet of size 600x600x250mm fixed to wall with PVC plugs, screws etc complete all as specified and as directed by Engineer-in-Charge. .

Material and labour for MS work of Fe-290 (Grade E-165) grade including connected plates etc as in frame work for Cooler stand/ railing/ roofs/sheds/chajjas etc and like items including necessary welding/fixing etc complete all as specified and as directed by Engineer-in-Charge. .

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing18 mm thick with minimum density 600 Kg/cu.m LEAD FREE WPC board, ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing 18 mm thick with min density 600 Kg/cu.m LEAD FREE WPC board of single side rigid laminate of approved colour and other side plain white colour fixed with SS screws anD solvent cement/ adhesive to make kitchen/bed rooms cabinet shutters and shelves as per manufacturer’s instructions complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing 5 mm thick with min density 600 Kg/cu.m LEAD FREE WPC board of single side rigid laminate of approved colour and other side plain white colour and pasted with solvent cement/ adhesive on frame work of cup boards as per manufacturer’s instructions complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing stainless steel /continuous (Piano) hinge width of flaps( when open) 19 mm complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing Stainlless Steel 304 garde Basket cutlery of size 370x485 mm premium quality complete fixed in position complete all as specified and as directed by Engineer-in-Charge. .

Supply and fixing Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required size complete fixed in position complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Wardrobe tube/ hanging rod for CB of size 30x15 mm and 0.6 mm thick stainless steel 304 grade rectangular high gloss finish complete fixed in position incl s&f brackets/screws etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made extruded aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters ccomplete all as specified and as directed by Engineer-in-Charge. including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf and incl hook and eye. Note: complete shutter window will be treated as single uit and paid as single unit

Supply and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made aluminium 50 micron powder coated grill, opening size 101.6X63.5 mm (4''X2.5'') and of apporox weight @1.345 Kg/Sqm fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge..

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/exhaust/bell point all as specified and directed by Engr-in-Charge. Note : (i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost (ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.(iii) Neccessary cutting chasing wherever required and making good the disturbed surface shall be part of job at no extra cost.(iv) in ceiling Portion surface conduit wiring to be done. Make of Cable: Havells /Polycab/Anchor, Make of PVC conduit - Kalinga/Polycab/PCG/AKG.

All as per item No 133 here-in-before but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 133 here-in-before but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 133 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Modular Socket 6A/16A - 2/3 pin 2 module type complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing Modular Socket, 6A - 5 pin 2 module type complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing Modular switch 1 way 6A, 1module type complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing Modular switch 1 way 16A, 1 module type complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing Modular Bell push 6A 1 module complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing modular type fan step regulator, 120W - 1 module complete all as specified and as directed by Engineer-in-Charge.Make: Havells / Anchor /Legrand/Indoasian

Supply and fixing ceiling rose modular type , surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed by the Engineer-in-Charge.Make: Havells/cona/ssk

Supply and fixing in replacement of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 8 way double door type with 200 amp rated bus bar complete all specified and as directed by the Engineer-in-Charge.. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The DB shall be fiush fixed and making good the disturbed surface shall be part of job at no extra cost. Make :- Lrgrand/Havells/L&T

Supply and fixing in replacement of MCB SP up to 6-32 Amp complete all specified and as directed by the Engineer-in-Charge.. Make :- Lrgrand/Havells/L&T

Supply and fix in replacement of MCB SPN 6-32 Amp complete all specified and as directed by the Engineer-in-Charge. Make :- Lrgrand/Havells/L&T

Supply and fixing in replacement of old unserviceable LED tube light fitting 1x20 Watt industrial batten type with bipin holders connector block complete with all accessories internally prewired and incl connecting up three core single wire incl 01 no. 20 watt retrofit LED tube rod T8 polycabonate complete all specified and as directed by the Engineer-in-Charge.. Make : Havells/Philips/Bajaj

Supply and fixingmodular type lamp holder, PVC/ polycarbonate type with back plate suitable for 7 to 18 watts for batten fitting complete all specified and as directed by the Engineer-in-Charge.. Make : Havells/Anchor/Bajaj

Supply and fixing LED Lamp 9 watt inverter type complete all specified and as directed by the Engineer-in-Charge.Make : Havells/Philips/Bajaj

Supply and fixing call bell ding dong AC 230 volt single pole complete all specified and as directed by the Engineer-in-Charge. Make : Havells/Philips/Bajaj

Supply and fixing in replacement environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit led luminaire comprising of high brightness leds of capacity10 Watt complete all specified and as directed by the Engineer-in-Charge. Make : C&S/philips/Havells

Supply and fixing LED mirror light ultra slim with extruded polycarbonate , environmental friendly,energy efficient of capacity 10 watt complete all specified and as directed by the Engineer-in-Charge. Make : Havells /C&S/Philips

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all specified and as directed by the Engineer-in-Charge. Make: - Havells/Bajaj/Crompton. Note:- Old u/s C/Fan to be deposited in MES store.

Supply and fixing exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all specified and as directed by the Engineer-in-Charge. Make : CG/Havells/Usha Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt , making hole in wall for groutng and making good the disturbed surface including plaster work shall be part of job at no extra cost.

Supply and fixing exhaust fans AC single phase 230/ 240 V of size 230 mm sweep with louver complete all specified and as directed by the Engineer-in-Charge.. Make : CG/Havells/Usha Note: Fixing of Exhaust Fan on wall with suitable size anchor bolt , making hole in wall for groutng and making good the disturbed surface including plaster work shall be part of job at no extra cost.

Supply and fixing new generation energy saving and environmental friendly long life LED building security light 1x25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bemd to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all specified and as directed by the Engineer-in-Charge. Make : Havells/Philips/Bajaj

Supply and fixing in replacement sheet metal enclosures distribution boards, double door three phase 415 volts VTPN 4 ways (one incoming three phase & four out goings three phase )for MCCB, comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a)MCCB FOUR POLE 100 AMPS AC 415 VOLTS 16 KA =01 NO as incoming (Note :- (i)The DB shall be VTPN (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(iv) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly with digre of protection IP 54 complete all as specified and directed by Engr-in-Charge. Make :- Havells/LEgrand/L&T

Supply and fixing/laying in replacement of existing unserviceable XLPE insulated, armoured heavy dutyelectric cable with aluminium conductor, 1100 volt grade of crosssectional area 25 Sqmm 3 & 1/2 Core complete all specified and as directed by the Engineer-in-Charge. Make :- Havells/Polycab/Finolex

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of Pipes, cables, poles,Stay and strips etc and getting out as in soft/loose soil complete all specified and as directed by the Engineer-in-Charge.

Returning, filling-in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all specified and as directed by the Engineer-in-Charge.

Removing excavated material to a distance not exceeding 50m and depositing where directed at a level of not exceeding 1.5m above the starting point complete all specified and as directed by the Engineer-in-Charge..

Material and labour for laying old size well burnt brick, laid flat, perpendicular to the direction of cable for cable protection complete all specified and as directed by the Engineer-in-Charge.

Material and labour for laying fine sand in trenches, 8 cm below the cable and 15 cm above the cable as cushioning to cables for protection of cable complete all specified and as directed by the Engineer-in-Charge.

Material and labour for replacement of GI tubing light grade 40 mm bore for passing through cables under the floor ,along the wall or along the pole complete all specified and as directed by the Engineer-in-Charge.

Material and labour for earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4 mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15 cm all around the plate all as specified and shown in EP-3 of SSR Part-I complete all specified and as directed by the Engineer-in-Charge.

Please Enable Macros to View BoQ information