SPECIAL REPAIRS TO BLDG No. 18 OF 115 INF BN TA MAHAR, SPECIAL REPAIRS TO BLDG No. T 57 AND T 59 OF HQ JL WING THE INF SCHOOL AND PROVISION OF TOILET BLOCK NEAR BLDG No. E2A AND E2B AT 115 INF BN TA UNDER GE BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC block masonry built in cement mortar or lime cement mortar in any position below or above ground level all as specified and directed.

Cutting, chases for concealed water tubing and making good in CM 1:3 cutting not exceeding 10 cm girth in brick wall all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any position, in un-framed work all as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section all as specified and directed.

Dismantling of battens for tiles, shingles etc, of any size spacing exceeding 15cm including tilting fillets in roofing all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area n exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed.

Dismantling of plain or corrugated steel sheets of any gauge and thickness, in roof coverings, valleys, gutters, etc. all as specified and as directed.

Dismantling wall or ceiling boards or insulation boards/ slabs of any thickness including cover fillets all as specified and as directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Taking up or down existing unserviceable 15/ 20mm bore steel/ PVC pipes of any grade alongwith all fittings and making good disturbed surfaces all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in soft/ loose soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/dense soil all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread, levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D2, using 40mm graded stone aggregate in foundation filling and mass concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10cm width, blocks cast in PCC 1:3:6 type C0, using 12.5mm graded stone aggregate, set in CM 1:6 complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, type B-0, using 12.5mm graded stone aggregate mixed with water proofing compound as in damp proof course to horizontal or vertical surfaces including use of necessary form work all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed blocks, benching in channels, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for extra for forming fair finished drain or channel of 25cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slabs, spacer bands, curbs, etc. with plain fair faces, set in cement mortar 1:4 all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in columns, pillars, piers, posts and struts all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in beams, cantilevers, lintels, lintel bands all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix using 20mm graded stone aggregate in chajja or similar items all as specified and directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed.

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to sides and soffits of roof beams, tie beams, lintels, and similar works for rough finished flat concrete surfaces all as specified and directed.

M&L for use of form work to sides and soffits of chajjas, flat rough finished surfaces of concrete all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work all as specified and directed.

Fixing only serviceable timber scantling of any description obtained from dismantling in un-framed work all as specified and directed.

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, wrought, secured with nails or beads; sectional area exc 13 and n.exc 25 sq.cm all as specified and directed.

Fixing only serviceable timber fillets of any description obtained from dismantling secured with nails or beads; sectional area exc 13 and n.exc 25 sq.cm all as specified and directed.

M&L for powder coated aluminium frame work as in doors, partitions and windows using standard aluminium extruded sections with thickness of powder coating not less than 50 microns including provision of glazing clips, hinges, handles, etc all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels shall be measured and paid separately.

M&L for aluminium sliding windows (Triple track), fabricated to required size with powder coated aluminium sections, with bottom track of size 92 x 31.75 x 1.6mm, side and top frame of size 92 x 31.75 x 1.4mm, top and bottom shutter rail of size 39x17x1.4mm, outer style of size 39 x 17 x 1.4mm, interlock style of size 39 x 27 x 1.4mm, including provision of 5mm sheet glass ordinary quality and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm for panels including provision of all hardware fittings such as handles, locking arrangements, rubber gaskets, rollers, spring catchers etc. complete all as specified and directed. Note: Each window shall be provided with 2 glazed shutter & one wire mesh shutter

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel tower bolt, hold fasts, complete with glazing bars, dovetailed or welded all as specified and as directed.

S&F Steel ventilators with top hung shutters including hinges with steel peg stays, hold fasts, complete all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on single side reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F stainless steel butt hinges 100mm in size, medium weight all as specified and directed.

S&F aluminium anodised barrel tower bolt 150mm size all as specified and directed.

S&F 150 mm long extruded section aluminium alloy anodised handles fabricated type all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm fixed in floors complete all as specified and as directed.

S&F Door closer, of aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of weight between 61 to 80kg, all as specified and directed

S &F Mortice lock, vertical type, size 100 mm, 4 levers complete all as specified and as directed.

S&F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.complete all as specified and as directed.

S&F brass finials, fancy type, 40mm dia, suitable for curtain rods fixed with nut and screw and washer all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 58 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde- E- 250) quality-A complete all as specified and as directed.

M&L for mild steel flats for wind ties for roof including securing bolts and similar works, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roof covering/ claddings to wall, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F plain galvanised mild steel sheeting with grade of zinc coating 275, 0.8mm thick, in ridges, hips, valley gutter, drip and straight flashings all as specified and directed.

M&L for cement concrete roofing tiles, rustic red/ cloud grey, 420 x 330mm size, 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry all as specified and as directed. Make: ETERNA model of INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete ridge/ hip cap tiles to suit rustic red/ cloud grey concrete roofing tiles, 330 x 207/249mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete hip starter tiles to suit rustic red/ cloud grey concrete roofing tiles, 360 x 210mm size, minimum 17mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

M&L for concrete 3 way cap tiles to suit rustic red/ cloud grey concrete roofing tiles, 351 x 429mm size, minimum 15mm thick, bedded and jointed in CM 1:6 all as specified and directed. Make: INDOGRACE or PIONNIER or equivalent approved make.

S&F PVC (SWR) eaves gutter square/ trapezoidal profile 150mm bore including pipe accessories PVC holder bats bolts nuts etc. including taking down existing unserviceable gutters of any description and size and making good disturbed surfaces all as specified and directed.

M&L for 3mm thick Aluminium Composite Panel comprising of a core containing not less than 70% non combustible mineral filling sandwiched between two skins of 0.5mm thick aluminium alloy PERALUMAN-100 (AlMg1-NS41) complete with all necessary sub-structures, anchors, hardware and fittings to provide a total installation, fixed to existing wooden/ steel members all as per manufacturers instructions, all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc. Make: Alstrong/ Aludecor/ Alucobond/ Eurobond

S&F solid wall lining consists of 5mm thick wood grain printed PVC sheet inclusive of solvent cement fixed on and including provision of 5mm thick PVC fillet of size 35mm wide fixed at 300mm c/c including necessary PVC strips as required etc complete all as specified and as directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminum anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling all as specified and directed.

S&F suspended false ceiling system with 16mm thick mineral fibre acoustical MINA TUFF EDGE TILES (MIRO LOCK), white, fibre performance class-I (BS 456, Part 6&7), with bio coating on the exposed face of tiles, module size 600x600mm, laid on 15 mm thick SILHOUTTE EXPOSED GRID system, with minimum load carrying of 11.68 Kg/Sqm, white/black colour all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 50mm thick plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base for flooring including finishing the surface even and fair all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in paving/ hard standing/ floor laid in alternate bays and finishing the concrete surface even and smooth without using extra cement and making impressions of expanded metal while the concrete is green all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 9 to 10mm thick, area of each tile not exc 0.36 Sqm, as in floors/ skirtings, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for coloured non skid ceramic tiles, edge cut, 6 to 7mm thick area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured joint free non skid ceramic tiles, edge cut, 7 to 8mm thick area of each tile exc 0.11 Sqm but not exc 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for coloured glazed ceramic tiles 350mm x 450m or 250mm x 350mm size, 7mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:6 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in partitions, platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for grinding and polishing the existing old Kota stone flooring/ skirting with necessary white cement, marble powder including treating the surface with Bee wax polish etc. complete all as specified and directed.

M&L for coloured polished designer cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, machine pressed, set, jointed and pointed in neat cement slurry, as in pathways, pavings, etc., laid over and including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for 80mm thick machine pressed precast concrete interlocking paver blocks with grey cement and pigments, M-40 grade, any shape and size with anti skid finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for 55-60mm thick machine pressed precast concrete interlocking coloured paver blocks, M-35 grade, any shape and size with glossy finish on top confirming to IS 15658-2006 all as specified and directed.

M&L for crushed stone sand (M-sand/ Robo sand/ I-sand) as in cushioning for interlocking paver blocks including watering and consolidating complete all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C1, using 20 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on stone masonry or other than fair faces of brick work finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair faces of brick work, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound on fair faces of brick work or block masonry or concrete surfaces of sump well finished even and smooth without using extra cement all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane, all as specified and directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane, fixed in repairs, all as specified and directed.

M&L for 4mm thick sheet glass ordinary quality and glazing to aluminium joineries in square not exc 0.5 sqm in each pane all as specified and directed.

M&L for 5mm thick sheet glass ordinary quality and glazing to aluminium joineries in square exc 0.5 sqm in each pane all as specified and directed.

M&L for three coats of white wash on newly plastered walls, pilasters, cornices, etc. including necessary preparation of surfaces all as specified and directed.

M&L for two coats of oil bound distemper any colour, over a coat of primer over 1mm thick layer of wall care putty, on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper, any colour, over a coat of primer over 3mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, over a coat of alkali resistant primer on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for preparation of new steel surfaces not exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for 1000 litres capacity rotational moulded polyethylene (HDPE) water storage tanks, 'ISI' marked, cylindrical, vertical with closed top conforming to IS 12701-1989 having two layers wall construction with manhole lid and suitable locking arrangement including making holes for inlet, outlet and over flow pipes, hoisted and fixed in position including testing complete all as specified and directed.

S&F 20mm dia PTMT ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed.

S&F 25mm bore gun metal gate valve heavy duty ISI marked with iron wheel head screwed both ends to iron pipes and fixed all as specified and as directed

M&L for 15 mm bore UPVC water supply pipes, 10kgf/ sqcm, including all fittings such as elbow, reducer, tee, couplers, short pieces, connectors etc. fixed to walls, ceilings with PVC batten holders, all as specified and as directed.

All as described in item No. 115 but 20mm bore UPVC pipes

All as described in item No. 115 but 25mm bore UPVC pipes

S&F 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15mm bore bib taps, fancy type, brass CP, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed. Make: Cat No. CON 107 KN of JAQUAR or equivalent model in ESS ESS/ JOHNSON/ CERA

S&F 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs 15 mm bore 2 way Bib tap, long body, brass chromium plated, fancy type, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed. Make: Cat No. FUS 29041 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. ALD-CHR 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F 15mm bore stop valves, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore angle stop valves, brass chromium plated, high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F vitreous china wash basin, white, size 550x400mm, including CI brackets and cutting for and pinning in ends of brackets or erecting stands etc. all as specified and directed.

S&F in repairs Vitreous China wash basin, any colour, oval type, size 630x450mm, including provision of vitreous china pedestal fancy type swan neck type pillar tap, waste coupling and waste pipe including cutting for and pinning in ends of brackets etc complete all as specified and directed. Make: Cat No-1022 CONCORD MODEL of CERA or equivalent in Parryware/ Neycer/ Hindware

S&F Vitreous China urinal, bowl type (back or corner wall type), white, 465mm x 355mm x 265mm size, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F in repairs Vitreous China urinal, half stall type, white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, (excluding flushing cistern, flush pipe) all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F vitreous china squatting pan, Orissa pattern, size 580mm x 440mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap including provision of lime concrete bedding etc complete all as specified and directed.

S&F in repairs cascade type vitreous china wash down water closet pan (pedestal pattern), white, coupled with flushing cistern including 'P' or 'S' trap, seat and cover, fixing bolts etc, connecting to drain pipe and flushing pipe all as specified and as directed.

S&F in repairs bass chromium plated toilet paper holder fixed to wall with wooden plugs, chromium plated brass screws and cup washers all as specified and as directed. Make: Cat No. 1151N of JAQUAR or equivalent model in JOHNSON/ ESS ESS/ ARK

S&F syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), suitable for urinals all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, 600mm long all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs vitreous China soap dish, white, approximate size 160x 160x90mm, any type, fixed to plugs with chromium plated brass screws all as specified and as directed.

S&F brass chromium plated tubular towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs fancy type towel rod, brass CP, 600mm long, fixed to wall with plugs and chromium plated screws all as specified and as directed. Make: CAT No. CAN-CHR- 1111N of JAQUAR or equivalent model in JOHNSON/ ESS ESS/ CERA

S&F UPVC PVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F UPVC (SWR) gully trap 125/110mm alongwith PVC grating, setting & jointing with solvent cement all as specified and as directed

S&F 110mm bore UPVC (SWR) vent cowl all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) pipes, single socketed, in any length, with solvent cement joints, fixed to wall or laid trenches or in floors, all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius all as specified and directed.

M&L for 150mm bore Salt glazed stoneware drain pipes, grade 'A', laid in trenches and jointed as specified all as specified and directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all s specified and as directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, bell pushes, ceiling roses, pendants, regulators, sockets, bells, holders, light fittings, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC conduit/ PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 1/2 module PVC surface mounting box with standard white modular cover plate & frames for mounting modular type switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 158 but for one fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 158 but for one bell point controlled by one bell push

All as described in item No. 158 but for one 05 Amps socket outlet on independent board.

All as described in item No. 158 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 158 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F modular switch, 1 module, 1 way, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular switch, 1 module, 1 way, 16 Amps 230 volts, AC, all as specified and directed.

S&F modular bell push, 1 module, 6 Amps, 230 volts, AC, all as specified and directed.

S&F modular socket outlet, 2 module, 6 Amps 2 cum 3 pin multipurpose all as specified and directed.

S&F modular socket outlet, 2 module, 2 pin 6A/ 3 pin 16 Amps, multipurpose all as specified and directed.

S&F fan regulator electronic modular step type, 2 module, suitable for 1200/1400mm sweep ceiling fan all as specified and directed.

S&F call bell, ding dong 230 volts AC supply all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 34 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 34 W high brightness SMD LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2x2 or equivalent in CG/ Philips/ Wipro

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP66 protection, 6000K and impact resistance IK07, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F decorative 25Watts energy saving LED post-top lantern, with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source. with all accessories including 25 Watts 5700K LEDs complete with electronic driver and all accessories fixed in position including provision of suitable size PVC insulated multistranded copper conductor cable from junction box to light fitting and connecting up and testing including provision of suitable size medium grade GI pipe fixed on top of pillar all as specified and as directed. Make :- HAVELLS RUBY CLEAR or equivalent in CG/ Philips/ Wipro

S&F Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F in repairs Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F MCCB VTPN DB 12 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F in repairs, MCCB VTPN DB 12 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCCB TP 125 Amps ,25KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F MCB DP 63A 'C' series 10KA 50Hz 240 Volts AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 3 blades, Star rating with all accessories complete including taking down existing unserviceable ceiling fan of any description and size from the location and setting aside for fixing/depositing to MES E/M store all as specified and as directed. Make: HAVELLS Model No. ES-50 or equivalent model in Crompton Greaves/ USHA

S&F in repairs 3 core flexible copper conductor cable of size 0.5 sqmm, 1100 volts grade, connecting from ceiling rose to connector block of fan all as specified and as directed.

M&L for 50mm dia GI pipe medium grade cut to required length as per site requirement and fixed into walls in single piece without any joints as in supports for hanging of ceiling fans complete all as specified and directed.

S&F in repairs exhaust fan, 230mm sweep, 230/240 Volts, 1350 RPM, single phase, metallic finish powder coated, with wire grid protection and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells VENTL-AIR DSP model or equivalent model in Almonard/ Crompton Greaves

S&F exhaust fan, 250mm sweep, 230/240 Volts, 1350 RPM, single phase, PVC body with louvres and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells VENTL-AIR DX model or equivalent model in Almonard/ Crompton Greaves

S&F storage type water heater (Geyser), vertical type, 25 litres capacity, 2000/1500 Watts, Star rating including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers and provision of 2 Nos of 600mm long x 15mm bore PVC connection pipe, connecting up electrical & water supply lines, testing complete all as specified and as directed. Make: MONZA EC model of HAVELLS or equivalent model in RACOLD/ BAJAJ

M&L for XLPE insulated, armoured, heavy duty electric LT UG cable with multi-stranded aluminium conductor, 1100 Volts grade, cross sectional area 35 Sqmm x 3.5 core, laid in trenches/ passing through pipe/ duct or fixed to wall including provision of necessary lugs/ thimbles/ ferrules, connecting up , testing and commissioning complete laid in repairs all as specified and as directed. Note: Excavation, earth work, cable cushioning, bricks/ GI pipe for protection shall be measured and paid separately under relevant items of this schedule.

All as described in item No. 193 but LT UG cable of size 35 sqmm x 4 core

M&L for double wall corrugated HDPE pipes, conforming to IS 14930-2001, ISI marked, 63mm outer dia, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches/ under roads/ crossing etc. all as specified and as directed.

M&L for GI tubes, light grade, 50mm bore, as in cable protection, fixed to poles/ walls with necessary MS clamps, bolts, nuts, washers or laid in trenches / under roads/ crossing etc. all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

Vinod Enterprises

SAMARTH ASSOCIATES

M/S MAHADEV M PATIL

ASHOK M RAJGOLKAR

M/s. N D KALING

M/s.Y.N.PATIL

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS