REPAIR MAINTENANCE AND OVERHAULING OF LIFT, EOT CRANE, MECHANICAL LAUNDRY AND OTHER EM ITEMS UNDER GE I GOS

Amount

Comprehensive maintenance and repairs of Mechanical laundry consisting of following items (Spares/items mentioned herein after shall be paid seperately. Cost of any other spares not included in items herein after shall be borne by the contractor):- Items covered for preventive and breakdown maintenance are:- (i) Industrial Water Extractor Model NXS15 – 1 No. (ii) Industrial Water Extractor ModelNXS30 – 2 Nos (iii) Industrial Drying Tumbler Model DRS 30- 1 No. (iv) Flat bed Drying Press Model FPS150 (v) Air compressor – 1 No.

Sypply and fix in repair for hose pipe for drain straight 3" for AXE 15 complete all as specified and directed.

Supply and fix in repair for over flow pipe 1.25" for AXE 15 complete all as specified and directed.

Supply and fix in repair for drain L shape 3" for AXE 15 complete all as specified and directed.

Supply and fix in repair for operating computer ST-9 for AXE 15 complete all as specified and directed.

Supply and fix in repair for hose pipe for drain straight 3" for AXE 30 complete all as specified and directed.

Supply and fix in repair for coil with core for drain vlave for AXE 30 complete all as specified and directed.

Supply and fix in repair for control relay for AXE 30 complete all as specified and directed.

Supply and fix in repair for relay with base for AXE 30 complete all as specified and directed.

Supply and fix in repair for electric heater for AXE 30 complete all as specified and directed.

Supply and fix in repair for V belt B 98r for AXE 30 complete all as specified and directed.

Supply and fix in repair for door lock electromagnetic for AXE 30 complete all as specified and directed.

Supply and fix in repair for heater for DRE 30 complete all as specified and directed.

Supply and fix in repair for forward reversing timer for DRE 30 complete all as specified and directed.

Supply and fix in repair for V belt A 87 for DRE 30 complete all as specified and directed.

Supply and fix in repair for V belt B 65 for DRE 30 complete all as specified and directed.

Supply and fix in repair for hose clamp for DRE 30 complete all as specified and directed.

Supply and fix in repair of solenoid cut off switch complete as specified and as directed

Supply and fix in repair of push button start stop type complete as specified and as directed

Supply and fix in repair of Nozzle 4 mm and as per existing sample complete as specified and as directed

Supply and fix in repair of Checking and thoroughly cleaning of steam supply MS Pipe line to all equipments connection and point complete all as specified and as directed. Note: overhauling asbestos rope and aluminium foil paper etc. Are included in the unit rate quoted.

Supply and fix in repair of steam line control valve as per existing sample complete all as specified and as directed.

M&L for cleaning of Air compressor Machine air line and air storage tank as per existing sample complete all as specified and as directed.

Supply and fix in repair of pressure release valve per existing sample complete all as specified and as directed.

Supply and fix in repair of double function type bearing for washer extractor or drying tumbler of capacity of 30 Kgs including all fitting and fixture washer nut,bolts complete all as specified and as directed

Supply and fix in repair Vibrator bush as per existing sample complete all as specified and as directed

Supply and fix in repair of hydraulic type jack oil SAE-90 super cleaning of complete hydraulic pressure (Refilling of oil and sealed with oil cap) completer all as specified and as directed

Comprehensive maintenance and repairs of electrically operated overhead travelling cranes (EOT) consisting of main girder, cross travel, hoist crab, carriage, long travel drive mechanism, long and cross travel wheel pinions, bearings, rope drum, gear boxes, motors, wire rope, limit switches, overload and time delay relays/resistors, bottom control panels, contactors 3 pole, pendant push button suspension mechanism, etc complete of the following capacities (Spares/items mentioned herein after shall be paid seperately. Cost of any other spares not included in items herein after shall be borne by the contractor):- ( a) EOT Crane 1 Ton to 3 Ton Capacity

Rewinding of 3 phase 415 Volts electric motor of main hoist, creep hoist, long traverse and cross traverse of following capacity with super enamelled copper conductor of gauge as per the existing for the following:- (a) Electric motor above 1 HP but upto and including 5 HP.

Supply only MCB SP 6 to 32 Amps, 240V for of EOT crane. (Make: Schnider Eletric, Havell's, indo asian, L&T)

All as per item no. 30 but MCB two pole 16 to 32 Amps, 240V (Make: Schnider Eletric, Havell's, indo asian, L&T)

All as per item no. 30 but MCB triple pole 16 To 32 Amps, 240 V (Make : Schnider Eletric,, Havell's, indo asian, L&T)

All as per item no. 30 but MCB triple pole and neutral 32 to 63 Amps, 240 V (MakeSchnider Eletric,, Havell's, indo asian, L&T)

All as per item no. 30 but contactors 4 pole 25 Amps, 3Ph, 415V (Make: Schnider Eletric,, L&T, BCH)

All as per item no. 30 but contactors 4 pole 32 Amps, 3Ph, 415V, (Make: Schnider Eletric,, L&T, BCH)

All as per item no. 30 but contactors 3 pole 40 Amps, 3Ph, 415V, (Make: Schnider Eletric,, L&T, Siemens)

All as per item no. 30 but contactors 3 pole 70 Amps, 3Ph, 415V, (Make: Schnider Eletric,, L&T, Siemens)

All as per item no. 30 but overload relay 16 to 44 Amps, 415 V, (Make: Schnider Eletric,, L&T, Siemens)

All as per item no. 30 but overload relay 4-11 Amps, 415 V, (Make: Schnider Eletric,, L&T, Siemens)

All as per item no. 30 but overload relay 0 to 4 Amps, 415 V, (Make: Schnider Eletric,, L&T, Siemens)

All as per item no. 30 but Illumanated push button switch LED type with accessories (Make Schnider Electric)

All as per item no. 30 but Cable PVC insulated sheathed with copper conductor of size 4Core 2.5Sqmm with metal hose covered

All as per item no. 30 butCable PVC insulated sheathed with copper conductor of size 4Core 1.5Sqmm with metal hose covered

All as per item no. 30 but Cable PVC insulated sheathed with copper conductor of size1.5 sqmm 16 core

All as per item no. 30 but Ball bearing of Size 6208/6209. make : SKF

All as per item no. 30 but Topping up of Gear box oil 90 Grade Servo in sealed containers. (MAKE:- SERVO/CASTROL)

All as per item no. 30 but Brake Unit for 100 mm dia for EOT/HOT cranes. (Make BCH / PATHE)

All as per item no. 30 but Brake Unit for 150 mm dia for EOT/HOT cranes. (Make BCH / PATHE)

All as per item no. 30 but Steel wire rope of size 10/12 mm dia construction 6x19 Fibre core suitable for EOT/HOT cranes . Make : Usha martin

All as per item no. 30 but Limit switch 6A roller/lever type for EOT cranes(MakeJai Balagi/L&T/BCH)

All as per item no. 30 but MCB TPN 63 Amps, 415 Volts (Make- L&T/Siemens/Schnider)

All as per item no. 30 but MCB TPN 40 Amps , 415 Volts (Make- L&T/Siemens/Schnider)

All as per item no. 30 but MCB SPN 32 Amps , 415 Volts (Make- L&T/Siemens/Schnider)

All as per item no. 30 but MCB SPN 16 Amps , 415 Volts (Make- L&T/Siemens/Schnider)

All as per item no. 30 but MCB SP 6 Amps , 415 Volts (Make- L&T/Siemens/Schnider)

All as per item no. 30 but Fuse cutout 50 Amps

All as per item no. 30 but Fuse cutout 32 Amps

All as per item no. 30 but Steel Wirerope 16 Sqmm as per existing complete

All as per item no. 30 but Steel Wirerope 12 Sqmm as per existing complete

All as per item no. 30 but Steel Wirerope 10 Sqmm as per existing complete

All as per item no. 30 but Copper wire 1.5 Sqmm 10 core complete

All as per item no. 30 but Step down transformer 415-110V AC

All as per item no. 30 but Step down transformer 415-150 Volts AC

M&L for realingment of rail for EOT crane by weilding of MS plate of suitable size complete all as specified and directed by Engr-in-Charge complete. Note :- All equipment/ labour involved in this job to be provided by contractor and testing of EOT crane after repair to be done in presence of Engr-in-Charge.

Carry out load and deflection test for each EOT crane from 1 to 3 TON capacity upto 125% full load with necessary instruments on hoisting, LT/CT for checking the performance of the cranes as directed by the engineer In Charge/and upto the users safisfaction. Note: (i) Load/deflection test is to be carried out by the Govt authorized inspector to carry out test in the relevant field in presence of the department rep and recording the test and issue necessary certificate. (ii) The load required for the testing and necessary transportation, will be arranged by the contractor at the location of testing as per ground requirement.

Painting of EOT crane complete with double girder by scraping the old surface and applying one coat of primer with two coat of emulsion paint as per existing colour as per direction of Engr-in-Charge complete all as specified and directed

M&L for repair and maintence of lift 15 passenger and 1320 kg with repair of mechanical parts and attending day to day breakdown complaints/ emergency breakdown compalint after receiving phone from JE concerned. Testing of lift to be carried out every month by KONE company representative and test report in this regards to be submitted by contractor till the completion of his contract complete all as specified and directed.

Supply and fixing of energy saving environmental friendly and robust mediumbaty / highbay LED luminaire with high efficiency (100 lm/W) with toughened glass of capacity 120 watts complete all as specified and directed

M/L in replacement of 2 Runs of cable PVC insulated but unsheathed 1.5 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 1.5 Sq mm, stranded copper conductor all as specified and directed.(Cable make Anchor/Havells/Finolex) Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply testing and commissioning AC three phase ,3x 240V ,50Hz, digital,electronic tamper proof energy meter of rating 10 to 60 Amps covered with PVC transparent cover with optical communication port incl taking down the unsv meter complete all as spd & Directed.

Supply testing and commissioning AC single phase,50Hz, digital,electronic tamper proof energy meter of rating 5 to 30 Amps covered with PVC transparent cover with optical communication port incl taking down the unsv meter complete all as spd & Directed.

Routine/General check-up of DG Set Installed at various location of GMS including carrying out Monthly/Quarterly/Half yearly/Yearly preventive maintenance and servicing as per Manufactureres manual, Repair and overhauling, attending breakdown and rectification of defects with taking down u/s spares as and when required all as specified and directed by Enginner In Charge. Notes (a) Monthly/Quarterly/Half yearly/Yearly maintenance shall be carried out strictly and copy of servicing report should be submitted to Engineer In charge failing which recovery will be made at twice the quoted rates. (b) Chemicals and T & P required for cleaning and descaling and nut, bolts, washers, distilled water, shall be included in the unit rate quoated against this item. (d) Other spares which are not listed here will be measured and paid saparately under respective Items

Supply only provisional items for Oil filter suitable for 7.5 KVA to 30 KVA DG Set to be incorporated in the work against relevant items here in before for DG set of capacity 7.5KVA to 320KVA. As per existing make and type,complete all as specified and directed.

All as per item no. 74 but Oil filter suitable for 40 KVA to 82.5 KVA DG Set

All as per item no. 74 but Oil filter suitable for 100 KVA to 160 KVA DG Set

All as per item no. 74 but Oil filter suitable for 200 KVA to 320 KVA DG Set

All as per item no. 74 but Fuel filter suitable for 7.5 KVA to 30 KVA DG Set

All as per item no. 74 but Fuel filter suitable for 40 KVA to 82.5 KVA DG Set

All as per item no. 74 but Fuel filter suitable for 100 KVA to 160 KVA DG Set

All as per item no. 74 but Fuel filter suitable for 200 KVA to 320 KVA DG Set

All as per item no. 74 but Air cleaner/filter suitable for7.5 KVA to 30 KVA DG Set

All as per item no. 74 but Air cleaner/filter suitable for 40 KVA to 82.5 KVA DG Set

All as per item no. 74 but Air cleaner/filter suitable for 100 KVA to 160 KVA DG Set

All as per item no. 74 but Air cleaner/filter suitable for 200 KVA to 320 KVA DG Set

M&L for draining out oil from engine of DG set of any capacity, cleaning the oil chamber, supply and filling of lubricant in replacement GENSET OIL multi-grade 20W40 complete all as specified and directed, Make- Castrol/Gulf/Reliance

Checking and inspecting of the DG set Metering AMF panel board system throughly, including removing of the unserviceable damaged control coiling,rewiring of the same with suitable size and carried out of necessary painting matching with existing colour including tightining for all the loose contacts, reconnecting back and testing complete all as specified and directed by Engineer-in-charge.

Taking down US Digital Speed Controler & Relay Card unit complete of DG set in any capacity S&F the same as existing make and capacity all as specified and directed

Repair/replacement of door locks and hinges of DG set with welding ,denting and painting complete all as specified and directed

S & F rotating rectifier unit diode kit suitable for 7.5 KVA to 15 KVA DG set by taking out the unserviceable rectifier from excitation system and fixing and connecting, starting and testing on load all as specified and directed

Repair of Turbo charger complete of any capacity of DG set as per existing all as specified and directed

Draining the fuel from existing diesel tank in a seprate empty container and disconnecting from the DG set and cleaning fuel tank internally for removing sludge and testing to prevent the leakage if any and reconnecting the same in original position for the capacity of DG set 7.5 KVA to 30 KVA

All as per item No 92 above but 40 to 100 KVA capacity

All as per item No 92 above but 125 to 320 KVA capacity

Dismantling radiator of 7.5 to 30 KVA DG Set complete from engine mounting frame, opening and clearing with use of acid, to clear the choked tubes, over hauling of the same, arresting the leakages with soldering, replacing the gasket including replacement of water pump seal, lub oil filter, corrossion resistor filter, reefixing back the radiator in the original position, reconnecting back and testing complete all as specified and directed by Engineer-in-charge

All as per item above item No 95 but 40 to 82.5 KVA capacity

All as per item aboveitem No 95 but 100 to 320 KVA capacity

Takingdown unserviceable self-starter 12 volts from engine,dismantling and opening of stater and armature,replace the wornout carbon brush,pinion,ignition coil bearing,bushing, including servicing, varnishing of stater after repairing assembling,refixed to same position complete all as specified and directed by Engineer-in-charge

All as per serl item No.98 above but 24 volts

Dismantling and taking out unserviceable dynamo/alternator of charging unit of battery 12 volts including opening and seviceing of field coil of stator,rotor unit, replace wornout carbon brush,bushes, Bentex pinion complete all as specified and directed

All as per serl item No 100 above but 24 volts complete all as specified and directed.

Supply and replacement battery 12 Volts 180 Ah complete to DG set all as specified and directed

All as per Item No 102 above but 150 AH

All as per Item No 102 above but 100 AH

M & L for Dismantling, Lifting & transportation of Alternator of DG Set capacity 20 KVA to 82.5 KVA and keeping the core inside oven chamber to removing of moisure and increasing of the insulation value of core and drying the core assembly for minimum 3 days at a temp of 120oC including Re-fixing and alighnment all as specified and directed . Note :- (a) Cost for lifting/lowering the core of Alternator by crane is inclusive. (b) Labour for fixing the connection/removal of connection inside the heating chamber is inclusive. (c) Power consumption for heating core for improving insulation value is inclusive. (d) Temperature 120oC to be maintained and inclusive in rate quoted.

All as per item No. 105 above but 100 to 320 KVA capacity

Taking down U/S Oil lift pump repair from DG set of any make and capacity , replace new lift pump supply and fix existing make ,test and commissioning complete all as specified and directed

Taking down U/S battery charger in AMF panel for repair from DG set of any make and capacity , replace new charging unit 12volts ,supply and fix existing make ,test and commissioning complete all as specified and directed.

All as per item no.108 but 24 volts

Taking down Unserviceable power contractor and S & F 3 pole power contactor with 2 NO+2NC capacity 25 AMPs complete all as specified and directed. Make : L&T/Schineder/Simens

All as per Item No 110 above but 32 amps capacity.

All as per Item No 110 above but 40 amps capacity.

All as per Item No 110 above but 50 amps capacity.

All as per Item No 110 above but 70 amps capacity.

All as per Item No 110 above but 110 amps capacity.

All as per Item No 110 above but 185 amps capacity.

All as per Item No 110 above but 250 amps capacity.

All as per Item No 110 above but 300 amps capacity.

All as per Item No 110 above but 400 amps capacity.

Taking down Unserviceable power contractor and S & F 4 pole power contactor with 2 NO+2NC capacity 110 AMPs complete all as specified and directed. Make : L&T/Schineder

All as per Item No 120 above but 250 amps capacity.

All as per Item No 120 above but 300 amps capacity.

All as per Item No 120 above but 400 amps capacity.

S&F in replacement fan belt suitable for DG set of 7.5 to 82.5 KVA capacity complete all as specified and directed ,

All as per item 124 above but 100 to 320 KVA capacity

Taking down unserviceable AVR Unit and S & F AVR Assembly suitable for 7.5KVA to 320 KVA DG Set complete all as specified and directed.

Dismantling and Taking out unserviceable water pump assy opening and repair to unserviceable parts suitable for 7.5 KVA to 30 KVA DG Set of Make: Greeves/Kirloskar All as specified and directed.

All as per Item No 127 above but 40 KVA to 82.5 KVA DG Set

All as per Item No 127 above but 100 KVA to 200KVA DG Set

All as per Item No 127 above but 250 KVA to 320KVA DG Set

S&F in replacement of coolant suitable for DG sets complete all as specified and directed, Make - GULF / TVS / CASTROL

M/s Bapujee Builders and Traders

M/s M M Engineering Systems

M/S.J.BIJAYA KUMAR PATRO

M/S S. N. ENTERPRISES

Likitha Enterprises

M/s TECH TEAM

R J ENTERPRISES