SPL REPAIR TO OTM ACCN NO P 81/4, P 82/4, P 81/5, P 82/5, P81/6 AND P 82/6 ORS SINGLE MEMBER BARRACK OF 16 KUMAON UNDER GE SOUTH DELHI CANTT

Amount

Demolition of brick work built in cement mortar including all quions, pillars, ashlar facings, dressed stone work and precast articles etc. complete all specified and as directed.

M&L Brick work with sub class "B" bricks , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6),(up to two story Bldg) complete all specified and as directed.

M&L Brick work with sub class "B" bricks , straight or curved on in half brick thick wall built in cement mortar (1:4),(up to two story bldgs) complete all specified and as directed.

Ditto as item ser no 2 but except bricks, complete all specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site complete all specified and as directed.

Ditto as item ser no 5 above but above ground floor complete all specified and as directed.

M&L machine cut kota stone slab single colour (not less than 0.25 Sqm each piece) flooring 18-20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing mirror finished laid over and including screed bed and bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes single, complete all specified and as directed.

M & L for Kota stone slab (single colour) 18-20mm thick mm thick in riser of steps, skirting, dado and pillar, laid over and including backing plaster of 15mm in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing mirror finished complete all specified and as directed.

M & L for 18-20mm thick Granite (of any type) work, (table rubbed and polished) in steps, jambs, pillars, top of slab, skirtings with necessary hole where ever required laid over and including cement mortar bedding of 15mm thick in CM 1:4 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges complete all specified and as directed. Note: colour of granite stone shall be Z black costing not lessthan Rs.150/- per sq ft including GST.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed or bedding layer of mortar 15 mm thick in Cm (1:4) for laying floor finishes complete all specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface 450x300mm, 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick backing plaster in Cm (1:3) on fair faces of brick work to receive tiles complete all specified and as directed.

S & F in repair Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured, with integral foot rests, fixed in repairs including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) , white fixed with and including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device complete all specified and as directed.

S&F in repairs Vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all specified and as directed.

S&F in repairs PVC low level white flushing cistern, valveless syphonic action type 10 ltr capacity with inlet, ball valve, float and handle including PVC flush pipe 32mm dia bend and a pair of mild steel iron brackets of suitable size including making necessary connection to water supply pipe line complete all specified and as directed.

S&F in repair counter sunk Vitrous china wash hand basin white, oval type Wash hand basin min size 560x400mmx205mm, including necessary waste pipe and coupling, Fixing over Granite Counter complete all specified and as directed.

S&F in repairs brass chromium plated shower rose of size 125 mm with arms including fixing to steel pipe complete all specified and as directed.

S&F in repairs corner shelf with Z Black granite piece quadrant shape radius 250-300 mm with min thickness 20mm including cutting, moulding, polishing and fixing arrangement on walls at corner etc complete all as specified and directed.

S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece complete all specified and as directed.

S&F in repairs stop valves concealed type, cast copper alloy, fancy type, chromium plated with long shank & cup with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore complete all specified and as directed.

S&F in repair 15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed complete all specified and as directed.

S&F PVC health faucet alongwith 1.00 to 1.50 meter long good quality PVC flexible connection pipe suitable for 15mm bore pipe complete all specified and as directed.

S&F toilet paper holder with flat recessed type Stainless Steel complete all specified and as directed.

S&F in repairs PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe complete all specified and as directed.

S&F in repairs wash hand basin mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all specified and as directed.

S&F in repairs chromium plated grating with 100mm dia of approved make including fixing with 1:4 C:M to floor/nahani traps etc complete all specified and as directed.

S&F tubular towel rail of brass chromium plated, 20mm dia, D type, 60 Cm long between flanges complete all specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc; overall thickness and removing the dust debris etc to a distance not exc 250 meter from site and disposing the same complete all specified and as directed.

Dismantling of floor of size not exceeding 1.50 Sqm mtr for water closet/bath and removing out the cinder/concrete from sunken portion, , grinding any sharp edges etc complete all specified and as directed. (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques as per site conditions. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick in cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 40 mm dia PVC pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and providing 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 1.50 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

M&L for cement concrete 1:3:6 type C2 (using 20mm graded crushed stone aggregates) in plinth protection, 50 mm thick, finished even and rough, including M&L for machine pressed, factory made, Glossy finished chequered cement concrete tiles 30 cm x 30 cm x (22-25)mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment laid over and including 20 mm thick screed bed or bedding layer of cement mortar (1:4) for top finishes complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all specified and as directed.

Taking down chowkats with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete all specified and as directed.

S&F factory made solid WPC (wood polymer composite) door frame 125mmx65mm double rebated made from WPC (single extruded process) material comprisin of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, having good screw holding capacity (screw withdrawl strength of min 990 N), min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing in position with SS Dsh fasteners/ hold fast of required dia and length complete all specified and as directed.

S&F factory made single extruded WPC (wood polymer composite) solid door frame of size 100mmx65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fiber (wood powder/ rice husk/ wheat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100n (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant complete all specified and as directed.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum of density 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer?In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) complete all specified and as directed.

S&F 35mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminum Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares should be fixed with 19*6mm size steel screws etc. Complete all as directed/ specified and as per manufacturer's specification and drawings.

S&F factory made single extruded WPC (wood polymer composite) soild plain flush door shutter of 30mm thick comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame of density 650 kg/cum, screw withdrawl strength of 2200 N (face) 1100N (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/MM2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk SS screw, complete all specified and as directed.

S&F 150mm long stainless steel barrel tower bolts complete all specified and as directed.

S&F 200mm long stainless steel barrel tower bolts complete all specified and as directed.

S&F 150mm size stainless steel handles complete all specified and as directed.

S&F 250mm long stainless steel sliding door bolt with staple (bolt type) and fixing clips and fixing bolts and sliding bolts complete all specified and as directed.

S&F butt hinges, stainless steel 100mm size complete all specified and as directed.

S&F 140mm floor door stopper of stainless steel body and tongue with hard drawn steel spring fixed in floor complete all specified and as directed.

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) window shall have provision for installation of window AC/Desert Cooler and provision of window glass shutter, wiremesh, grill and necessary fittings and locking arrangements for subject portion will be modified as per ground requirement during the execution as per directions of Engr-in-charge. (viii) Window shall be installed with silicone complete all specified and as directed.

S&F aluminium ventilator with outer frame 40mmx114mm with 1.3mm thickness corner 45 degree cut & aluminium welded center mullion size 40mmx65mm partly glazed/ gauzed including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws , MS wire mess , 3mm thick sheet glass etc. provision for fixing the exhaust fan complete all specified and as directed.

S & F for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate, welding to steel frame complete all specified and as directed.

Demolition of reinforcement cement concrete of any discription and in any position, including cutting of reinforcement from adjoining RCC component to faciliate demolition complete all specified and as directed. Note - All scaffolding & T&P up to three/four storey building required for demolition/dismantling of RCC shall be part of this item .

M&L for providing and fixing Mild Steel railing on stair case made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement complete all specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all specified and as directed.

S&F in repairs stainless steel of grade S-304 for curtain rod of 20mm nominal bore & 1.6mm thick of fancy type including brackets, side knobs etc, fixed to walls complete all specified and as directed.

Taking up or down 15mm bore steel tubing and connections including cleaning for re-fixing or removal to store complete all specified and as directed.

Taking up or down 25 to 32mm bore steel tubing and connections including cleaning for re-fixing or removal to store complete all specified and as directed.

M&L supplying and fixing of 15 mm bore Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/floor/wall/ceiling complete all as specified ( brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor complete all specified and as directed.

All as per item no -55- here in before but 25 mm bore of pipe complete all specified and as directed.

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres complete all specified and as directed.

S&F 1000 ltr capacity 04 layered, white coloured rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all specified and as directed.

Dismantling water tanks of capacity exceeding 1000 litres but not exceeding 2000 litres complete all specified and as directed.

S&F 2000 ltr capacity 04 layered, white coloured rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all specified and as directed.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete all specified and as directed.

S&F in repair 25 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all specified and as directed.

Dismantling up to 100/75mm bore cast iron pipe (soil/ waste/ vent) with fittings, jointed with cement or lead including burning out lead joint, from wall or floors including of all fittings such as tee, bend, branch pieces complete all specified and as directed.

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc or removal to store(measured overall as fixed along the centre line over fittings and accessories complete all specified and as directed.

S & F PVC (SWR) pipes 110mm bore, single socketed in any length with rubber ring joints fixed to walls complete all specified and as directed.

S & F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints fixed to walls complete all specified and as directed.

S & F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints laid in trenches complete all specified and as directed.

S&F for PVC (SWR) bends any radius, 110 mm bore complete all specified and as directed.

S&F for PVC (SWR) bends any radius, 75 mm bore complete all specified and as directed.

S&F for 110 PVC (SWR) Tee with door plate complete all specified and as directed.

S&F for 75 mm PVC (SWR) Tee with door plate complete all specified and as directed.

S&F for 75 mm bore PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in solvent cement concrete complete all specified and as directed.

S & F Stack clamps to hold for 110mm dia PVC rain water with wall made out of 25mm x 2mm flat iron and 10mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete all specified and as directed.

S & F Stack clamps to hold for 75mm dia PVC rain water with wall made out of 25mm x 2mm flat iron and 10mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for any bore and any type of pipes complete all specified and as directed.

S&F in repairs 180mm x 150mm salt glazed stone ware gully traps square & round mouthered trap 'P' including case iron grating and fixed, including necessary excavation and earthwork, concrete in bed, surrounds, kerbs etc., and jointing to drains in CM 1:1 complete all specified and as directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debrish from the MOD land complete all specified and as directed.

M&L for 15 mm thick rendering with readymix plaster (as per manufaturer's instruction) on other than fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed. Make of ready mix plaster : Birla Aerocon/ Ultratech readiplast/ ACC accoplast.” Note :- Contractor shall be bounded to carryout repair / maint upto G+1 storey building and the rate shall be deemed including scaffolding / double scaffolding, safety equipment and misc accessories

M&L for 15 mm thick rendering with readymix plaster (as per manufaturer's instruction) on fair face of brick or concrete surfaces finished even and smooth surface without using extra cement complete all as specified & directed. Make of ready mix plaster : Birla Aerocon/Ultratech readiplast/ACC accuplast.” Note :- Contractor shall be bounded to carryout repair / maint upto G+1 storey building and the rate shall be deemed including scaffolding / double scaffolding, safety equipment and misc accessories

M&L rendering 5mm thick with ready mix plaster on ceiling surfaces finished even and smooth without using extra cement complete all as specified & directed. Make of ready mix plaster : Birla Aerocon/Ultratech readiplast/ACC accuplast.” Note :- Contractor shall be bounded to carryout repair / maint upto G+1 storey building and the rate shall be deemed including scafolding / double scafolding, safety equipments and misc accessories

Supply only liquid water proofing compound as per latest IS code complete all specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plastered surfaces of ceilings and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for complete removal of existing treatment from internal surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from internal surfaces of ceiling by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from from external surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all specified and as directed. Note: (a) All works shall be done mechanically through authorised applicator of manufacturer only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for chipping of spilled and loose concrete and cleaning rust from reinforcement by sand blasting scrubing down concrete surfaces with wire brushes cleaning with water allow to dry and applying a layer of Zinc rich epoxy primer as an anti rust on all exposed reinforcement followed by a layer of binding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperture 75mm. Thickness of guniting ranging grom 20mm to 400mm in cement mortar 1:2 using OPC 53 grade cement mixed with polycreate mixture @ 2% by weight of cement or as per manufacturer's instruction and finally applying cement plaster over guniting surface of required thickness to give even, uniform and smooth finishes confirming to proper geometrics in cement mortar 1:3 to match the existing surfaces as in sides, soffits of the slabs, chajjas, fins, facias, parapets, linetls, columns and beams etc complete including necessary scafolding, shuttering, chasing to brick work or RCC members at any height upto 6 storied buildings including removal of all small trees/ shrubs etc , complete all specified and as directed.

Dismantling brick tiles or terracing tiles single layer on roofs complete all specified and as directed.

Demolition of mud/ mud phuska in roofs any thickness, including plastering and leaping if any and removal of mud /mud phuska to a distance exc 250 M and n exc 500 M complete all specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in proper slab for roof padding including finished even & smooth without using extra cement complete all specified and as directed.

M&L for 15mm thick screed bed (average) plaster on concrete surfaces in CM 1:4 on roof mixed with WPC and finishing the surface even and smooth without using extra cememt complete all specified and as directed. (WPC shall be measured and paid seperately).

M&L for priming roof surfaces and applying water proofing treatment over roof including preparation & cleaning of roof surface comprising of the following complete all as specified & as directed:- (a) Applying oil bound bituminous primer at the rate of 0.4 Ltrs/sqm as per IS 3384-1986 on prepared surfaces. Surfaces shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated. (b) Applying one coat of hot straight run bitumen @ 1.2 Kg/sqm of grade 85/25 confirming to IS-73. (c) Laying 3 mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyester matt, with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75 mm at sides and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminous primer, all as per manufacturer's instruction including preparation of surface. Note: Water proofing treatment shall be got carried out by the manufacturer or their authorised applicators. Contractor shall give 10 years guarantee for effectiveness of water proofing treatment. 2.5% of work done amount of this items shall be retained from the contractor payment for a period of 10 years reckoned from date of physical completion of the work or in lieu contractor may deposit bank FDR for the said tory for 10 years which shall be released by GE on the expiry of satisfactory completion fo 10 years period complete all specified and as directed. (d) Finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against UV, including preparing of surfaces of roof (second coat apply after 24 hrs or as per manufacturing instructions).

M&L for plain cement concrete 1:3:6 type B-1,using 20mm graded stone aggregates as in coping to parapet walls including necessary formwork complete all specified and as directed.

M&L for providing and injecting chemical chlorpyrifos emulsifiable for post constructional anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre (mixing 2.10 ml chemical with one litre of water) including drilling and plugging holes @300mm c/c complete all specified and as directed.

M&L for anti termite treatment of soil under existing floors using chemical chlorpyrifog emulsifiable concentrate @ one litre per hole (mixing 2.10 ml chemical with one litre of water), 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floors, complete all specified and as directed.

M & L for 18-20mm thick machine cut marble (any colour) as in floor high lighter (used as strips of any size) laid over and including cement screed base 20mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all specified and as directed. Note:- Colour/shade of tile to be approved by GE.

M&L for providing reinforcement cement concrete M-25 (Nominal Mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all specified and as directed.

S&F milt steel TMT bars 10 mm dia and over , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia complete all specified and as directed.

S&F in repairs heavy duty stainless steel peg set of minimum size 450mm x 50mm with 6 pegs fixed on to walls/ doors with screws and necessary fittings complete all specified and as directed.

M&L for from work to soffits of suspended slabs such as roof slabs, floor slabs, landing & similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces complete all specified and as directed.

M&L for cement plaster 15mm thick in CM 1:6 on brick or concrete surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete all as specified and directed. NOTE : Rates for water proofing compound/ polymer deemed to be included in the quoted rates

M &L for providing and applying a bond coat of Latex: Water: cement (1:4:6) consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete all as specified and directed Make : SIKA/BASF/FOSROC

M&L for Exposing the first joint of masonry structure at ground level horizontally and knocking off the plaster atleast 50 cm beyond the visibly penetrated area., scrapping out damaged mortar joints to a depth of approximately 2-3 cm. Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of Engineer in Charge. Cleaning of holes by air blower prior to fixing nozzles, installation of latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten, Fixing the packer securely using sealent and Cutting/removing of Packers after completion of grouting/injecting without damaging structural elements complete all as specified and directed.

Supplying and application of very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time, having mixed viscosity 3 to 11 m.Pa.s at 20 Deg C, reaction time adjustable according to ambient temperature and execution time requirement between 8-50 mins, the polyacrylic resin is pumped into the wall through packers injection at a pressure > 20 Bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas cause rising dampness. When polyacrylic resin movement stops or polymer compound appears at the packer, move to the next packers and inject (Approx 0.2-0.3 Kg resin per packer). Make : SIKA/FOSROC/BASF

Description of Work / Item(s)

Amount

Taking down carefully the old U/S Aluminium / Copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated single core unsheathed FRLS 1100 volts grade electrical cable drawn through existing concealed PVC conduit in wall and ceiling including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes of min thickness 1.2mm with 120 GSM coating including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable single core PVC insulated unsheathed earth continuity wire to common earth and connected to earth dolly complete all as specified and and directed. Notes : (i) The rates shall be inclusive of providing point wiring on casing caping, if there is blockage/damage in existing conduit on ceiling. (ii) The quoted rates shall be inclusive of cutting/chasing and making good disturbed surfaces with CM 1:3 and same finishes with adjoining surfaces of disturbed area with OBD/Colour wash/white wash etc as per site requirement.

All as per item No 2 above but One 3 pin socket outlet, 5/6 Amps, independent, with cables 1.5 sq. mm size with through existing concealed PVC/MS conduit.

All as per item No 2 above but 5 Amp socket outlet on same board.

All as Item No 2 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing with through existing concealed PVC/MS conduit.

One light point controlled by two 2-way switches, with cables 1.5 sq. mm

S & F switch Modular type, 1 module 5/6 Amps SP one way all as specified and directed.

S & F socket outlet 2-in-1, 5/6 Amps modular type 5 pin multi purpose all as specified.

S & F switch modular type 1M 15/16 Amps SP one way all as specified. Notes:- one power point wiring shall be provided on one circuit of one point only.

S & F universal socket outlet 2-in-1 (multipurpose) 5pin 6/16 Amps modular type all as specified.

S & F ceiling rose surface Bakelite 65x25 mm two to three terminals

S & F switch modular type 1 M 5/6 Amps SP 2 way all as specified.

S&F Bell push modular type 1M 5/6 Amp complete all as specified and as directed.

S&F electric bell ding dong type AC, 230 volts single phase, complete all as specified and as directed.

S&F surface mounting LED Integrated Aluminium Batten luminarie Polycarbonate co-extusion tube for 20W LED light housing. Fixture should have minimum system lumen of 2000lm & minimum efficacy at system level >=120 lumens/Watt, life of fixture 25K Hrs, CCT 4000-6500K with same lumens/w CRI>80, PF>0.90 THD<20% @ 240v Ac. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed. Make-Bajaj Cat Pt No – BCLAB 20W CWLED XT (115072), Philips Cat Pt No BN308C LED205-6500L120PSUWH, Eveready Cat Part No LED5BTA02016-02HE, Havells Cat Part No-LUMILINE+ BS20WLED830SPCSS

S&F in replacement of LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE including all accessories connecting up twin core flexible copper conductor cable complete all as directed.

S & F 10 Watt wall mounted mirror LED batten having PC diffuser luminous efficiency not less then 120 lumen/Watt CRI>80%, PF>0.9,CCT 6500K independent isolated SPMS based constant current electronic LED driver with THD < 10% surge protection and other safety tests as per IS 15885( Part-2/Sec-13) : 2012 polycarbonate diffuser housed in powder coated white extruded aluminum channel housing , white colored ABS end caps IP 20protection input voltage range 140-270V input frequency 50-60Hz including electrical connection with 3 core flexible Cooper Conductor cable of Appropriate size from ceiling rose to the fixture complete all as specified and as directed. Make- Eveready Cat Part No LED BTA010I6-01 HE,Halonix Cat Part No HLB-03-10-CW-AL-SQ-HL2, Havells Cat Part No- LUMILINE+BS10WLED865SPCSS

S&F in repairs surface mounted round shaped LED downlight durable housing with aluminium heat shrink diffuser to give glare free light 12 watt LED 6000K lamp type from ceiling of stairs/common areas complete all as specified and as directed.

S&F in repairs wall mounting 12 Watt LED decorative wall light fixture made up of Polycarbonate, with suitable connections complete all as specified and as directed.

S & F LED re-chargable Lamp of 12 Watt for fixing in batten holder/wall mounting/bulkhead point all as specifed and directed by Engr-in-Charge

S&F in replacement of LED Building security light fitting 35Watt including fabrication of GI bracket 25mm dia medium grade suitable for fixing of LED light fitting duly fixed with clamps, nut, bolts, & washers etc. and all as specified and directed.

S&F of steel body exhaust fan 300mm sweep, 230 Volts with louver and copper wound including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with complete including taking down old Exhust fan and depositing to MES store yard complete all as specified and directed all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, remote with batteries and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) all as specified and directed. Make- Havells cat part No FHCPE5SPWT48 model Enticer or equivalent in Bajaj and Crompton

S&F Modular Type Electric Fan regulator 120W step type complete all as specified and directed. Make – Compatible to make of ceiling Fan as approved by GE.

Taking down of VTPN DB 4 way including electrical connection complete all as specified and directed by engr in charge all as specifide and directed.

S&F in replacement of VTPN DB triple pole and neutral 4 way for fixing 4P MCCB up to 125 Amps as incomer and MCBs as out goings with rubber gasket and metal double door and IP 43 Protections and connecting complete including making good to disturb surfaces with CM 1:3, same surface finished with the adjoining surface of disturbed area and the rates are inclusive of quoted rates complete all as specified and directed.

Supply & Fixing MCCB 125 Amps, 4 pole, 415 Volts, 36kA in replacement old unsv isolator any type complete all as specified and directed.

S&F in replacement MCB DB SPN 16 Way with rubber gasket, double door type, (IP 43 Protection) flush mounting for MCBs all as per site requirement and as directed.

S&F in replacement MCB DB SPN 12 Way with rubber gasket, double door type, (IP 43 Protection) flush mounting for MCBs all as per site requirement and as directed.

S&F in replacement MCB DB SPN 04 Way with rubber gasket double door type, (IP 43 Protection) flush mounting for MCBs all as per site requirement and as directed.

S&F in replacement MCB SPN 40 Amps 'B' series, breaking capacity 10 Ka, 'B' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc complete all as specified and directed.

S&F in replacement for MCB SP 10 to 32 Amps 240 Volts, 10 KA, `B' curve, all as per site requirement and as directed.

M&L for safely taking down of roof top solar water heating sytem(Evacuted tube collector) with 1000LPD hot water tank with electrical backup 3Kw disconnection including all fitting and angle iron support complete all necessary plateform and keeping the same in safe custody till completion of B/R roof tretment work complete all as specified and directed.

Installing, testing and commissioning Solar water heating sysyem (Evaculated Tube collecter ) retrieved from item No 33 here in before with consultation of the rep company of the manufacturer to raise watyer temprature upto 60-70 degree celcius on clear sunny day with 1000LPD hot water tank as per IS-12933 and IS 12976 including electrical backupo of 3 KW including all fitting and angle iron support (60x60x6mm) with necessary fabrication welding and work complete with nuts bolts and washers and painting with two coats of synthetic enamel paint over a one coat of red oxide primer for mounting of hot watr tank complete all as specified and directed. Note – Any damage occur to solar water heating system will be made good by the contractor at his own cost without any extra payment

Taking down unserviceable sub main wiring twin core of any size complete and making good disturbed surface complete all as specified and directed.

M&L for submain wiring in replacement PVC insulated FRLS single core with stranded copper cable of size 6 Sqmm in 2 runs and 6 Sqmm one run for earth drawing through existing PVC concealed conduit 25 mm dia conduit complete all as specified and directed. Note:-(a) Two runs of main cable and one run of earth cable all-together shall be considered as one length. (b) New conduit of suitable size with connected fitting will be laid if there is a damage/blockage in existing conduit including making good to disturb surfaces with CM 1:3, same surface finished with the adjoining surface of disturbed area and the rates are inclusive of quoted rates.

M&L for submain wiring in replacement PVC insulated FRLS single core with stranded copper cable of size 4Sqmm in 2 runs and 4 Sqmm one run for earth drawing through existing PVC concealed conduit 25 mm dia conduit complete all as specified and directed. Note:-(a) Two runs of main cable and one run of earth cable all-together shall be considered as one length. (b) New conduit of suitable size with connected fitting will be laid if there is a damage/blockage in existing conduit including making good to disturb surfaces with CM 1:3, same surface finished with the adjoining surface of disturbed area and the rates are inclusive of quoted rates.

M&L for Earthing complete with galvanized steel earth plate 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate n.less than 1.5 m below normal ground level, connected to galvanized iron wire 4 mm as earthing lead by means of bolts, nuts, check nuts & washers of galvanized iron or steel besides building at all joints as shown in drgs and including excavation and earth work, GI pipe light grade 25mm bore of protection of GI wire from earth electrode, supply and laying charcoal dust, common salt, PCC (1:2:4) type B-1 Chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type B-1using 20 mm graded stone aggregate Reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia , PGI funnel and wire mesh , 20 mm dia GI Pipe light grade for watering complete all as shown in drg and connected to earth test point including testing as directed by Engr-in-Charge.

Taking up UNSV XLPE cable any size complete all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded ,galvanised steel strip armoured ,electric power cable (heavy duty ) 1100 volt grade with stranded aluminium conductor of size 50 sqmm, 3.5 core complete all as specified and directed.

Excavation in trenched not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exe 25 cm complete all as specified and directed.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Supplying and laying Double wall Corrugated (DWC) pipe in excavation of trenched of 40mm size including all connecting necessary items complete all as specified and directed.

Boring holes under road pavement by bocky manually in any type of soil upto 50 mm bore complete all as specified and directed.

M/S Chhavi Constructions Co (BID ID -3393951)

L G BUILDERS (BID ID -3393861)

A R construction (BID ID -3393937)

Shivom Projects Private limited (BID ID -3394259)

Chaudhary Constructions (BID ID -3393412)

India Guniting Corporation (BID ID -3394104)

P R Constructions (BID ID -3394092)

M/S ADHIKARI CONSTRUCTION CO. (BID ID -3390464)

Parveen Builders (BID ID -3392992)

Parveen Builders (BID ID -3392992)

Shivom Projects Private limited (BID ID -3394259)

A R construction (BID ID -3393937)

L G BUILDERS (BID ID -3393861)

M/S ADHIKARI CONSTRUCTION CO. (BID ID -3390464)

SAGGI ELECTRIC COMPANY (BID ID -3390281)

Chaudhary Constructions (BID ID -3393412)

India Guniting Corporation (BID ID -3394104)

P R Constructions (BID ID -3394092)