Interior and Fit-out works of Income Tax Department (ITD) Office, Tower-E, 8th Floor, at World Trade Centre, Nauroji Nagar, New Delhi-110029

GENERAL ABSTRACT OF COST

Name of Work : INTERIOR/ FURNISHING WORK OF INCOME TAX DEPARTMENT (ITD), TOWER-E, 8th FLOOR, WTC, NAUROJI NAGAR, NEW DELHI.

Sub Head No. Description DSR NDSR/MR Total

CHAPTER-1 CARRIAGE OF MATERIALS 63,989.00 0.00 63,989.00

CHAPTER-3 CLADDING WORK 47,717.00 2,750,443.51 2,798,160.51

CHAPTER-4 DOOR & WINDOW WORK 3,934,287.00 621,030.75 4,555,317.75

CHAPTER-7 WALL FINSHES WORK 15,715,353.00 22,776,400.20 38,491,753.20

CHAPTER-8 REPAIRS TO BUILDING 100,643.00 0.00 100,643.00

CHAPTER-9 METAL WORK 40,152.00 0.00 40,152.00

CHAPTER-10 WATER PROOFING 43,687.00 0.00 43,687.00

CHAPTER-11 FURNITURE WORK 0.00 54,109,272.18 54,109,272.18

CHAPTER-12 PLUMBING WORK 96,963.00 441,007.00 537,970.00

CHAPTER-15 UPS System Work 6,160,000.00 6,160,000.00

CHAPTER-17 Data Centre Works Inc. Active And Passive 11,745,475.00 11,745,475.00

CHAPTER-18 Computers & Printers 12,563,200.00 12,563,200.00

CHAPTER-20 FIRE ALARM SYSTEM 2,086,794.30 1,060,584.00 3,147,378.30

CHAPTER-24 Horticulture 0.00 3,908,500.00 3,908,500.00

CHAPTER-25 Access Control 23,126.78 5,210,885.90 5,234,012.68

Multiplication factor for Modified Analysis of Rates @0.973 on DSR Items 41,355,356.96 201,535,841.94

Estimated Cost put in the Tender including GST , Say (Rs) 242,891,199.00

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD, NEW DELHI

ABSTRACT OF COST

NAME OF WORK -INTERIOR AND FINISHING WORK

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1 CARRIAGE OF MATERIALS

1 1.1.18 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by cum 129.51 494.10 63989

mechanical transport including loading, transporting, unloading to approved municipal dumping ground for

all lifts, complete as per directions of Engineer-in-charge.

Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of

load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Carriage Of Materials : 63989

SH 2 CIVIL WORK

1 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and cum 140.00 7878.5 1102990

shuttering 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources)

2 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, cum 2.59 11505.5 29822

balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth

level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm

nominal size derived from natural sources). for all rcc work

3 5.9 Centering and shuttering including strutting, propping etc. and removal of form for sqm 17.28 736.4 12725

4 5.22.3 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding kg 219.66 107.85 23690

all complete above plinth level. Thermo-Mechanically Cold twisted bars

5 6.38 Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super cum 21.20 10195.45 216111

structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate

includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Sqm 28.80 1123.8 32365

superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

7 13.4.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) Sqm 57.60 357.75 20606

13.4.2 15 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) Sqm 28.80 343.65 9897

8 MR -1 Providing Pest control and Anti-termite treatment by appointing a specialised agency as per the Sqm 1500.00 225 337500

specifications mentioned by the Bureau of Indian Standards and Agencies specifications (whichever is

higher), for General Civil, Plumbing,/ Drainage and timber. The termite treatment has to be done in two

stages as pre-renovation and during renovation. Vendor should provide 2 yrs warranty on completion of

9 MR -2 Preparation of complete set of shop drawings including finishing, MEP services, details, design calcualtions LS 1 2400000 2400000

etc. and any other details as and when desired by Engineer In charge /client. A qualified professsional for

the purpose shall be appointed after due appproval from Engineer In Charge.

Total Carried Over to Abstract for Sub Head: 2.00 Civil Work : 1448206 2737500

SH 3 CLADDING WORK

1 MR -3 Providing and fixing 12 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Sqm 15.66 5116.46 80123.76

for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved

shade, colour and texture laid over 18 mm thick thick HDMR ply board, joints treated with white cement,

mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges

to give high gloss finish etc. complete at all levels.. Granite stone slab including machine polishing to edge

to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work Base

2 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., metre 52.20 510.95 26672.00

3 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width metre 31.32 568.95 17820.00

upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

4 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity each 2.40 978.70 2349.00

counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete.

5 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish Sqm 1.73 506.70 876.00

complete.Base rate 300Sqft

6 MR -5 Providing and fixing Ist quality vitrified wall tiles conforming to (thickness to be specified by the Sqm 300.00 3378.43 1013529.00

manufacturer), of approved make, in all colours, shades of any size as approved by Engineerin- Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand)

and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in epoxy grout of matching shade

complete. size of tiles 1200mm x 2400 mm BASE 170

7 MR -7 Providing and fixing machine cut, mirrorl polished , ONYX stone work for wall lining (veneer work) including Sqm 32.00 28097.00 899104.00

dado, skirting, risers of steps etc., in required design and pattern. If required with marble stone slab pieces

of different shapes, shades and texture but of even thickness., on 12 mm (average) thick cement mortar 1:3

(1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/ sqm including pointing with

white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all

complete as per Architectural drawings, and as directed by the Engineer-in-Charge. Stone slab of any colour

basic price 1500 rs Sqft

CLA Digitally signed by AMITNBCC

8 MR-8 Providing and fixing machine cut, mirror/ eggshell polished ,Italian Marblestone work for wall lining (veneer Sqm 75.00 10102.49 757686.75

work) including dado, skirting, risers of steps etc., in required design and pattern. If required with marble

stone slab pieces of different shapes, shades and texture but of even thickness., on 12 mm (average) thick

cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/ sqm

including pointing with white cement slurry admixed with pigment of matching shade, including rubbing,

curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab of any colour basic price 450 rs Sqft

Total Carried Over to Abstract for Sub Head: 3.00 Cladding Work : 47717.00 2750443.51

SH 4 DOOR & WINDOW WORK

1 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed cum 22.92 142949.7 3276407

and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or

dash fastener shall be paid for separately). Second class teak wood

2 9.112 Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with metre 183.36 205 37589

wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as

per direction of Engineer-in-charge.

3 9.20.1 Providing and fixing marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of Sqm 178.56 3473.85 620291

block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked

Stainless Steel butt hinges with necessary screws

4 MR-13 Providing and Fixing 240 mm lock body for wooden doors of approved make and model all complete as each 28.00 1917.14 53679.92

per the direction of Engineer-in-charge.

5 MR-14 Providing Double cylender Floor Spring D-120 for Wooden door with Closing Force EN 4 with Maximum Set 21.00 12849.67 269843.07

door weight 120 Kg. Maximum door width 1250 mm.Closing speed : 130° Final closing speed : 15-0°. Hold

Open (standard): 90° hold open. Weight of floor spring approx : 6kg, 5,00,000 cycles Tested. approved make

and model all complete as per the direction of Engineer-in-charge.

6 MR-15 Providing top and Bottom Strap/Door Pivot for wooden doors of approved make and model all complete as set 23.00 705.03 16215.69

per the direction of Engineer-in-charge.

7 MR-16 Providing and Fixing 60 mm Ultero Cylinder 1CK Antique Brass Cylinder One side knob and one side regular each 25.00 1602.87 40071.75

key for wooden doors of approved make and model all complete as per the direction of Engineer-in-charge.

8 MR-17 Providing and Fixing Rose Handle Antique Brass for Store, of approved make and model all complete as per each 27.00 3949.10 106625.70

the direction of Engineer-in-charge.

9 MR-24 Providing and Fixing Concealed Door closer T660 -60 kg (CE certified) for wooden doors of approved make each 11.00 7340.68 80747.48

and model all complete as per the direction of Engineer-in-charge.

10 MR-25 Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of each 38.00 487.83 18537.54

approved make and model all complete as per the direction of Engineer-in-charge.

11 MR-26 Providing and Fixing 300x15x15 mm ss 304 Tower bolt -Square Type with screw for Wooden Doors of each 20.00 1765.48 35309.60

approved make and model all complete as per the direction of Engineer-in-charge.

SH 5 FLOORING WORKS

VITRIFIED FLOOR TILES

1 Providing and laying vitrified tile flooring with 3mm Spacers CM 1:4 (1 Part Cement: 4 Part M Sand) of

20mm average. vitrified tiles of approved shade & laying pattern as per drawing in flooring with 3mm spacer

joints, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) / Tile adhesive by weber / approved

equivalent make, including grouting the joints with graphite grey epoxy resin based grout PPDG-05 of AGL /

Myk make or equivalent and matching pigments, etc. with water absorption less than 0.08%and conforming

to IS:15622, of approved, make, in all colors and shades cleaned & washed with a suitable effective Cleaning

agent or any suitable means as per instructions of EIC, covering to protect tile with 275 GSM – 2 mm thick

Floor guard make or equivalent, joints to be taped, should remain intact till handing over, removed &

disposed of out of the site after completion, etc., complete. The rates quoted shall include the Rate required

to lay the tiles at the proper level if required, the Rate & cutting of tiles for laying borders/ patterns, etc,

complete in all respects as per details. Double charge vitrified tile polished finish of size

a MR-27 Size of Tile 600 x 600 mm base rate 65 sqm 450.00 1736.58 781461.00

b MR-28 Size of tile 600 x 1200mm base rate 95 sqm 500.00 2103.42 1051710.00

c MR-29 Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm base rate 70 sqm 69.24 1815.70 125719.07

2 11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic sqm 1349.06 174.5 235410

coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm

3 MR-31 Providing and fixing Engineered wooden flooring 15 mm up to 3 mm top layer, core layer pine wood oak sqm 720.00 5419.64 3902140.80

finish or equivalent with necessary T- profile and reducer fixing with underlayer 2 mm thick High Density

polyurethane foam having density of approx. 90 kg/cum and 2 mm thick rubber sheet as per manufacureres

specifications and as directed by engineer in charge. base price 350sqft

4 MR-33 Providing and laying machine cut, mirror polished Italian marble flooring Marble stone flooring, in required sqm 1280.00 8047.77 10301145.60

design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of

different colours, shades and finished surface texture etc., in linear portions of the building, all complete as

per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including

pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing,

curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick

Italian Marble basic price 450 sqft

CLA Digitally signed by AMITNBCC

5 MR-35 Providing and laying of 2mm conductive Vinyl rolls as specified and indicated. The cost to include preparing sqm 88.32 2477.55 218817.22

surface to receive vinyl flooring requirements like the floor to be absolutely leveled, hard, dried, even and

free from dirt, grease, moisture , and fixed using required adhesive ( water based adhesives like Arobond 44

of Colourbond mktg/VC 31 of Pidilite Ind. ) and correct laying technique. The make of vinyl flooring shall be

of Armstrong or equivalent of which the specs / samples have to be submitted for approval. basic price 700

Flammability : B1 Class

Sound Absorption : 3 dB

Sheet width/length : 180/16-25 cm/m

Tile side length : 60.8/60.8 cm/cm

Total wt : 2.9 kg/m2

Colour fastness : 6 stage

Electrostatic loading limit : <2 Kv

Thermal resistance : 0.010 m2K/W

6 MR-36 Providing and laying Carpet plank/ tiles of Yarn type 100% Nylon; Multi-Level Pattern Loop, manufactured sqm 220.00 4258.29 936823.80

using 100% solution dyeing process, Tiles of size 50cm x 50cm / 25cm x 100cm equivalent as per direction of

EIC and site requirement with SSP® Soil Protection treatment ™ or equivalent containing properties of Stain

Repel, with - pro care backing, pro care self guard, procare fiber with recycled content, made from

thermoplastic with commercial very heavy , Class B1, TVOC Release amoutn A level < 0.500mg/m2h

Radiant Panel class 1rated ( ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less

Than 3.5 kv, Texture Appearance Retention Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes

(AATCC-174). CRI Green Label Plus is certified for indoor air quality, including fixing/ installation with Low/

Zero VOC content Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) Basic Rate

7 MR-38 Supply of 100 mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thichness Rm 1317.30 1392.47 1834300.73

1.30 to 1.50 mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and

8 11.54.2 Providing and fixing removable raised/false access flooring with system and its components of approved sqm 12.96 5977.35 77466

make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load

bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as

per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI

fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment

upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be

fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the

machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm

thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded

screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer

assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor

panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor

for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as

directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel

Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and

20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and

cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious

core mixed with lightweight foaming compound.

The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology

upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a

Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel

which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL)

minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers

specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of

the panel to ensure the quality of the product 450 mm Finished Floor Height (FFH).

CLA Digitally signed by AMITNBCC

Total Carried Over to Abstract for Sub Head: 5.00 Flooring Works : 312876 19152118.22

SH 6 CEILING WORKS

PLAIN GYPSUM BOARD CEILING

1 12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sqm 1350.00 1355.8 1830330

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia

x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5

mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long

dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing

to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing

tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification and also including the cost of

making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the

cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

2 MR-39 Providing and fixing suspended ceiling in recessed grid system - 600 x 600 x12.5mm with Unity 4mm holes, sqm 527.28 2095.33 1104825.602

c/c 10 mm with upto 0.8 NRC. Material: Perforated plasterboard ,Board type: Ceiling tileOF SIZE Length x

width x thickness: 600X600X12.5mm ,Edge: E+, recessed grid system ( 8mm recess),Perforation: Unity 4mm

Surface: Water-based acrylic paint,Colour: White NCS 0701 Y24R, RAL 9003; gloss 5, Attachment: 15 or

Silhoutte T-grid system Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Distance between hangers ≤ 1200mm

• Distance from wall to first hanger in direction of load - bearing section ≤ 400mm

• Distance between load bearing sections ≤ 1200 mm.

• Distance from wall to first load - bearing section ≤ 600 mm

• Sub-division executed with cross - sections length 1200 and 600 mm

• Screw spacing for attachment of edge sections length 1200 and 600 mm

• Light sockets of upto 3.0 kg can be integrated directly into the ceiling tiles. In the case of heavier fittings,

load must be taken up directly by the concrete deck or via the grid systemand extra hangers.

Fire rating: A2-s1,d0k

3 MR-40 Providing and fixing suspended false ceiling- : Size 1188X1998X12.5mm Globe perforation 6-8/18 with 8.7- sqm 1000.00 3856.78 3856780

10.5% perforation with NRC upto 0.7 : Regular round perforation of glass fibre reinforced gypsum material,

which includes providing and fixing GI perimeter channels of size 0.55 mm. Thk. having one flange of 20 mm

and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, screw fixed to brick wall/

partition with help of nylon sleeves and screws, at 610 mm centers. The suspended GI intermediate

channels of size 45 mm,0.9mm thk with two flanges of 15 mm each from the soffit at 900 mm centers with

ceiling angle of width 25mm x 10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion

fasteners. Ceiling section of 0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of

10.5mm are fixed to the intermediate channels with help of connecting clips and in direction perpendicular

to the intermediate channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling

section with 25 mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done

mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to

be joined and finished so as to have a flush look with uniflot. Air purification & Air quality.Active reduction

of air polluants thanks to Cleaneo Technology effectively reduces concentrations of VOC’s like alcohol,

aldehydes, ketons and esters as well as unpleasant odours from e.g. food or cigarette smoke Air purification

properties tested according to CEN standards and VDI guidelines by Fraunhof Insistute for Building Physics

The false ceiling surfaces shall be prepared to the satisfaction of the Architect, and shall be applied with

two coats of primer to the satisfaction of Engineering in charge

4 MR-41 Providing and fixing suspended acoustic ceiling in visible, but flush grid system ( with technical panel ) 300 x sqm 130.00 4245.34 551894

1200 x12.5mm flush grid system with high grade, glass fibre reinforced, acoustic, white painted, gypsum tile

with acoustic perforation as Unity Round 4mm c/c 10mm with NRC upto 0.8 . Material: Perforated

plasterboard Board type: Ceiling tile Length x width x thickness: 300X1200X12.5mm Edge: E, recessed grid

system ( 8mm recess)

Perforation: Unity 4mm round

Perforation percent: 11.0%

Surface: Water-based acrylic paint

Colour: White NCS 0701 Y24R, RAL 9003; gloss 5

Attachment: 15mm T-grid system

Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Light sockets of upto 1.0 kg per sqmtr can be integrated directly into the ceiling tiles.

CLA Digitally signed by AMITNBCC

5 MR- 43 Providing and fixing of Geo 100mm open cell ceiling with cell size of 100x100mm made out Aluminium . The sqm 37.31 2400.13 89544

assembled cell ceiling panels shall be in size of 600x1200 made out of blades in 9mm (W) x 40mm (H). The

assembled cell ceiling panels are then clipped into U-94 carriers in Aluminium, pre-coated in black

enamelled finished at 1200mm c.c. Wire clips shall hold the cell ceiling panels into the U-94 carriers. Once

the U-94 carriers are installed then primary angles made out of GMS, type U1040 are cross connected to the

U-94 carriers at 1200mm c.c. for lateral bracing The whole ceiling shall be suspended by M6 threaded rods

installed 1200mm c.c.All panel modules must be hingeable through wire clips.

6 MR_ 44 Providing and fixing ceiling system formed as an open metal ceiling with an open area of more than 50%. sqm 62.76 5342.22 335278

The multidirectional ceiling composed of equilateral triangles 600mm modules with perfectly homogeneous

aspect and the im-pression of a uniform assembly. The main blades comprising 100mm height & 25 mm

width interlocked polylams in Extruded aluminium 1.50mm thickness compensating tolerances in x and y

direction. The substructure consists of a form punched perforated profile [U1040] as a lateral grid which is

suspended from the ceil-ing with nonius adjustable upper and lower parts or with threaded rods using

official approved dowel plugs. The grid profiles are to be connected together at the ends by means of

longitudinal connect-ors [U 1041] [screw fasteners]. The spacing of the grid profile is according to the

requirements of DIN EN 13964. On profiles angles, C-band raster as secondary profiles are bolted on by

means of C channel hanger bracket with M6 bolts. Only construction parts ap-proved by the manufacturer

may be used. Provide necessary supports, provisions as per the architects / PM’s Instructions. Toler-ances

according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2008 approved by TUV. Finish of ceiling

is in wood Finish powder coated with mini-mum 60 microns paint thickness.

7 MR- 45 Providing And Fixing Modular Baffle Ceiling system: is vertical & horizontal baffle system, exhibiting space- sqm 160.00 9213.40 1474144

delineating characteristics. The system comprises baffles 40mm wide & 150 Deep thickness of minimum

0.5mm GMS, installed at 150mm C/C . Baffle to be perforated having acoustic fleece pasted from inside. The

C shaped shaped carrier rails run perpendicular to the main baffles profiles. Individual baffle lengths

between 300 and 2400 mm can be selected. Baffle are supplied with the end cap matching the similar finish

of baffle. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by

SIS. Substructure for Vertical baffle system consisting of C shape carrier of minimum 1.2mm thick installed

perpendicularly to baffles, same was hanged to wall with the help of wall anchor fasteners. Baffles to be

connected perpendicular to C shaped carriers with the help of baffle hanger brackets. The primary profiles

must be connected to one another with longitudinal splice connectors. C shaped baffle carriers to be

installed at maximum distance of 1200mm. in a length of 2400 mm baffles. Baffle width:

40mm Baffle height: 150 mm Individual baffle lengths: Min.300/Max.2400mm Material: Minimum 0.5 mm

Surface: Selected Digitally printed Woodgrain finish having minimum 80 micron paint thickness.

Manufacturer shall have the fully automatic powder coating system with power and free conveyorize

3mtr/minute capacity. Powder coating plant shall be equipped with latest modern technology with fully

automatic inline Pre-treatment using nano technology, Inline automatic water Drying system after pre-

treatment. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights,

diffuses, columns etc

CLA Digitally signed by AMITNBCC

8 MR-46 Providing and fixing Veneer finished ceiling feature made of 19mm commercial board and all exposed sqm 190.00 5806.76 1103284

surfaces finished in 4mm thick veneer of approved shade including framing, all fixing hardware, accessories,

making cove, cutout for light fixtures and any other incidentals which may require to secure to false ceiling

and to accomplish the work in all respect as per detail drawings and as directed & approved by architect.

Rate quoted to include vertical drops, making cove and all cut-outs required for light fixtures and other

services cut-outs and necessary supports with hitech rods from the true ceiling complete as directed by

Architect. BR of Veneer 180/-

9 MR-47 Providing and Fixing Custom made Stretch false ceiling to fit exact dimensions with aluminium supports. sqm 50.00 23227.05 1161353

The PVCc ceiling must be stretched and hooked into aluminium rails. Stretch aluminum rails ensuring good

rigidity, to be fixed to the walls or other supports at the specified level. A properitory semi rigid PVC Anchor

( for Tension mounting ) is welded on the outer periphery of the PVC ceiling.

Following are the Technical Specification :

Ceiling Material : Stretchableceiling with PVC Harpoon welded

Thickness : 0.17mm +- 10%

Dimensional Stability : -5 deg to +45 deg C ( No visisble deformation)

Weight : (200 +_ 15 ) g / sqm

Water Vapor permeability :

For Hydrometric degree > 65% RH = 0.0045 g / hr sqm mm Hg

Very effective impermeable barrier to water

Water proof / Dust Proof / Airtight

Resistant to water , dampness, sea water, copper salt solutions and x-rays

Thermal Cofficient : 0.16 kcal/m H C

Fire Classification : B-s2-d0 acc. With DIN EN 14716

Low Emission : CLASS A+ Certified

Total Carried Over to Abstract for Sub Head: 6.00 Ceiling Works : 1830330 9677102.602

SH 7 WALL FINSHES WORK

1 9.105.2 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including Sqm 620.00 1818.15 1127253.00

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal

flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with

nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with

joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal

to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of

primer suitable for board as per manufacture's specification and direction of engineer in charge all

complete. 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum

plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks) on one side and

12mm commercial ply on another side.of partition

2 MR -48 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including Sqm 3320.00 1283.33 4260655.60

providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal

flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with

nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm

thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall

with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with

joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal

to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of

primer suitable for board as per manufacture's specification and direction of engineer in charge all

complete. 75mm overall thickness partition with 12mm commercial ply on both side side.of partition

3 MR - 49 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved Sqm 1200.00 1080.61 1296732.00

primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-

incharge (Frame work shall be paid for separately). 8mm thick commercial ply conforming to IS : 1328 BWR

4 MR - 50 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved Sqm 756.28 1021.74 772720.51

primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-

Charge 6 mm thick commercial ply conforming to IS : 1328 BWR type

5 MR - 51 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved Sqm 1450.00 962.87 1396161.50

primer on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-

Charge 6 mm thick mdf

CLA Digitally signed by AMITNBCC

6 MR - 52 Providing & Fixing of Sleek Partition System SG 75 ie. Single glazed modular system consist of Aluminium sqm 380.00 5806.76 2206568.80

section of 20*75*2 mm thick. All sections duly anodised up to 15-20 microns with 6003 grade and required

accessories ie glass to glass aluminium I sections, T section & 90 degree sections & Glass packing to adjust

the floor level. Ceiling profile & Floor profile and wall profile are 20 mm visible face and 75 mm wide. Profiles

will come in three sides alongwith ( Top, Bottom and Verticle on Wall side) Forth Verticle will come where

No adjusant door comes. Partition will have 10mm toughen glass & insertion of silicon/Thermoplastic gasket

to adhere the glass firm & airtight.

7 MR - 53 Providing & Fixing of Partition Glass Door having SG75 Door Frame with 6003 grade duly Anodized nos 25.00 60442.14 1511053.50

Aluminium Sections having sizes of 75x35x2mm thick, Glass door with 10 mm Toughened Glass including

Hafele/Dorma XLC Door Closure, Hinges, SS Handle (H Type 300mm), SS Bottom Lock,

Silicone/Thermoplastic Gaskets & Screw Caps

8 MR - 54 Providing and fixing flutted glass in partitions etc. with EPDM rubber / neoprene gasket etc. complete as per sqm 53.70 5419.64 291021.66

the architectural drawings and the directions of engineer-in-charge . Toughened glass 10 mm thickness

9 8.28.1 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for Sqm 1600.00 1946.25 3114000.00

plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative

veneer facings of approved manufacture

10 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede Sqm 2168.00 897.30 1945346.00

finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality.

11 MR - 55 providing and installation of ACOUSTIC WALL PANELS. The MDF wall panels shall be composed of Medium Sqm 77.10 6044.21 466009.00

Density Fiber board (MDF) with a minimum density exceeding 710 kgs/m³, and they shall be covered with

PP foil of Renolit, Germany brand/make with a thickness of 120 microns. The adhesive used for affixing the

panels must be PUR (polyurethane) hotmelt glue, and the design of the panels will be as per the

specifications provided by the architect. The dimensions of the panels are 17-18mm in thickness, 130.5mm

in width, and 2745mm in length.The scope of work includes providing and fixing these MDF wall panels onto

a framework constructed either from MDF or plywood. The framework should have a thickness of 50 mm

and a width ranging from 8mm to 12mm. The installation of the panels can be executed through either the

nail-down method or the pasting method, with the use of a high bonding adhesive suitable for MDF and

plywood, NRC 0.65 upto 1 NRC . The finishing of the MDF wall panels should adhere to the approved

architectural drawings and the directions provided by the Engineer-in-Charge (EIC).

12 MR -56 Providing & Fixing PVC wall covering 1 to 2mm thick as per design and finish having fiber backing for sound Sqm 950.00 2787.25 2647888.00

insulation. Covering to be pasted on Mdf base with adhesive as approved by manufacture. Material should

be fire resistance as per ISO 105-B02 > grade 8 All complete as per engineer in charge

13 MR - 57 Providing & fixing 6 mm thick GRIHA rated lacquered glass with flat polished edge fixed to 5.5 mm thick Sqm 16.42 4335.72 71192.52

plain MDF board backing with neutral silicone and/or double-sided adhesive pads etc. ,including

polishing/MTG all complete as per the drawing & directions of engineer-in-charge. 6.0 mm thick

14 MR - 57 Providing & fixing 6 mm thick mirror with flat polished edge fixed to 5.5 mm thick plain MDF board backing Sqm 34.56 4335.72 149842.48

with neutral silicone and/or double-sided adhesive pads etc. ,including polishing/MTG all complete as per

the drawing & directions of engineer-in-charge. 6.0 mm thick

15 MR - 58 Providing & fixing commercial grade wall paper of approved shade to MDF/Gypsum board/POP Punning sqm 950.00 1858.16 1765252.00

base backing which have 100% washable, scratch resistance, peel proof, and fire retardant properties,

including preparation on the punned surface for receiving the wall paper, adhesive as per the manufacturer

specification, all complete as per the drawing & directions of engineer-in-charge( Base backing to be paid

16 MR - 59 Providing and fixing electroplating SS PROFILE of colour and design as per engineer in charge Metre 3736.71 708.04 2645741.00

17 9.40.1.2 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and Metre 2987.77 271.75 811926.00

priming coat on unexposed surface etc. complete : 2nd class teak wood:50 x 20 mm

18 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the sqm 2743.00 262.70 720585.00

surface even and smooth complete.

19 MR Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per sqm 2742.61 484.20 1327970.17

manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one

coat of Special primer applied @ 0.75 ltr /10 sqm

20 MR Providing and applying two or more coats of Textured Paint/ Surface Coating of approved make and shade sqm 113.40 807.00 91513.80

over walls etc. after preparing the surface with a coat of primer and 6 mm thick plaster of paris punning to

give a smooth and even surface etc. complete. base price 85 per sqft

21 13.116 Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade sqm 2622.58 3049.00 7996243.00

texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat

is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove

excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with

special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry

for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

CLA Digitally signed by AMITNBCC

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine

wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without

22 MR -60 Providing and fixing Roller Blind system consisting of a coated aluminium tube of 38 mm diameter of sqm 244.62 2787.25 681817.10

approved colour with provision of fabric clamping. The Fabric is rolled up and down through a chain drive

system with built in drive gear and an over run brake system. The side brackets are universal type suitable

both for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape aluminium tube

with provision to lock the fabric.The rate shall be inclusive of all the necessary material,required hardware,

labour, transportation, necessary for the complete execution of the item . basic price 180 Sqft

23 MR -61 Providing and fixing motorized Roller Blind system with remote consisting of a coated aluminium tube of 38 sqm 174.96 5030.53 880141.53

mm diameter of approved colour with provision of fabric clamping. The Fabric is rolled up and down through

a chain drive system with built in drive gear and an over run brake system. The side brackets are universal

type suitable both for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape

aluminium tube with provision to lock the fabric.The rate shall be inclusive of all the necessary

material,required hardware, labour, transportation, necessary for the complete execution of the item .

24 MR -62 Providing & Fixing 3M & equivalent Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL- Sqm 238.66 1316.20 314119.03

effect film to reproduce Sand-blasting effect on glass with customized designs, thickness of 2 mil (0.05mm)

without adhesive & 3M & equivalentil (0.8)with adhesive having minimum tensile strength of 3.5

pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7

kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs

(indoors) must be endorsed by Electronically/computer plotter cut. Applied on glass and other rigid, clear

substrates. (partitions, doors, windows etc.) Available in 5 colours

Total Carried Over to Abstract for Sub Head: 7.00 Wall Finshes Work : 15715353.00 22776400.20

SH 8 REPAIRS TO BUILDING 0

1 14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the Sqm 150 670.95 100643 0

patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based

polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of

Engineer-In-Charge.

Total Carried Over to Abstract for Sub Head: 8.00 Repairs To Building : 100643 0

SH 9 METAL WORK

1 10.25.2 Steel work welded in built up sections/ framed work, including cutting,vhoisting, fixing in position and Kg 120.00 172.6 20712

applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames,

guard bar, ladder, railings, brackets, gates and similar works

2 10.16.3 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, Kg 100 194.4 19440

hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and

bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes

Total Carried Over to Abstract for Sub Head: 9.00 Metal Work : 40152 0

SH 10 WATER PROOFING

INTEGRAL CEMENT BASED TREATMENT

1 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement

slurry mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253

kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

22.5 The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and sqm 70.80 617.05 43687

masonry with polymer mixed slurry.

Total Carried Over B215:B216to Abstract for Sub Head: 10.00 Water Proofing : 43687 0

CLA Digitally signed by AMITNBCC

SI.NO Ref Description Units Rate Rate Amount

1 Main Table Providing and Placing Main TAble of Size 2000x2100x750.MAIN WORKTOP Size 2400x900x740, ERU Each 10 130,249.81 1,302,498.05

1200x450x610mm- Main worktop - Made of 43mm Thick (±1) combination of commercial ply and particle

board with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick

veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) commercial ply with Leatherette wrapped around top

surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel

is made of 43mm Thick (±1) combination of commercial ply and particle board with top veneer face coated

with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of

18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with

leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and

closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit

modesty panel is made of 43mm Thick (±1) combination of commercial ply and particle board with top

veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining

construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-

12823:1990, Edge banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-

laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded

with matching 2 mm thick PVC lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of

18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping. Door is fixed with soft closing hinges and handle is

provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER

BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB power points, 1 HDMI

connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

2 Backunit The Back Unit shall be . It shall be made of 25mm thick MDF –combination of commercial ply and particle Sqm 180 22,273.20 4,009,176.00

board and veneer face coated with clear lacquer confirming to IS-14587:1998 with 0.4 mm PVC membrane

pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam

mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. customised

3 Main chair Providing & placing high back chair.SEAT ASSEMBLY : Each 10 75,750.80 757,508.00

The seat is made up of 12mm thick MR Grade plywood, layered with pocket spring core, super soft foam of

32 kg/m3 density and edging foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over

foam sub-assembly and upholstered in natural leather or leatherette.BACK ASSEMBLY :

The back assembly is made up of a gombination of pinewood members, 12mm thick MR Grade plywood and

2mm thick cardboard, layered with slab stock foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet

is placed over foam sub-assembly and upholstered in natural leather or leatherette.ARMPAD ASSEMBLY :

The armpad assembly is made up of 6mm thick MR Grade plywood fixed with MS powder-coated brackets,

layered with foam of 60 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly

and upholstered in natural leather or leatherette.4. CENTER TILT WITH MULTI POSITION LOCK MECHANISM:

The mechanism is designed with the following features:

360° revolving type

3 position locking

Tilt tension adjustmentPNEUMATIC HEIGHT ADJUS/MENT: The Class 4 pneumatic height adjustment has ar

stroke of 10 ÷ 0.3 cm.6. PEDESTAL ASSEMBLY :

The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black

color-coated internal surface. It is fitted with 5 castors and has a pitch-center diameter of 67.5#0.5 cm

(77.51.0 cm with castors).

7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black polyamide.

4 Visitor Chair Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5- Each 20 45,530.45 910,609.00

114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in

5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type,

front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt

angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat

depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism

housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to

suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The

pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in

plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

FURNITURE CLA Digitally signed by AMITNBCC

5 Waiting Sofa Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x Each 10 42,000.00 420,000.00

2 seator 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of

supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK

FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per

IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

6 Waiting Sofa Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x Each 20 29,832.15 596,643.00

1 seator 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of

supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK

FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per

IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

7 Center table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for Each 10 25,114.45 251,144.50

fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per

IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

8 Side table Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern Each 10 20,500.00 205,000.00

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built

1 Main Table Providing and Placing Main TAble of Size 2000x2100x750.MAIN WORKTOP Size 2700x900x740, ERU Each 9 162,570.55 1,463,134.95

1200x450x610mm- Main worktop - Made of 43mm Thick (±1) combination of commercial ply and particle

board with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick

veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) commercial ply with Leatherette wrapped around top

surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel

is made of 43mm Thick (±1) combination of commercial ply and particle board with top veneer face coated

with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of

18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with

leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and

closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit

modesty panel is made of 43mm Thick (±1) combination of commercial ply and particle board with top

veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining

construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-

12823:1990, Edge banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-

laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded

with matching 2 mm thick PVC lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of

18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping. Door is fixed with soft closing hinges and handle is

provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER

BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB power points, 1 HDMI

connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

2 Backunit The Size of the Back unit shall be made up of commercial ply duly finished with veneer & final finish by PU Sqm 162 24,748.00 4,009,176.00

coating , laqured glass , louver. Below storage shall be provided with wooden shutters & the upper left &

right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be

of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. with

provision for furniture lighting customized

FURNITURE CLA Digitally signed by AMITNBCC

3 Main chair Providing & placing high back chair.SEAT ASSEMBLY : Each 9 90,682.50 816,142.50

The seat is made up of 12mm thick MR Grade plywood, layered with pocket spring core, super soft foam of

32 kg/m3 density and edging foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over

foam sub-assembly and upholstered in natural leather or leatherette.BACK ASSEMBLY :

The back assembly is made up of a gombination of pinewood members, 12mm thick MR Grade plywood and

2mm thick cardboard, layered with slab stock foam of 28 kg/m3 density. A 200GSM soft touch fibre fill sheet

is placed over foam sub-assembly and upholstered in natural leather or leatherette.ARMPAD ASSEMBLY :

The armpad assembly is made up of 6mm thick MR Grade plywood fixed with MS powder-coated brackets,

layered with foam of 60 kg/m3 density. A 200GSM soft touch fibre fill sheet is placed over foam sub-assembly

and upholstered in natural leather or leatherette.4. CENTER TILT WITH MULTI POSITION LOCK MECHANISM:

The mechanism is designed with the following features:

360° revolving type

3 position locking

Tilt tension adjustmentPNEUMATIC HEIGHT ADJUS/MENT: The Class 4 pneumatic height adjustment has ar

stroke of 10 ÷ 0.3 cm.6. PEDESTAL ASSEMBLY :

The pedestal is made of high-pressure die-cast polished aluminum with a buffed outside surface and black

color-coated internal surface. It is fitted with 5 castors and has a pitch-center diameter of 67.5#0.5 cm

(77.51.0 cm with castors).

7. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black polyamide.

4 Visitor Chair VISITOR CHAIR FOR CABIN Each 27 55,129.00 1,488,483.00

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for

25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU

Foam with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D)

ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the

Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-

Down adjustment has 8 position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel

inside.Arm top width adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment-

any position (4.0$0.5cm range).Armrest top is made up of high density PU molded over glass filled Poly-

amide inner.POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following

features:360° revolving type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be

operated in seating position.3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is

housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth

can be adjusted in sitting position. Seat depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK

SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism

assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5+0.5

cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height adjustment has an

adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish.

It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-center dia. TWIN WHEEL CASTOR:

5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheel

Diameter and assembled to pedestal.

5 Waiting Sofa 3Seater Providing and placing sofa of size 1820mm (W)x 840mm (D)x760(H) . Pure Leather Upholstery -Pigmented Each 9 89,389.50 804,505.50

Durable and ergonomically perfect for seating. The top grains of leather is clearly visible which adds to the

aesthetics S Spring Webbing- Provides bouncing back action for floating feeling.Construction- Made of solid

wood frame with ply cross section which is moisture , termite and borer resistant. Adequate treatment of

wood initiated to enhance longevity and maintain robustness.PLY - 12 mm, PLY - 6mm flexiply , Paper board

3mm , webbing 2 inch , Zigzag Spring - 3.8mm Comfort- The seat is made of soft foam of density 28 kg/m3

which enhances comfort and cushioning with sinking feeling. Ground Elevation- Equipped with legs, the sofa

is elevated to allow a level of ground clearance.

FURNITURE CLA Digitally signed by AMITNBCC

6 Waiting Sofa Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x Each 18 33,774.00 607,932.00

1 seator 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of

supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK

FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per

IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

7 Center table Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for Each 9 31,091.80 279,826.20

fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per

IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

8 Side table Overall size of 600mm(L)600mm(D)x450mm(H)Designed for the modern Each 9 20,500.00 184,500.00

minimalist with a need for handy, compartmentalized storage.• Tabletop of durable, toughened glass with a

digitally back-printed Skyline pattern creates a sleek, modern look.• A strong, knockdown construction built

1 Main Table Providing in place of main table with overall size of table 1650 x 1550 x 750mm. The main table shall be of Each 9 45,491.85 409,426.65

size 1650 x 750 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick

commercial ply – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane

pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire

management. The ERU top is made of 25 mm thick commercial ply one side pre-laminate board confirming to

IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick

commercial ply one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane

pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick

Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC

lipping. Drawer fronts made of 25 mm thick commercial ply one side pre-laminate board with 0.4 mm PVC

membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM

long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam

mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

2 backunit Supplying of side storage unit of officers having dimension 1190WX 450DX 740H:Overall size of hinge door Each 18 20,000.00 360,000.00

unit is 1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION &

MATERIAL Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with

metal cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy

polyester powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk

bent metal tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester

powder of 50± 10 microns thickness. DOOR & DOOR OPENING two door opening for all other width of 1150

W.The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing

laminate on the other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels

for easy interchange of shelf height as required. Fixed shelves along with adjustable shelves provided only in

case of 4.0 feet height units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load

capacity for each shelf is 40kg maximum. SKIRTING OPTION- The skirting units are provided with 150mm high

skirting made of 1.0 mm thick C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10

micros thickness. LEVELER-Screw type adjustable leverer with plastic base provides vertical adjustment for

floor unevenness and levelling of units.BACK PANELS Back panels are made of 18mm thick pre-laminated

boards with options of decorative as well as fabric finishes. 2.5 height units consists of single back panel

whereas 4.0 height and 4.5 height units consist of split back top panel and split back bottom panels separated

by an Aluminium extrusion. LOCKING MECHANISM- 3-way nickel plated wooden furniture lock is provided for

effective and positive locking of doors. HANDLE- Aesthetically appealing recessed handles of Aluminium

extrusion are provided for easy opening and closing.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO

18001:2007 certified.

3 Main chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat Each 9 25,000.00 225,000.00

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should

made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using

polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat

shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished

aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment

shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is

operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio

Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall

dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal

below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/-

FURNITURE CLA Digitally signed by AMITNBCC

4 visitor chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat Each 18 25,095.00 451,710.00

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should

made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using

polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat

shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished

aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment

shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is

operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio

Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall

dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal

below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/-

5 WORK STATION Supplying of Recta workstation of size 1200 X 600x 750 with KBPT .Providing DESK based modular Each 9 25,200.00 226,800.00

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with

perforated metal modesty in between are connected to the understructure with the help of PDC Connectors

to provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA.

Wire Management : Metal powder coated power box with wire raiser+D56 is given to pull wires from the

floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop

above power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk

CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge

banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing

central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be

GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

6 WORKSTATION CHAIR The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat Each 9 20,500.00 184,500.00

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should

made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using

polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat

shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished

aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment

shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is

operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio

Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall

dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal

below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/-

D ROTATIONAL DR -

FURNITURE CLA Digitally signed by AMITNBCC

1 Main Table Providing and Placing Main TAble of Size 2000x2100x750.MAIN WORKTOP Size 2400x900x740, ERU Each 3 95,570.55 286,711.65

1200x450x610mm- Main worktop - Made of 43mm Thick (±1) combination of commercial ply and particle

board with top veneer face coated with clear lacquer. All edges are edge banded with matching 1mm thick

veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) commercial ply with Leatherette wrapped around top

surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top panel and drawer unit modesty panel

is made of 43mm Thick (±1) combination of commercial ply and particle board with top veneer face coated

with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is of

18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm thick particle board with

leatherette on top surface.Drawer unit is provided with soft closing channels for smooth opening and

closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open storage unit

modesty panel is made of 43mm Thick (±1) combination of commercial ply and particle board with top

veneer face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining

construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-

12823:1990, Edge banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-

laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded

with matching 2 mm thick PVC lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of

18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping. Door is fixed with soft closing hinges and handle is

provided for ease of opening.Also lock is provided on side panel for security.ACCESS FLAP WITH POWER

BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2 USB power points, 1 HDMI

connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

2 Backunit The Back Unit shall be . It shall be made of 25mm thick MDF –combination of commercial ply and particle Sqm 32.4 22,273.20 721,651.68

board and veneer face coated with clear lacquer confirming to IS-14587:1998 with 0.4 mm PVC membrane

pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam

mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. customised

3 Main chair Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded Each 3 55,750.80 167,252.40

plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded from polurethane,

and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest

support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The

armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be

designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground and

contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the

range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height

adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch

centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel

diameter and assembled to pedestal.

4 Visitor Chair Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5- Each 9 40,500.00 364,500.00

114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in

5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type,

front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt

angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat

depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism

housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to

suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The

pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in

plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

FURNITURE CLA Digitally signed by AMITNBCC

5 Waiting Sofa Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x Each 3 38,882.65 116,647.95

2 seator 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of

supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK

FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per

IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

E ITO and ddo - -

1 Main Table Providingin place of main table with overall size of table 1800 x 1800 x 750mm. The main table shall be of size Each 12 75,949.95 911,399.40

1800 x 750 x 750mm. The side unit shall be 1000 x 500 x 750mm. The table is made of 25 mm thick MDF –

one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top.

Soft closing access flap within-build power box are provided on work surface for wire management. The ERU

top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC

membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board

confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of

25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick

MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is

BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is

325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.

Pedestals are provided with lock for security.

2 backunit The Back Unit shall be of CUSTOMIZED. It shall be made of 25mm thick MDF – one side pre-laminate board Sqm 100.8 21,000.00 2,116,800.00

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of

25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Storage is provided with lock for security.

3 Main chair Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded Each 12 55,000.00 660,000.00

plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded from polurethane,

and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest

support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The

armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be

designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground and

contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating

position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be

integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back

frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the

range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height

adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast

polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch

centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel

diameter and assembled to pedestal.

4 Visitor Chair Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5- Each 24 25,600.00 614,400.00

114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in

5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type,

front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt

angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat

depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism

housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to

suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The

pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in

plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

FURNITURE CLA Digitally signed by AMITNBCC

5 Waiting 2 Seater Sofa Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x Each 24 38,500.00 924,000.00

855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of

supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK

FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of

supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be

made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per

IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm

dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded

assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

F WORK STATION - -

1 Main Table Supplying of Recta workstation of size 1200 X 600x 750 with KBPT .Providing DESK based modular Each 72 32,500.00 2,340,000.00

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with

perforated metal modesty in between are connected to the understructure with the help of PDC Connectors

to provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA.

Wire Management : Metal powder coated power box with wire raiser+D56 is given to pull wires from the

floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop

above power box cut out for accessing switches.Worktop mounted metal modesty made from 0.8 mm thk

CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge

banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing

central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be

GREENPRO, SCS IAQ, GRIHA, BIFMA certified.

2 Main chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat Each 72 35,500.00 2,556,000.00

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should

made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using

polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat

shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished

aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment

shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is

operated with button. Armtop is made up of PU molded over plastic inner. The mechanim shall be Active Bio

Synchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. Overall

dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair - 70.5 cm as measured from pedestal

below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance / variations shall be within +/-

G CONFERENCE - -

FURNITURE CLA Digitally signed by AMITNBCC

1 BOARD ROOM Providing and Placing in position Conference table for 24 seater having 12 Nos of 2 Seater Modules of size Each 1 227,288.25 227,288.25

1350mm X 600mm X 740mm . Worktop- Made of 25mm thick PLY BOARD FINISHED IN VINEAR AND CLEAR

PU POLISH one side pre-laminate board conforming to IS-14587:1998 with 0.4mm PVC membrane pressed

on to top and having chamfered edge.access flap is provided for easy access to wires and cables.Modesty

consist of 18mm Thick PLY Board finished with 4 mm thick approved vineer in PU clear polish as per desired

approved shade conforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for connecting

panels together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated twin

board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has

a knock-down construction.An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder

coated(DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module

plate is provided below worktop. Cutout on top with two piece injectionmoulded plastic part polymer

component is fitted to pull out audio,video cables ontoworktop and connect devices charger to power socket

2 Main chair HIGH BACK CHAIR FOR CABIN Each 1 60,682.50 60,682.50

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT HIGH BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for

25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU

Foam with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D)

ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the

Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-

Down adjustment has 8 position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel

inside.Arm top width adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment-

any position (4.0$0.5cm range).Armrest top is made up of high density PU molded over glass filled Poly-

amide inner.POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following

features:360° revolving type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be

operated in seating position.3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is

housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth

can be adjusted in sitting position. Seat depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK

SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism

assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5+0.5

cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height adjustment has an

adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish.

It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-center dia. TWIN WHEEL CASTOR:

5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheel

Diameter and assembled to pedestal.

3 Chair VISITOR CHAIR FOR CABIN Each 42 45,129.00 1,895,418.00

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide.-POSTURE

PERFECT FULL BACK CHAIR: STANDARD LEATHER Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45+2 kg/m°, and hardness load 16 ÷ 2 kgf as per IS 7888 for

25% compression. Seat SIZE: 45.5cm. (D) x 52.4cm. (W).BACK ASSEMBLY: The Cushioned back is made of PU

Foam with Polypropylene Injection molded.Plastic Inner.HIGH BACK SIZE: 50.5 cm. (W) x 61.8 cm. (D)

ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the

Aluminum Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-

Down adjustment has 8 position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel

inside.Arm top width adjustment - Any position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment-

any position (4.0$0.5cm range).Armrest top is made up of high density PU molded over glass filled Poly-

amide inner.POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following

features:360° revolving type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be

operated in seating position.3-position Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat depth adjustment is

housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth

can be adjusted in sitting position. Seat depth adjustment range is of 5.0$0.5 cm.ADJUSTABLE BACK

SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down mechanism

assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5+0.5

cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height adjustment has an

adjustment stroke of 13.0$0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing finish.

It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷ 0.5cm pitch-center dia. TWIN WHEEL CASTOR:

5 Nos. twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheel

Diameter and assembled to pedestal.

H Meeting room - -

1 Meeting room Providing and placing in position meeting table. Size 3600mmx 1500mmx 740mm. Worktop shall be made Each 1 85,129.00 85,129.00

from 25mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having

chamfered edge. Soft closing dual access flap provided for access to power supply and data cables. The

Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and

approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised

aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics.The product has a

knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated

(DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8

module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for

mounting Audio Visual Cables(eg. HDMI,VGA-A,etc). The product must be UL Greenguard certified.Complete

all as per the direction of Engineer in Charge.

FURNITURE CLA Digitally signed by AMITNBCC

2 Meeting chairs Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5- Each 12 25,500.00 306,000.00

114cm. Seat height shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic

outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance

polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of

compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of

PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with

pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather

and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01

cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in

5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type,

front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt

tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt

angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black

powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat

depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism

housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to

suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The

pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in

plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

I LOUNG AND cafeteria and reception

1 Round table The overall size of the meeting table is 1200 dia.he top shall be made up of 25mm thick pre laminated Each 4 30,000.00 120,000.00

partical board with 2mm PVC edge band. Leg: shall be made up of high pressure aluminum die casted 20

degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of

725mm length to get 750mm table height, it shall acts as vertical structural support member, connected by a

horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs

through a high pressure Aluminium diecast connectors.The OEM shall ISO 9001, BIFMA Level 2 certification &

IGBC gold certified manufacturing facility.

2 Round table chair The overall size of chair height shall be 770mm, Depth 640mm and Width shall be 620mm. The lounge chair Each 16 22,500.00 360,000.00

seating height shall be 440mm. The chair understructure shall have 4 legs that should be interconnected with

each other through frame. The understructure of the chair shall be made from solid wood i.e properly

treated & seasoned kiln dried beach wood, finished with clear synthetic PU coating for the best resilence and

high durability. The chair understructure should be 1.6mm thickenss swaged tube.The legs shall be in angular

design & thicker on the top & thinner on the bottom side. Understructure shall powder coated upto 40 to

60microns.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

3 3 seater sofa The overall size of the sofa shall be 2350 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly Each 1 69,000.00 69,000.00

from the combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The

polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in

back construction along with the webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth

shall be 525mm (+/- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that

shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be

formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its

bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the

leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment

friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be 450-475 gms

per meter having abrasion resistance of more than 50K rubs high quality polyester fabric.The OEM shall ISO

9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

4 single seater sofa The overall size of the sofa shall be 850 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly Each 2 33,000.00 66,000.00

from the combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The

polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in

back construction along with the webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth

shall be 525mm (+/- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that

shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be

formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its

bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the

leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment

friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be 450-475 gms

per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall ISO

9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

5 Center table The overall size of glass table shall be 1200L x 600W x 425H. The table top shall be made of 8mm thick Each 3 25,000.00 75,000.00

toughned glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to

protect from streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

6 Side Table The overall size of glass table shall be 600L x 600W x 505H. The table top shall be made of 8mm thick Each 2 15,000.00 30,000.00

toughned glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to

protect from streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

J Library And Lounge

FURNITURE CLA Digitally signed by AMITNBCC

1 3 seater sofa The overall size of the sofa shall be 2350 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly Each 4 69,000.00 276,000.00

from the combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The

polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in

back construction along with the webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth

shall be 525mm (+/- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that

shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be

formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its

bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the

leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment

friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be 450-475 gms

per meter having abrasion resistance of more than 50K rubs high quality polyester fabric.The OEM shall ISO

9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

2 single seater sofa The overall size of the sofa shall be 850 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly Each 8 33,000.00 264,000.00

from the combination of treated pine wood of 20-25mm thick & neem based plywood sheets. The

polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in

back construction along with the webbing belts. Seat height should be 440mm (+/- 10mm) and seat depth

shall be 525mm (+/- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that

shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be

formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its

bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the

leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment

friendly to enable powder coating to the thickness of 50-80 microns. The fabric used shall be 450-475 gms

per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall ISO

9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

3 Center table The overall size of glass table shall be 1200L x 600W x 425H. The table top shall be made of 8mm thick Each 4 25,000.00 100,000.00

toughned glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to

protect from streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

4 Side Table The overall size of glass table shall be 600L x 600W x 505H. The table top shall be made of 8mm thick Each 6 15,000.00 90,000.00

toughned glass. The understructure shall be made of 19mm SS round tube. Leg shall be provided ABS shoe to

protect from streched.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

5 library rack The overall size shall be 1500 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated Each 4 36,000.00 144,000.00

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking faciltity should be

provided for safe storage of documents. The prelaminated board used shall be of E1 norms. The OEM shall

ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

1 Full Height Storage The overall size shall be 1500 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated Each 8 39,000.00 312,000.00

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking

faciltity should be provided for safe storage of documents. The prelaminated board used shall be of E1

norms. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

1 Full Height Storage The overall size shall be 1500 x 450 x 1800 (WDH) mm. Top shall be made up of 18mm thick pre laminated Each 16 39,000.00 624,000.00

particle board and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. 4 Shutters to be provied for

uper & lower compartment. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. Locking

faciltity should be provided for safe storage of documents. The prelaminated board used shall be of E1

norms. The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified manufacturing facility.

M WORK STATION AREA STORAGE

FURNITURE CLA Digitally signed by AMITNBCC

1 Workstation area Supplying of side storage unit of officers having dimension 1190WX 450DX 1200 H:Overall size of hinge door Each 136 31,836.00 4,329,696.00

storage (1200X450) unit is 1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION &

MATERIAL Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with

metal cladding of 1.0 mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy

polyester powder of 50±10 microns thickness. TOP OPTIONS- The Storage units are provided with 11mm thk

bent metal tops made of 1.0 mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester

powder of 50± 10 microns thickness. DOOR & DOOR OPENINGtwo door opening for all other width of 1150

W.The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing

laminate on the other side. SHELVING- Height wise adjustable shelf mounting holes provided on side panels

for easy interchange of shelf height as required. Fixed shelves along with adjustable shelves provided only in

case of 4.0 feet height units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load

capacity for each shelf is 40kg maximum. SKIRTING OPTION- The skirting units are provided with 150mm high

skirting made of 1.0 mm thick C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10

micros thickness. LEVELER-Screw type adjustable leverer with plastic base provides vertical adjustment for

floor unevenness and levelling of units.BACK PANELS Back panels are made of 18mm thick pre-laminated

boards with options of decorative as well as fabric finishes. 2.5 height units consists of single back panel

whereas 4.0 height and 4.5 height units consist of split back top panel and split back bottom panels separated

by an Aluminium extrusion. LOCKING MECHANISM- 3-way nickel plated wooden furniture lock is provided for

effective and positive locking of doors. HANDLE- Aesthetically appealing recessed handles of Aluminium

extrusion are provided for easy opening and closing.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO

18001:2007 certified.

2 Storage room wall side Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It Each 48 26,800.00 1,286,400.00

storage should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield

strength) and all other components shall have a thickness of 0.9mm. These components shall be made of

CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three

way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which

shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller

with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Plenty of colour options and shelving options shall be available.

N COMPACTOR ROOM

1 2 Way Compactor Each 160 55600 8,896,000.00

Construction:- All components like front mechanism box, shelvings, clading sheet etc. shall be made out of

superior quality of CRCA sheets. It shall consist of storage units of 450mm deep, movable and bolted to

undercarriage that rolls on the channels firmly embedded to the ground. The size of storage body shall be:

width 915 mm, depth 450 mm and a height of 1980 mm (overall variance +/- 50 mm) including the storage

body height with undercarriage The main body should be rigid knock down construction is made of out of

Side /tack/top Panels made up of minimum 0.8mm thick CRCA steel. Each body block should consists of one

single fixed unit, one double mobile one single mobile unit and add on as per site conditions and each unit

should have 5 loading levels formed by 4 nos of adjustable shelves. The storage body units shall be bolted to

the undercarriage. The shelf panel of storage unit should be made of 0.8mm thick CRCA steel having UDL of

40-50 Kg per shelf. The shelves should be mounted on support brackets & its level should be adjustable.

There should be 4 adjustable shelves per body giving 5 loading levels. The under carriage should be made

with HR sheet min 2.5 min suitably fabricated using welding to take the loads. The OEM shall have IGBC gold

rated factory certification. The MSU should be running on a guidetrack of size 28 mm M.S. round with

necessary bracing/channel and base plate. Rails should be 25 mm square bright bar. The bodies including

shelves and undercarriages should be given 7 tank antirust surface treatments and finished with powder

coating using epoxy polyester powder of 50-60microns. A centralized locking arrangement should be

provided through the locking stiffener mounted onto back of single last unit so that it gets locked on channels

when all the units are brought together. All the' units should be provided with chrome plated handles. All the

MSU should be provided with the features such as mechanical drive with a handle for mechanically assisted

drive mechanism consisting of a series of sprocket and chain mechanism for smooth movement of the

compactor with minimum effort. It should be fitted with safety guard which is to be engaged when entering

the common aisle. This should prevent from operating system when an individual is in the working aisle. The

guide track should be provided with an end stopper to avoid derailment of the units. It should be provided

with the label holders.The OEM shall ISO 9001, BIFMA Level 2 certification & IGBC gold certified

manufacturing facility.

FURNITURE CLA Digitally signed by AMITNBCC

1 Reception AND ASK Providing and Placing Reception TAble of Size as Per Site WORKTOP - Main worktop Made of 43mm Thick Each 2 115,900.00 231,800.00

Desk (±1) combination of MDF and particle board with top veneer face coated with clear lacquer. All edges are

edge banded with matching 1mm thick veneer lipping.LEATHER PAD:Made of 18mm Thick (±1) MDF with

Leatherette wrapped around top surface. This leather pad is fixed to main top panel.DRAWER UNIT:Top

panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board

with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching

lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on top surface.Drawer unit is provided with soft closing

channels for smooth opening and closing.Drawer unit is secured with side central lock.OPEN STORAGE

UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1) combination of MDF and

particle board with top veneer face coated with clear lacquer. All thickness edges are edge banded with

matching lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and

approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC

lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty is fitted with

aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is

fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side panel

for security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal

Sockets, 2 USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT

2 Reception Chair The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat Each 4 35,000.00 140,000.00

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should

made up of back outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using

polyester mesh fabric with high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat

shall be (W)-51.0cm x (D)-49.0cm. The supprot spine should made up of high pressure die cast polished

aluminium. Armrest is having two adjustment, Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment

shall be provided in aluminium structure of armrest which is connected to aluminium back spine and is

operated with button. Armtop is made up of PU molded over plastic inner. The mechanism shall be Active

BioSynchro Mechanism. The mechanism of chair shall have following features:360 degree revolving type,

Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of variable tilt

angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder

coated. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel

castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The

twin wheel castors shall be injection moulded in black polypropylene. The lumbar support assembly should

consists of lumber spine(material-glass fiber filled nylon) which is fixed to Aluminium back spine. The neckrest

assembly consists of upholstered neckrest inner(material-poly propylene) with moulded polyurethane foam

and polyster fabric. upholstered inner shall be fixed to neck rest cover. neckrest shall be fixed to back

assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of

Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm. Seat

height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

3 STORAGE The Back Unit shall be of CUSTOMIZED. It shall be made of 25mm thick MDF – one side pre-laminate board Sqm 8.4 22,000.00 184,800.00

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of

25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of

opening. Storage is provided with lock for security.

P PANTRY - -

1 MR Modular kitchen - Under counter storage cabinets: Sqm 30.6 22,000.00 673,200.00

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18mm thick ISI marked HDHMR, all ply to be

laminated with 0.8mm laminate. All shelves should be supported on approved quality SS pins and shall be

adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thick

with laminate on both sides with 18mm wide 2mm thick PVC edge banding. All Shutters finished in high gloss

acrylic of approved. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable

legs which will be covered with PVC skirting in brushed aluminum finish attached by hardware of skirting. The

unit shall be fixed to the floor/ wall/ slab using metal screws of appropriate size and rawl plugs. Only front

face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and

payment. Cabinet boxes size would be varies from 400x560x710mm to 1000x560x710mm (approx.) and join

together as per site requirements etc.

2 MR Modular Kitchen - Overhead storage wall units: Sqm 32.4 25,000.00 810,000.00

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with

openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked HDHMR BOARD. All ply

to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and shall

be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm

thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high

gloss acrylic of approved. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size

and raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for

measurement and payment. Cabinet boxes size would be varies from 400x560x710mm to 1000x560x710mm

(approx.) and join together as per site requirements etc.

FURNITURE CLA Digitally signed by AMITNBCC

3 MR Providing and fixing with metal sides and quadro channels each 77 5,500.00 423,500.00

4 MR Providing and fixing baskets each 8 6,000.00 48,000.00

5 MR Supply, Installation, Testing and Commissioning of 100 l fridge nos 2 17,940.00 35,880.00

6 MR Supply, Installation, Testing and Commissioning of 250 l fridge nos 2 32,775.00 65,550.00

7 MR Supply, Installation, Testing and Commissioning of 400 l fridge nos 2 68,425.00 136,850.00

FURNITURE CLA Digitally signed by AMITNBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD , NEW DELHI

ABSTRACT OF COST

SI.No. DSR-2022/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

1.0 MR Providing and fixing 393mm undermount bar sink in matte black

including painting of fittings and brackets, cutting and making good

the walls wherever required. White Vitreous China Wash basin size EACH 2 ₹ 28,000.00 56000.00

approx 550x400 mm including , nuts, bolts and gasket and bottle

trap etc complete.

2.0 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and Each 10 574.30 5743.00

geyser points of approved quality conforming to IS:8931 15mm

3.0 18.21.2.1 Providing and fixing uplasticised PVC connection pipe with brass Each 2 97.75 195.50

unions : 45 cm length , 15 mm nominal bore

4.0 MR-24 Providing and fixing counter top mounted Sink mixture mixture Each 2 9476.00 18952.00

including inner fitting and all fitting as required

5.0 MR-25 Supply installation, testing and commissioning of water cooler with Each 2 89607.43 179214.86

Inbuilt RO purification .Cooling capacity shall be 60 liter & 80 liter

shall be storage capacity.Its should have 7 stages purification

process,fully automatic,rectangular tank with Forced fin and tube

condenser,Non-corrosive SS-304 outer body,Food-grade SS-304

stainless steel inner tank (18/8 or 18/10),PUF

insulation,Reciprocating compressor with R22 Refrigerant.Water

outlet temp is aprrox 17 deg c ,Operating power supply 230 + 10%

V AC,50 Hz,1 PH,No of Cold water Faucet-2.

TOTAL FOR SANITARY INSTALLATION 5939.00 254167.00

PLUMBING WORK CLA NBCC

Digitally signed by AMIT

ABSTRACT OF COST

SI.No. DSR-2022/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

B) WATER SUPPLY AND INTERNAL DRAINAGE SYSTEM

1 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and

making good the same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work, including cutting chases and making good the

a) 18.8.1 15 mm nominal dia Pipes Mtr. 20 497.80 9956.00

b) 18.8.2 20 mm nominal dia Pipes Mtr. 20 537.60 10752.00

c) 18.8.3 25 mm nominal dia Pipes Mtr. 10 627.25 6272.50

d) 18.8.4 32 mm nominal dia Pipes Mtr. 18 739.30 13307.40

2 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete

as per direction of Engineer in Charge.

Internal work - Exposed on wall

a) 18.7.1 15 mm nominal dia Pipes Mtr. 2 286.80 573.60

b) 18.7.2 20 mm nominal dia Pipes Mtr. 10 335.00 3350.00

c) 18.7.3 25 mm nominal dia Pipes Mtr. 10 401.55 4015.50

d) 18.7.4 32 mm nominal dia Pipes Mtr. 5 518.75 2593.75

e) 18.7.5 40 mm nominal dia Pipes Mtr. 15 702.95 10544.25

e) 18.7.6 50 mm nominal dia Pipes Mtr. 30 934.15 28024.50

3.00 MR Providing and fixing low noise insulated Polyproplene piping

system as per DIN EN 12056 and DIN1986-100 with 3 layer pipe

made of External layer -PP, middle layer-Mineral reinforced PP,

Internal layer-PP. push-fit type, food safe, having high impact and

stiffness, offering sound levels of not more than 10 dBA as per DIN

4109 at a flow rate of 2 l/s and having pipe ring stiffness as per

1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560,

density of pipe = 1.9 g/cm3, elongation break 50% and tensile

strength 20 N/mm2,Coefficient of linear expansion 0.09 mm/mK

with all necessary fittings fitted with factory fitted lip ring including

cutting and making good the walls, floors, R.C.C. work etc or also

incluiding painting with ordinary cement based paint for external

installation. (including MS structural support & U clamps as

a) 110 OD mm dia Pipes Metre 50 1811.00 0.00 90550.00

b) 75 OD mm dia Pipes Metre 80 1166.00 0.00 93280.00

4.00 MR Providing and fixing PP white Trap with minimum 50mm water seal

with rubber seal on inlet to push fit hopper for indirect waste

a) 110 mm inlet & 110 mm outlet Long ht Each 2 1505.00 0.00 3010.00

a) 17.36.2 Providing and filling the joints with spun yarn, cement slurry and Each 10 163.45 1634.50

cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : (

100 mm dia pipes)

TOTAL FOR DRAINAGE 91024.00 186840.00

PLUMBING WORK CLA NBCC

Digitally signed by AMIT

ABSTRACT OF COST

SI.No. DSR-2022/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

GRAND TOTAL (A+B) 96,963.00 441,007.00

GRAND TOTAL (A+B) 96,963.00 441,007.00

PLUMBING WORK CLA NBCC

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF

PROJECT:PROPOSED ELECTRICAL ESTIMATE FOR CONSTRUCTION OF INCOME TAX OFFICE

NAME OF WORK - INTERNAL ELECTRIFICATION WORK WITH AC LIGHTING AND WITHOUT LIGHTING CONTROL

Sr.N Rate as per

Sch.No. Particulars Qty Unit Amount Rate Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 1.10.3 conduit, with modular switch, modular plate, suitable GI box 507 Nos. 1,467.00 743,769.00 - -

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

3 1.12 recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS 3330 Meter 334.00 1,112,220.00 - -

PVC insulated copper conductor single core cable for loop earthing as

Wiring for circuit/ submain wiring alongwith earth wire with the

4 1.14 following sizes of FRLS PVC insulated copper conductor, single core - - -

cable in surface/ recessed medium class PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper braid and

protected with PVC sheath in the existing surface/ recessed steel/ PVC

conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing following modular switch/ socket on the

7 1.24 existing modular plate & switch box including connections but - - -

excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet 160 Each 148.00 23,680.00 - -

b 1.24.7 TV socket outlet 3 Each 148.00 444.00 - -

c RA-1 RJ45 socket cat 6 with shutter 180 Each - 475.83 85,649.99

Supplying and fixing two module stepped type electronic fan

8 1.25 regulator on the existing modular plate switch box including 12 Each 369.00 4,428.00 - -

connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith

9 1.27 modular base & cover plate for modular switches in recess etc. - - -

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6 A

modular socket outlet and 5/6 A modular switch, connections etc. as

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. as required.

Supplying and fixing brass batten/ angle holder including

connection etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Installation of exhaust fan in the existing opening, including

17 1.50 making good the damage, connection, testing, commissioning - - -

etc. as required.

Extra for fixing the louvers/ shutters complete with frame for a

exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing

surface/ recessed Steel/ PVC conduit as required.

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed PVC conduit,

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6

21 1.56 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. 180 Each 676.00 121,680.00 - -

as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve

including connections, painting etc. as required.

Supplying and fixing PVC batten/ angle holder including

connections etc. as required.

Digitally signed by AMIT

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with

connections, testing and commissioning etc. as required.

c 2.10.5 Triple pole and neutral 5 Each 1,228.00 6,140.00 - -

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB),

26 2.14 having a sensitivity current 30 mA in the existing MCB DB - -

complete with connections, testing and commissioning etc. as

Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve, miniature

circuit breaker suitable for inductive load of Four poles in the existing

MCB DB complete with connections, testing and commissioning etc. as

required. Similar to Legrand DX3 AC MCBs or equivalent.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

DSR 2022 thick including accessories, and providing masonry enclosure

5.6 with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

30 5.11 pipe from earth electrode including connection with G.I. nut, 30 Meter 706.00 21,180.00 - -

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre

below ground as strip earth electrode, including connection/

32 terminating with nut, bolt, spring, washer etc. as required. 600 Meter 972.00 583,200.00 - -

(Jointing shall be done by overlapping and with 2 sets of brass

nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

33 5.18 for loop earthing along with existing surface/ recessed conduit/ 1 Meter 42.00 42.00 - -

submain wiring/ cable as required.

SITC of Glasso Deep Recessed LED Downlight

with maximum 12Watts Lumens 1500 cob base having non Intergral

isolated driver with 2kv surge protection 230V with CRI>90, Beam Angle

15Deg , 24Deg , 36Deg and 60Deg color temperature

3000K/4000K/5700K, IP20, IK04, operating voltage range 140-270Vac,

temperature -10° to 45°C, PF>0.95, THD<10%, product

34 MR efficacy>110lm/W, SDCM<5, 80 Each - 4,130.00 330,400.00

L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall

be luminaire beam

angle, drivers efficiency >86%, internal surge protection of >2.5kV, LED

make - Bridgelux,

Seoul, Osram, Cree, The manufacturer shall provide LM79, LM80,

TM21, Photoboilogical

safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers.

SITC of Fixed Deep Eye Recessed LED Downlight

with maximum 12Watts 1500 LM cob base having non Intergral isolated

driver with 2kv surge protection 230V with CRI>90, color temperature

3000K/4000K/5700K, IP20, IK04, operating voltage range 140-270Vac,

operating temperature -10° to 45°C, PF>0.95, THD<10%, product

efficacy>100lm/W, SDCM<3,

L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall

be luminaire beam angle 60Deg, drivers efficiency >86%, internal surge

protection of >2.5kV, LED make - Bridgelux,

Seoul, Osram, Cree, The manufacturer shall provide LM79, LM80,

TM21, Photoboilogical

safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers.

SITC of Down Light Round adjustable recessed 12Watts LED Double

optical system with lens and reflector to improve the visual comfort

complete with LED lamp. (White Fixture with White Reflector). Life time

50.000h . Body in die-cast Aluminium Complete with LED Lamp

.CRI>90,3000K/4000K/5700K, IP20, IK04, operating voltage range 140-

270Vac, operating temperature -10° to 45°C, PF>0.95, THD<10%,

L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall

be luminaire beam angle 36Deg, drivers efficiency >86%, internal surge

protection of >2.5kV, LED make - Bridgelux,

Seoul, Osram, Cree, The manufacturer shall provide LM79, LM80,

TM21, Photoboilogical

safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers.

Digitally signed by AMIT

SITC Recessed downlightwith HPE (High-Performance Efficiency) with

LED (Light Emitting Diode), system power: 12 W, Luminous flux of

luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature of

4000 K, Neutral white, CRI > 80, 230V constant current driver, 70% of

37 MR luminous flux after 50,000 operating hours; energy-efficient LEDs, direct 10 Each - 2,596.00 25,960.00

light emission, housing in die-cast aluminium, Polyester powder white

coloured coat applied over a 5-stage pre-treatment trim, prismatic diffuser

for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

SITC of Fixed Deep Eye Recessed LED Downlight

with maximum 7Watts 800 LM cob base having non Intergral isolated

driver with 2kv surge protection 230V with CRI>90, color temperature

3000K/4000K/5700K, IP20, IK04, operating voltage range 140-270Vac,

operating temperature -10° to 45°C, PF>0.95, THD<10%, product

efficacy>100lm/W, SDCM<3,

L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall

be luminaire beam angle 60Deg, drivers efficiency >86%, internal surge

protection of >2.5kV, LED make - Bridgelux,

Seoul, Osram, Cree, The manufacturer shall provide LM79, LM80,

TM21, Photoboilogical

safety as per IEC 62471, RoHS complaint, BIS both for fixture and drivers.

SITC of 2'X2' recessed mounted Luminaire with Maximum 36 Watt with

Lumen output of 3600 lumen. The product should be SMD based and

have non integral isolated driver with 2KV inbuilt surge protection.

39 MR THD<10%, PF >0.9,Product should have life class of 50K burning hour at 200 Each - 7,080.00 1,416,000.00

L70 B50 parameter, Luminiare operating temp 0 D to 45D. Internal wiring

should have teflon coted multi strand wires and external wire should have

PVC coated multistrand wires.

SITC Magnetic Track Channel Lighting System features a high-grade

aluminum alloy body with a premium anodized or powder-coated finish,

ensuring durability and a sleek aesthetic. Available in customizable lengths

(1m, 2m, 3m, or as per project requirements), it comes in two elegant

40 MR finishes: Matte Black and Matte White. Designed for flexibility, it operates 30 Each - 5,605.00 168,150.00

on 48V DC and supports multiple mounting options—surface mounted,

recessed, or suspended with adjustable suspension lengths. Accessories

include end caps and versatile connectors (linear, L-shape, T-shape, X-

shape), making it ideal for modular and dynamic lighting solutions.

SITC Magnetic Track Spot Module

A versatile lighting solution designed for highlighting wall art, showcasing

products in showrooms, or accentuating interior spaces with flexibility.

41 MR Equipped with an energy-efficient LED lamp, this module provides 60 Each - 5,310.00 318,600.00

focused illumination to enhance visual appeal. Its elegant brown finish

adds a touch of sophistication, seamlessly blending with various decor

styles. Perfect for creating dynamic and impactful lighting in any setting.

SITC Magnetic Track Linear Module

A versatile lighting solution designed for highlighting wall art, showcasing

products in showrooms, or accentuating interior spaces with flexibility.

42 MR Equipped with an energy-efficient LED lamp, this module provides 20 Each - 5,310.00 106,200.00

focused illumination to enhance visual appeal. Its elegant brown finish

adds a touch of sophistication, seamlessly blending with various decor

styles. Perfect for creating dynamic and impactful lighting in any setting.

SITC Magnetic Track Spot Module Constructed from high-grade

aluminum alloy with an BRONZE anodized or BROWN powder-coated

finish it ensures durability and aesthetic appeal. The module integrates

energy-efficient LED technology with a power rating of [Specify Wattage,

e.g., 5W, 10W, 15W], delivering high luminous efficacy and a CRI of ≥90

for superior color rendering. It offers adjustable beam angles ([Specify,

e.g., 15°, 24°, 36°]) and a range of color temperatures (3000K, 4000K,

6000K), providing flexibility for various lighting needs. Designed for 48V

DC systems optional anti-glare attachments and supports seamless

integration with magnetic connectors

44 MR SITC I Connector 80 Each - 1,003.00 80,240.00

45 MR SITC L Jointer 10 Each - 1,003.00 10,030.00

SITC Non - Dimmable Power supply

46 MR Inbuilt Supply In Track. 30 Each - 5,841.00 175,230.00

SITC Customised Skylight

Ceiling with highquality PVC film

ceiling installation for LED And Fabric Only Beam Angle:120°, included

with Non Dimmable Power Supply.

SITC Wooden Floor Lamp is a versatile and elegant lighting fixture

designed for office applications It features a premium wooden finish

natural with visible wooden grains brass base The adjustable head allows

for precise light placement, making it perfect as a reading lamp or a

focused work light in any office setting. Integrated LED color temperature

49 MR SITC Customised Decorative Table Lamp with Shade 20 Each - 33,630.00 672,600.00

SITC Wooden Table Lamp is a versatile and elegant lighting fixture

designed for office applications It features a premium wooden finish

natural with visible wooden grains brass base The adjustable head allows

for precise light placement, making it perfect as a reading lamp or a

focused work light in any office setting. Integrated LED color temperature

51 MR SITC Customised Glass Hanging set for 3pcs 20 Each - 21,830.00 436,600.00

Digitally signed by AMIT

SITC Customised Acoustic 450mm Hanging Light is a functional and

decorative lighting fixture designed to enhance acoustic performance while

providing high-quality illumination. Ideal for offices, meeting rooms, and

52 MR commercial spaces, it combines sound-absorbing properties with modern 5 Each - 32,450.00 162,250.00

lighting aesthetics. Diameter: 450mm Color Temperature: Available in

3000K (Warm White), 4000K (Neutral White), and 6000K (Cool White)

CRI: ≥90 Suspended with adjustable steel cables (length customizable)

SITC Customised Acoustic 450mm Hanging Light is a functional and

decorative lighting fixture designed to enhance acoustic performance while

providing high-quality illumination. Ideal for offices, meeting rooms, and

53 MR commercial spaces, it combines sound-absorbing properties with modern 12 Each - 34,810.00 417,720.00

lighting aesthetics. Diameter: 550mm Color Temperature: Available in

3000K (Warm White), 4000K (Neutral White), and 6000K (Cool White)

CRI: ≥90 Suspended with adjustable steel cables (length customizable)

SITC Customised Decorative Swing Arm Black Metallic Light is a stylish

and functional lighting fixture designed to offer flexibility in lighting

direction. this lamp features a sleek brass / black metallic finish, offering

54 MR both aesthetic appeal and durability. Swing Arm: Heavy-duty metal for 9 Each - 11,210.00 100,890.00

stable movement and long-lasting performance. Arm Length: Adjustable

10Watts Color Temperature: Available in Warm White (3000K), Neutral

White (4000K), and Cool White (6000K) In-line On/Off switch

SITC Customised Linear Light 35mm Wide Modular System features an

innovative design with anti-glare spots and diffused linear lighting for

superior performance and visual comfort. The system combines linear

diffused light (1547mm) with a Blanker 500mm spot, offering tool-free

installation and future replacement capabilities. Mounting Options:

Suspended, Surface-mounted, or Recessed Size Options: 2ft, 4ft, 6ft, 8ft,

55 MR and 12ftLinkable: Ultra-long single-end power for seamless continuous 30 Each - 14,750.00 442,500.00

runs Power Supply: Inbuilt for easy integration Diffuser: Snap-fit design

for easy maintenance Power: 30W (linear) + 10W (spot)Voltage: 230V

Color Temp: 3000K/4000K/5700K CRI: >80 Beam Angle: Diffused

Efficacy: >100lm/W Operating Voltage: 140-270V Operating Temp: -

10°C to 45°C IP Rating: IP20, IK04 Surge Protection: >3.5kV LED:

Bridgelux, Seoul, Osram, Cree

SITC Customised High-Efficiency Inward Curved Deep Linear LED

Fixture is designed for glare-free, high-output lighting ideal for office and

general applications. Featuring a deep inward curve (Min 15-20mm), it

ensures uniform light distribution without hotspots. Mounting Options:

Suspended, Surface-mounted, or Recessed Size Options: 2ft, 4ft, 6ft, 8ft,

56 MR and 12ft Linkable: Allows seamless continuous runs Power Supply: 30 Each - 13,570.00 407,100.00

Inbuilt for easy integration Diffuser: Snap-fit for maintenance Aesthetic:

Premium white finish Specifications: Power: 40W Voltage: 230V Color

Temp: 3000K/4000K/5700K CRI: >80 Beam Angle: Diffused Efficacy:

>100lm/W Operating Voltage: 140-270V Operating Temp: -10°C to 45°C

IP Rating: IP20, IK04 Surge Protection: >3.5kV LED: Bridgelux, Seoul,

SITC Customised High-Efficiency Inward Curved Deep Linear LED

Fixture is designed for glare-free, high-output lighting ideal for office and

general applications. Featuring a deep inward curve (Min 15-20mm), it

ensures uniform light distribution without hotspots. Mounting Options:

Suspended, Surface-mounted, or Recessed Size Options: 2ft, 4ft, 6ft, 8ft,

and 12ft Linkable: Ultra-Long Single-End Power in Allows seamless

continuous runs Power Supply: Inbuilt for easy integration Diffuser: Snap-

fit for maintenance Aesthetic: Premium wooden finish with visible grains

Specifications: Power: 40W Voltage: 230V Color Temp:

3000K/4000K/5700K CRI: >80 Beam Angle: Diffused Efficacy:

>100lm/W Operating Voltage: 140-270V Operating Temp: -10°C to 45°C

IP Rating: IP20, IK04 Surge Protection: >3.5kV LED: Bridgelux, Seoul,

SITC Customised Decorative Swift Linear in Brushed Brass Finish

58 MR aluminium , available beam angle diffused, with hanging kit, complete 5 Each - 31,270.00 156,350.00

with Led strip with diffuser and Non Dimmable power supply

59 MR SITC Decorative Lights 2 Each - 53,100.00 106,200.00

SITC Slim Shadow Hanging Light boasts a sculptural design inspired by

the elegant curve of a rotated sine wave, creating a mesmerizing interplay

of light and shadow. Crafted from premium aluminum with a satin matte

finish, it produces concentric light patterns, enhancing the ambiance with

its striking visual effect.Diameter: 400mm Material: High-quality

aluminum with satin matte finish Design: Sculptural, wave-inspired form

Lighting Effect: Subtle contrasts of light and shadow, creating beautiful

concentric patterns

Digitally signed by AMIT

SITC Deep Recessed Round Ceiling Light/Wall Light cover for lower

luminance made of die-cast-aluminium with black powder-coating finish

and black decoration ring; ON-OFF Driver; System Power 30W;

measurement Ø450mm .A recessed kit facilitates installation, allows you

to customize the depth. color temperature 3000K/4000K/5700K, IP20,

IK04, operating voltage range 140-270Vac, operating

61 MR temperature -10° to 45°C, PF>0.95, THD<10%, product 15 Each - 21,830.00 327,450.00

efficacy>110lm/W, SDCM<5,

L70B50@50000hrs, LED binning as per ANSI Bin C78.377A, 110° shall

be luminaire beam

angle, drivers efficiency >86%, internal surge protection of >2.5kV, LED

make - Bridgelux,

Seoul, Osram, Cree, The manufacturer shall provide LM79, LM80

62 MAIN L.T PANEL - -

Design, Manufacturing, Supply, Commissioning & Testing of Main LT

Panel. The panel will be totally enclosed type with, free standing, floor

mounted, indoor duty, dust & vermin proof, , front operated, electrical

panel fabricated from 2 mm thick M.S. Sheet as per specifications &

drawing laid in this document and will be complete with the main and - -

auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB,

interconnection wiring, earth bus and will be powder coated finish with 50

micron thickness.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have

AMF facility to achieve electrical interlocking, synchronizing, buscoupler

switching, auto operation of incommer and bus coupler, auto start of D.G.

Sets, auto D.G. running by pre set timing, auto changeover etc and having

following incomming and outgoing Air Circuit Breakers, FSU's as per the

drawing and specification. Each incoming breaker will have

microprocessor based releases and all outgoing breaker will have

minimum electrostatic releases over 250A & thermal magnetic release

below 250A. The Panel will be made as per detailed specifications &

drawings forming part of this document. Fault level of panel shall be 35

250Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no. - -

100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no. - -

100Amp. 16KA FP ATS - -

1 Nos. 320 Amp FP busbars of aluminium alloy as per SLD. - -

1 Nos. 160 Amp FP busbars of aluminium alloy as per SLD. - -

32Amp. 10KA FP MCB 6 No. - -

63Amp. 10KA FP MCB 6 No. - -

63Amp. 10KA FP MCB+300mAmp FP RCCB 5 No. - -

100Amp. 10KA FP MCCB 1 No. - -

INSTRUMENTS - -

2 sets of multifunction meter with parameter

current,voltage,KWH,KVAH,Power factor on incoming from transformers - -

with RS 485 port.

2 Sets of phase indicating lights (RYB) with protection fuses (one set for

each incoming breaker).

2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming

2 Sets auto trip indicating lamp . - -

63 UPS INPUT PANEL - -

Design, Manufacturing, Supply, Commissioning & Testing of Main LT

Panel. The panel will be totally enclosed type with, free standing, floor

mounted, indoor duty, dust & vermin proof, , front operated, electrical

panel fabricated from 2 mm thick M.S. Sheet as per specifications &

drawing laid in this document and will be complete with the main and

auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB,

interconnection wiring, earth bus and will be powder coated finish with 50

micron thickness.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have

AMF facility to achieve electrical interlocking, synchronizing, buscoupler

switching, auto operation of incommer and bus coupler, auto start of D.G.

Sets, auto D.G. running by pre set timing, auto changeover etc and having

following incomming and outgoing Air Circuit Breakers, FSU's as per the

drawing and specification. Each incoming breaker will have

microprocessor based releases and all outgoing breaker will have

minimum electrostatic releases over 250A & thermal magnetic release

below 250A. The Panel will be made as per detailed specifications &

drawings forming part of this document. Fault level of panel shall be 35

100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no. - -

1 Nos. 160 Amp FP busbars of aluminium alloy as per SLD. - -

100Amp. 10KA FP MCB 3 No. - -

INSTRUMENTS - -

1 sets of multifunction meter with parameter

current,voltage,KWH,KVAH,Power factor on incoming from transformers - -

with RS 485 port.

1 Sets of phase indicating lights (RYB) with protection fuses (one set for

each incoming breaker).

1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming

1 Sets auto trip indicating lamp . - -

64 UPS OUTPUT PANEL - -

Digitally signed by AMIT

Design, Manufacturing, Supply, Commissioning & Testing of Main LT

Panel. The panel will be totally enclosed type with, free standing, floor

mounted, indoor duty, dust & vermin proof, , front operated, electrical

panel fabricated from 2 mm thick M.S. Sheet as per specifications &

drawing laid in this document and will be complete with the main and

auxiliary bus bars, multimeter, indication lamps, CT's, protection MCB,

interconnection wiring, earth bus and will be powder coated finish with 50

micron thickness.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have

AMF facility to achieve electrical interlocking, synchronizing, buscoupler

switching, auto operation of incommer and bus coupler, auto start of D.G.

Sets, auto D.G. running by pre set timing, auto changeover etc and having

following incomming and outgoing Air Circuit Breakers, FSU's as per the

drawing and specification. Each incoming breaker will have

microprocessor based releases and all outgoing breaker will have

minimum electrostatic releases over 250A & thermal magnetic release

below 250A. The Panel will be made as per detailed specifications &

drawings forming part of this document. Fault level of panel shall be 35

100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-2 no. - -

BUS COUPLER - -

100Amp. 16KA FP With S/C, U/V, E/F Protection MCCB-1 no. with

electrical interlocking of incomer

2 Nos. 125 Amp FP busbars of aluminium alloy as per SLD. - -

63Amp. 10KA FP MCB 8 No. - -

INSTRUMENTS - -

2 sets of multifunction meter with parameter

current,voltage,KWH,KVAH,Power factor on incoming from transformers - -

with RS 485 port.

2 Sets of phase indicating lights (RYB) with protection fuses (one set for

each incoming breaker).

2 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming

2 Sets auto trip indicating lamp . - -

Supply Installation testing and commissioning of Star Delta Starter

Suitable for 35-50 KW starter with Potential free contact, type-2

coordination and metering etc as required for AHU including all necessary

Supply Installation testing and commissioning of Star Delta Starter

Suitable for 10-15 KW starter with Potential free contact, type-2

coordination and metering etc as required for Axial Flow Fan including all

necessary items..

Supplying and installing following size of perforated painted with powder

coating M.S. cable trays with perforation not more than 17.5%, in

67 convenient sections, joined with connectors, suspended from the ceiling - -

with M.S. suspenders including bolts & nuts, painting suspenders etc. as

a 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness 100 Meter 543.00 54,300.00 -

b 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness 20 Meter 777.00 15,540.00 -

Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm

balance stranded conductor,XLPE Insulated,cores laid up, PVC tape

innersheathed,unarmoured/Armour(Aluminium wire for single core up to

68 MR 70 sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 - - -

sqmm, 3x10 sqmm & balance all galvanised steel strip),extruded PVC

Type ST2 sheathed,650/1100V grade as per IS 7098(Part 1) 1988

a RA-9 3.5CX25Sq.mm Cable Cu. Flex. - 2,331.58 -

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated

and PVC sheathed / XLPE CU conductor cable of 1.1 KV

grade as required.

Laying and fixing of one number PVC insulated and PVC

70 7.8 sheathed / XLPE power cable of 1.1 KV grade of following size - - -

on cable tray as required.

b 7.8.2 Above 35 sq. mm and upto 95 sq. mm Meter 92.00 - - -

c 7.8.4 Above 185 sq. mm and upto 400 sq. mm 50.0 Meter 185.00 9,250.00 - -

Raceway Work - - -

Supply Installation testing and commissinoning of GI racewayin floor

similar to Legrand or equivalent.

a RA-13 100 mm x 38 mm - 1 compartment 200 Meter - 1,436.05 287,210.38

b RA-14 150 mm x 38 mm - 1 compartment 80 Meter - 1,881.57 150,525.61

c RA-15 300 mm x 38 mm - 3 compartments 80 Meter - 3,378.02 270,241.73

72 Supply and Fixing bracket (GI) - - -

Supply Installation testing and commissinoning of GI raceway riser in floor

similar to Legrand.

RA-19 Vertical - for 300 mm width raceways 90.00 Each - 2,513.16 226,184.55

Digitally signed by AMIT

Supply Installation testing and commissinoning of Junction box For direct

74 acess to cables at the intersection of raceways Supplied completely with - - -

base and cover plate (Lid)

Supply Installation testing and commissioning of OccuSwitch is a

movement detector with a build-in switch. It will switch off the lights in a

room or area when it is vacated and thus save energy. It can switch any

load up to 6 A and control an office area of around 20sqm for small

75 RA-23 movement (e.g. desk work) and around 50sqm for large movement (e.g. 42.00 Each - 4,324.94 181,647.31

walking). It is smart daylight sensing technology offers additional saving

through daylight override and daylight switching. similar to Philips Cat

Ref. LRM1071/10 - OccuSwitch Movement Detector or equivalent.

Fire Suppression System - -

2kg capacity seamless Alluminium cylinder Paso approved stored pressure

type clean agent fire extinguisher alongwith all necessary fitting filled with

clean agent FK-5-1-12 complete having operating pressure between 15

bar etc. as required UL & FM listed gas.

SITC of Pneumatic Heat detection tube red color made by special

modified polyamide (PA), UL and LPCB standard, having burst

77 MR temperature 100°C to 120°C, inner diameter 4 mm, outer diameter 6 mm, 40.0 Meter - 2,454.40 98,176.00

pressurized with nitrogen at 15 bar pressure for automatic detection and

suppression system

SITC of End of line adapter along with pressure gauge working pressure

25 bar. UL approved.

SITC of End of Line Plug for automatic fire suppression System used for

79 MR fitting at tube end to terminate the point. Fitting made by brass nickel 2 Each - 6,442.80 12,885.60

plated material. UL approved.

80 MR SITC of Pressure Switch at 15 bars. UL approved. 2 Each - 11,658.40 23,316.80

SITC of Master Control Unit micro processor based 4 zone inbuilt GSM

dialer audio visual alarm control panel, 2NO/NC potential free relay

81 MR contacts discharge LED indicator, battery LED indicator, system status 2 Each - 25,311.00 50,622.00

indicator and AC power ON LED indicator with inbuilt battery backup

SITC Supply of 80 Itr. Cylinder PESO Approved, complete with valve

assembly and including necessary accessories like high pressure

manual release, Solenoid valve for actuation and Rigid Hose as required to

complete the system.(For UPS & Server Room)

84 MR SITC Cylinder Clamp 1.00 Nos - 3,776.00 3,776.00

SITC of Piping as required, Sch 40; ASTM A106 Gr B, as per flow

calculations for the specific hazard volume and stand to hold,

position & Support the Piping properly. Also including single cylinder

wall fixing barrackets with C chanel duly painted.

SITC of Piping as required, Sch 80; ASTM A106 Gr B, as per flow

calculations Maniflod pipe.

87 MR SITC ofDischarge Pressure Switch. 1.00 Nos - 8,850.00 8,850.00

88 MR SITC of Nozzles, 360 Deg / 180 Deg Throw. 8.00 Nos - 5,310.00 42,480.00

Amount after GST Multiplication factor on DSR Items @1.0633 7,199,569.96 13,686,983.81

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD OFFICE , NEW DELHI

ABSTRACT OF COST

NAME OF WORK -INTERIOR AND FINISHING WORK

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

1 Rectangular ductwork for AC WORK

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

vanes, hangers, supports etc. as per approved drawings and specifications of following sheet

thickness complete as required.

1.1 16.12.1.1 24 Gauge (thickness 0.63mm sheet) Sqm 160.0 1,080 172,800

1.2 16.12.1.2 22 Guage (thickness 0.80mm sheet) Sqm 110.0 1,263 138,930

1.3 16.12.1.3 20 Guage (thickness 1.0mm sheet) Sqm 80.0 1,381 110,480

1.4 16.12.1.4 18 Guage (thickness 1.25mm sheet) Sqm 60.0 1,836 110,160

Supply, installation, balancing and commissioning of fabricatedat site GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

vanes, hangers, supports etc. as per approved drawings and specifications of following sheet

thickness complete as required.

2.1 16.12.2.1 24 Gauge (thickness 0.63mm sheet) Sqm 670.0 1,058 708,860

2.2 16.12.2.2 22 Guage (thickness 0.80mm sheet) Sqm 420.0 1,229 516,180

2.3 16.12.2.3 20 Guage (thickness 1.0mm sheet) Sqm 277.0 1,629 451,233

2.4 16.12.2.4 18 Guage (thickness 1.25mm sheet) Sqm 145.0 1,793 259,985

3 Duct Insulation

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell

Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile

rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber

tape insulation complete as per specifications and as required.

4 Duct Accoustic Lining :

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded

glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600

mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated

aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX

compound etc. complete as required and as per specifications.

Grilles/Diffusers/Louvers/VCDs/FDs :

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with

aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without

volume control dampers with anti smudge ring & removable core.

Supply, installation, testing and commissioning of GI volume control duct damper complete with

7 16.13 neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. Sqm 3.0 7,046 21,138

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and

return air path as and where required of required sizes i/c control wiring,the damper shall be

motorized and spring return so as to close the damper in the event of power failure automatically

and open the same in case of power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. The damper shall also be closed in the event of fire

signal complete as required and as per specifications.

Supply, installation, testing and commissioning of single duct VAV Terminal unit with automatic

moterized volume control dampers, sensor, controller & actuator assembly, 24V transformer,

ON/OFF switch, hanger alongwith 2 x 1.5 sqmm control wiring & conduiting complete in all respect.

Supplying, fixing acoustic lining on wall and ceiling of AHU roomswith 50mm thick, density 32

kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made

10 16.22 of25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with Sqmtr 650.0 1,229 798,850

reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete

as required and as per specifications.

VENTILATION AND SMOKE EXTRACTION SYSTEM

11 MR Axial Fan for "Exhaust Air (Emergency)"

CLA Digitally signed by AMITNBCC

Supply installation, testing and commissioning of single piece long casing (Motor should

completely be accommodated inside the fan casing) Vane Axial Fan (multi piece casing are not

acceptable) in GSS/MS with powder coated, Al impeller with adjustable blade angles (Manually

Adjustable at Site), bird screen ,gravity louvers, fire retardent flexible connection, necessary nut

bolts and directly coupled TEFC Sq.cage induction motor (IE2) H Class insulation for Smoke Exhaust)

suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with required hardware etc. All offered fans

pitch angle shall be AMCA Certified & Listed on AMCA website (Interpolation of pitch angle shall not be

acceptable) and Fan Efficiency Grade ( Min FEG 71, lesser is not acceptable).Thickness of the casing shall

not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm –

4mm & Dia 1600 – 5 mm.

All fans after assembly shall be dynamically trim-balanced to ISO1940 and AMCA 204/3 - G2.5

Fan Casing should be provided with Special Designed Integral Straightening Vanes (Vanes

should be integral part of casing, it should not be provided separately as an accessory) to

reduced turbulence provide high performance & low noise level.

Fans for emergency application Tube axial are to be used.

Sound level for emergency operation it should not exceed 88 Db(A)@ 3 meter (Room

condition).Incase of not achieving sound , attenutor has to be added.

Outlet velocity of the fans should not exceed 18 m/s for emergency application.

Smoke and heat exhaust fans should be tested and certified for 250 Deg C for 2 hour in

accordance to standard 'BSEN12101-3:2015 from TUV SUD PSB Singapore or equivalent

internationally recognized fire laboratory

Emergency Operation

11.1 MR 20000 CFM @35 static pressure No. 2.0 396,091 792,182

Rectangular ductwork for VENTILATION AND SMOKE EXHAUST WORK

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

vanes, hangers, supports etc. as per approved drawings and

specifications of following sheet thickness complete as required.

12.1 16.12.2.1 24 Gauge (thickness 0.63mm sheet) Sqm 60.0 1,058 63,480

Supply, installation, testing and commissioning of Motorized(ON-OFF Type) duct mounted GI

13 16.14 volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for

integration within AHU room for exhaust duct

Supplying & fixing of powder coated extruded aluminium Return/Exhaust Air Grills with louvers but

without volume control dampers complete as required.

Supply, installation, testing and commissioning of anodised aluminium Fresh air/exhaust air

louvers with bird screen as per specifications and drawings.

1 1 VRV Out Door units :

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and

heating, having all hermetically sealed inverter type Scroll Compressor(s),

minimum two compressors for above 14 HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration

isolators, with suitable foundation etc. complete as required. The unit shall deliver

the rated capacity at AHRI Conditions and work even at 50°C ambient temperature

without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz

AC power supply. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and

IEER not less than 6.5. (Design should be got approval before execution from

engineer in charge)

Supply, installation, testing and commissioning of following minimum capacity 4-

way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX Copper coil, electronic

expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration

2 2 isolation, cord less remote control etc., suitable for operation on single phase 230 V

± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS System. The

cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and

19 Degree C WB temperature. fresh air provision compatible for Remote Operation

Supply,Installation,testing and commissioning of corded Cord type remote control Nos.

with thermostat, LED Display and internal wiring for Cassette

4 MR Supply,Installation,Testing & Commissioning of Y Joints-Indoors Nos. 18 5820.2 104763.6

5 MR Supply,Installation,Testing & Commissioning of Y Joints-outdoors Nos. 2 6627.1 13254.2

CLA Digitally signed by AMITNBCC

Supply, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant

piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type

6 5 hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O

tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular

sleeves sections of specified thickness as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 10 2450.0

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 140 46340.0

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 80 35680.0

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 140 82320.0

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 80 56560.0

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 99 85635.0

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick Rmt 110 121880.0

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick Rmt 67 82410.0

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick Rmt 55 71995.0

Supply installation testing commissioning Shielded Control Cables for VRV System

7 MR with necessary ISI mark Medium class rigid PVC pipes with necessary accessories

with termination in machine and control equipments.

7.1 (A) 2Cx1.5 Sq mm Shielded Armoured(for communication lead & remote ) Rmt 781 189.2 147765.2

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade

to be erected as directed of following size.

8.1 3C x 2.5 sq.mm FOR INDOOR UNIT POWER CABLE Rmt 220 210.5 46310

9 MR Drain Piping :

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

VRV Unit Panel-FOR OUTDOOR UNITS

10 MR Supply,installation,testing and commissioning

alised floor/wall mounted type made of 2 mm thick

steel sheet duly painted complete as per the

specifications and drawing and as detailed below :

1 no.160 Amps TPN MCCB incomer with KWH

meter, phase indicating lamps with control fuse &

toggle switch, voltmeter and selector switch, ammeter

with CTs and selector switch

4 nos. of 40 Amps TPN MCB outgoing for VRV OD units with star delta starter

4 nos. of 63 Amps TPN MCB outgoing for VRV OD units with star delta starter Nos. 1 222600.0 222600

Supply,installation,testing and commissioning of Providing and erecting

XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV.

to be laid on wall with necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cable.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

12 MR Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

Providing and fixing approved make Perforated C type cable tray. Made from sheet

steel. The cable tray should be single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing as per IS 2629/4759. with

13 max 17.5% perforation with coupler plate / Fish plate and GI hardware like nut -

bolt and washers etc. erection with necessary support( included) as per Specification

and as per instruction of engineer in charge..

14 MR Earthing :

Supply,installation,testing and commissioning of following double earthing continuity

conductor of Cu from Panels to respective equipment on surface or recess as per

drawings and specifications.

Amount after GST Multiplication factor on DSR Items @1.0633 8277358.56 3192362.40

CLA Digitally signed by AMITNBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF

PROJECT:PROPOSED ELECTRICAL ESTIMATE FOR CONSTRUCTION OF INCOME TAX OFFICE

NAME OF WORK - UPS SYSTEM

Rate as Applicable

Sr.No. Particulars Sch.No. Qty Unit Amount Rate Amount

1.0 SUB HEAD-I :-MODULAR UPS WITH Li-ion BATTERIES

60 KVA =60KW, IGBT/PWM technology based True Online double

conversion (1working + 1 stand By)and fully Microprocessor controlled

UPS system along with

• Make Delta DPH 80

• 3 Nos Module of 20 kva

• Frame size 80 kw

• Input Power Factor Unity 0.99

• Output Power Factor (1) KVA = KW.

• Efficiency 96.2% and 99% in Eco

• Warranty 1Years

• DC Breaker , DC Cable and other

• Li-ion batteries: - 1 string of 60 Ah / > 3.108 kWHr Battery (LG

Make) with each UPS with 10 years warranty on Batteries

(Back up calculation is done on 40 KW peak load).

Batteries with cell level monitoring and one PC to start

up the battery bank and monitoring.

UPS described as above MR Set 2 3,080,000.00 6,160,000.00

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD , NEW DELHI

ABSTRACT OF COST

WORK: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe

on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic

18.7 enamel paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68

2 degree centigrade with required accessories :

18.21.4 Concealed Sprinkler Each 218 1435.00 312830.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel

complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of

3 18.25 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT

female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as per

manufacturer's specifications.

Providing & fixing of CO2 High Pressure trolley mounted 6.5 kg Fire Extinguisher, filled with Co2 Gas as

per IS 15222, Gross Weight 23 Kg, empty weight 16.5 Kg, Control discharge mechanism fitted with 2

Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge

Time 25 Sec, Average Discharge is 95%, applicable on Class B, C and electrically started Fire, Internal

coating is not applicable & External coating is of enamel spray painting, Valve Confirm to IS 3224 ISI

Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to

IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 16018:2012 and ISI maked. Fire Rating: 55B

Fire Fighting CLA Digitally signed by AMIT NBCC

Providing and fixing of Water type cartridge operated 9 ltr. Fire Extinguisher. Applicable fire class

A,UTGS Pressure Gauge, Gross Weight 13 Kg, empty weight 5.3 Kg, Can Height 585mm, Diameter 180 ±

10mm, Discharge Time 35 Sec, Controllable discharge mechanism, Jet Range 7 Meters, Average

Discharge is 95%, Fire Rating- 3A, Can Construction : Deep drawn & CO2 Mig welded, CE Marked Valve

with inbuilt NRV & Safety Release Provision, Controllable discharge mechanism with EPDM Hose &

Nozzle, CO2 gas Cartridge of 60 gm. Internal Plastic Lining and External Coating - Pure Polyester Powder

coating (UV Resistant), Made up of 2 mm Sheet, As per IS 5683:2018 and ISI Marke

c) MR ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 5 4746.13 23730.63

Amount after GST Multiplication factor on DSR Items @1.0633 1281883.64 102947.38

Fire Fighting CLA Digitally signed by AMIT NBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD , NEW DELHI

ABSTRACT OF COST

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

1 MR Providing, fabricating and fixing of SS 1.5 inches of required size and shape with arrangement of screws Each 22 65,977.00 1451494.00

in the letters itself for mounting on the walls or pasting using 3M VHP Tape. Fixing complete as per

directions of the engineer. The Sizes would be calculated in Sqft as per Logo Design provided. Tentative

2 MR Providing, fabricating and fixing of 3D Acrylic Letters raised 1.5 inches of required size and shape with Each 2 35,977.00 71954.00

arrangement of screws in the letters itself for mounting on the walls or pasting using 3M VHP Tape. Fixing

complete as per directions of the engineer. The Sizes would be calculated in Sqft as per Logo Design

Tentative Size 42"X60"

3 MR NAME SIGNAGE CHANGEABLE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with textured wood finish pasted /White Each 30 1,967.00 59010.00

milky acrylic 3mm laser cut pasted on top with proper names/ Departments written using plottercut vinyl

or laser cut acrylic letters in approved colour.Inserting provision for changing names .Fixing provision using

3M VHP double sided tape as required.

Signage Size 12x5 inch

4 MR FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm acrylic with Evacuation Plan Printed Each 4 2,673.00 10692.00

on photoluminescent media and inserted between the two frames. Should be fixed on the wall using 4

Screw/ SS studs. Size 12 inch x 17 inch

4 MR FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made from acrylic sheet of 8 mm thickness Each 10 3,289.00 32890.00

laser engraved, Transformer to be inbuilt. Maintenance - free sealed nickel cadmium battery included •

120V/277V AC Operation • Crystal clear acrylic face panel• Engraved letters increase visibility • Anodized

aluminum faceplate • Field applied chevron directional indicators simplify installation • Long life, energy-

saving LED lamps • Dual-voltage 120V/277V AC Operation • UL listed. To be installed at stairs entry. Size

5 MR FIRE SAFETY SIGNAGE

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun board sheet at base with Each 10 535.00 5350.00

photoluminescent film self adhesive & colored vinyl ( Red/Green) Plotter cut and pasted on top. Both side

/ Single Side facing Complete including fixing on wall with screws and washers or hanging on ceiling with

GI chain/GI Bar complete as per technical specifications and directions of Engineer.

SIGNAGE CLA Digitally signed by AMIT NBCC

Photoluminescent signages

SIGNAGE CLA Digitally signed by AMIT NBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD , NEW DELHI

ABSTRACT OF COST

I.NO DSR DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

1 MR Rectangular FRP Planter(LP7A-24"X8"X10") Each 75 4,800.00 360000.00

2 MR Rectangular FRP Planter(LP7A-24"X10"X12") Each 75 5,600.00 420000.00

3 MR Round FRP Planter(LP9A-20"X20"X30") Each 75 7,500.00 562500.00

4 MR Round FRP Planter (LP9B-18"X18"X24") Each 100 4,500.00 450000.00

5 MR Artificial Vertical Garden on wall Each 28 8,500.00 238000.00

6 MR Ms Frame (Hanging) with Artificial hanging creeper Each 20 8,500.00 170000.00

Size : 3'-0"x6'-0" (Each)

7 MR Preserved Moss 1.5" THK Each 20 65,900.00 1318000.00

8 MR Plantation: Supply and installaion of Natural Plant with sand, fertilizer etc. as per the Each 325 1,200.00 390000.00

approval of client.

HORTICULTURE CLA Digitally signed by AMIT NBCC

Detailed Estimate

Proposed Office BuildingITAT

Name of Work: Access Control System Work.

DSR 2023 DSR-2023

Sr.No. Particulars Sch. No. Qty Unit Rate Amount

Supply, Installation, Testing and Commissioning of 2 Reader Intelligent IP based Controller with 32 bit

1 processor, 1,000 card holders, 1,00,000 transaction Logs Enclosure, Power supply and with all accessories to MR 1 Each 152119.70 152,119.70

finish the job.

Electromagnetic Lock (Single leaf)

2 Electromagnetic Lock (Single leaf), 600 lbs strength, LED Status Indicator including pair of Magnetic MR 14 Each 21830.00 305,620.00

Contact for each door position sensing for Access Control.

Emergency Door Release with Manual lock / key Switch

3 Emergency Door Release for individual door / turnstile / barrier, with break glass type switch, Double Pole MR 14 Each 12508.00 175,112.00

Single Throw (DPST), arranged in such a pattern so as to release the lock in case of emergency and also send

a signal to the monitor input of the controller.

4 Supply, Installation, Testing and Commissioning push botton door open switch for single and double door. MR 14 Each 12036.00 168,504.00

Supply, Installation, Testing and Commissioning IP based

5 Fingerprint Biometric Reader with built in Smart card Reader, Power supply with wiegand output fully MR 14 Each 33630.00 470,820.00

6 Supply, Installation, Testing and Commissioning Single door Magnetic Lock with Door Position Switch. MR 2 Each 10148.00 20,296.00

Supply, Installation, Testing and Commissiong of Access Control Software (PC based for interfacing and

programming) and with require all accessories to finish the job

SITC of PC Hardware with a minimum speicification of Intel i7 Quad Core Processor 7th Generation at mim

3.6 GHz , Intel HD Graphic, 8 GB or more of RAM, 500GB SATA Hard Drive for OS and ACS & TA

applications, Network Interface Card - 10/100/1000 MB, Dual Monitor Graphics card to support 2

multiplexed Monitors. DVD-R/W Microsoft® Windows® 8.1 / 10 Pro or Higher 64 bit

Supply & Laying of 8core 1.0 sq. mm ATC PVC insulated & sheated, twisted pair, Al shielded and overall

FR PVC sheathed cable in in existing 25 mm PVC/Steel Conduit.

Supply & Laying of 4core 1.5 sq. mm ATC PVC insulated & sheated, twisted pair, shielded and overall FR

PVC sheathed cable in existing 25 mm PVC/Steel Conduit.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including

11 painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit -

Face Recognition Terminal (FRT)

It should have industry standard Wiegand and OSDP interface with support for 37-bit format.

Display: 5 to 12" color capacitive touchscreen Display or better.

Network/Communication: Ethernet, RS485, USB, Wiegand and OSDP.

Other Communication: Built-in speaker.

Protocols supported: TCP/IP, Wiegand/OSDP, IPv4, HTTP, DNS, SSL

Authentication Type: FACE

Cyber security: 128/256-bit AES encryption or better.

MAC ID for Devices:

The MAC IDs of all components to be connected to the GAIL network, either through physical or wireless connection, must not originate from, nor

be registered in, a country sharing a land border with India, unless the vendor has obtained prior clearance from the Government of India.

Vendors must provide an undertaking from the OEM certifying that:

• The MAC IDs of the supplied equipment are not associated with or registered in any country sharing a land border with India.

• The components do not contain any hardware or software originating from entities in such countries, unless clearance has been obtained.

12 Documentary evidence in the form of the MAC ID registry information must be submitted to Central EIC before delivery of the FRT devices at

GAIL. Integration with existing FRT system, data upload as per the requirement etc.

Operating Temperature:20°C to 50°C (14°F to 131°F)

Humidity: 10% to 80% (non- condensing)

Ingress protection: Face Reader shall be IP65 rated.

Software for Face Recognition Terminal

The Face Recognition algorithm should have been evaluated by a recognized body such as MeitY or NIST (FRVT/FRTE/FATE) or BIS or a

laboratory accredited under ISO/IEC 17025 for ISO/IEC 19795 compliance .

A performance evaluation report for the algorithm must be submitted along with the bid.

• The bidders are required to provide certification from the OEM stating that the algorithm and version being deployed, as per the tender, is the same

or a higher version than that which was used during the aforementioned performance benchmarking.

FRT Software License

Software License(1 Year) for Face Recognition Terminal

CAT-6 Cable & Associated accessories required for installation

Amount after GST Multiplication factor on DSR Items @1.0633 23126.78 5,210,885.90

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD , NEW DELHI

ABSTRACT OF COST

NAME OF WORK - FIRE ALARM &PA

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1.00 FIRE ALARM

1.0 Supplying, installation, testing & commissioning of intelligent analog addressable EACH 256.00 2858.00 731648.00 0.00

17.2.4 photothermal detector complete with mounting base complete as required.

2.0 Supplying, installation, testing & commissioning of response indicator on EACH 114.00 276.00 31464.00 0.00

17.2.5 surface/recessed MS Box having two LED, metallic cover complete with all

connections etc as required.

3.0 Supplying, installation, testing & commissioning of intelligent addressable EACH 12.00 2726.00 32712.00 0.00

17.2.9 thermal detector with rate of rise cum fixed tempreature thermistor complete

with base as required.

4.0 Supplying, installation, testing & commissioning of fault isolator complete with EACH 35.00 3270.00 114450.00 0.00

base as required.

5.0 Supplying, installation, testing & commissioning of addressable fire control EACH 3.00 3003.00 9009.00 0.00

module complete as required

6.0 Supplying, installation, testing & commissioning of addressable phone control EACH 6.00 3267.00 19602.00 0.00

module complete as required.

7.0 Supplying, installation, testing & commissioning of intelligent addressable duct EACH 3.00 7814.00 23442.00 0.00

17.2.13 detector including suitable Photo detector complete with base as required.

8.0 Supplying, installation, testing & commissioning of addressable horn cum strobe EACH 15.00 3506.00 52590.00 0.00

complete as required.

9.0 Supplying, installation, testing & commissioning of addressable manual call point EACH 15.00 3871.00 58065.00 0.00

complete as required.

10.0 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller EACH 1.00 126411.00 126411.00 0.00

with USB, MP3 player (including 6 zone button paging station) with seamless

integration facility with main fire alarm panel for voice evacuation complete as

11.0 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated Meter 1738.00 173.00 300674.00 0.00

with annealed copper conductor having XLPE insulation, steel wire armouring &

FRLS outer sheath complete as required

12.0 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all EACH 599.50 53.00 31774.00 0.00

ancillaries and accessories like coupler etc. as required.

CLA Digitally signed by AMIT NBCC

13.0 Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs EACH 32.00 3870.00 123840.00

power Battery backup complete as required.

14.0 Supply, Installation, Testing and Commisioning of Loop Card capacity of 159 EACH 3.00 92150.00 276450.00

detectors For BMS Fire integration compatible with existing system

15.0 Supply, Installation, Testing and Commisioning of Interface Card for BMS fire EACH 3.00 55500.00 166500.00

integration compatible with exisiting system

16.0 Supply, Installation, Testing and Commisioning of repeater panel having 640 EACH 3.00 90000.00 270000.00

MR character liquid crystal with backlit control compatible with existing system

Note - item to be applicable in urban areas having directions for restricted hours

for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Fire Alarm : 1531841.00 836790.00

SH 2.00 PA SYSTEM

1.0 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker EACH 229.00 965.00 220985.00 0.00

complete as required.

1.0 Supplying, installation, testing & commissioning of digital audio amplifier 150 EACH 3.00 74598.00 223794.00

MR Watt, 25V rms operating at 240 Volt AC Supply complete as required.

1.0 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor

cable in the existing surface / recessed steel conduit of following pairs, cores and

size including connections and interconnections etc. as required.

17.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm EACH 1438.00 89.00 127982.00 0.00

1.0 Supplying, installation, testing & commissioning of Voice command keypad 6 EACH 1.00 81756.00 81756.00 0.00

zone, with microphone assembly complete as required.

Total Carried Over to Abstract for Sub Head: 2.00 Pa System : 430723.00 223794.00

Amount after GST Multiplication factor on DSR Items @1.0633 2086794.30 1060584.00

CLA Digitally signed by AMIT NBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF ITD OFFICE , NEW DELHI

ABSTRACT OF COST

NAME OF WORK -CCTV

SI.NO DSR UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

1 MR SITC of IP Vari Focal Dome IR Camera with mounting brackets: 1/2.8" Image Sensor; No's 36 12,500.00 450,000.00

Resolution: 1920X1080; Lens: Fixed Focal; f:2.8 to 12 mm; Iris: Fixed; Colour:0.1 [email protected]

B/W:0 lux (IR LED ON); Day/Night; WDR;Privacy Masking : 8 Zone ; Video

Intelligence:Tampering VMD, & Trip Zone; IR Distance: 30 Mtr; Shutter Speed : 1/30 ~

1/10000 sec or higher ONVIF S, Protocols : RTP/RTSP/TCP, RTP/RTSP/HTTP/TCP, RTP/UDP

RTSP/TCP, HTTP, HTTPS, FTP, SNTP, SMTP, Controlled Backlight compensation;

Connectivity:RJ45(10/100 BASE-T); POE; Video Streaming: Four;Edge Storage 256 GB :

Multiple Option; Protection: IP 67; IK10, Operating Temperature: -20 degree C - +55

degree C;Operating Humidity: 0% -90%. MTBF time 1,00,000 Hours (Report to be

Submitted) Certifications: CE,FCC,BIS/UL etc complete as required etc all complete

CCTV WORK CLA Digitally signed by AMIT NBCC

2 MR SITC of 64 Channel Rack mount NVR , H.264/H.265 compression, network incoming No's 1 415,250.00 415,250.00

throughput of 850 Mbps and 12MP recording resolution, time division multiplexing, real

time recording of multiple cameras, storing digitized and compressed images on internal

hard disk drives, fast search and retrieval either locally at the unit, or Graphical User

Interface (GUI), all connected cameras to be discovered and configured automatically,

simultaneous live view, record, play back, data transmission in real time, maximum

throughput of 400 Mbps, UHD 1920 ips, support H.264/H.265 compression, 2X – 12X

digital zoom in live view mode, 2X – 12X digital zoom in playback mode, time lapse,

event, time lapse + event, pre / post-event, panic recording schedule, recording bitrate

control mode: CBR and VBR, alarm, audio, motion, trip zone, video loss, text-in, system

event triggering, fan error, record failure, storage related alerts and alarm in error, email,

remote notification (call back) to remote work stations, mobile device push and SNS

(Twitter) notification, Time-lapse, Event log, Motion, Thumbnail, Text-in search options,

SSL, Password encryption options, network keyboardfor controlling the NVR and PTZ, 1

Gigabit Remote Client port, 4 Gigabit ports, ONVIF compliant , output interface 1 HDMI

(up to 4K), 8 internal SATA ports (10TB per SATA) with recording capacity up to 80 TB or

more , RAID support as 1, 5, 10 - user may choose & configure as per security needs on

internal SATA , redundant dual power supply ,2 USB for backup /upgrade, BIS certified,

internal Admin service, monitoring servics, Left object detection, compatible to AI

cameras, ANPR cameras for future., Support Bookmarking, Support SSL, privacy masking

and password support is required on exported videos, Failover services in 10:1mode etc

3 MR SITC of 10 TB Surveillance Hard Drive, With a workload rating of up to 180 TB/yr, built for No's 6 50,895.00 305,370.00

always-on, 24/7, high-definition surveillance systems etc all complete

4 MR SITC Redundant Server Intel I7 Xeon Quad Processor with 2 x 8GB RAM , 1 Tb HDD, TFT No's 1 275,750.00 275,750.00

Display , Keyboard, Mouse complete all accessories .as per specifications of this tender

etc complete as per specifications etc. all complete

IP CCTV and Suvilliance Solution 1,446,370.00

CCTV WORK CLA Digitally signed by AMIT NBCC

ABSTRACT OF COST

NAME OF WORK - EPABX AND TELEPHONE

SI.NO DSR CODE DESCRIPTION

UNIT QTY RATE DSR AMOUNT

1 MR Supply, Installation, Testing & Commissioning of Server based

Communication System with all the required Software licenses and

Hardware - IP-PBX/IP Telephony Communications Server: The IP Telephony

Solution shall support the following Services - Voice, Video, IM, Presence

and Audio Conference The IP Telephony Solution should support H.323 and

SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP

The IP Telephony solution should incorporate all licenses for the Phones and

Trunks Solution should support all Extensions from Day 1 with future

scalabilityupto 1000 users. Licenses for all Phones supplied should be

provisioned on Day1 Solution should support Hard 120 IP Phones,

Softphones, Video Phones, Extensions with necessary Licenses, Rack mount

architecture, complete as required and as per technical specifications.or its

equivalent specifications

2 MR Display size 8”; Portrait, 1280 x 800 pixel, Capacitive Touch with 24-bits

color depth, Touch Screen, Wideband audio available on all transducers,

handset, headset, and handsfree. USB flash drive for data transfer to and

from the device. Support is limited to USB flash drives with up to 32 GB of

storage. Multi-port USB hub, USB headset, Mouse, Keyboard, USB Camera,

Android devices (Support is only limited to charging the Android device.

Data transfer is not

supported). Up to 900 mA if using Class 4 (802.3at) PoE switch • Up to 100

mA if using Class 3 PoE switch, Bluetooth® 4.2 supporting High Speed (HS),

Low Energy (LE), and Enhanced Data Rate (EDR) functionality, Integrated

Bluetooth for pairing accessories, cordless handset and wireless headsets,

Dual Port RJ45, 10/100/1000 Mb, SIP, DHCP, DNS, LLDP (for Ethernet

interface only), TCP, TLS, HTTP / HTTPS, RTP / SRTP, RTCP / SRTCP, SNTP,

802.1x, VLAN (for Ethernet interface only), DSCP Layer 3 QoS, Includ

Licence.or its equivalent specifications.

Color display—2.8 inches x 2.1 inches (7.0 cm x 5.3 cm)—Diagonal width: 3.5

inches (8.8 cm)▪ 8 buttons with dual LEDs (red, green)▪ 4 softkeys▪ Hard

buttons for phone, messages, contacts, history, home, navigation

cluster,headset, speaker, volume, mute▪ LEDs for speaker, mute, headset,

message, history▪ 24 administrative buttons▪ Wideband audio in handset

and headset▪ Full duplex speakerphone ▪ Ergonomic hearing aid compatible

handset supports TTD acoustic coupler▪ Message waiting indicator▪ Mute

indicator with optional mute alerting▪ IC call alerting with 360-degree

visibility▪ Rich, classic, alternate, and downloadable ringtones▪ Dual-position

stand, optional wallmount stand▪ Gigabit Ethernet (10 / 100 / 1000) line

interface▪ Second Ethernet interface 10 / 100 / 1000 Mbps▪ PoE Class (IEEE

802.3af) registers as class 1 device and supports 802.3az▪ Optional AC to 5 Nos 20 47280 945600 0

volt adapter▪ Order Custom Bezels / Faceplates▪ SIP & H.323 protocol

support▪ Standards-based codec support: G.711, G.726, G.729A / B, G.722,

Opus.▪ Zero touch deployment via Device Enrollment Services Support▪

Supports the following languages: Arabic, Brazilian Portuguese, Simplified

Chinese, Dutch, English, Canadian French, Parisian French, German, Hebrew,

Italian, Japanese, Korean, Polish, Latin American Spanish, Castilian Spanish,

Thai, Turkish, and Russian

3 MR 2.8” (diagonal) color display—320 x 240 pixels, Multiple line phone with four

red / green line / feature indicators around display, 4 Context sensitive soft

keys, Hard buttons for phone, messages, contacts, history, home, navigation

cluster, headset, speaker, volume, mute, LEDs for speaker, mute, headset,

essage, history, Wideband audio in handset and wired headset, Full duplex

speakerphone & handset, Ergonomic hearing aid compatible handset

supports TTD acoustic coupler, Message waiting indicator, Mute key with

optional mute alerting, IC call alerting with 360-degree visibility, Dual-

position stand, optional wall-mount stand, Gigabit Ethernet (10 / 100 /

1000) line interface, Second Ethernet interface 10 / 100 / 1000 Mbps, PoE

Class (IEEE 802.3af) registers as class 1 device and supports 802.3az,

Optional AC to 5 volt power supply • SIP protocol support, Standards-based

codec support: G.722, Opus, Configurable via Web interface, Support for

HTTPS, TLS and SRTP for encryption, Recent Call Log (100 entries), Zero

touch deployment via Device Enrollment Services Support, Supports the

following languages: Dutch, English (UK & US), French, (Canada), French

(France), German, Italian, Japanese, Portuguese (Brazil), Simplified Chinese,

Spanish (Latin America), Spanish (Spain),Traditional Chinese, Includ

Licence.or its equivalent specifications

4 MR Supply, Installation,Testing and commisioning of IP phone license complete as required

Digitally signed by AMIT

S.No. Item Specifications Unit Qty Unit Price Total Price

Conference Room

Supply, Installation, testing and commissioning of 98" UHD

Signage/Professional Display|500 Nits Brightness |50000:1 Contrast

Ratio|Operation: 24x7|1xVGA;

1xDP, 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal), RJ45, RJ12, RS232,

Optical SPDIF |1xHDMI 2.0, 1xDP Out, Supports Daisy Chain| Speaker 2x12 W |

Open Content Management Support, Scheduler, USB Autoplay, AutoLaunch,

HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover, Panel Lock, OSD Rotation,

NoSignalPowerOff, Screen Saver, Pixel shift, Scheduler, Videowall support,

Remote control via LAN, Realtime Clock, Joystick, Rocker Switch| Optional :

OPS compatibility |Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of 65 inch UHD

Signage/Professional Display|400 Nits Brightness |50000:1 Contrast Ratio |

Operation: 24x7|1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal),

RJ45, RJ12, RS232, Optical SPDIF|1xHDMI 2.0 out, Supports Daisy Chain

|Speaker 2x10 W|30-degrees Tilting Installation | Open Content Management

3 65" inch Display Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-Wakeup, Nos. 4 ₹ 145,500.00 ₹ 582,000.00

Auto-switch on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen

Saver, Pixel shift,Scheduler, Videowall support, Remote control via LAN,

Realtime Clock, Joystick, Rocker Switch| Optional : SDM or OPS compatibility,

Embedded IR, IR extender option | Optional: Overlay Touch Kit

Compatibility|Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of 55 inch UHD

Signage/Professional Display|400 Nits Brightness |50000:1 Contrast Ratio |

Operation: 24x7|1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0 (Internal),

RJ45, RJ12, RS232, Optical SPDIF|1xHDMI 2.0 out, Supports Daisy Chain

|Speaker 2x10 W|30-degrees Tilting Installation | Open Content Management

4 55" inch Display Support, Scheduler, USB-Autoplay, AutoLaunch, HDMI-CEC, HDMI-Wakeup, Nos. 1 ₹ 105,000.00 ₹ 105,000.00

Auto-switch on Failover, Panel Lock, OSD Rotation, NoSignalPowerOff, Screen

Saver, Pixel shift,Scheduler, Videowall support, Remote control via LAN,

Realtime Clock, Joystick, Rocker Switch| Optional : SDM or OPS compatibility,

Embedded IR, IR extender option | Optional: Overlay Touch Kit

Compatibility|Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of Ceiling microphone with

automatic dynamic Beamforming technology, The beam will automatically

detect the position of the person speaking and will follow the person around

the room at all times. It should have 2 x Dante digital audio (Redundancy),

Analog audio out (Phoenix 3-pin), and Ethernet for Control and PoE

connectivity ports. The coverage of the ceiling microphone should be min 800

square feet or more. It should have a true voice lift feature to increase audio

5 intelligibility above the ambient noise floor. It should support IT industry Nos. 4 ₹ 689,570.00 ₹ 2,758,280.00

standards like IEEE 802.1x. It can be controlled through software that can

control and monitor the microphone in any network. It should have min 100 dB

SPL, 5ms latency, and min 90dBA or higher dynamic range. High-precision

audio settings for maximum control, setting to exclude (min 5) and prioritize

the areas of the room. It should certified from Microsoft Teams and Zoom

Video conferencing applications. It should have UL 62368 certification

(including UL 2043 testing and compliance) and safety certifications.

Supply, Installation, testing and commissioning of Full Digital Array Type, IR IN

Chip for Digital Conference Technology, chairmanUnit, 17 Built-in 9.7mm gold-

Table Top Array plated capacitive pick up head mic capsules, Should build in automatic gain

chariman function, Should have All aluminum alloy body, embedded "Vhs hardness level

microphone 8 touch glass panel Waterproof and dust & water-proof function, should have

(Wired) 3.5mm headphone interface, Power Consumption 2W), Pick up distance 60-

100CM, frequency responsee 30-20Khz etc complete required as iper access

Supply, Installation, testing and commissioning of Full Digital Array Type, IR IN

Chip for Digital Conference Technology, Delegate Unit, 17 Built-in 9.7mm gold-

Table Top Array plated capacitive pick up head mic capsules, Should build in automatic gain

Delegate function, Should have All aluminum alloy body, embedded "Vhs hardness level