PROVIDING EXTENSION AND EXISTING OF ANNATHANKKOODAM

Amount

Providing Extension and Renovation of Annathanakkoodam in Arulmigu Bannari Mariamman temple, Bannari,sathyamangalam taluk, Erode district.under HR&CE announcement no.90 in the year 2024-2025

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5;10 (One Cement, Five crushed stone sand and ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification (For Foundation)

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & basement up to GL

Ground floor

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For Plinth Beam

Square Column

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Random Rubble Masonry in CM 1:5 ( one cement and five sand ) using hard broken rough stones and bond stones in each layers with simultaneous pointing including cost and conveyance of all materials and labour charges etc., complete

Brick work in Cement Mortar 1:5 using best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specification.

Foundation and Basement

Ground floor ( Cement mortar 1 :6 )

First Floor

Brick partition walls of 11.50cm thickness using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Supplying and filling in foundation, basement, etc with GRAVEL in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with M.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification (For Flooring)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three plastering sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and five plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Dadooing walls with best approved quality, white / colour glazed tiles of 300x450x8mm set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Flooring with self designed colour ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with Snow white marble slab (Adanga) 18mm to 20mm thick and above free from all defects in all floors over a base layer of CM 1:3, 20mm thick. The marble slab shall be laid over the cement mortar by applying white cement slurry in between base mortar and marble slab and pointed with white cement neatly including polishing with polishing stone and oxalic acid etc. so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The marble slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing granite slab noshing (Double nosing). The cost is inclusive of all labour charges, hire charges for tools anf tackles etc., complete complying with standard specification.

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three crushed stone sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Providing granolithic floor finish of 40mm thickness with plain cement concrete 1:2:4 (One cement, two M.sand and four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying, fabricating & fixing of MS grill using 35x35x6mm MS angle as outter frame, cliet and 12mm square rods as grill members. The cost is inclusive of all materials and labour charges but excluding of priming coat etc., complete complying with standard specifications. The design of grill should got approved with executive engineer before use on work.

Supplying and fixing MS steel truss by using 65mm dia nominal bore MS pipe of wall thickness 3.6mm for post, 80x40x3.20mm rectangular tube for truss, 40x40x3.20mm square tube for purlins. The cost is including of all maerials and labour charges but excluding of priming coat etc., complete complying with standard specification

Manufacturing, supplying and fixing of steel doors with the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 35x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel in the shutter and welded intact for 1/3 bottom portion of the shutter. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat sandwitching the CR sheet in between. Additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 20kg/sq.m and 6 Nos hinges for double leaves shutter to be provided 6nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door. Tower bolts 2nos. one at top and the other at the bottom arte provided one aldrop is provided at on appropriate place in the door. A Tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all meterials, labour charges, taxes, transportation to site of work, loading, unloading and all other incidental charges but excluding of priming coat etc., complete.

Supplying fabricating and fixing MS weldmesh panels using 35x35x6mm 'L' angle for outter frames and 25x6mm flats for stiffener and weld mesh of size 7.5 x 2.5cm. 10g. The cost is including of all materials and labour charges but excluding of priming coat etc., complete.

Supplying and fixing colour coated galvalume sheet of size 0.47mm tk. The cost is including of all material and labour charges etc., complete

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (UPVC) sections. Profiles: The profiles should be tee chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting one coat of old plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with one coat of best approved first quality and colour of synthetic enamel paint in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

MODERN KITCHEN EQUIPMENTS

STEAM GENERATOR - LPG It is operated by the use of fuel like firewood diesel & LPG. Boiler outer shell 6mm MS Plate. Inner shelled & kid ring is made out of 14 SWG 304 grade stainless steel sheet. It has Only Provisions for fitted with accessories viz., safety valve, pressure gauge and gauge glass set to knowing the water level in the boiler. Drainage valve is fitted in the boiler water inlets also provided. Bye pass gate valve is provided to outlet the steam in case of emergency. No.3 Size : OD 28” x Ht 48” Steam Out Put – 65 Kg/Hr Water Capacity – 325 Liters

35 KG MULTI RICE VESSEL - SINGLE JACKETED It is fabricated by steel AISI 304 GRADE 16 SWG 304 grade stainless steel Sheet. The vessel bottom side is fabricated with perforated and welled sheet. Gate valve is provided to drain out the water from the bottom of the vessel. By using the tilting handle, the vessel can be easily tilted and transfer the cooked food items to other utensils seated in SS Button Rod. Inc of Fitting Materials SS U Clamp & Nut, Bootan Nut, SS Connection Pipe, Hanlde Rod & Nut, 1/2" Dummy & Stopper Pin. Dimension: OD 23” X 23” Ht

100L SAMBAR VESSEL- DOUBLE JACKETED It is fabricated 14 SWG Stainless Steel AISI304 GRADESHEET.The vessel is made out of fully double jacketed & it has only provisions for accessories including ½”safety valve, ¾” automatic steam trap valve to remove the condensed water in between the vessel.In this system the steam does not mix with the inner container.So the quantity of the liquid in the inner container willbe same as we quoted earlier. The vessel can be easily tilted and transfer the cooked food items to other utensils. Dimension:17"OD x 17”Ht

50L DHAL VESSEL- DOUBLE JACKETED It is fabricated 14SWG Stainless Steel AISI304 GRADE SHEET.The vessel is made out of fully double jacketed & it has only provisions for accessories including ½”safety valve, ¾” automatic steam trap valve to remove the condensed water in between the vessel.In this system the steam does not mix with the inner container.So the quantity of the liquid in the inner container willbe same as we quoted earlier. The vessel can be easily tilted and transfer the cooked food items to other utensils. Dimension:16" OD x 16”Ht

S.SLEG-BUSH TYPE It ismade out of Heavy Guage Stainless Steel Tubular Stand for mounting 4 Nos. Vessel

STEAMLINE FITTING MATERIALS FOR BOILER & VESSELS,GI PIPE 3/4" & 1" PIPE

INSTALLATION CHARGES

VEGETABLE CUTTER WITH 5 BLADES- STANDARD MODEL It is Made out of Aluminium Casting Head with SS Clading Capacity:150Kg/Hr Motor:1HP Single Phase

SS TILTING GRINDER 05L Motor: Single Phase & 0.5 HP Motor

SS TILTING GRINDER 10L Motor:Single Phase & 1HP Motor

POTRACK-4TIER Leg 1 1/2" Square Pipe. Frame & Support 1 1/2" x 3/4", 3/4" Square Pipe Dimension: 72"x 24 "x 66"Ht

VEGETABLE RACK -3 TIER Frame and Leg:1½”and 3/4" 304 Grade SS Square tube with adjustable Boot Shelves:Tape rModel with plastic container 15 Nos Provided Dimension:60" x 20" x 66"Ht

FOOD SERVICE TROLLEY-1 HOLES WITH LID It is made out of SS304 Grade 16 SWG SSS heet Fabricated Round Container:1No, Dimension:20"OD x 14"Ht 6"OD Wheel attached Attached with Handle For Rice Dimension: 24"x 24" x 30"Ht

FOOD SERVICE TROLLEY-2 HOLES WITH LID FOR SAMBAR & RASAM It is made out of SS 304 Grade 16 SWG SS Sheet Fabricated Round Container: 2 Nos, Container Size : 14" OD x 12" Ht 6" OD Wheel attached Attached with 2 Side Handle For Sambar & Rasam Dimension: 36" x 20" x 30" Ht

WASTE LEAF TROLLEY It is made out of SS 304 Grade 16 SWG SS Sheet Fabricated 4" OD Wheel attached Attached with one Side Handle Dimension: 31" x 24" x 21" Ht

LPG GAS LINE WORK5 MANI FOLD MS 1/2" Gasline Pipe , 1/2" MS Bend, 1/2" MS Elbow, Gas Line Union, 3/8 MS BUSH, Clamp, 1/2" GAS Line Dummy -1, Red Paint- 1/2L, Wood- 1 Pack, 1/2" Ball Valve -4 , Wooden Screw- 1 Packet,Rod- 1 Packet, 1/2" Hex Nipple, 1/2" Tee,4" Reg,2" Reg,Meter,Adaptor,NC Valve, Flexible Hose, Caller & Other Unit Fitting Materials. Inclusive of Labour Charges

PLATFORM TROLLEY It is made out of 16 SWG 304 Grade SS Sheet. 1 1/2 x 1/4 'L' Angle frame, with 6" OD Wheel Dimension: 48" x 30" x 8" Ht

COMMERCIAL MIXIE- HEAVY DUTY 2KG Motor: 3 HP, 3 Phase Full SS Covering- Tilting Type

WORK TABLE- 2 TIER Top:16 SWG 304 Grade SS Sheet Bottom: 18 SWG 304 Grade SS Leg: 16 SWG 1½” SS Square Tube With Adjustable Nylon Boot Dimension: 44” x 22” x33” Ht + 6" Splash

TRANSPORT CHARGES

SS SUCTION HOOD Specifications: Made out of 304 Grade N4 Finish 1 MM SWG SS Sheetwith removable SS Filter. Designed and Fabricated for easy Cleaning 304 Grade Dimension (BxH): 36" x 20" Length: 8 Feet

GI DUCT Specifications: Made out of 24 SWG GI Sheet Dimension(BxH):16"x12" Length: 25 Feet

GI BEND GI Bend for GI Running Pipe Set Specifications: Made out of 24 SWG GI Sheet Bend: 2 Nos

BLOWER WITH MOTOR MS Blower attached with Motor for Suction Specifications: With Dynamic Balanced Impeller with Motor Motor: 2HP 3 Phase Motor Capacity: 2HP

MS STAND & FITTING MS Stand for Blower & Fitting Materials for SS Hood, GI Pipe Specifications: Standard

EXHAUST SYSTEM INSTALLATION CHARGES

PROVISION FOR INTERNAL AND EXTERNAL ELECTRICAL ARRANGEMENTS

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End (Data A)

Supply and fixing of 4' 20W LED battern on wall or ceiling with TW round blocks with copper leads from fittings to terminals with electrical connections complete. (Data B)

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod on the existing fan clamp (SD 589)

Supply and fixing of 375 mm (15") sweep (Heavy duty) AC Exhaust fan complete without provision. (Data C)

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep (light duty) AC exhaust fan (SD 121)

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting . (SD 535)

Supply and fixing of 2 nos. 6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End (Set plug) (SD 466)

Supply and fixing of 1 no. 6/16A two module socket, 1 no. 16A one module switch on suitable module surface mounting Box (Plastic) with module cover plate (plastic) on wall with connections. Higher End (SD 484)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (SD 140)

Supply and fixing of 32A TP plug and socket in sheet enclosure with 32A TP MCB in flush with wall with earth connection (Data D)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 613)

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming, 3 nos. 32A TP MCB and 9 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End (Data E)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)

Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 61)

Supply and run of 4 of 6 sq.mm. (86 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 63)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 233)

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD 458)

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls for Brick / stone masonry in Cement mortar walls

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls for Dismanling Reinforced Cement Concrete

Dismantling, clearing away and carefully stacking materials useful for re-use for any thickness of walls for Removing Doors and Windows including removable offrames,hinges and fastenings

GST Amount for providing Service to Government Contract Works for the above works at 18%(9%+9%). {GST Amount is the Total GST Amount for overall quoted amount}

GURUSAMY CHANDRASEKARAN (BID ID -1174945)