Repair/maint to floor, plastering, tiling, roofing, AC sheet with false ceiling, roof treatment, joinery and certain other connected B/R work at OTM Accn and MD Accn at EME Line Fort Cantt Allahabad.

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracke framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to IS-1161: 1979, grade St-240, fix to section as in welding or screw, complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Stainless steel drapery rod, powder coated inner dia 30mm, for door and windows, fancy type including curtain rings, brackets, fancy type funnial and fixed to wall, complete all as specified and directed.

Dismantling framed hardwood/ soft wood timber scantlings 40 sq. cm and over in section, including removing bolt, nut etc in any position, complete all as specified and directed.

Second class hard wood timber scantling clean swan fixed as girder, lintels, wall plates, joist, purlin rafters, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork with sub class 'B' bricks (old size), straight or curved on plan exceeding 6metre mean radius, built in CM 1:6, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water including removing of all rubbish off from the site, complete all as specified and directed.

Rendering 15mm thick in CM 1:4, mixed with water proofing compound @ 2% weight of cement, on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved colour over a coat of 1mm thick wall care putty, complete all as specifed and directed.

Rendering 10mm thick in CM 1:6 on brick work or concrete surfaces of walls, finishing the surface even and fair, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash, complete all as specifed and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic emulsion paint, complete all as specifed and directed.

Rendering 5mm thick in CM 1:3 on concrete surfaces of ceilings, finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceilings and applying two coats of white wash, complete all as specifed and directed.

Complete removal of old decorated painted surfaces of wall including cornices, pilastered etc, by brooming down or steel wire brushing scrapping down smoke soot moulds , moss and efflorescent salts and trading oil and greasy sports and applying two coats of acrylic emulsion paint (approved clour/shade) on wall surface including wasing of floor, cleaning of glass, joinery, electrical fittings etc of drops & splash complete all as specified and directed.

Complete removal of old decorated painted surfaces of wall including cornices, pilastered etc, by brooming down or steel wire brushing scrapping down smoke soot moulds , moss and efflorescent salts and trading oil and greasy sports and applying two coats of cement base paint (approved clour/shade) on wall surface, complete all as specified and directed.

Dismantling Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) laid and bedded pointed in cement mortar, complete all as specified and directed.

Demolition of mud/lime concrete in roofs, any thickness, including plastering, old water proofing membrane and leeping including brick/brick tiles (whether full thickness removed or only a part thereof) and removing the rubbish from site for distance not exc 50m, complete all as specified & directed.

Providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3 kg per sq.m comprising of the following and testing of following: (a) 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:3 mixed with water proofing compound @ 3% by weight of cement, finished surface even and smooth without using extra cement. (b) One coat of Bitumen primer confirming to IS-3384-1965 @ 0.3 ltr per sqm. (c) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (d) Providing APP modified polymeric water proofing membrane having weight not less than 3 kg per sq.m with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length. (e) Again Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (f) Spread coarse sand @0.5 kg/sqm over entire bitumen surafce. Note: Water proofing compound to be measured and paid separately.

Plain cement concrete 1:2:4 type B-0 (12.50mm graded stone aggregate), as in levelling course, benching etc., and finished the surface even and fair, complete all as specified and directed.

Plain Cement concrete 1:2:4, type B-0 (12.5 mm crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges using water proofing compound, complete all as specified and directed. NOTE:- Water proofing compound shall be paid separately under respective item of this Schedule.

Bricks, sub class "A", laid flat on roofs, old size bricks bedded and jointed in CM 1:6 and pointed flush in CM 1:3, bricks bedded on 25mm thick sand layer, complete all as specified and directed.

Bricks, sub class "A", laid flat on roofs, old size bricks bedded and jointed in CM 1:6 and pointed flush in CM 1:3, bricks bedded on 25mm thick sand layer, complete all as specified and directed. [Except bricks]

Dismantling of AC corrugated or semi corrugated sheet including AC ridges as in roof or wall covering, complete all as specified and directed..

Asbestos cement corrugated or semi-corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed.

Asbestos cement corrugated or semi-corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed. [Expect sheet]

Asbestos cement two piece adjustable plain wing ridge, 6mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, including taking down existing unserviceable ridge, complete all as specified and directed.

Fibre glass reinforced translucent corrugated sheeting 2mm thick, with two corrugations side lap fixed with coach screw and washer in roof, wall etc, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Galvanised, corrugated mild steel sheeting, 0.63mm thick, with two corrugations side lap, fixed with ‘L’ type or ‘J’ type or cranked hook bolts in lieu of screws and washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and directed.

Galvanised, plain mild steel sheeting, 0.63mm thick, in ridges, hips, valley gutters, drip and straight flshings (length and girth as fixed), with grade of zinc coating 275, complete all as specified and directed.

Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa, as in roof covering / cladding to wall fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as speified and directed .

Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa, as in roof covering / cladding to wall fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as speified and directed .

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 sq.m but not exceeding 4.0 sq.m each and removing from site, complete all as specified and directed..

Pressed steel frames for doors of size 165 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. Note: The quoted rate shall be deemed to include one shop coat of primer.

Pressed steel frames for doors of size 105 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. Note: The quoted rate shall be deemed to include one shop coat of primer.

Flush shutters 35 mm thick, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured separately.

Steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, inlcuding two coats of synthetic enamel paint over a coat of red oxide primer after preparation of the new steel surface, fixed in repair, complete all as specified and directed. Note: Red oxide primer shall be already cattered by the factory.

Steel windows factory made with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded, inlcuding two coats of synthetic enamel paint over a coat of red oxide primer after preparation of the new steel surface, fixed in repair, complete all as specified and directed. Note: Red oxide primer shall be already cattered by the factory.

Steel ventilators, fixed type, with glazing bars guaged bar, fixed in repair, complete all as specified and directed.

Plain solid straight chowhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint of 2nd class hard wood (sal), complete all as specified and directed.

Block board 18/19 mm thick, interior grade, commercial type, fixed with screws to timber frame work, fixed in repair, complete all as specified and directed.

Prelaminated particle board, 18/19 mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, fixed in repair, complete all as specified and directed.

First class hardwood wooden Beads, 19mm width, straight (any size) for glazed or gauzed joinery, partical boards, renewed, including mitres etc. and removing old beads to store, complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open), fixed in repair, complete all as specified and directed.

Kitchen sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35mm x 35mm x 5mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, in repair, complete all as specified and directed.

Stainless steel plate rack (utensil rack) of size (600mmx750mm) and depth 300 mm made with 0.63 mm thick stainless steel sheet fixed with brass screw including necessary fittings, nut/bolts , washer etc., fixed in repair, complete all as specified and directed. Note: Sample of stainless steel plate rack shall be as approved by Accepting Officer.

Hasp and staple 100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws, complete all as specified and directed.

Framed work as in grills, grating etc with ends of bars shouldered and riveted, or forged in to spike frame guard bars, iron door hold fast etc confirming to Fe-410-0 or 310-0, complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

Plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate), 75mm thick as in plinth protection, finsihed even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metre and at every change of direction and filling the same with and including provision of bitumen and sand mixture at 1:3 proportion, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 50mm thick, as in flooring, laid in alternate bays / panels, including finishing the surface fair and even, complete all as specified and directed.

Wearproof topping as specified (incorporating an approved metallic floor hardner in ratio 1:4), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner), 20mm thick, complete all as specified and directed.

Supply only metallic hardner, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Non - skid Ceramic, jointless coloured tiles 7 to 8 mm thick, size of each tile shall be 300mm x 300mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Non - skid Ceramic, jointless coloured tiles 7 to 8 mm thick, size of each tile shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 350mm x 250mm x 7mm / 450 x 300 x 7 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:4, complete all as specified and directed.

Vitrified homogenous tiles (light shade) 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm each (minimum size of tile 600mm x 600mm), in floors. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Vitrified homogenous tiles (light shade) 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm each (minimum size of tile 600mm x 600mm), in vertical surfaces such as skirting, dados, riser to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10mm thick bedding in CM 1:4, complete all as specified and directed.

Non skid jointfree ceramic coloured tiles 400mm x400mm x 7 to 8 mm thick, in skirting, dados, risers to steps, etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4), complete.all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded in any mortar, complete all as specified and directed.

Granite, 18-20mm thick, (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc, complete all as specified and directed.

Machine cut mirror polished Kota stone slab 18-20mm thick, as in landing, stpes, flooring over and including 20 mm thick screed bed in cement mortar 1:6, laid and jointed in grey cement slurry mixed with pigment to match slab including rubbing and polishing mirror finish, complete all as specified and directed.

Machine cut mirror polished kota stone 18 to 20 mm thick over 10 mm thick bedding layer CM (1:4) in riser of steps, skirting, pillar etc laid and jointed in grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5sq.m each with shutters (without taking off shutters from the frames) including removing from site, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long, complete all as specified and directed.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, 100mm long, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised, 125mm long, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250mm long, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame (with and including punching or drilling out old glazing pins/spring clips and providing and fixing new ones) or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

Sheet glass, 3mm thick, ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Figured glass, 4mm thick, pin headed type and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specifed and direcetd.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repair, complete all as specifed and direcetd.

Preparation of new wooden surfaces exc 10 cm width or girth with sand or emery paper & applying two coats of synthetic enamel paint over a coat of pink primer , complete all as specified and directed.

Providing and fixing E-board Make: Everest, Design "Lake and Hill" of size 605mm x 605mm x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24mm x 32mm x 300mm and secured at 1200mm maximum centres securely fixed to structural soffits with hangers of 2mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200mm x 1600 mm modules cross tee longer than 600mm to be supported independently. 600mm x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 mm x 19 mm and 300mm long of white colour all as per manufacturers instructions, fixed in reapir, complete all as specified and directed. Make of Frame work : Armstong or equivalent

Mild steel tubing of 25mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings decorative holder and CP brackets, socket and knobs (wall to wall or flush to wall) for securing to curtain rod, fixed in repair, complete all as specified and directed.

Tubular towel rail of brass chromium plated, 20mm dia, D type, 60 cm long between flanges, fixed in repair, complete all as specified and directed.

Two way angle valve, cast copper alloy chromium plated, screwed down, high pressure, with crutch or butterfly handle, 15mm bore, screwed for iron pipe or for unions, fixed in repair, complete all as specified and directed.

Bib taps (fancy type), cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle, jointing with and including provision of 32mm dia 600mm long flush pipe and connections to pipes and fixing of chain and pull, or lever, if any, fixed in repairs, complete all as specified and directed.

PVC connection 15mm size with brass nuts on both ends of length 450mm, fixed in repair, complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including provision of cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, 'P' or 'S' trap 100mm bore of pipe, fixed in repair, complete all as specified and directed.

Vitreous China wash down water closet pan (pedestal pattern) , white (excluding flushing cistern and flushing pipe), white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, PVC (SWR) 'P' or 'S' trap and connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and directed. NOTE:- Plastic seat cover shall be measured as Supply only under respective item of this Schedule.

Supply only plastic seat cover for water closet, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Vitreous China wash hand basin white flat back of size 550 mm x 400mm fixed on cantilever brackets of mild steel angle 35mm x 35mm x 5mm, 32mm dia brass waste coupling, 32mm dia PVC waste pipe rigid quality and PVC connections 15mm bore 450mm long of PTMT, including fixing of taps, fixed in repairs, complete all as specified and directed. Note: Pillar tap/ mixture shall be measured and paid separately as supply only item.

Supply only pillar taps, fancy type, cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'HOT' or 'COLD' letter with long screwed shank and fly nuts, screwed for iron pipe 15mm bore pipe, complete all as specified and directed.

Waste pipe 32mm dia of polyethylene, flexible for wash hand basin or urinals, complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, , including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, , including cleaning for refixing or removal to store, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed.

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), in repair, complete all as specified and directed.

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including tank nipple etc, in repair, complete all as specified and directed.

Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, fixed in repair, complete all as specified and directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair, complete all as specified and directed.

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber gasket cup washing, fixed on walls, in repair, complete all as specified and directed..

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in trenches or in floors, in repair, complete all as specified and directed..

PVC (SWR) bends, fixed to pipes in walls making good with CM 1:4 or PCC 1:2:4, fixed in repairs, complete all as specified and directed.

PVC (SWR) bends with oval access door, ISI marked of any radius of 75 mm bore pipes jointed with rubber solvent, fixed in repairs, complete all as specified and directed.

CP grating 100mm dia, fixed with coloured cement joint to match the existing surface of tile, in repair, complete all as specified and directed.

M/S SHRINATH CONTRACTION

M/S SANJAY CONSTRUCTIONS

M/S A P CONSTRUCTION

Airways Enterprises

M/S ATUL CONSTRUCTION

M/S Akhilesh Enterprises

ms shanti sons

SK ENTERPRISES

AMARDEEP ENTERPRISES

shirdi sai builders

creative construction co.