Special repair to Bldg No T-243 (Z Coy CQMH stores) and Md Accn bldg No P14 at SUri Enclave and Guards at Mil Stn Beas udner GE Kapurthala

Amount

Demolition of PCC in Ground floors/PCC Path/Plinth Protection and paving not exceeding 15cm thickness (below or above ground level) etc, complete all as specified and directed by Engr-in-Charge.

Demolition cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed by Engr-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar, complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames), complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames with shutters exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames), complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (anythickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engr-in-Charge.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, complete all as specified and directed by Engr-in-Charge.

Demloition of Mud in roof , any thickness , including plastering and leeping (meather full thickness removed or a part thereof, complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up drain pipes 100 mm dia (salt glazed ware, AC or rienforced conc) set in cement Mortar, complete all as specified and directed by Engr-in-Charge.

Dismantling of 100 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed by Engr-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings including ridges, complete all as specified and directed by Engr-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thicknness, including cover fillets, complete all as specified and directed by Engr-in-Charge.

Dismantling taking down framed trusses of span not exceeding 10m, complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engr-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed by Engr-in-Charge.

All as per item No 18 above but except bricks etc, complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

M&L for 5mm thick Rendering in CM 1:3 on brick work or concrete surfaces on ceiling finished even and smooth without using extra cement etc complete all as specified and directed by Engr-in-Charge.

M&L for preparation of Newly plastered surfaces and applying three coats of White Wash on ceiling etc, complete all as specified and directed by Engr-in-Charge.

All as per item No. 23 above but over old surfaces of ceiling, including removal of existing treatment, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over and including a coat of chalk whiting/priming on plastered surfaces of walls, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces and distempering walls with two coats of distemper oil emulsion, white or tinted over and including 1mm thick wall care putty including primer, complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of exting treatment and applying two coats of oil emulsion distemper white or tinted over and including 1mm thick wall care putty including primer, complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment and applying two coats of Apex over and including priming coat, complete all as specified and directed by Engr-in-Charge.

M&L preparation of Newly plastered surfaces andapplying two coats of Apex over and including priming coat, ccomplete all as specified and directed by Engr-in-Charge.

Erection and fixing only steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed by Engr-in-Charge.

Erection and fixing only steel tubular work as in purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed by Engr-in-Charge.

S&F Roof truss/Framed works as in purlins, crane grantries, rails and fastening and heavy brackets framing Beam (of tee,angle, pipes of flat section , base plates etc) incluidng distence pieces, complete all as specified and directed by Engr-in-Charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note:- Glass and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed by Engr-in-Charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note:- Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed by Engr-in-Charge.

S&F Steel Ventilator 1.25mm thick Box Type fixed type prepared for fixing of gauzed and glass ( primer coated) ERW hollow P section of size 60mm x 25mm including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each vent ) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per vent (b) Handles of Z Sec 20mm x 100mm long (c) Stay (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note:- Wire mesh/glass pane and painting shall be measured and paid separately under appropriate item etc, complete all as specified and directed by Engr-in-Charge.

M&L for framed work as in doors or gates and chowkhats of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165), complete all as specified and directed by Engr-in-Charge.

S&F primer coated pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, lugs, hinges etc, complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engineer-In-Charge.

S&F 2nd class HW 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc, sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane, complete all as specified and directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples, wodden beads to steel windows/wooden doors, complete all as specified and directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples, wodden beads to steel windows/wodden doors as in repairs, complete all as specified and directed by Engr-in-Charge.

S&F solid PVC frame as in door, cupboard etc of size 50mm x47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube and edges will be painted to match with printed sheets, suppyling & fixing in opening as per specification & drawing, complete all as specified and directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; & 5mm thick x 15mm wide PVC sheet beading use inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree) used. Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by Engr-in-Charge.

S&F Aluminium anodised barrel tower bolts of extruded section of 125mm size etc, complete all as specified and directed by Engr-in-Charge.

S&F Aluminium handles, cast type anodised of size 125mm etc, complete all as specified and directed by Engr-in-Charge.

S&F stainless steel steel butt hinges cold rolled of size 100mm medium weight, complete all as specified and directed by Engr-in-Charge.

S&F Butt hinges 100mm size, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed by Engr-in-Charge.

S&F Mild steel pressed handles of size 150mm, oval type, stove enamelled black, complete all as specified and directed by Engr-in-Charge.

S&F Mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed, complete all as specified and directed by Engr-in-Charge.

S&F Mild steel sliding door bolts 250mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed by Engr-in-Charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new wood surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old painted wood based surface of any description over 10cm width of girth and applying one coat of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge.

S&F wind tie for roof including securing bolts: flat iron fillets including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe 410-0 or Fe 310-0 etc, complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium snap grid of size 605 x 605mm in frame work for false ceiling, complete all as specified and directed by Engr-in-Charge.

Providing and fixing Gypsum Board 8mm thick of size (600x600)mm in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engr-in-Charge (frame work for ceiling shall be measured and paid separately).

M&L for providing reinforced cement concrete cast in situ Type B-1, 1:2:4 ( 20 mm graded stone aggregate) as in lintels upto 1.5m clear span including necessary formwork, complete all as specified and directed by Engr-in-Charge. Note:- Reinforcement shall be measured and paid separately.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to, complete all as specified and directed by Engr-in-Charge.

All as per item No 65 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders, complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in chajjas, complete all as specified and directed by Engr-in-Charge.

Use and waste for formwork to chullah hoods, Chajjas, troughs and similar items including edges, complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in plinth protection finished even and smooth (without using extra cement), complete all as specified and directed by Engr-in-Charge.

M&L for joint free non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for coloured glazed ceramic tiles in vertical surface 450x350x7 mm thick laid over 10mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed by Engr-in-Charge.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over and including cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed by Engr-in-Charge.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed by Engr-in-Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including 20mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by Engr-in-Charge.

M&L for kota stone slab 20-25mm thick in riser of steps, skirtings, dado and pillar, laid over and including 15mm thick cement screed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, treating the surface with bees wax polish, complete all as specified and directed by Engr-in-Charge.

M&L for grinding and polishing the kota stone flooring/skirting with machine grinder and treating the surface with bees wax polish, complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 Type B1 ( 20 mm graded stone aggregate) as in bed blocks, coping, etc, complete all as specified and directed by Engr-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed by Engr-in-Charge.

M&L for hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type D2, 1:4:8(40mm graded aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Supplying and filling sand under floors or in foundations including watering and consolidation, complete all as specified and directed by Engr-in-Charge.

M&L for Machine pressed precast concrete interlocking paver block, 80mm thick, any shape and size, confirming to IS-15658-2006, M-40 Grade, with grey cement and no pigment complete all as specified and directed by Engr-in-Charge.

Removing excavated materials (soil) not exceeding 0.50m and depositing where directed of a level not exceeding 1.5m above the starting point, complete all as specified and directed by Engr-in-Charge.

M&L for 75mm thick cement concrete type C2 1:3:6 (40mm graded stone aggregate) in sub base, complete all as specified and directed by Engr-in-Charge.

Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors/path with grey cement and pigment to match, complete all as specified and directed by Engr-in-Charge.

S&F 20 mm dia curtain rod of mild steel with decorative finish , with fixing brackets complete all as specified and as directed (two brackets per opening of door and window and 08 Nos PVC rings), complete all as specified and directed by Engr-in-Charge.

M&L for roughening surfaces of old/concrete floor by backing sweeping clean and washing down with water etc, complete all as specified and directed by Engr-in-Charge.

M&L for 15mm thick screed bed or bedding layer of mortar in CM 1:4, using WPC, complete all as specified and directed by Engr-in-Charge.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application, over a coat of hot blown bitumen 85/25 @ 1.20 kg/Sqm, complete all as specified and directed by Engr-in-Charge.

M&L for PCC padding 1:2:4, type B-1(using 20 mm garded stone aggregate) of average thickness 75 mm to be provided in slope, complete all as specified and directed by Engr-in-Charge.

M&L for 40 mm thick brick tiles laid on cement mortar and joints grouted flush in CM 1:3 mixed with 5% of crude oil by weight of cement, complete all as specified and directed by Engr-in-Charge.

All as per item No. 92 but except tiles, complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exceeding 10 cm but not exceeding 20 cm girth, complete all as specified and directed by Engr-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed by Engr-in-Charge.

S&F in repair Stop valves, cast copper alloy, bore dia of pipe in 15mm, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for ironn pipe and fixed but fancy type, Chromium Plated with long shank and cup (concealed type) etc complete all as specified and directed by Engr-in-Charge.

M&L for chromium plated bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe and fixed to 15mm bore pipe fixed as in repairs including taking down old tap of any description, complete all as specified and directed by Engr-in-Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450mm etc, complete all as specified and directed by Engr-in-Charge.

S&F in repair gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe or union, 20mm bore dia of pipe, complete all as specified and directed by Engr-in-Charge.

S&F in repair Low Level Flushing System PVC valveless syphonic action type, 10 ltrs capacity including supply pipe & fixing brackets of M.S. angle of size (25mmx25mmx3mm), 30 cm long in PCC (1:2:4) type B-1, block of size (10cmx10cmx10cm) on walls etc, complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous China Wash Basin with full pedestal, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc complete all as specified and directed including 15 mm dia Pillar taps, cast copper alloy with capstan heads Chromium Plated, screwed down high pressure, with or without lettered with long screwed shanks and fly-nuts, screwed for iron pipe but fancy type and fixed etc, complete all as specified and directed by Engr-in-Charge.

S&F in repairs swivel shower of CP with shower arm 195mm long with bend of 45 degree 15mm dia, complete all as specified and directed by Engr-in-Charge.

S&F CP garting 100mm dia with waste hole of etc, complete all as specified and directed by Engr-in-Charge.

Taking up or down Steel Tubing bore of pipe in 15mm and connections, including cleaning for refixing or removal to store etc, complete all as specified and directed by Engr-in-Charge.

All as per item No. 105 above but of 20mm bore, complete all as specified and directed by Engr-in-Charge.

S&F Steel Tubes Medium Grade Bore of tube in 15mm galvanised with all fitting laid in trenches, walls, ceiling or laid in floors etc, complete all as specified and directed by Engr-in-Charge.

All as per item No. 107 above but of size of 20mm bore, complete all as specified and directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC Float valve also dismantling of existing tank and removing from site, complete all as specified and directed by Engr-in-Charge.

Disconnecting existing PVC water tanks, setting aside (or lowering if required) and cleaning and removing all scales and dust from PVC water tank manually and cleaning, scraping inner surfaces of tank by means of brush and then washing with clear water and cleaning of mouths of circulating pipes of capacity of tank exceeding 250 litre but not exceeding 500 litre and reconnecting and refixing in position, complete all as specified and directed by Engr-in-Charge.

S&F in repair angle valves, cast copper alloy, bore dia of pipe in 15mm, screwed down, high pressure, with crutch or but-terfly handle, screwed both ends for ironn pipe and fixed but fancy type, Chromium Plated with long shank and cup etc, complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:1.5:3) type A-0 (12.5 mm stone graded aggregate), complete all as specified and directed by Engr-in-Charge. Note:- All traps in sunken slabs to be enclosed with PCC 1:1.5:3, min 15cm all-round.

M&L for plasteing in CM (1:3) 15mm thick with WPC on walls as on sunken floor finished even and smooth using extra cement complete all as specified and directed by Engr-in-Charge. Note:- After doing the plaster testing be carried out by ponding (for 72 hrs) the sunken portion before further treatment to the sunken slab.any leakage/seepage obserbed shall be rectified before carrying out water proofing treatment.

M&L for for applying a tack coat of industrial bitumen 85/25at the rate of 1.2 kg/sqm including cleaning of surface, complete all as specified and directed by Engr-in-Charge.

Supply only Integral waterproofing compound, complete all as specified and directed by Engr-in-Charge.

S&F GI pipe 40mm dia medium grade and inserted at the end of lateral slope projecting atleast 15 cm beyond the outermost projected part of the building below the drain pipe, complete all as specified and directed by Engr-in-Charge.

M&L for applying evenly coat of hot blown bitumen 85/25 at the rate of 1.2kg/Sqm under and over APP membrane including cleaning of surfaces. over a coat of bitumen primer @ 0.40 lit per sqm and applying standard quality APP based polymeric membrane minimum weighing 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less then 150gms/Sqm) laid on primed surface by forced application, complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:5:10 type E-2 with brick coarse aggregate to be filled in sunken portion, complete all as specified and direced by Engineer-In-Charge. Note:- The sunken portion shall be filled with PCC 1:5:10 with brick aggregates after carrying out the required tests for pipes/joints/ waterproofing treatment.

S&F 110 mm bore PVC(SWR) pipes single sockets in any length with rubber ring joints fixed to walls including fixing with old clamps, complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC(SWR) pipes single sockets in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC(SWR) bend any radius, complete all as specified and directed by Engr-in-Charge.

S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal. Complete all as specified and directed by Engineer-In-Charge.

S&F PVC (SWR) floor trap of 110mm outlet dia, plain with grating including jointing with solvent cement. Complete all as specified and directed by Engineer-In-Charge.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) bends any radius, complete all as specified and directed by Engr-in-Charge.

Cutting holes into or through brick walls superfacial area n.exc. 150 sqcm bult in cement mortar or cement lime mortar and making good in c.m 1:3 or cement concrete 1:2:4 type B-1 including matching the surfaces with the existing surface finishes complete all as specified and directed by Engr-in-Charge.

M&L for angle, joist, channel or tee sections fixed independently,without connecting plats. Etc. (Fe-290 Gde-E-165), complete all as specified and directed by Engr-in-Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engr-in-Charge.

S&F for 18mm thick high grade PVC boards fixed with and including steel frame work fixed with screws, complete all as specified and directed by Engr-in-Charge.

S&F towel rail 600mm long of stainless steel fixed with and including Chromium plated brassscrews and or cleats, complete all as specified and directed by Engr-in-Charge.

M&L for dugging out average 10mm thick on disturbed chajja beam, slab portion and applying chicken wire mesh over disturbed portion fixed with drilling bolting etc.after anti corrosion treatment of steel bar and finaly finished with 10mm thick (1:3) cement plaster mixed with WPC @ 3%by the weight of cement all as specified and directed. Note: WPC shall be measured and paid separately, complete all as specified and directed by Engr-in-Charge.

M&L for preparation of affected concrete and steel surfaces as in ceiling of roof slab by cleaning with metallic wire brush scruplously and carrying out the the following operations stepwise. (i) Applying rust remover solution on steel bars by using cotton waste swab or by brush and leave the surface for atleast 15 to 30 minutes. Remove the loose rust particles by scrubbing with brush and wash the steel surface with water. (ii) Apply red oxide primer over cleaned steel surfaces. (iii) Apply epoxy bonding agent (adherent solution) over cleaned dust freed old concrete surfaces. (iv) Apply Polymer mortar with the help of trowel in single or multilayer as or when required during application and finishing the surface even and smooth. Note:- (a) The bars which are corroded badly has to be strengthen by placing new bars by means of welding with proper splice length and will be measured and paid separately under appropriate item. (b) The rate of item includes necessary formwork, shuttering, scaffolding staging etc.

M&L for running welding in repairs, thickness of metal exceeding 6mm but not exceeding 9mm, complete all as specified and directed by Engr-in-Charge.

Taking down carefully aluminium point wiring on casing caping/through conduit (light fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls/ceiling/ floors etc complete all as specified and as directed by Engr-in-Charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store, complete all as specified and as directed by Engr-in-Charge

M&L for point wiring for one light or one fan point controlled by one switch or with one switch and regulator with PVC unsheathed single core multistranded copper conductor (FRLS) cable of size 1.5 Sqmm (nominal area) in and including PVC conduit 20 mm bore by cutting chases in wall by cutter and making good the surface in cm 1:3 and to the original specification and cast iron /pressed steel concealed terminal boxes including providing 3mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated copper conductor (FRLS) cable of size 1.5 sqmm with green insulation as earth wire and connected to earth dolly, complete all as specified and as directed by Engr-in-Charge

All as per Srl item No 137 here in before but for 3 pin socket outlet 5 Amps on same board .

All as per Srl item No 137 above but for 3 pin socket out let 5 Amps on independent board

All as per Srl item No 137 above but one light point controlled by two way switches

All as per Srl item No 137 here in before but for 3 pin socket outlet 15 Amps on independent board with PVC unsheathed copper conductor cable of size 2.50 Sqmm including copper earth wire of size 1.50 Sqmm and connected to common earth dolly, complete all as specified and as directed by Engr-in-Charge. Note:- Switch/socket to be measured & paid for separately.

S&F in replacement sub main wiring with two single core FRLS insulated cable with copper conductor stranded and sheathed of size 6 Sq mm in and including PVC conduit including 1 x 6 Sq mm FRLS copper earth wire to common earth and connected to earth dolly, complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type 5 Amp single pole one way, complete all as specified and as directed by Engr-in-Charge.

S&F switch piano 5 Amp flush type single pole two way, complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type 15 Amp single pole one way, complete all as specified and as directed by Engr-in-Charge.

S&F socket outlet 5 pin 5 Amps flush type multipurpose, complete all as specified and as directed by Engr-in-Charge.

S&F socket outlet multipurpose 2 in one, 3 pin 5/15Amps flush type, complete all as specified and as directed by Engr-in-Charge.

S&F bell push flush type 5 Amp single pole one way, complete all as specified and as directed by Engr-in-Charge.

S&F ceiling rose surface bakelite 65 x 50mm three terminal, complete all as specified and as directed by Engr-in-Charge.

S&F fan regulator electronic step type and making connections, complete all as specified and as directed by Engr-in-Charge.

S&F call bell Ding dong single phase 240 volt AC, complete all as specified and as directed by Engr-in-Charge.

S&F Angular lamp holder insulated body with back plate suitable for batten fittings including 1 x 9 W LED Lamp Make- Havells LED ADORE 9 W B22 WW 3 STAR LAMP Cat No LHLDEUEEMC8R009 or equivalent complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable FTL fitting 36/40Watt and S & F surface mounting energy saving LED tube light fitting, 1x20W, 230V , high efficiency PMMA diffuser gives soft glare free light with LED tube rode 20 W (White), complete all as specified and as directed by Engr-in-Charge.

Fixing only ceiling fan 1200 mm sweep, 240 Volts and connecting up including provision of flexible copper conductor cable from ceiling rose / connector to fan and GI pipe/ steel rod, nuts, bolts, clamps etc as required at site, complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of ceiling fan 1200 mm sweep, 240 Volts Colour- Opal White Make- Crompton Model Cool Breez or equivalent in Bajaj/Havells/Orient, and connecting up including provision of flexible copper conductor cable from ceiling rose / connector to fan and GI pipe/ steel rod, nuts, bolts, clamps etc as required at site, complete all as specified and as directed by Engr-in-Charge.

S&F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver (metal body)Including necessary cutting of wall in sutiable dia for the fixing of exhaust fan and make it in good finish with plaster work complete all as specified and as directed by Engr-in-Charge.

S&F water heater storage type, electric,capacity 25 litres, complete all as specified and as directed by Engr-in-Charge.

S&F PVC connection cold water pipe 18" long, 15mm dia with brass jem nut and wahser, both side complete all as specified and as directed by Engr-in-Charge.

All as per ser item No 158 here in before but hot water pipe made of chromium plated brass flexible tubing, complete all as specified and as directed by Engr-in-Charge.

S&F stop cock brass of size 15 mm dia, complete all as specified and as directed by Engr-in-Charge.

S&F bib cock brass of size 15 mm dia, complete all as specified and as directed by Engr-in-Charge.

S&F MCB single pole 6 to 32 Amps 240 Volts, complete all as specified and as directed by Engr-in-Charge.

S&F MCB 40 Amp SPN 240 volt, complete, complete all as specified and as directed by Engr-in-Charge.

S&F sheet metal enclosures with double door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire and neutral link,SPN 12 ways, 240 volts, complete all as specified and as directed by Engr-in-Charge.

S&F TPN Vertical type Distribution Box (VTPN DB) in double door,IP -54, suitable for flush mounting and surface mounting with 250 A copper bus bar for each Ph ,two neutral bar, two Earthbar with provn for MCCB 100 A as Incomer (W/O MCCBs)and SP /TP as out going complete all as specified and as directed by Engr-in-Charge.

S&F MCCB 100 Amp 4P 415 volt, 36 KA complete, complete all as specified and as directed by Engr-in-Charge.

M&L of earthing complete with galvanized steel earth plate trode 60cm x 60cm x 6mm thick buried directly in ground vertically in a pit not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected to GI earth wire 4mm dia by means of bolts, nuts and washers (earth plate covered with charcoal dust and common salt in alternate layers) GI earth wire protected by galvanized steel pipe light grade of 15 mm dia upto switch board and connected to main switch board, including provision of 20mm dia GI tubing light grade watering pipe with funnel and wire mesh PCC earth pit (1:3:6) type C-1 covered with CI cover hinged with frame including excavation and earth work complete all as specified and as directed by Engr-in-Charge and shown in electrical plate No 5 of SSR Part I including testing on completion.

Disconnecting and taking out old u/s cable of service connection / sub main of any size and type from pole to DB's / Main switch complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for ltaking out old cable/laying of under ground cable/foundation of poles/stays including segregation of old serviceable bricks complete all as specified and as directed by Engr-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer complete all as specified and as directed by Engr-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L for brick protection using old size sub class 'B' bricks, laid flat dry but adjoining to each other laid lengh wise perpendicular to the axis of cable complete all as specified and as directed by Engr-in-Charge.

Supplying, filling in trenches spreading, leveling sand cushioning 8 cm below and 15 cm above the cable for under ground cable complete all as specified and as directed by Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core, complete all as specified and as directed by Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core, complete all as specified and as directed by Engr-in-Charge.

S&F LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed by Engr-in-Charge.

S&F LED bldg security light fitting 20 watt Powder coated pressure die cast aluminium compact LED security light including 1.5 mtr long 40 mm bore GI pipe mounting bracket made to shape for fixing on wall with 40 mm x 6 mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washers complete all as specified and as directed by Engr-in-Charge.

M&L for GI Pipe 'light grade' galvanized with all fitting laid in trenches/ on pole/road crossing of size 40mm, complete all as specified and as directed by Engr-in-Charge.

S&F vitreous chaina squatting pan (Orissa Pattern), size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and directed by Engr-in-Charge.

S&F wire netting of galvanized steel wire 1.40 mm dia fixed with tinned tacks of wire staples and size of mesh 25mm fixed with RCC/PCC/Brick surface all as specified and directed by Engr-in-Charge.

COSMO BUILDERS

SUNRISE CONSTRUCTION COMPANY