Provn of certain Special repair, Revenue and Minor works at Mil Stn Beas and Jandiala Guru under GE Kapurthala.

Amount

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings including ridges complete all as specified and directed by engr-in-charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by engr-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness below or above ground level including tiles, terrazzo/stones etc complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by engr-in-charge.

Taking down cement plaster or cement lime mortar any description on brick or stone wall, etc including racking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by engr-in-charge.

Taking down chowkat or frame with shutters exc 1.5 sqm but n.exc 4 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkat or frame with shutters n.exc 1.5 sqm each (without taking off shutters from the frame) complete all as specified and directed.

Dismantlling water tank of capacity exc 250 ltrs and not exc 500 ltrs and removing to store of any description.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store, bore of pipe 15mm complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store, bore of pipe 20mm complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

S&F rolled mild steel Fe 410-W (Gde-E-250) quality-A in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by engr-in-charge.

M&L for 75mm thick cement concrete type c-2, 1:3:6 (40mm graded stone aggregate) as in plinth protection finished even and smooth (w/o using extra cement) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sub floor finished even and rough to receive the topping layer (w/o using extra cement) complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per item No 19 above but except bricks

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6 on walls finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 on walls finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint on walls complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed by Engineer-in-charge.

M&L for joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick square/ rectangular) laid over 15mm thick screed bed in cement mortar 1:6, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by engr-in-charge.

M&L for Glazed ceramic coloured tiles in vertical surface 300x200x 7 mm thick laid over 10mm thick screed bed in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed by engr-in-charge.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in cement mortar 1:6 and pointed in white or colour cement to match complete all as specified and directed by engr-in-charge.

M&L for 50mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sub floor finished even and rough to receive the topping layer (w/o using extra cement) complete all as specified and directed.

Supply and fix mild steel framed work of angle or any other section confirming to Fe-410 Gde E-250 quality `A' as in door and door frame, threshold, holdfasts, gates etc of angle frame work etc including necessary welding etc complete all as specified and directed by Engineer-in-Charge.

S&F 2nd class HW 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engr-in-Charge.

S&F Extruded aluminium alloy handles, fabricated type, anodised 100mm size complete all as specified and directed by engr-in-charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm complete all as specified.

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by engr-in-charge.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by engr-in-charge.

M&L for preparation of new wood surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified including 20mm dia ball brass valve complete all as specified and directed by engr-in-charge.

S&F vitreous china squatting pan (Orissa pattern), size 580 x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding as in repairs complete all as specified and directed by engr-in-charge.

S&F Vitreous China Wash Basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or eracting stand & waste pipe, coupling etc as in repairs complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device with recessed bottom, jet spray, etc as in repairs complete all as specified and directed by engr-in-charge.

S&F Low Level Flushing System PVC valveless syphonic action type, 10 ltrs capacity including supply pipe & fixing brackets of M.S. angle of size (25mmx25mmx3mm), 30 cm long in PCC (1:2:4) type B-1, block of size (10cmx10cmx10cm) on walls, as in repairs etc complete all as specified and directed.

S&F 15mm dia Chromium plated bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe and fixed to 15mm bore pipe fixed as in repairs including taking down old tap of any description complete all as specified and directed.

Supply only 15mm dia Pillar taps, cast copper alloy with capstan heads Chromium Plated, screwed down high pressure, with or without lettered with long screwed shanks and fly-nuts, screwed for iron pipe but fancy type and fixed etc complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm etc complete all as specified and directed.

S&F 15 mm dia angle stop valve of PTMT any colour pressure screwed for iron pipe and fixed (minimum weight 15mm - 90 gms) as in repairs complete all as specified and directed.

S&F grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc complete all as specified and directed.

S&F grating doom 100mm dia with waste hole of PTMT (minimum weight 25 gms) etc complete all as specified and directed.

S&F grating square 150mm size of PTMT (minimum weight 100 gms) etc complete all as specified and directed.

S&F Steel Tubes Medium Grade Bore of tube in 15mm galavanised with all fitting laid in trenches, walls, ceiling or laid in floors etc complete all as specified and directed.

All as per item No 53 above but of size of 20mm bore

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), 15mm bore of pipe complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), 20mm bore of pipe complete all as specified and directed.

M & L for providing Reinforcement cement concrete cast in situ Type B-1, 1 : 2 :4 ( 20 mm graded stone aggregate) as in lintels upto 1.5m clear span including necessary formwork complete all as specified and directed by engr in charge.(Note : Reinforcement shall be measured and paid separately)

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by engr-in-charge.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal/sloping), fair finished surfaces concrete flat complete all as specified and directed by engr-in-charge.

S&F mild steel TMT bars 10mm dia and above, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with and including MS wire annealed not less than 0.9mm dia complete all as specified and directed.

All as per item No 60 above but 6mm to 8mm dia.

-ditto- all as per item No 60 above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders.

Cutting chases, pinning in, making good to facinngs where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc, and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M & L for PCC 1 : 2 :4 Type B1 ( 20 mm graded stone aggregate) as in bed blocks, coping, etc complete all as specified and directed by engr-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed by Engineer-in-charge.

S&F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union as in repairs complete.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to steel pipe or union, 20mm bore dia of pipe complete as in repairs.

S&F 15mm dia fancy type, chromium plated with long shank and cup (concealed type) stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repairs complete.

S&F steel ventilators, fixed type, with glazing bars including one shop coat of zinc chromate primer complete all as specified and directed by engr-in-charge (Note : Glass/wire mesh and painting shall be measured and paid separately under appropriate item).

Supply only 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by engr-in-charge.

Supply only Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed by engr-in-charge.

S&F PVC (SWR) P trap 110/110mm bore complete.

S&F 110mm bore PVC (SWR) WC connector with lip ring complete all as specified and directed by engr-in-charge.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by engr-in-charge.

S&F 75mm bore PVC (SWR) junction single tee equal or unequal complete all as specified and directed by engr-in-charge.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls as a vent pipe complete all as specified and directed by engr-in-charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by engr-in-charge.

S&F 75mm bore PVC (SWR) bend any radius complete all as specified and directed by engr-in-charge.

S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

M&L for PVC (SWR) floor trap, plain with grating 75mm diameter of outlet, setting and jointing with solvent cement complete.

M&L for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

Excavation in trenches in soft/ loose soil not exceeding 1.5 m wide n.exc 1.5m depth for fdn etc for shaft, wells, cesspits, man holes, pier holes etc. n.exc 10sqm on plan and n.exc 1.5m depth and getting out in soft/loose soil complete all as specified and directed by engineer-in-charge.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/ loose soil..

Surface excavtion not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and as directed by Engineer-in-Charge

Excavation in post holes(or similar holes ) each not exceeding 0.50 Cum, and getteing out, returning filing in and ramming earth with broken rubble mixed with earth around in layers not exceeding 25cm, watering etc and removing surplus soil not exceeding 50m and making good surface in loose/soft soil, complete all as specified and directed by Engineer-In-Charge.

Removing excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point.

M&L for cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

Providing cement concrete type C-1 1:3:6 (20mm graded stone aggregate) in pedestal, bed plates, etc complete all as specified and directed by engr-in-charge.

M & L for hardcore of gauge not exceeding 63 mm of broken stones or boulders, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed..

Supply and fixing tubular steel work in vertical posts, rafters, purlins, etc including special shaped washer and structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor's workshop, etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240.

S&F rolled sections(angle, pipe,tee, square pipe, plate etc) as in main and crissed beams , posts, hip and rafters etc, fixed with angle cleats or other connecting plates, rivets ,nut bolts etc, complete all as specified, conforming Fe 410W (Gde E-250) Quality B

M&L for granite (of any type) tiles 18-20mm thick machine cut, bedded over 15mm thick cement screed in cement mortar 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing types complete all as specified and directed by engr-in-charge.

Cutting holes into or through brick walls built in cement mortar or cement lime mortar, superficial area exc 400 sq cm but n.exc 0.10 sqm complete all as specified and directed by engr-in-charge.

M&L for 100mm thick PCC 1:2:4 type B-1 with 20mm graded stone aggregate as in flooring, finished even and fair (without using extra cement) including spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green laid in alternate bays complete all as specified and directed by engr-in-charge.

M&L for cement concrete type E2, 1:5:10 as in foundations, filling and mass concrete complete all as specified and directed.

M&L for 75mm thick cement conc type C2, 1:3:6 (40mm graded stone aggregate) as in sub base finished even and rough to receive the topping layer complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation complete all as specified and directed.

M&L for 80mm thick,machine pressed precast concrete interlocking paver block,coloured with grey cement and pigment any shape and size comforming to IS15658-2006,M-40 grade with sand cushioning complete all as specified and directed.

M&L for reinforced cement concrete M-25 Design Mix using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L for filling good earth including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each layer, complete all as specified and directed by Engineer-in-Charge.

Use and waste the formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc.; vertical or to batter, complete all as specified and as directed by Engineer-in-Charge.

M&L for reinforced cement concrete M-25 Design Mix using 20mm graded stone aggregate as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; including attatched pilasters and buttresses, complete all as specified and as directed by Engineer-in-Charge.

M&L for 5mm thick Rendering in CM 1:4 on brick work or concrete surfaces finished even and smooth etc complete all as specified and directed by Engineer-in-Charge.

M&L for Plain Cement Concrete Type C2, 1:3:6 (using 40 mm graded stone aggregates) as in foundations, filling & mass concrete etc complete all as specified and directed.

Extra for forming fair finished drain or channel inner girth 45cms in cement concrete, using extra cement including forms, moulds mi- tred/ stpped ends etc complete all as specified and directed.

M&L for RCC NP2 pipe 450mm dia bore and jointed complete with collars as in culvert complete all as specified and directed.

M&L for providing precast RCC 1:2:4 type B1 using 20mm graded stone agg as in cover slab for man holes and shelve of cup board set in CM 1:4 complete as directed.

M&Lfor cement concrete ( 1:3:6 type C2) bed to drain pipes of 450mm bore dia including packing under and completely surrounding pipes with concrete after they are laid and tested all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0(Using 12.5mm graded stone aggregate) as in damp proof courses to horizontal or vertical surfaces , Tye B-0 including necessary formwork laid over layer of Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m, complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick cement concrete type C-2, 1:3:6 as in Subbase of footpath, complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) as in flooring, finished even and smooth with using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion, complete all as specified and directed by Engineer-in-charge.

S & F mild steel screw bolts (machine made) with hexagonal or Square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, exceeding 5 cm but not exceeding 10 cm long, dia of shank 10 to 15 mm, complete all as specified and directed by Engineer-In-Charge.

S&F 30mm thick, 2nd class hardwood flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides supplied and fixed to chowkhats, complete all as specified and directed by Engineer - in - Charge.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by engr-in-charge.

S&F Mild steel sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by engr-in-charge.

S&F Mild steel barrel tower bolts 200mm long, stove enamelled black, with bright bolt and fixed complete all as specified and directed by engr-in-charge.

S&F Mild steel pressed handles of size 150mm, oval type, stove enamelled black complete all as specified and directed by engr-in-charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawings. Note : Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

M&L for machine pressed precast conctete interlocking paver block, 80mm thick, any shape and size confirming to IS 15658-2006, M-40 Grade, with grey cement and no pigment, complete all as specified and directed by Engineer-in-Charge. Make- Supertile

S&F anodised aluminium snap grid of size 605 x 605mm in frame work for false ceiling complete all as specified and directed by engr-in-charge.

Providing and fixing Gypsum Board 8mm thick of size (600x600)mm in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by engr-in-charge (frame work for ceiling shall be measured and paid separately).

S&F MS Pipes as in vertical posts , fixed with angle cleats or other connecting plates, rivets ,nut bolts etc, complete all as specified, conforming Fe 410W (Gde E-250) Quality B

M&L for coloured non skid jointless ceramic tiles of size 400mmx400mmx7mm thick, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match 15mm thick screed bed in CM 1:4, complete all as specified and directed by engr-in-charge.

Taking down carefully aluminium point wiring on casing caping/through conduit (light fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, box type tube light fittings, removing the materials from site except fittings etc which shall be reused in the work and making good the disturbed surfaces of walls/ceiling/ floors etc complete all as specified and as directed by Engineer-in-Charge

M & L for point wiring for one light or one fan point controlled by one switch or with one switch and regulator with PVC unsheathed single core multistranded copper conductor (FRLS) cable of size 1.5 Sqmm (nominal area) in and including PVC conduit 20 mm bore by cutting chases in wall by cutter and making good the surface in cm 1:3 and to the original specification and cast iron /pressed steel concealed terminal boxes including providing 3mm thick plastic laminated sheet cover (Hylem) including one run of PVC insulated copper conductor (FRLS) cable of size 1.5 sqmm with green insulation as earth wire and connected to earth dolly complete all as specified. (Switch/Socket outlet to be measured & paid for separately). Make of cable: Finolex/Anchor/Havell’s

All as per Srl item No132 here in before but for 3 pin socket outlet 5 Amps on same board .

All as per ser item 132 above but for 3 pin socket out let 5 Amps on independent board

All as per srl item No 132 here in before but for 3 pin socket outlet 15 Amps on independent board with PVC unsheathed copper conductor cable of size 2.50 Sqmm including copper earth wire of size 1.50 Sqmm and connected to common earth dolly complete all as specified. (Switch/socket to be measured & paid for separately)

Supply & fixing switch piano flush type 5 Amp single pole one way.

Supply & fixing switch piano flush type 15 Amp single pole one way.

Supply & fixing socket outlet 5 pin 5 Amps flush type multipurpose.

Supply & fixing socket outlet multipurpose 2 in one, 3 pin 5/15Amps flush type.

Taking down old unserviceable FTL fitting 36/40Watt and S & F surface mounting energy saving LED tube light fitting/ Batten with LED T8 Tubelight with PC body, 1x20W, 230V , Cat Part No of Batten DMLN1LT8-16 & Cat Part No LT8-20-865-2 for LED T8 Tube light Make- Crompton or equivalent complete with all accessories.

Supply and fixing MCB single pole 6 to 32 Amps 240 Volts, B Series Product Code CSMBS1B6 to CSMBS1B32 Make- C&S or equivalent in Havells/GE/ L &T/Legrand

Supply and fixing MCB single pole 32 Amps 240 Volts SPN , B Series Product Code CSMBS1B6N to CSMBS1B32N Make- C&S or equivalent in Havells/GE/L&T/Legrand)

Supply & fixing sheet metal enclosures with double door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire and neutral link, 8 ways, 240 volts. ( Make- Havells/Legrand)

Supply & fixing sheet metal enclosures DB Single Pole and Neutral 4 way with double door, detachable gland plates flush/ mounting for MCB’s fitted with bus bar, earth wire, 220 volts including taking down of existing DB at site all as specifed and directed.. Make-Havells/L&T/Indo Asian

Supply & fixing ceiling rose surface bakelite 65 x 50mm three terminal complete all as specified and as directed by Engineer-in-Charge. Make – Anchor/Leader/Bajaj

Supply & fixing Angular lamp holder insulated body with back plate suitable for batten fittings including 1 x 9 W LED Lamp Make- Havells LED ADORE 9 W B22 WW 3 STAR LAMP Cat No LHLDEUEEMC8R009 or equivalent all as specified and directed by Engr in Charge.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver including making of hole on wall for passing out air and provision of flexible three core copper conductor cable of 23/0.0076 up from ceiling rose to fan and grouting 04 Nos bolts in wall.

M & L of earthing complete with galvanized steel earth plate trode 60cm x 60cm x 6mm thick buried directly in ground vertically in a pit not less than 2.25 meter below ground level with top edge of earth plate at a depth not less than 1.5 meter below level connected to GI earth wire 4mm dia by means of bolts, nuts and washers (earth plate covered with charcoal dust and common salt in alternate layers) GI earth wire protected by galvanized steel pipe light grade of 15 mm dia upto switch board and connected to main switch board, including provision of 20mm dia GI tubing light grade watering pipe with funnel and wire mesh PCC earth pit (1:3:6) type C-1 covered with CI cover hinged with frame including excavation and earth work complete all as specified and shown in electrical plate No 5 of SSR Part I including testing on completion.

Disconnecting and taking out old u/s cable of service connection/sub main wire of any size and type from pole to DB's / Main switch complete all as specified

Supply and fixing in replacement sub main wiring with two single core FRLS insulated cable with copper conductor stranded and sheathed of size 6 Sq mm in and including PVC conduit including 1 x 6 Sq mm FRLS copper earth wire to common earth and connected to earth dolly complete all as specified and directed. Make of cable : Finolex/Havells/Plaza/Indo Asian

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for ltaking out old cable/laying of under ground cable/foundation of poles/stays including segregation of old serviceable bricks complete all as specified and directed by Engineer-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer complete all as specified and directed by Engineer-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr away and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engineer-in-charge.

M & L for brick protection using old size sub class 'B' bricks, laid flat dry but adjoining to each other laid lengh wise perpendicular to the axis of cable complete all as specified and directed.

Supplying, filling in trenches spreading, leveling sand cushioning 8 cm below and 15 cm above the cable for under ground cable complete all as specified & directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core.

Supply and fixing LED bldg security light fitting 15 watt Powder coated pressure die cast aluminium compact LED security light including 1.5 mtr long 40 mm bore GI pipe mounting bracket made to shape for fixing on wall with 40 mm x 6 mm flat iron clamp 02 numbers with 16 mm dia bolts, nuts and washers all as specified and directed by Engineer-in-Charge.Make- Crompton Cat Part No LSTS-15-CDL or equivalent in Bajaj/Philips/C&S/Havells : Contractor shall provide 1 years written manufactures warranty for the LED fixture complete including driver from the certified date of completion.

M/L for GI Pipe 'light grade' galvanized with all fitting laid in trenches/on pole/road crossing of size 40mm

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated Make- Bajaj/Orient/Crompton/Polar

S&F 1100 Volts grade heavy duty cable PVC insulated stranded aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4 mm suspension wire, one twin core cable flat or round of 10 sqmm cable.

S&F House service bracket (Hook type) complete with 3.0 Mtr long G.I pipe 40mm dia Med grade two Nos 90 degree bends, including MS hooks and stay or guys

Supply & fixing fan regulator electronic step type and making connections. (Make : Anchor/Leader/Bajaj).

COSMO BUILDERS

JOGRAJ CONSTRUCTION COMPANY