PROVN OF SENTRY POST COVERED SHELTER TOILET AND ASSOCIATED WORKS FOR SECURITY PERSONNEL AT MATERIAL GATE NEAR HIGHWAY AT AF STN MEMAURA

Amount

Excavation in trenches, in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundation etc or for shafts,wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m depth and getting out complete all as specified and directed.

M&L for Cement Concrete PCC 1:4:8 type D2 (using 40mm graded stone aggregate) in foundation, filling and mass concrete complete all as specified and directed

M&L for ATT treating the backfill in contact with the foundation at the rate of 7.5 Litre of emulsion per square metres of surface area complete all as specified and directed.

M&L for ATT treating the top surafe of fiiled earth at the rate of 5Litre of emulsion per square metres of surface area.

M&L for Form work to fair finished surface of sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for form work to fair finished surfaces of sides of pillars, posts, struts, piers, coloumns and stanchions complete all as specified and directed.

M&L for formwork to fair finished surface of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc, also splays between floors and beams, etc complete all as specified and directed

M&L for form work to to fair finished surface of soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed

M&L for RCC M-25 (Nominal mix) in foundations, including rafts, footings, foundation beams, plinth beams; bases for coloumns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

M&L for RCC M-25 (Nominal mix) in Columns, pillars, piers, posts and struts complete all as specified and directed

M&L for RCC M-25 (Nominal mix) in beams, cantilevers, bressurmmers, lintels over 1.5m span complete all as specified and directed

M&L for RCC M-25 (Nominal mix) in Chajjas all as specified and directed

M&L for RCC M-25 (Nominal mix) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed

M&L for mild deformed TMT steel bars 10mm dia and over, cut to lenght, bent to hsape required, including crandking, bending spirally for hooping fro columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and directed

Ditto, above but 5mm and over upto and including 10mm dia in stirrups, spacers and binders

M&L for hardcore broken bricks of gauge n exc 63mm, deposited, spread and levelled in layers n. exc 15cm thick watered and rammed to a true surface

M&L for 40 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) in sub floors, sub bases of floors finished surfaces of concrete even and rough to receive screed bed/topping layer etc complete all as specified and directed

M&L for returning,filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm complete as specified and directed.

M&L for removing excavated meterial n.exc . 50m and deposinting where directed at a level n ecxc 1.5 m above the starting point

M&L Brick work with flyash brick old size, straight or curved on plan exc 6 mtrs mean radius and built in cement mortar 1:6 all as specified.

Material & labour for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM (1:6) surfaces finished even and fair faces without using extra cement complete all as specified and directed.

M/L 15mm thick rendering in CM 1:4 with with water proofing compound on fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed. (Note- WPC Qty should be measured and paid to separately)

Supply only water proofing compound complete all as specified and directed.

Material & labour for rendering 5mm thick in cm 1:3 as in ceiling/concrete surfaces finished even & fair faces complete all as specified and directed .

M/L for roof treatment with polymeric water proofing membrane with certain specification given below as under complete all as specified & directed) (a) Cleaning and brooming the surface of roof. (b) Providing average 15mm thick plaster bed in CM(1:3) mixed with water proofing compound. (c) After the concrete is fully dried. It shall be cleaned free from dust and shall be painted with a coat of bituminous primer @ 0.40 liters/Sqm. (d) After primer, the entire roof surface shall be applied with hot blown bitumen grade 85/25 conforming to IS-702 @ 1.2 Kg/Sqm (e) Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film with standard weight not less than 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as of manufacture’s technical representation. prepared surfaces and fusing the joints with blow torch application. (f) A coat of bitumen grade 85/25 shall be applied @ 0.30 Kg/Sqm. (g)applying a tack coat of hot blown bitumen grade 85/25 @ 0.3 Kg/Sqm. (h) Apply one coat of aluminium paint (0.2kg/sqm).

M & L for prepration of new plastered or unplastered surfaces of wall applying two coats of oil bound distemper over 1.5mm thick putty complete all as specified and directed.

M&L preparing of new plastered surface of walls and applying two coats of cement base paint over cement primer complete all as specified and directed.

Material & labour for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed .

M&L for applying two coats of exterior emulsion paint white or tint on walls/ chajja/ facias/ fins on newly plastered surfaces including complete removal of existing treatment complete all as specified and directed

S&F non-skid joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but n exc 0.38 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L galzed ceramic coloured joint free tiles 450 x 350 x 6 to 7 mm/ 450x300x6 to 7mm thick on walls etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces including 10mm thick rendering in CM 1:4 complete all as specified and as directed. etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in plinth protection/ path laid in alternate panels 75mm thick finished even and smooth w/o using extra cement.

S&F factory made solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of M S tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain coloured PCV ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cementsuppling & fixing in the frame at site as per specification & drawings.

S&F factory made solid WPC door frames of size 125mm x 60 mm fixed in opening as per specification & drawing.

S & F 30mm thick Factory made Plain wiremesh PVC door shutter cosisting of frame made of MS Tubes of 19 guage thickness and size of 19mmx19mm for stiles and 15mmx15mm for top, lock and bottom rail. MS frame shall have a coat of metal primer of approved make and manufacturer. 19mmx19mm MS square tubes shall be covered with heat moulded plain sheet 'c' channel made from 5mm thick pvc sheet of density 600 kg/cum manufactuered by ISO-9001-2015 certified company of size 30mm thickness, 115mm width out of which 100 mm shall be flat and 15mm shall be bent in 90 degree angle on either side forming stiles, one of 90 degree bend edge is cut from stiles as well as rails to nails from inner side of door to hide wiremesh fixing steel screws. 5mm thick 140mm wide pvc sheet out of which 125mm shall be flat and 15mm shall be bent in 90 degree on inner side from top to bottom rail and 155mm wide pvc sheet out of which 125mm shall be flat and 15mm shall be bent in 90 on both side to from lock rail. An additional 5mm thick pvc strip of 20 mm width is to be stuck on exterior side of the C channel using PVC solvent cement adhesive . Panel will be of SS wire mesh of 24 guage to be fitted inside area of stiles and rails. The wire mesh of Top Bottom & lock rail is sealed with 15 mmx15mm tube with steel screw of size 13/16mm. 10mm (5mmx2 nos) thick pvc strip of 25 mm width is to be stuck and nail on both side of SS wiremesh interior at the top,bottom&lock rail. 10mm thick (5mmx2nos) thick, 20mm wide cross pvc sheet as gap insert for top rail & bottom rail door to be fitted to frame with 3 nos MS powder coated butt hinges size 100mmx25mmx2mm and 32mm long screw drilled suitable to pass through both the wall of MS tubes. other hardware should be fixed with 19mmx6mm size steel screw complete as specified and as dirction by Engr-IN-Charge.

S & F 30mm thick Factory made WPC door shutter with water proof, fire resistance, termitre proof etc complete as specified and as dirction by Engr-IN-Charge.

S & F Butt hinges 100mm, extruded aluminium alloy with galvanized mild steel hinge pin, anodised of type B-22 and complete all as specified and as directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section all as specified

S& F 125 mm extruded aluminum alloy handles, fabricated type anodised.

S&F Powder coated aluminium frame and shutter (minimum thickness of powder coating 50 micron) work for doors, windows ventilators and partitions (Fixed portions) with extruded built up standard tubular section of size 44.45mmx47.62mmx 1.88 mm thick and weight 0.943 Kg/Rm of approved make conforming to IS 733 and 15:1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at i.e junctions, Le at top, bottom. and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight. mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge

S & F 5.5mm thick sheet glass ground or Obscured or frosted on one side sheet glass and glazing with oil putty in square exc. 0.5 sqm in each pane all as specified

S & F 5.5mm thick sheet glass ground or Obscured or frosted on one side sheet glass and glazing with oil putty in square nexc. 0.5 sqm in each pane all as specified

Supply & fixing of vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest including of ‘P’ trap lime concrete bedding and making good floor complete all as specified and directed.

Supply and fixing of PVC low level flushing cistern 10 Ltr capacity dual flushing white with inlet , ball valve, float and handle incl brackets incl 32 mm dia PVC flush pipe for low level cistern fixed complete all as specified and dircted.

Supply & fixing of vitreous china wash hand basin, white size 550x400 mm including brackets, CP waste coupling &PVC waste pipe of 32 mm dia complete all as specified and directed.

S&F PVC Connection 15mm size with PTMT nut of length 300 mm complete all as specified.

S&F 1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

Cutting Chases for concealed water tubing etc and making good disturbed surfaces CM 1:3, cutting not exceeding 10 cm girth, on brick walls complete all as specified & directed.

Supply & laying of CPVC pipes SDR13.5 pipes & plain CPVC SDR 11 fittings in floors/walls/ceilingss for 16 mm bore complete all as specified and directed .

S&F 15 mm dia CPVC gate valves with plastic wheel head screwed both ends for CPVC pipe complete all as specified & directed.

S&F in repair 15mm bore pillar taps brass chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe, fixed in repairs complete all as specified & directed.

S&F brass chromium plated towel rail 600 mm long, 20mm dia of a approved quality, complete all as specified & directed.

S&F 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall/ laid under floor etc in waste pipes and rain water pipes incuding PVC Tee,socket elbow,clamp etc complete all as specified and directed

S&F 110mm PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall/ laid under floor etc in waste pipes and rain water pipes incuding PVC Tee ,socket,elbow,clamp etc complete all as specified and directed

S&F 75mm/110mm/125mm PVC(SWR) Gully Trap setting and jointed with solvent cement complete all as specified and dircted.

S&F Shelves for WHB Samrt PTMT-300mm long .

S&F 127mm dia CP grating with hole complete all as specified and directed.

S&F 127mm dia CP grating without hole complete all as specified and directed.

S & F Vitrous China bowl urinal full stall type white and union for discharge pipe including flush pipe complete all as specified and directed.

S & F Urinal Partition white of size 310x700mm about 40cm above floor line complete all as specified and directed

Surface excavation in soft/loose soil n. exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed

M&L Broken bricks hardcore of gauge 63mm deposited spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified

M&L for 100mm thick PCC 1:4:8 of type D-2 (using 40mm graded stone agrregate) as in sub base of floors etc complete all as specified and directed

M&L for sand filling under floors or in foundations including watering and consolidation complete all as directed.

S&F for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60mm thickness M-35 grade complete all as specified and as directed.

M&L salt glazed stone ware drain pipes laid jointed and tested complete of dia of pipe 150mm.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested bore dia of pipe 150mm in cement concrete type C-2(1:3:6)

Construction of septic tank of 10 users capacity all as specified and shown in drawing No TD/217 dt 27 Jun 1991 Sheet No 1/2 to 2/2 including excavation and earth work in any type soil, PCC 1:2:4 type B2 in floor/foundation, all brick work in wall shall be in CM 1:4 using sub class 'B' bricks, internal plaster 15 mm thick in CM 1:4, RCC M-25 (Nominal Mix) slab with reinforcement as shown in drawings, Man hole cover shall be precast reinforced concrete ,MS steps all as shown in drawin gs and two coats of bitumenous paint shall be applied on it, CI Vent/Outlet pipes including cowls shall be all as shown in drawings, Baffle wall shall be RCC M-25 (Nominal Mix) as shown on drawings complete all as directed by Engr-in-Charge

Construction of soak well 1.8m dia and 3m effective depth all as specified and shown in drawing No TD 576 dt 16 Jun 89 Sheet No 1/2 to 2/2 including excavation and earth work in any type soil, PCC 1:3:6 type C2 in foundation, Dwarf wall shall be of PCC 1:4:8 type D2, brick work in wall shall be in CM 1:6 using sub class 'B' bricks and honey comb shall be in CM 1:4, RCC M-25 (Nominal Mix) slab with reinforcement as shown in drawings, Band shall be PCC 1:2:4 type B1 and brick bats shall be with hand broken bricks of gauge not exceeding 100 mm complete all as directed by Engr-in-Charge

Material and labour for point wiring with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volt FRLS grade ISI marked with multistranded copper conductor drawn through and including medium grade PVC conduit (suitable size) concealed in wall with provision of 1.5 sqmm single core cable green in colour PVC insulated copper conductor as earth continuity conductor connected to earth dolly for following:-

One light point/fan point/ex fan point controlled by one 5 Amps switch one way

One 3 pin 5 Amp switch socket outlet on independent board with accessories

All as per item No 1 here in before but for one socket out let 2in1 5 and 15 Amps with 2.5 Sqmm PVC insulated copper conductor and provn of 2.5 sqmm PVC insulated single core copper cable green in colour as earth continuity conductor.

S&F switch piano 1 way 6 Amp, 1 module, 240 volts, complete all as specified and as directed.

S&F socket out let 3 Pin 6 Amp, 2 module, 240 volts, complete all as specified and as directed.

S&F socket combination 2 in 1 , 3 pin 6 & 16 Amp, 3 module, controlled by one switch, 240 volt, complete all as specified and as directed.

Supply and fix ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body.

S & F Wall/surface mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired, connecting up with 3 core twisted flexible copper conductor cable, including taking down old u/s fitting. complete all as specified and as directed.

S & F LED lamp of 9W and colour temp 6500K suitable to fix in batten hoder, complete all as specified and directed.

S&F 20 W powder coated PPC aluminium LED building light fitting having Ingress Protection class IP-65 , with high power LED complete with 32 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos M.S. Flat (25mmx5mm) clamps, nuts, bolts, washers etc. all as specified and as directed.

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings. complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). Complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m including PVC insulated 3 core 1.5 sqmm copper cable from ceiling rose to exhaust fan. Complete all as specified and as directed.

Supply and fixing SPN MCB DB 4 way double door type single phase with common earth and neutral bus bars, 240 volts complete all as specified and as directed.

Supply and fixing SPN MCB 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and current carrying capacity 6 to 32 amp in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

M&L for earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5mm graded stone aggregate reinforced with 6 mm dia round bar @ 75mm C/C both ways with MS handle 8mm dia, plastering 15mm thick CM (1:6) externally upto 150mm below ground level , GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing and marking Bldg Nos and writing Test Results on a 3.0mm thick painted M.S. earth pit marking Plate (200mm x 100mm) duly welded with a 450mm long 10mm dia round M.S. rod, fixed with the earth pit chamber by grouting complete including taking out old unserviceable earthing system including demolishing with old earth pit chambers and removing of debris from the site with levelling the ground all as specified an directed.

m/s pal associates