REPAIR/ REPLACEMENT TO PIPE LINE AND PUMPS MOTORS AND DG SETS AT KHANPUR DUNDAHERA AND MANESAR ARMY CAMP UNDER AGE E/M (S) AND REPAIR TO ROOF SHEET STEEL WINDOW FALSE CEILING DOORS SANITARY AND PLUMBING FITTINGS FLOORING PLASTERING AND MISC B/R WORKS

Amount

E/M Works M&L cleaning of semi under ground sump of storage capacity of water up to 25000 gallons thoroughly by removing mud, dirt etc. from the sump by the following method complete all as per specified and directed by Engineer-in-Charge. (a) Cleaning inner surface of the tank by scraping with steel wire brushes and removing mud and sludge collected in and outside of the tank and removing sludge to a distance not exceeding 50 meter. (b) Washing with clean water thoroughly complete tank internally and finally cleaning with bleaching powder. (c) writing date of cleaning on the sump.

S&F in replacement of GI water tubing, medium grade, galvanised (ISI marked as IS-1239), with all fittings including short lengths, fixed to walls, fixed in sewage well, U/G sump,concealed in wall and ceiling or laid in floor trench complete with all fittings (such as bends, elbows,flanges Tee, short pieces,reducer,nipple, connectors, back nuts, diminishing pieces, caps and plugs, unions etc), complete all as per specified and directed by Engineer-in-Charge of the following sizes:-

100 mm bore

80mm bore

50mm bore

40mm bore

25mm bore

20mm bore

S&F in replacement of 100mm CI pipe class B with all fittings in any length fixed to walls and ceiling or laid in trenches.

S&F in replacement of following items/accessories in existing position complete all as per specified and directed by Engineer-in-Charge the following sizes:-

GI union 100 mm bore

GI union 75/80 mm bore

GI union 40/50 mm bore

GI union 20/25 mm bore

GI socket 100 mm bore

GI socket 75/80 mm bore

GI socket 40/50 mm bore

GI socket 20/25 mm bore

GI elbow 100 mm bore

GI elbow 75/80 mm bore

GI elbow 40/50 mm bore

GI elbow 20/25 mm bore

GI End plug 40/50 mm bore

GI End plug 20/25 mm bore

GI Tee 80/50 mm bore

GI Tee 40/50 mm bore

GI Tee 20/25 mm bore

GI Flange 80 mm dia

GI Flange 50 mm bore

M&L for run lead joint for any bore suitable for spigot socket GI/CI pipe including taking down old unservicable lead joint including necessary excavation and earth work complete all as specified and directed by Engineer-in-Charge.

M&L AL- TOCH-GP (Calcium based granular disinfectant) for water treatment in packing of 45 Kg drum of manufacture complete all as specified and directed by Engineer-in-Charge.

M&L for cutting of existing CI pipe in trenches of size 75/80/100 mm bore for new branch connections including necessary excavation and eath work complete all as specified and directed by Engineer-in-Charge.

M&L cutting of existing GI pipe in trenches of size 80/50/40 mm dia for new branch connections including necessary excavation and earth work complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement of old unserviceable overload relay suitable for 15 HP motor starter complete all as specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s relay and make the connection after replacement of realy.

S&F in replacement of old unserviceable overload relay suitable for 25 HP motor starter complete all as per specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s relay and make the connection after replacement of realy.

S&F in replacement of old unserviceable overload relay suitable for 10 HP motor starter complete all as per specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s relay and make the connection after replacement of realy.

S&F in replacement of old unserviceable contactor suitable for 25 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s contactor and make the connection after replacement of contactor.

S&F in replacement of old unserviceable contactor suitable for 15 HP motor starter complete all as per specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s contactor and make the connection after replacement of contactor.

S&F in replacement of old unserviceable contactor suitable for 10 HP motor starter complete all as per specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s contactor and make the connection after replacement of contactor.

S&F in replacement of old unserviceable single phase preventor suitable for 25 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s single phase preventorr and make the connection after replacement of single phase preventor.

S&F in replacement of old unserviceable single phase preventor suitable for 15 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s single phase preventorr and make the connection after replacement of single phase preventor.

S&F in replacement of old unserviceable single phase preventor suitable for 10 HP motor starter complete all as per specified and directed by Engineer-in-Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s single phase preventorr and make the connection after replacement of single phase preventor.

S&F in replacement of old unserviceable phase sequencer suitable for 25 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s phase sequencer and make the connection after replacement of phase sequencer.

S&F in replacement of old unserviceable phase sequencer suitable for 15 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s phase sequencer and make the connection after replacement of phase sequencer.

S&F in replacement of old unserviceable phase sequencer suitable for 10 HP motor starter complete all as specified and directed by Engineer -In- Charge. Note:- The rate is inclusive of connection out the starter before replacement of old u/s phase sequencer and make the connection after replacement of phase sequencer.

S&F in replacement of old unserviceabel digital voltmeter of range 0-500 volts suitable for motor starter of capacity upto 15 HP complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement of old unserviceabel digital voltmeter of range 0-100 Amps suitable for motor starter of capacity upto 15 HP complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement of old unserviceable indication lamp for motor starter complete all as per specified and directed by Engineer-in-Charge.

M&L for Lifting of submersible pumping set of any capacity from deep bore well with chain and pulley arrangement including lowering down the submersible pump set after repair complete all as per specified and directed by Engineer-in-Charge.

M&L complete overhauling/repair of defective submersible pump of 5-7.5 HP and replacement of following spares of pumps of capacity 5HP to 7.5 HP,12 stage, 3 phase motor driven (excluding motor) cast iron/cast steel body complete and connecting with motor portion complete all as per specified and directed by Engineer-in-Charge.

CI connection piece.

CI Stage bowl.

GM neck ring.

Remetling of GM impeller turning.

GM DOL bush.

SS stud with nut.

Water seal

Revolving disc

EPV Impeller.

Impeller key.

Repairing of stamping of stator.

CI DOL piece.

SS coupling with key.

CI Suction piece.

GM sand guard.

All as per Srl item number above 28 here-in-before but 10-12.5 HP capacity complete all as specified and directed by Engineer-in-Charge..

CI connection piece.

CI Stage bowl.

GM neck ring.

Remetling of GM impeller turning.

GM DOL bush.

SS stud with nut.

EPV Impeller.

Impeller key.

Repairing of stamping of stator.

CI DOL piece.

SS coupling with key.

CI Suction piece.

GM sand guard.

M&L in replacement for re-winding of motor of submersible pump set of 5HP to 7.5 HP capacity with suitable size copper conductor wire including insulating material and transportation of the repair motor of MES installation to workshop and back complete all as per specified and directed by Engineer-in-Charge. Note:- The quoted rate shall be deemed to be inclusive of transportation charges from site to workshop and back.

M&L in replacement for re-winding of motor of submersible pump set of 10HP to 12.5 HP capacity with suitable size copper conductor wire including insulating material and transportation of the repair motor of MES installation to workshop and back complete all as specified and directed Note:- The quoted rate shall be deemed to be inclusive of transportation charges from site to workshop and back.

S&F in replacement of following spares of motor of capacity 5 HP to 12.5 HP complete all as per specified and directed by Engineer-in-Charge.

GM bearing bush.

SS Tuter sleeve.

Cable seal.

Thrust bearing.

Thrust Plate

Sealing Ring.

Motor seal 10 mm

Motor seal 25 mm

O ring

CI Lower housing.

CI upper housing.

Remetling of rotar & turning.

S\&F in replacement submersible cable flat 6 Sqmm 3 core for bore well of any depth with fitting and connections complete all as per specified and directed by Engineer-in-Charge.

M&L for Lifting of motor/ pumping set from the existing sewage well of any depth with chain and pulley arrangement and lowering down the motor/pumping set after repairing complete all as specified and directed by Engineer-in-Charge.

Taking out Manhole cover and Desludging the existing manhole septic tank including removing of Sludge/Mud/Muck, Desilting/Dechocking with combine high pressure water jetting cum suction (Vaccum) type machine mounted on LCV/HCV and disposed off outside MD land and blocking of the sewage line of septic tank to stop the entry of waste water/sludge/mud in sewage well. Complete all as specified and directed by Engineer-in-charge.

M&L for disposal of waste water up to 06 feet depth of Sewage well and 04 Feet depth of Man Hole by using Portable sewage pumping set of capacity 12 HP and filling of waste water in a covered trolley and disposed off outside MD land complete all as per specified and directed by Engineer-in-Charge.

M&L for removal of Sludge/Mud/Muck/Waste material/Silt upto a depth of 14 feet in mainhole/ sewage line , Desilting/Dechocking with high pressure super socker machine and cleaning of surface of sump of sewage well using wire brushes and other scrapping tools to remove dirt and scales to make it free from all deposits and disposed of the same to outside MD land complete all as per specified and directed by Engineer-in-Charge.

Opening of Manhole cover and connecting of the sewage line of septic tank with sewage well complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement for nuts, bolts, rubber gasket complete set complete all as specified and directed by Engineer-in-charge.. Note :One job shall be inclusive of all nuts, bolts, washers and rubber gasket required for lifting/lowering of pipe line for one pumping set.

M&L for preparation of monoblock pump of capacity up to 15HP at site and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as per specified and directed by Engineer-in-Charge.

M&L for rewinding of the monoblock pumpset of 5 HP to 7.5 HP capacity with suitable size copper conductor wire including insulating material and transportation of the repair motor of MES installation to workshop and back complete all as per specified and directed by Engineer-in-Charge. Note:- The quoted rate shall be deemed to be inclusive of transportation charges from site to workshop and back.

M&L for rewinding of the monoblock pumpset of 12.5 HP to 25 HP capacity with suitable size copper conductor wire including insulating material and transportation of the repair motor of MES installation to workshop and back complete all as per specified and directed by Engineer-in-Charge. Note:- The quoted rate shall be deemed to be inclusive of transportation charges from site to workshop and back.

S&F in replacement of following spares of booster pumping set of capacity upto 15 HP complete all as specified and ditected by Engineer-in-Charge.

bearing

brass Impeller

Glands packing

Alignment of motor shaft including Lathe work complete all as specified and directed.

Supply only chlorine water testing chloroscope type kit for testing of water complete all as per specified and directed by Engineer-in-Charge.

M&L for servicing to DG set of capacity up to 35 KVA as per manufacturers direction/description including oiling, cleaning & greasing complete all as per specified and directed by Engineer-in-Charge. Note:- (Spares shall be measured & paid separately under respective item)

M&L in replacement of oil filter set for 20 to 35 KVA DG set complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement starter key switch for 20 to 35 KVA DG set complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement of Battery Terminal made of brass nut & bolt complete all as per specified and directed by Engineer-in-Charge.

Repair and calibration to fuel injection pump & nozzle for 20 to 35 KVA DG set complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement of fuel filter set for 20 to 35 KVA complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement of pipe (Fuel line) set for 20 to 35 KVA complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement of radiator hose pipe set for 20 to 35 KVA complete all as per specified and directed by Engineer-in-Charge.

M&L in replacement engine oil as per manufacturers suggested grade complete all as per specified and directed by Engineer-in-Charge.

Topping up of coolant complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement of temperature gauge for DG Set complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement Off load Changeover Switch - AC 23 (side handle) in sheet enclosure, 415 Vac, 50 Hz. 4 pole 100 Amp/415 volts on load side handle operated type complete all as per specified and directed by Engineer-in-Charge. Make:- Cat Part No IHBFFE0100 of Havells or its equipvalent HPL/L&T/Standard.

S&F in replacement gunmetal globe or gate valve/sluice valve for 150 mm (6 inch) bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Kartar

S&F in replacement gunmetal globe or gate valve/sluice valve for 100 mm (4 inch) bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Kartar

S&F in replacement gunmetal globe or gate valve/sluice valve for 80 mm (3 inch) bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Kartar

S&F in replacement gunmetal globe or gate valve for 40 mm bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. .Make Leader/Jindal/Kartar

S&F in replacement gunmetal globe or gate valve for 25mm bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Kartar

S&F in replacement gunmetal globe or gate valve for 50 mm bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Sant

S&F in replacement and testing of Foot Valve confirming to IS 4038 complete of size 80mm (3") dia complete all as per specified and directed by Engineer-in-Charge.

S&F in replacement connect and test, Valve, reflex (non return), with bypass arrangement complete of size 150mm dia (6") dia including all fixing materials like rubber gasket, nuts, bolts, washer etc complete all as per specified and directed by Engineer-in-Charge. Make:-Leader/Jindal/Kartar.

S&F in replacement connect and test, Valve, reflex (non return), with bypass arrangement complete of size 100mm dia (4") dia including all fixing materials like rubber gasket, nuts, bolts, washer etc complete all as per specified and directed by Engineer-in-Charge. Make:-Leader/Jindal/Kartar.

S&F in replacement connect and test, Valve, reflex (non return), with bypass arrangement complete of size 80mm dia (3") dia including all fixing materials like rubber gasket, nuts, bolts, washer etc complete all as per specified and directed by Engineer-in-Charge.. Make:-Leader/Jindal/Kartar.

S&F in replacement butterfly valve for 80 mm bore pipe, with iron wheel head screwed both end complete all as per specified and directed by Engineer-in-Charge. Make Leader/Jindal/Sant

S&F in replacement of battery 180 Ah,12 Volts maintencance free including battery termail alongwith connectiing wire of suitable gauge upto 2 mtr length min as required on site complete all as per specified and directed by Engineer-in-Charge. Make:- Exide/Amaron/ Luminious.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for laying of cables or other items and getting out soil in soft/loose soil complete all as per specified and directed by Engineer-in-Charge.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as per specified and directed by Engineer-in-Charge.

Removing excavated material not exceeding 50 mtr and depositing where directed in a level not exceeding 1.5 mtr above the starting point of any type of soil complete all as per specified and directed by Engineer-in-Charge.

M&L for construction of valve pit of size 90 cm x 90 cm x 1.0 m (internal dimensiions), stone/ brick construction, including all necessary excavation and earth work in any type of soil, returning, filling in disposal of surplus soil to distance not exceeding 50 m and depositing where directed, PCC in foundation of the mix (1:2:4) type D-2, brick masonary in cement mortor (1:4) rendering 12 mm duck in cement mortar (1:4) internally, finished even and smooth and pointing flush externally as the work proceeds in the same mortor. Mild steel angle iron 40 x 40 x 6mm frame MS sheet cover 3.15 mm thick with handle and locking arrangement, painting all the exposed MS work with two coats of synthetic enamel paint of the that as approved by the GE over a cost of red oxide primer and painting all the MS embedded in PCC with two coats of black bitumenous paint and complete all as per specified and directed by Engineer-in-Charge.

S&F ball brass valves of 25mm ,high pressured,with polythene float, flynut,screwed for iron pipe or brass ferrule complete all as per specified and directed by Engineer-in-Charge.

B/R Works Taking down door chowkhat or frame with shutters (without taking off shutters from the frame exc 1.5 sqm but nexc 4 sqm each complete all as per specified and directed by Engineer-in-Charge.

Taking down door/window chowkhat or frame with shutters (without taking off shutters from the frame n.exc 1.5 sqm each complete all as per specified and directed by Engineer-in-Charge.

S&F 2nd class 35 mm thick hardwood glazed and skelton shutters open rebated and prepared to receive glass / gauze etc ( with or without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 cluse 8.24(a) complete all as per specified and directed by Engineer-in-Charge.

S&F factory made 2nd class hard wood 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as per specified and directed by Engineer-in-Charge.

S&F 100mm long butt hinges stainless steel complete all as per specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium window frame / wooden doors or steel section windows complete all as specified complete all as per specified and directed by Engineer-in-Charge.

S&F 200mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge

S&F for ISI marked 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as per specified and directed by Engineer-in-Charge.

S&F aluminium alloy handles extruded, fabricated type, anodised ,of 150mm size. complete all as specified and as directed by Engineer-in-Charge

S&F aluminium alloy handles extruded, fabricated type, anodised ,of 125mm size. complete all as specified and as directed by Engineer-in-Charge

S&F floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring of 140 mm size with vulcanised rubber piece. complete all as per specified and directed by Engineer-in-Charge.

S&F rolled mild steel in Fe 410-W(Gde-E-250) quality-A, framed work as in doors or gates of angle or other section with gusset plates, etc., complete, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete all as per specified and directed by Engineer-in-Charge.

S&F solid PVC doors & frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm MS square tube of 19 guage s&f in opening as per specification & drg in SSR 2004 Part II complete all as per specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be coloured with heat mould plain coloured PVC'C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stills and plain colour PVC sheet for top rail lock and botton rail either side and as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading. And jointed together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as per specified and directed by Engineer-in-Charge.

S&F 100 mm size butt hinges medium weight cold rolled mild steel complete all as per specified and directed by Engineer-in-Charge.

S&F aluminium alloy anodised,barrel tower bolts of extruded section, of size 100mm. complete all as per specified and directed by Engineer-in-Charge.

BLANK

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as per specified and directed by Engineer-in-Charge.

S&F Mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as per specified and directed by Engineer-in-Charge.

S&F Sheet glass,3mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane complete all as per specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of pink primer complete all as per specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as per specified and directed by Engineer-in-Charge.

S&F in repair drapery rod mild steel powder coated teak wood finish 30mm internal dia & 0.90mm thick with wooden rings and teak wooden brackets and teak wood side knobs all as per sample complete all as per specified and directed by Engineer-in-Charge.

Dismantling of asbestos cement (corrugated or semi corrugated etc) sheet in roof covering including ridges, hips, valley gutters etc complete all as per specified and directed by Engineer-in-Charge.

S&F pre-painted Trapezoidal profile galvalume aluminium zinc coating steel sheet (Make: Tata bluescope/ Jindal ) 0.50mm thick (base metal thickness) of any colour having tensile strength of 550 Mpa minimum yield strength conforming to IS - 513 (1994) coated with hot dip alloy of 55% aluminium + 43.50%Zinc +1.50% silicon and finished with resin coat ( of thickness not less than 35 micron) on both surface @150gm/sqm of coating (total both surfaces) of approved colour as in roof covering/cladding, fixed with self tapping screws (make hilty/fissers), neoprene and epdm washers class 3 of AS-3566(5.5-14X5 for crest and 5.5-14X25 for valley fixed) with 150mm end lap and one corrogation side lap whereever required penetrations and lap in sheet shall be sealed by using proper sealant profile/HDPE fillers shall be provided whereever required to close voids between sheets and fastners etc. as in roof covering/ cladding in straight or curved surface in any height including necessary MS frame structure ie. MS vertical member , truss / purline / rafter etc of complete all as per specified and directed by Engineer-in-Charge. Note : The colour of sheet for bldg shall be approved by GE. The length of sheet shall be as per site reqiurment.

Dismantling mild steel Work of any description fixed in any posn not otherwise provided for complete all as per specified and directed by Engineer-in-Charge.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Hard/ Dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m & making good surface complete all as per specified and directed by Engineer-in-Charge.

S&F Mild steel framed work using angle iron ,flat iron fillet etc including necessary cutting,drilling,welding as required complete all as per specified and directed by Engineer-in-Charge.

BLANK

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters etc of roof covering fixed with self tapping screws complete all as specified & directed by Engineer-in-Charge.

S&F in repairs 16 mm thick of size 600x 600 mm mineral fibre false ceiling system of pattern classic lite RH 99 (bevelled tegular) of Armstrong or equivalent make as approved by GE and model including grid system using hot dipped galvanised steel section, exposed surface with pre-powder coated capping, main runner and cross runner and to comprise main tee/runner 15mm x 38 mm size (load carrying capacity 14 kg/sqm) spaced at 1200 mm centres securely fixed to the structural soffit and flush fitting 1200 mm long cross tee/runner to be interlocked between main runners at 600 mm centre to centre form 1200 x 600 mm module, cut sub cross tee/runner 600 mm require independent support. Wall angle of size 19 mm x 19 mm, secured to the periphery of the wall at 450 mm maximum centres. The above grid is suspended at every 1200 mm centre to centre in both direction and starting from wall at the distance 350 mm from wall by using 3.50 mm dia aquline wire with suitable fasterners and hook clip complete all as per specified and directed by Engineer-in-Charge.

Demolition of lime concrete or cement concrete including tilling etc in ground floors and pavings not exc 15cm thick (below or above ground level) complete all as per specified and directed by Engineer-in-Charge.

M&L for 75 mm thick plain cement concrete 1:3:6 type C2 (using 40 mm graded stone aggt) as in sub base of floor / plinth proctions etc finished surface fair & even all as specified and directed.

M&L for forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as per specified and directed by Engineer-in-Charge.

S&F machine cut kota stone slab flooring 18-20 mm thick laid over 15 mm thick cement screed base 1: 6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as per specified and directed by Engineer-in-Charge.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 13014 complete all as per specified and directed by Engineer-in-Charge.

M&L for 50 mm thick sand filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as per specified and directed by Engineer-in-Charge.

M&L for machine pressed precast concrete rubber moulded colour interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as per specified and directed by Engineer-in-Charge.

M&L for PCC ( 1 : 2 : 4) type B-1 as in kerbs coping paddings etc including necessary form work complete all as per specified and directed by Engineer-in-Charge.

Demolition of brick work built in CM incl quoins, arches, pillers etc complete all as per specified and directed by Engineer-in-Charge.

M&L for brick work in cement mortar (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as per specified and directed by Engineer-in-Charge.

Taking down cement plaster including racking out joints hacking for key scrubbing down with water etc on walls and ceiling complete all as per specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick on any faces of brick work or concrete surfaces in cement mortar 1:6 on wall surfaces and finished surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

M&L for rendering 15 mm thick on any faces of brick work or concrete surfaces in cement mortar 1:4 on wall surfaces and finished surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

M&L for 5 mm thick rendering in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as per specified and directed by Engineer-in-Charge.

M&L for 3 coats of white wash on ceiling including preparation of surface over newly plastered surface complete all as per specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces as on wall and applying two coats of cement based paint complete all as per specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali-resistant primer over a coat of Birla Wall Putty or equvalant complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from walls and applying three coats of white wash complete all as per specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from ceiling and applying three coats of white wash complete all as per specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment from walls and applying two coat of oil emulsion distemper white or tinted over a coat of primer with and including 3mm thick wall care putty including scaffolding arrangement, trestles, ladders etc all as specified and directed.

M&L for complete removal of old surface of wall and applying two coat of cement base paint over a coat of primer including scaffolding arrangement, trestles, ladders etc complete all as per specified and directed by Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing removing serviceable to store and rabbish off the premises complete all as per specified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles7 to 8 mm thick Square or ractangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match. Incl 15mm thick screed bed or bedding layer in cm 1:6 etc complete all as per specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 300x450mm 6 mm to 7 mm thick in walls etc set and jointed in neat cement slurry and pointing in coloured cement all as specified incl 10 mm thick cement mortar (1:4) as screed plaster complete all as per specified and directed by Engineer-in-Charge.

S&F in repair Vitreous China, pedestal pattern wash down water closet pan, white including fixing bolts, connection to flushing cistern and flush pip & drain pipe (or out goingpipe) and to flushing pipe, anti-syphonage pipe,& S or P trap etc complete all as per specified and directed by Engineer-in-Charge.

S&F in repair plastic water closet seat, white, closed pattern ( seat & cover for Pedestal pattern) with flat bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china ware wash hand basins, white flat size 550x400mm excluding taps but including CP waste 32mm coupling and brackets complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs PVC valve less syphonic double action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve, float and handle including brackets and connection to pipes and fixing of chain and pull or lever if any complete all as per specified and directed by Engineer-in-Charge. Make :- Cera / Parryware/ Hindware.

S&F in repairs 15 mm bore fancy type chromium plated angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipecomplete all as per specified and directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type chromium plated with long shank and cup (concealed type ) stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs 15mm bore brass chromium plated long body fancy bib taps high pressure screwed for iron pipe and fixed..etc complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs PVC connection 15mm dia and 45cm long with washers complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs 32mm dia and 61 cm long PVC waste pipe for WHB complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs CP brass shower rose of size of 100 mm dia fixed to 15mm pipe of revolving type complete all as per specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated fancy pillar taps 15 mm, screwed down high pressure, screwed for iron pipe and fixed complete all as per specified and directed by Engineer-in-Charge.

S&F in repairs Cast iron floor trap with CP grating including jointing to waste pipe in run lead, dia of outlet 75 mm in cement concrete type B1 (1:2:4) complete all as per specified and directed by Engineer-in-Charge.

S&F in repair tubular towel rail brass chromium plated, 20mm dia, ‘D’ type 60cm long between flanges complete all as per specified and directed by Engineer-in-Charge.

S&F in repair CP health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete all as per specified and directed by Engineer-in-Charge.

Taking up or down 15mm dia GI tubing and connection incl cleaning for refixing or removal to store complete all as per specified and directed by Engineer-in-Charge.

All same as per item No 145 here in before but 20mm dia.

S&F GI tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 15 mm dia bore complete all as per specified and directed by Engineer-in-Charge.

All same as per item No 147 here in before but 20 mm bore pipe

S&F in repair rotational moulded polythelene water storage tank triple layered (cylindrical vertical with closed top) hoisted and fixed in position of 500 tr capacity including taking down old with and incl 15mm brass float valve complete all as spd in SSR complete all as per specified and directed by Engineer-in-Charge. Make:- Sintex/Rotex/Polywell

M&L for Flush pointing to brick laid flat or bricks tiles in paving in CM 1: 3 complete all as per specified and directed by Engineer-in-Charge.

Note:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

Balaji Constructions

M/S.Parmod Johar

P R Constructions