Spl repair to bldg No-P-19 and P-116 of RIMC,grenade range at Raipur and provn of Guard room at gate No 1and 2 of 9 Mahar, storage Accn at Cadet Mess and day light system in multipurpose hall at RIMC of AGE B/R-I under GE Dehradun

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) (using old size bricks) complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:4) (using old size bricks) complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius built in cement mortar (1:4) as in half brick thick wall (using old size bricks) complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L rendering 15m thick on fair faces of brick work in CM 1:4 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L rendering 15m thick on fair faces of brick work in CM 1:6 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L for applying wall care putty 2 to 3 mm thick interior grade and rubbing with sand paper on plastered surfaces of walls after preparation of surfaces complete all as specified and directed

M&L for preparation of new plastered /POP/ putty surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for preparation of new plastered /POP/ putty surfaces of walls and applying two coats of cement base paint over a coat of suitable primer complete all as specified and directed by Engr-in-charge

M&L for preparation of old plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed by Engr-in-charge

M&L for preparation of new plastered surface of wall etc and applying three coat of white wash , complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered surface of ceiling etc and applying three coat of white wash , complete all as specified and directed by Engr-in-charge.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamal Paint complete.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of PU paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-In- Charge

M & L 10 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling, surface finished fair and even complete.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), and removing rubbish off the MD land complete all as specified.

Demolition of cement concrete in ground floor and paving nexc 15cm thick (below or above ground level ) and removing rubbish off the MD land complete all as specified.

Demolition of cement concrete of any description not other wise specifically provided for all as specified and directed.

M & L for Glazed ceramic coloured tiles of size 300X200 mm X 6- 7 mm thick or 250X375 mm X6- 7 mm thick or other size, on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with colour cement to match the surface including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 (usng 20 mm graded stone aggregate) as in floors to receive tiles etc, complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in coping,roof curb, padding/benching to roof/chhajja etc. and the like including necessary form work complete all as specified and directed..

M & L for 75mm thk PCC 1:3:6 type C-2 as in plinth protection, finished even and fair without using extra cement. The plinth protection shall be laid in alternate bays nexe 2 sqm with 10mm wide joints filled with bitumen mastic comprising of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

M & L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified and directed.

M & L for cement concrete ( 1:3:6 ) type C1 (using 20 mm graded stone aggregate) as in surface channels and drains and benching, forming fair finished channel for drain using extra cement including necessary form work complete all as specified.

M & L for 75 mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base or leveling course of floor etc. complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surface complete all as specified

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions in fair finished surface of concrete complete all as specified and directed.

M&L for cement concrete in Type A-1 (1:1.5:3) (using 20mm graded crushed stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified

M & L for RCC(1:1.5:3) type A-1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and strut etc,complete all as specified and directed.

M & L for RCC(1:1.5:3) type A-1 (using 20 mm graded stone aggregate) as in chajjas etc,complete all as specified and directed.

M & L for formwork to chajjas, troughts and similar items including edges for fair finished surface of concrete complete all as specified and directed.

M & L for formwork to edges of concrete flats, break in floors, treads, window cills, concrete railing and similar items n exc 20 cm wide and side of RCC/PCC bands in walls exc 10 cm but n exc 20 cm wide for fair finished surface of concrete complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering incl ridge, velly gutters complete all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directe by the Engr-in-Charge.

S&F Pre painted galvalume aluminium zinc coating GI based steel plain sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge made to profile of roof sheet, wall cladding ,gutter pipe etc fixed with self tapping screws as specified all directed by the Engr-in-Charge.

S&F tiled false ceiling of Designer tile Ivory painted (High PressureSteam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of

All as per item No 44.00 (Contd/--)...1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights as per direction of Engineer-in-Charge.

S & F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc with out sash bars , edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

M&L for 30 mm thick, factory made BWR flush shutters, solid core construction, with block board core and plywood face pannels commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and as directed

S&F Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F factory fabricated steel ventilator with top hung shutter including hinges, steel peg stay, handle ,complete all specified and directed.

S&F pre laminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing.

S&F Factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I.

S&F pressed steel frames for doors of size 165 X 60mm with one or more rebates including necessary fittings lugs, hinges, lock strike plate,hold fast and PCC on hingle to fixet with machine screws and Ms flat on back side of frame including backing etc complete all as specified and directed by Engr-in-Charge

S&F pressed steel frames for doors of size 105 X 60mm with one or more rebates including necessary fittings lugs, hinges, lock strike plate,hold fast and PCC on hingle to fixet with machine screws and Ms flat on back side of frame including backing etc complete all as specified and directed by Engr-in-Charge

S&F Mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or stainless steel wire staples all as directed by Engeer-in-charge.

S&F 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane all as directed by Engeer-in-charge.

S&F 4 mm thick figured glass, pin headed ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane all as directed by Engeer-in-charge.

S&F mild steel framed work as in grill, grating etc framed guard bars, barred iron doors, ladders, frame balusters, walk ways, railing. framed work of water tanks and similar works confirming to Fe 290 Gde E165 complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, medium weight, cold rolled and fixed with mild steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel, 202 grade ,bright finish barrel tower bolts of 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel ,202 grade ,bright finish barrel tower bolts of 10 mm dia shoot, complete all as specified and directed.

S&F 150mm size solid in one piece stainless steel handles, D type all in 202 grade and fixed in stainless steel screws complete all as specified and directed by Engr-in-Charge.

S&F 250mm long stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and complete all as specified as directed.

M&L for broken stone hard core of gauge n. exc. 63mm deposited, spread and levelled in layer n. exc. 15cm thick watered and rammed to a true surface complete all as specified and directed

S & F 300 mm mild steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete all as specified as directed.

S&F 25 mm dia thickness 1mm stainless steel 202 grade curtain rod with bright nickle decorative finnial and fixed to wall with PVC dash fastner complete all as specified and directed by Engr-in-charge . Note : Cost of one pair of side brackets is inclusive in the rate per metre length of curtain rod

M&L for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in lintel upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work, complete all as specified and directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified as directed.

Supply and fixing PVC connection 15 mm dia 450 mm long with PTMT nuts at both ends complete all as specified as directed.

S&F viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap fixed with epoxy mortar (Asian/Berger), set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge

S&F 08 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve including PVC flushing bend 600 mm long and fixing with WC complete complete all as specified and directed by Engr-in-charge (Make commander/Cera/Hindware/pearl).

M&L 40mm thick Damp proof course horizontal surfaces incl necessary form work in PCC (1:2:4) type B-0 (using 12.5 graded crushed stone aggregate) mixed with water proofing compound as per manufacturers recommendation complete all as specified and directed. (Water proofing compound shall be measured and paid separately)

M&L for Non skid ceramic coloured tiles square/rectangular of 7 to 8mm thick, area of each tile exceeding 0.06 sqm but not exc. 0.11 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the shade of tiles incl screed bed of 15 mm thick in CM (1:6) complete all as specified and directed.

M&L for Non skid ceramic coloured tiles square/rectangular of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18 sqm as in floor etc. set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the shade of tiles incl screed bed of 15 mm thick in CM (1:6) complete all as specified and directed.

S&F vitreous china wash hand basin, white flat back, size 550x440mm excluding taps but including PTMT waste fittings 32mm size long shank & PVC waste pipe and MS brackets all as specified and directed by Engr-in-charge Make: Make :Cera / Hindware /Parryware .

S&F Pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaquar Cat part No. VGP81001 / Hindware -F370001 / Parryware -EDGE G4802A1.

S&F brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F concealed stop cock, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make :Jaquar/Hindware/Parryware

S&F angle/ stop valve, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : - Jaquar Cat Part No FON-40053 / Hindware Cat Part No F160017 / Prayag 9410

S&F 15mm bore Bib taps short body, cast copper alloy fancy type chromium plated with, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - Jaquar ALI-85037/Hindware F-370004/ / Prayag cat No-9906.

S&F brass chromium plated towel rack 60 cm long fixed complete all as specified and directed. Make : Jaquar AKP 35781PS or equivalent of Hindware/Parryware

S&F rotational moulded polyethylene water storage tanks 500 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float , complete all as specified and directed.

S & F 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S&F 100 mm bore cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors or fixed to walls, complete all as specified and directed by Engineer-in-Charge

S&F 75 mm bore cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors or fixed to walls, complete all as specified and directed by Engineer-in-Charge

S&F cast iron cowls 75 mm complete all as specified and directed by Engineer-in-Charge

S&F cast iron cowls 100 mm complete all as specified and directed by Engineer-in-Charge

S&F100 mm bore cast iron bends of (any radius), dimnishing pieces or taper (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge

S&F for 75 mm bore cast iron bends of (any radius), dimnishing pieces or taper (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer-in-Charge

S&F for 100 mm bore cast iron branch piece , single (equal or unequal) ordinay or inverted (spigot or socket type ) with or without parallel branches complete all as specified and directed by Engineer-in-Charge

S&F for 75 mm bore out let cast floor trap with gratings including jointing to waste pipe fixed in cement concrete type (B-1) 1:2:4 etc complete all as specified and directed by Engineer-in Charge

S&F 150x150 mm SGSW gully trap square or round mouth & jointing with solvent cement including mild steel cover complete all as specified and directed by Engineer-in-Charge

S&F100 mm bore cast iron bends of (any radius) with duck's foot or heel rest, complete all as specified and directed by Engineer-in-Charge

S&F for 75 mm bore cast iron bends of (any radius) with duck's foot or heel rest, complete all as specified and directed by Engineer-in-Charge

Supply and fix grating stainless steel, 302 grade, 150x150 mm with/without hole fixed with cement mortar , complete all as specified and directed by Engr-in-charge. Make- Prayag cat No-FT-29. or equivalent.

S& F stack clamp of flat iron 50x5mm and 16 mm dia round stay incl nut & bolts,securing stay to wall/ roof for 75/100 mm dia pipe, complete all as specified and directed by Engr-in-charge

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (TMT)

M&L for TMT bars 5mm dia and over upto and incl 10 mm dia ,as in stirrups/ spacers ets, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, shelves and the like.

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) as in beams, cantilevers, lintel, chajja and the like, complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for finished surface complete all as specified

Provn of 25 users septic tanks including excavation and earthwork in any type of soil , PCC foundation, brick work, RCC cover slab, precast RCC man hole cover with angle iron frame vent shaft and sludge chambers complete all as shown on TD drawing, specified and directed.

M&L for construction of soakage well, internal dia 1.80M dia & depth 3.00M including excavation and earthwork in any type of soil ,brick work etc,complete all as shown on TD drawing, specified and directed.

Supply only liquid water proofing compound. Make: Fosroc/ Sika/

Taking out existing roof treatment completely upto PCC / RCC surface including removing rubbish, complete all as specified.

M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger ) (b) PCC 1:2:4,type B-O, 25 mm th in levelling layer

All as per Item No 104.00( contd/--).... (c) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface. (d) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L machine cut kota stone stab as in flooring 20-25 mm thick 580x580 mm size,pre- polished mirror finish, single colour over 15mm thick cement screed bed in CM 1:6 laid and jointed with gray cement slurry with pigment to match the shade of slab rounded exposed edges including rubbing and mirror polishing complete all as specified and directed.

M&L for machine cut Kota stone slab 18-20 mm thick, as on vertical surfaces such as riser of steps, skirting, dado etc. ,pre- polished mirror finish, single colour over & including 15mm thick rendering in CM (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, rounding of edges and polishing complete.

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 150 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for machine pressed pre-polished , rouber moulded, coloured, precast cement concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thick , M-35 grade, laid over sand filling of joints with dry sand complete all as specified. (Note- sand bed shall be measured and paid separetely).

Excavation in trenches in any type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete.

Removing excavated material (soils) to a distance n exc 50m and deposited where directed at a level n. exc 1.5M above the starting point complete.

Earth filling under floor n. exe 25 mm thick layers including spreading,levelling ,watering and well ramming complete.

M&L for Sand filling under floor or in foundation in layers including spreading,levelling ,watering and well ramming complete.

M&L for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid separately. Curing will carried out with ponding method)

S&F framed work as in doors and gate of angle and other section with gusset plate, rails, braces etc and other similar works and prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) conforming to Fe-410 W Gde E-250 quality 'A'

S&F Mild steel, plain, black sheet 1.00 mm thick in hearths ; covering to door shutters; covering to door chowkets ( frames ) ;chullah hood ; water tanks ;water troughs ; ducts; urinal troughs and funnels, etc. cut to size, edges beaded ifdirected, holes punched ; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as directed.

S & F MS work as in bands, straps, clamps, hold fasts, wind ties, fillets etc and similar small articles confirming to Fe 290. Gde E-165 complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section, in any position complete.

Dismantling timber in fillets, rails, posts, rafters, pueline, etc. under 40 sqcm in section complete.

M&L for mild steel work as in plate grider or single stanchions, built up of one beam or channel section with flange plates, caps bases. splices, angle brackets, cleats and other connections by conforming to FE 410-W (gde E-250) complete all as specified and directed.

S&F Mild steel work as in roof purlins, cleats, rails and fastenings (Pipes, Beam, Tee, Angle, Channel or Flat sections) including distance pieces, cleats etc incl cutting, welding etc confirming to Fe-410 W(gde E 250) quality B,complete all as specified and directed by Engr-in-charge .

S& F Plates, plain or chequred channels, square cut or notched (ordinary or countersunk) forming holes, with out any attachment confirming to Fe-410 W (gde 250) quality B, complete all as specified and directed by Engr-in-charge .

M&L rendering 15m thick on fair faces of brick work in CM 1:4 in single layer and finished surfaces even and smooth without using extra cement ,complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately if reqd).

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed steel juction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and making good to walls,floors etc complete all as specified and directed by Engr.-in-charge of following. Note : The wiring to be done as per IE rule and maintain colour code accordingly.

One light point / exhaust fan point/bell point ,SP, controlled by one way switch.

One ceiling fan point , controlled by one way switch through Regulaor

One three pin 5 Amp socket on same board with other switches

One three pin 5 Amp socket on independent board

All as per Item No 127.00 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S & F Switch piano flush type single pole one way 230 Volts 6 Amp complete all as directed.

S & F Switch piano flush type single pole one way 230 Volts 16 Amp complete all as directed.

S & F Socket outlet 3 pin , 230 Volts 15/16 Amps flush type multipurpose 5 pin complete.

S & F Socket outlet 3 pin , 230 Volts 5/6 Amps flush type multipurpose 5 pin complete.

S & F bell push flush type 5 Amps 230 Volts single pole complete.

S & F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts, 6 Amps 120 watts

Supply and fixing ceiling rose, three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified

S & F Lamp holder polycarbonate insulated body, with back plate with and incl LED lamp retrofit 3/5 watts complete.

S & F Lamp holder polycarbonate insulated body, with back plate with and incl LED lamp retrofit 9/10/14 watts complete.

S&F Bell Ding dong 250V AC complete all as specified & directed. Make : Havells/L&T Raaga/Anchor

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) and one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly drawing through and including 20 mm dia medium density concealled PVC conduit pipe, complete all as specified & directed. Make: Havells/Finolex/L&T

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) and one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 6 Sq mm as earth wire upto common earth and connected to earth dolly drawing through and incl 25 mm dia medium density PVC concealed conduit pipe, complete all as specified & directed. Make: Havells/Finolex/L&T

S&F energy saving Bulk head luminaire with opal diffuser with and including retrofit LED lamp 10 watts complete all as specified and directed by Engr-in-charge. Make : CG cat LBHP-10-CDL/Philips WT140W LED7S CW PSU S1 PC/Havells ENDURA RUGBYNEO N /Bajaj cat no BIBWP10WLED.

S&F wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 4000K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Wipro Cat part No LL20-281-XXX-65AL1/ Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED865SPCWH.

S&F Decorative Square/Round surface mounted LED flat panel PDC aluminium housing and PMPA diffuser makes it a robust Luminaire 12 Watts PF 0.9 and above operating voltage 150V-300V colour temp 4000K & lumen input output 70 Lumen per watt incl provisioning of 3 core white flexible multistranded copper conductor 23/0.0076 from ceiling rose to light connector complete all as specified and directed by Engineer-in-charge Make : Crompton cat part No LCDN-12-CDL/TL/WW/Wipro cat No LD80-101-XXX-60-XX/Philips Cat No DN092B LED10S-3000-PSU-WH

Supply and fixing New generation energy saving and environmental friendly long life LED Street light luminaire Endura Pearl Neo made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP66 protection and impact resistance of IK07 with separate surge protection 5KA, 40 Watts or near higher size with making all arrangement for fixing light fitting such as replacement of GI pipe bracket made of 40 mm bore medium grade pipe made to shape of 1200 of 70 cm and 50 cm to a overall length of 1.2 mtr for fixing of street light fitting including MS clamps of size 32 x 3 mm flat iron, nuts, bolts and washers of required size painting complete with all necessary electric connection etc all as specified and directed Make : Havells cat part No ENDURAPEARLNEOSL40WLED757PASYTOPC/CG Cat No LSTP-45-CDL / Philips Cat No BRP046 LED 36 CW MR S1 PSU GR /Greenstar DSS 40.

Supply, fixing , connecting and testing of 35 watt LED building security light luminaries with min 10 KV surge protector die cast alluminium housing LDR sensor for automatic operation complete suitable for and incl bracket 32 mm GI pipe bend to shape incl clamp fastner, bolts, nuts & washers of min 1.2 Mtr incl grouting etc and 3 core 1 sqmm PVC insulated cable from ceiling rose to light fitting complete all as specified Make:- Wipro cat No-LR-13-501-xx/greenstar/ equivalent in Crompton/Philips/OSRAM

Supply, fixing and Testing in repairs TPN DB VTPN 4 way 415 Volts, 50 Hz indoor type double door Sheet metal enclosure IP-43 DB's flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable managenment including mounting arrangement for DPX3 MCCB 125 Amps four pole 415 volts as incomer including connection terminal strip complete pre wired with suitable size copper conductor. The DB's should hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Engr-in-charge incl taking out Unserviceable DBs, MCCB and MCBs of any capacity, Make: Legrand/L&T/ Indo Asian.

M&L for Distribution board SPN 8 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection.Note:- DB and MCCB/MCB shall be of same make. Make:- Legrand/Hager/L&T AU/ ABB.

M&L for Distribution board SPN 6 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection.Note:- DB and MCCB/MCB shall be of same make. Make:- Legrand/Hager/L&T AU/ ABB.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 12 way IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out Unserviceable DB any capacity. complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian.

S&F MCB SP, 240 volt, 10 KA, 5-32 Amp, 'B' series confirming to IS complete all as specified and directed. Make: Legrand / L&T/ Schneider/ ABB.

S&F MCB SP , 240 Volt, 10 KA 40 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand / L&T/ Schneider/ ABB.

S&F MCB DP, 240 volt, 10 KA, 40 Amp, confirming to IS complete all as specified and directed. Make: Legrand / L&T/ Schneider/ ABB.

S&F MCB SPN , 240 Volt ,10 KA ,63 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand / L&T/ Schneider/ ABB.

S&F MCB SPN , 240 Volt ,10 KA 32 Amp 'B' series conforming to IS complete all as specified & directed. Make: Legrand / L&T/ Schneider/ ABB.

S&Fwall mounted type Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one single pole & neutral MCB 20 Amp 10 KA ,B series on DIN rail channel and suitable plug,complete all as specrified & directed Make: Legrand cat No- 5078 14 /equivalent in L&T/ Schneider.

S&F in replacement of MCCB 63 Amps four pole 415 volts thermal magnetic release ICU=100% ICS having breaking capacity 16 KA including connection terminal strip complete all as specified & directed Make:Legrand/ L&T/ Indo Asian.

Supply & fixing vibration free exhaust fan AC single phase 230/240V of size 300mm sweep double ball 900RPM with louvers making necessary fixing arrangements on wall with hold fasteners 4 Nos nut bolts connecting with three core flexible copper conductor cable (23/0.0060) from ceiling rose complete all as specified and directed. Make. Orient/ Havells/CG.

Supply & fixing ceiling fans complete with blades , 230 volts, 1200 mm sweep, white/brown/ ivery in colour, BEE 5 star rated with making necessary fixing arrangements,three core flexible copper conductor cable (23/0.0060) from ceiling rose complete all as specified and directed. Make. Orient/ Havells/Usha /CG .

Supply & Fixing vertical storage geyser of capacity 25 ltrs, having stainless steel storage tank of capacity 25 litre, rock wool insulation, thermostat, system on/ off indicator lamp, safety valve, pressure release valve, five star rating, ISI marked, including intel/out let connection with PVC connection Nylone braided PVC pipe 2 Nos suitable for hot or cold water, connected to water supply line with metal plug top , including grouting of four Nos holdfastners of suitable size for fixing the geyser and making good disturbed surface to match with existing surface all complete including water supply connections and connected to existing socket complete all as specified and directed by Engineer-in-charge. Make : Racold CDR 25 V/Crompton/AO Smith/ Orient/Jaquar.

Supply, laying & testing cable XLPE insulated armoured PVC sheathed bedded, galvanized steel strip or wire , electric power cables (heavy duty) with stranded aluminiium conductor, 1100 volts cross sectional area 16 sq. mm 2 Core all as directed incl lugs thimbles and gun metal cable glands and heat shrinkable PVC sleeves on exposed surfaces and tuflon tape duly insulated including jointing,laid in trenches/ duct,drawn through pipe across the road/ path/ along poles/ walls/ in floors/ equipments etc,complete all as specified and directed.Make- Havells/Polycab/ Grandley.

Supply, laying & testing cable XLPE insulated armoured PVC sheathed bedded, galvanized steel strip or wire , electric power cables (heavy duty) with stranded aluminiium conductor, 1100 volts cross sectional area 25 sqmm 3.5 Core all as directed incl lugs thimbles and gun metal cable glands and heat shrinkable PVC sleeves on exposed surfaces and tuflon tape duly insulated including jointing,laid in trenches/ duct,drawn through pipe across the road/ path/ along poles/ walls/ in floors/ equipments etc,complete all as specified and directed.Make- Havells/Polycab/ Grandley.

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply and laying in replacement of GI Steel tubing medium grade 50 mm dia including all fitting laying in trenches or grouting/fixing in wall for protection of cable complete all as specified and directed by Engineer-in-charge

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore, and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

Disconnecting and taking down old existing light fitting of any type & description and in any position complete all as specified & directed .

Disconnecting & taking up or down existing unserviceable sub main wiring of any description and in any position including conduits/ battens etc, complete all as specified and directed.

Disconnecting and taking up or down existing unserviceable MCB, DB of any description and in any position with existing fittings and making good disturb surface match the existing complete all as specified and directed.

Taking up or down steel tubing and connection of 50mm bore of any description and any position complete all as specified as directed.

M/S JAI PRAKASH GOEL

M/s Anil Kumar