Special repair of MIG House A-18 in Officer Colony at Narnaul in Mohindergarh District. (Re-invited)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing(HSR 8.5 b)

Reinforced cement concrete with cleaning and straightening and cutting of bars if required (HSR 8.6 e)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled(HSR 8.18) (i) door

ii) Vantilator

iii) Window

Dismantling cement conglemerate / terrazzo floors 25 mm to 50 mm thick including concrete base(HSR 8.25)

Scraping of Cement Plaster (HSR 8.32 c)

12 mm thick cement plaster 1:6 (HSR 15.7)

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction, including disposal of all surplus soil as directed within a lead of 30 Mtrs. (HSR 6.6)

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.38)

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)].

First class brickwork laid in cement sand mortar 1:6 in foundation and plinth. (HSR 11.2)

Cement Concrete 1:8:16 with brick ballast 40mm nominal size in first storey upto 4 meters above plinth level. (HSR 10.44)

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR 14.10)

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete(HSR 18.34 b) a) door and window frame of size 89 mm X 50 mm with 40 mm wide single rebate

d) door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate

c) door and window frame size 127 mm X 50 mm with 40 mm wide double rebate

Base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. (HSR 14.89) Note: - Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK.

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in skirting/dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. (HSR 14.90) Note: - Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK.

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects (a) extra over Item Nos. 10.79 to 10.94, if 1:1 ½:3 mix is used, instead of 1:2:4 (HSR 10.82+10.95a)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including Straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths /storeys/ basements etc. (Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing, shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement). (HSR 18.22).

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR 11.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall(HSR 15.12)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand (HSR 13.13)

Cement concrete 1:2:4 gola 10cm X 10cm quadrant along junction of roof with parapet wall finished smooth, where specially specified(HSR 13.64)

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50)

Bottom khurra on ground 1:2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3(HSR 13.57)

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work(HSR 16.58)

Applying pink primer or aluminium priming ocat on wood work including preparation of surface, Knotting and stopping etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade(HSR 16.3)

Providing and Applying Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hot- pressesd,conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sid (HSR 17.93) 35 mm - Note

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ,chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges,screws,chocks/cleats,stops,nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position).(HSR 17.90)a - Note

Earth work non plastic or Tibba Sand under floors taken from outside of campus area with all lead and lift including loading, unloading, laid in 15 cm layer including ramming, watering, consolidating, compaction, and compensation of earth etc., complete in all respect as per the direction of engineer in charge. [NS].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- (HSR 30.5 A i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM G.C.I.’P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2 a i)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75 a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE C.P. BRASS WALL MIXER 15 MM (HSR 30.81 a)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineer- in-charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC.(HSR 30.41 white v)

PROVIDING AND FIXING IN POSITION BEST QUALITY STAINLESS STELL DRAINING BOARD WITH IRON BRACKETS FOR BUILDING into wall INCLUDING PAINTING, CUTTING AND MAKING GOOD THE WALLS ETC(HSR 30.58)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE SHOWER WITH 15 OR 20 I/D IN-LET(HSR 30.66 b i)

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS: 12701 on roof top of buildings includig cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction of Engineer-in-Charge.(HSR 30.119) 500 ltr capacity

Supply and erection of polypropylene random (PP-R) hot water pipe as per IS-15801 (HSR 30.122) (i) 20mm

Cost of aluminium fittings complete for doors and windows, such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) (HSR 17.72) a

ii) for double leaf shutter

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90]. (a) 100 mm dia PVC Bend.

Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84). (b) 75 mm internal diameter.

(a) 100 mm internal diameter.

Constructing brick masonry inspection chamber sizes as given below upto 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent limer mortar 2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2;4 slab 100 mm thick./C.C. topping 50 mm thick with 455 mm x 455 mm 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint coplete as per standard design. [HSR 29.84]. (b) Size 450 mm x 450 mm

Extra for over 0.30 metre depth of inspection chamber. (a) 450 x 450 mm. (HSR 29.85)

Providing and fixing SFRC manhole covers and frames markd with IS: 12592 including setting the same to correct lines and levels in 1:2 cement sand mortar over manhole including carriage loading, unloading stacking, handling, re-handling etc. complete in all respect to the satisfaction of engineer-in-charge. Type: Extra heavy duty set (MD-10) 560 mm clear opening. (HSR 29.94)

Wrought iron and mild steel (using angles, flats square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12).

Cement pointing 1:2 flush on brick and tile walls. (HSR 15.62)

Recovery Items:- Bidders have to quote rates for recovery items at least or more than reserve price. The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Note: - The reserve amount is minimum amount to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price as under:- The quantities are as under:- i) Quantity of Good Bricks @ Rs. 4.50/- Each

ii) Quantity of Brick Bats @ Rs. 400/- Cum

iii) Doors @ 300/- each

iv) Ventilators @ 100/- each

v) Windows @ 150/- each