REPAIR MAINTENANCE OF 20 NOS ORs TOILET BATHROOM EACH AT OLD 160 BN HQ NOW 84 HQ BN CHATHA CAMP

12 mm cement plaster of mix 1”4 (1 cement: 4 fine sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colors White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coars sand), joining with grey cement slurry @ 3.3 kg/sqm including grunting the joints with white cement and matching pigments etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in charge, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Distempering with oil bound washable distemper or approved brand and manufacture to give and even shade: New Work (two or more coats) over and including water thinnable priming coat with cement primer

providing and fixing G.I pipes complete with G.I fittings and clamps, i/c cutting and making good the wall etc. 15 mm dia nominal bore

Providing and fixing C.P brass long body bibcock 15 mm

Providing and fixing water closet squatting pan indian type W.C pan with 100 mm sand cast iron P or S trap, 10 litter low level white PVC flushing cistern, including flush pipe with manually controlled device (handle liver) with all fitting s and fixtures complete including cutting and making good the walls and floors whenever required. White Vitreous china Orissa pattern W.C pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I Brackets, 15 mm C.P brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap.

Providing and fixing C.P brass shower rose with 15 or 20 mm inlet: 100 mm diameter

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing U-PVC pipes (working pressure 4 kg/CM2) Single socketed pipe 110 mm dia metre

SUSHIL KUMAR (BID ID -3176024)

Item code 2

Item code 4

Item code 5

Item code 6

Item code 8

Item code 13

SUSHIL KUMAR

Item code 7

Item code 9

Item code 10

Item code 11

Item code 12

Item code 13

Item code 14

Item code 15