PROVN OF DEFI TWO TOILET BLOCK AND BATHROOM BLOCK WITH INTERLOCKING FOOTHPATH NEAR BLDG NO T-20 OF FD REGT AND CERTAIN SANCTIONED WORKS UNDER AGE B/R-II OF GE SATWARI

Amount

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n. exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed.

Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed .

M&L for plain cement concrete 1:4:8, type D2 (using 40mm graded crushed stone aggregates) as in foundation, filling & mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-20 (design mix) (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for reinforced cement concrete M-20 (design mix) (using 20 mm graded crushed stone aggregates) as in column,pillars, piers and struts complete all as specified and directed.

M&L for reinforced cement concrete M-20 (Design mix), (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies complete all as specified and directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified and directed .

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups , spacers and binders including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan exceeding 6m mean radius , built in cement mortar 1:6 complete all as specified and directed

All as per Ser item No 14 here-in-before but except brick complete all as specified and directed.

M&L for brick work with old size sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed .

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on brick work or concrete surface,surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for sand filling under floor with washed and screened dry fine river sand including watering, well ramming and consolidation complete all as specified and directed

M&L for preparation of new plastered surfaces of walls, & applying two coats of oil bound distemper over two coat of wall care putty of 1-2 mm thick each and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of weather proof acrylic emulsion paint over a coat of weather proof exterior wall care putty 1 to 2 mm thick and one coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for hard core of gauge not exceeding 63mm using broken stone or boulders, deposited, spread and leveled in layers not exc 15cm thick, watered and rolled/rammed to a true surfaces complete all as specified and directed .

M&L for 25 mm thick plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregates) as in sub base/ levelling course of floors, finished even and fair complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 , type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. surfaces finished even and fair including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:2 complete all as specified and directed .

M&L for plain cement concrete 1:2:4 ,type B1(using 20mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, window or door cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings,side posts of precast jallies etc. including slightly rounded or chamfered angles including necessary formwork complete all as specified and directed.

M&L for 7 to 8mm thick non skid coloured digital ceramic joint less tiles (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and poined in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement motar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured digital tiles,300x450x7 mm thick, as in vertical surfaces, set and jointed in neat cement slurry and pointed in white or colored cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for granite work (Z-black) 16 to 18 mm thick any colour (table rubbed and polished) in steps, jambs , pillars, window cills , cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F pressed steel frames of size 105mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

M&L for 35mm thick flush shutters, solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

M&L for preparation of new or previously untreated wood or wooden based surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Vitreous china urinal of size 375x390x590mm, white including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and chromium plated spreader including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 110 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F UPVC (SWR) type B pipes, 75 mm bore, single socketed, in any length with rubber ring joints fixed to walls with nail at spacing of 1m center to center including stack clamp of GI flat 30mm wide 2mm thick complete all as specified and directed.

S&F UPVC (SWR) bends any radius, 75 mm bore complete all as specified and directed

S&F UPVC (SWR) bends with access door any radius, 75 mm bore complete all as specified and directed

S&F UPVC (SWR) bends any radius, 110 mm bore complete all as specified and directed

S&F UPVC (SWR) bends with access door any radius,110 mm bore complete all as specified and directed

S&F UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

S&F vitreous china squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rest, cast iron 'P' or 'S' trap of size 100mm, including provision of plain cement concrete bedding and connection to trap and to flushing pipe, anti syphonage pipe etc and making good the floors complete all a specified and directed

S&F vitreous china wash down water closet pan (pedestal pattern) of size 565x360x395mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

M&L for reinforced concrete pipes class NP-2 laid and jointed complete with collar of size 150mm (internal dia) complete all as specified and directed.

S&F vitreous china table top wash basin, of size 600x480x150mm, rectangular shape , white, to be fixed on counter/ RCC slab including chromium plated waste coupling, 32mm waste pipe complete all as specified & directed

S&F single lever basin mixer without popup waste with 450mm long braided hose, fancy type complete all as specified and directed.

S&F brass chromium plated tubular towel rail 20mm dia, D type , 600 mm long between flanges fixed with CP brass screws including wooden/plastic beads complete all as specified and directed.

S&F sheet glass shelf assembly consisiting of 5.5 mm thick sheet glass, shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F corner glass shelf of size 30 cm with Chromium plated bracket guard and railing fixed with and including screws and wooden/plastic cleats complete all as specified and directed .

S&F Chromium plated soap dish of size 160x160x90mm, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F bib tap with flange,chromium plated, fancy type, cast copper alloy ,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F angular stop cock with wall flange , cast copper alloy, chromium plated screwed with wall flange suitable for 15 mm iron pipe, complete all as specified and directed.

S&F cast copper alloy, chromium plated, wall mixer non telephonic shower arrangement with connecting legs & wall flanges complete all as specified and directed.

S&F brass chromium plated shower rose 125 mm of dia with arm and with or without swivel joints to steel pipe or union complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed.

S&F Galvanised steel tubing, 15mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F Galvanised steel tubing, 20mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and directed.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to distributed surface of walls complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick ( style ) consisting of frame work made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour P.V.C‘ C’ channel having a PVC sheet strip 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap inserts for top rail; and bottom rail paneling of plain, colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rail with suitable PVC sheets beading and jointed together with solvent cement S&F in frame at site as per specification complete all as specified and directed.

S&F aluminium anodised barrel tower bolts, 150mm long of extruded section, fixed to doors with screws complete all as specified and directed.

S&F 100mm long mild steel butt hinges, medium weight ,fixed with screws complete all as specified and directed

S&F aluminium anodised , fabricated type handle 100mm size complete all as spcified and directed.

S&F aluminum alloy, anodised, sliding door bolt of length 250mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminum alloy and fixed complete all as specified and directed.

S&F aluminum powder coated (coating not less than 50 micron) window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary glazing and locking arrangements anodised aluminium fittings such as peg stays 150mm long (1 No.). 100mm long hinges type B-21(2 Nos.) suitable handle (1 No.) complete all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:4 on concrete surfaces of roof finished even and fair including mixing of water proofing compound as per manufacturer's instructions complete all as specified and directed. Note : Water proofing compound shall be measured and paid separately as supply only.

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer confirming to IS-3384 @ 0.4 Kg/sqm .Cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.0 Kg/sqm with 160 Grams/sqm non woven polyster made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed (d) Complete treatment to be carried out by authorised applicator of waterproofing manufacturer.

M&L for applying two coats of aluminum paint over the APP membrane complete all as specified and directed.

Supply only liquid water proofing compound

M&L for factory made box type steel windows/ventilators, double shutter,outer frame made out ERW TUBE 'P section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) openable shutters side hung including pintle hinges with two nos MS tower bolts 150mm size on each shutter, steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required steel windows will be double shutter (external glazed and internal wire gauzed) complete all as specified in Drg No CEPZ/TD-324/07 of sheet No 1/3 to 3/3 complete all as specified and directed. Note: - The quoted rate shall be deemed to include :- (i) 04 Nos MS steel lugs of MS flat 20 x 5mm & 20 cm long over all welded to frames (ii) PCC block for embedding lugs.

S&F Mild Steel framed work such as grills, gratings etc. with ends of bars shoulderd and/or riveted, or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks,cooler stand,ladder and similar work conforming to Fe290, Gde-E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for Chequered cement concrete tiles 30cmx30cmx25mm thick, with grey cement and pigment, set ,jointed and pointed in neat cement slurry as in floors, laid over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed

Dismantling of timber scantlings 40 Sqcm and over in section, framed work,in any position complete all as specified and directed

Dismantling of timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section,unframed work complete all as specified and directed

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries rails and fastening and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces, cleats etc confirmimg to Fe 290 (Gde E -165) complete all as specified and directed .

Dismantiling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed

S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed .

S&F Pre painted galvalume aluminium zinc coating (AZ-150 micron) GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed .

Dismantling Wall and ceiling boards (fibre,pulp, insulation) or insulation boards/slabs/ blankets, any thickness, including cover fillets etc complete all as specified & directed.

S&F GI snap grid frame work (Grid size 605mm x 605mm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm ,ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid complete all as specified and directed ..

Demolition of brick work or stone/boulder masonry , built in cement mortar or cement lime mortar including all quoins, arches & pillars etc of any description and in any position and removing unserviceable material from work site to outside defence premises complete all as specified and directed

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubing down with water etc and removing unserviceable material outside defence land complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed

M&L for complete removal of existing treatment on wall surfaces, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over one coat of wall care putty 1 mm thick and one coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of weather proof acrylic emulsion paint over a coat of weather proof exterior wall care putty 1 to 2 mm thick and one coat of primer complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n. exc 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 sqm & n. exc 4 sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site complete all as specified and directed.

S&F pressed steel frames of size 125mm x 60 mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including mild steel hinges, 100 mm long , medium weright and 25 mm x 3 mm flat iron as in hold fast , tie bar including necessary fixing lugs, lock strike plate and fixing arrangement and making good the disturbed surfaces in cement mortar 1:3 or cement concete 1:2:4 type B-1 including PCC 1:3:6 type C1 as in back fill to chowkats complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood , glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers size of members of shutters as specified in SSR Part-I Section-8 clause 8.24 (a) fitted to chowkats complete all as specified and directed.

M&L for 4 mm thick, plain sheet glass, ordinary quality and glazing with glazing pins, oil putty or with any type of beads in squares n. exc 0.5 sqm each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth , 0.56 mm normal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F aluminium hanging floor door stopper,twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws complete all as specified and directed.

Demolition of cement concrete (un-reinforced) ground floor to 2nd floor and pavings n exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site to out side defence premises complete all as specified and directed

M&L for 75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base, finishing surfaces even and fair complete all as specified and directed.

M&L for providing and laying 60 mm thick factory made charmfered edge cement concrete paver block of M-35 grade of approved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic parking etc of required strength , thickness & size/ shape made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo dado from wall surface including cement mortar bedding, (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specied and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors,apron etc laid dry or pointed in any mortar complete all as specified and directed.

M&L for 8 to 9 mm thick vitrified ceramic coloured edge cut, joint free tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed .

M&L for 8 to 9 mm thick vitrified ceramic coloured , edge cut, joint free tiles (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm ,in vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed ..

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed

S&F machine cut kota stone slab in flooring, treads of steps, 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing cutting and mirror polishing over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting , dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, cutting and mirror polishing over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) of size 565x360x395mm white in colour including connection pipe to union of flushing cistern, inlet and overflow pipes, connecting only to flushing cistern, anti-syphonage pipe with PVC flush pipe of 32mm dia including plastic seat with cover, white in colour with mild steel chromium plated hinging and 'P' or 'S' trap device complete all as specified and directed

S&F in repair 10 litres PVC, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float 32mm PVC 'L' bend and handle including brackets complete all as specified and directed

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connectios and fixed in position complete all as specified and directed.

S&F in repair brass chromimium plated sink mixer swan neck with swinging spout (wall mounted model) with connecting Legs & wall flanges complete all as specified and directed. . .

S&F in repair brass chromium plated sink cock with swinging spout (wall mounted model) with wall flanges complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) with plastic lid cover, hoisted and fixed in position including PTMT Ball valves high pressure with epoxy coated aluminum rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe including making connections complete all as specified and directed.

S&F in repair chromium plated spreader for urinal complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including cast iron brackets, brass chromium plated waste coupling 32mm bore, waste pipe PVC 32mm bore complete all as specified and directed

S&F in repair pillar taps, chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repair sinks , made of 1.0mm thick stainless steel,overall size of sink 610mm x 460mm with bowl size 560mm x 410mm x 200mm, plugs, washers, waste pipe, union, chromium plated waste coupling and cantilever brackets embedded in cement and sand mortar in wall complete all as specified and directed

S&F in repair plate rack made of 1.0mm thick stainless steel of size 39"x30"x10" fixed with steel fastners or steel screws complete all as specified and directed

S&F factory made 18 mm thick (+0.7mm) celuka PVC ply of density 600 kg/cbm . One side prelam and other side plain 18mm thick celuka PVC ply for kitchen cabinet shutter/ shelf/ partitions/drawer complete all as specified and directed ..

M&L for plain 18mm (+0.7mm) thick celuka matt finish PVC foam ply of density 600Kg/cbm, for kitchen cabinet shutter/Wardrobe complete all as specified directed .

S&F in repair continuous (piano) hinges,width of flaps (when open) 30 mm, heavy duty, mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified and directed.

S&F steel fastners of size 75mm long drilled and fixed to walls complete all as specified and as directed.

S&F steel support of 50mm dia and 75mm length fixed with bolts at bottom of cupboard box complete all as specified and directed.

S&F stainless steel designer handle ( heavy type) 100 mm size, fixed in drawers or shutters of cupboards complete all as specified and directed.

S&F Galvanised steel tubing, 25mm bore, medium grade with all fittings, fixed to wall with clamps /ceiling or laid in floors complete all as specified and directed

S&F in repair bib tap with flange,chromium plated, fancy type, cast copper alloy ,screwed down, screwed for 15 mm bore of iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair angular stop cock with wall flange , cast copper alloy, chromium plated screwed with wall flange sutable for 15 mm iron pipe, complete all as specified and directed.

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends complete all as specified and directed.

S&F in repair UPVC (SWR) floor trap plain with grating having diameter of outlet 75 mm including jointing with solvent cement to waste pipe, laid in cement concrete 1:2:4 type B-1 complete all as specified and directed.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings and removing from site complete all as specified and directed

Complete removal of existing water proofing treatment of any description including under layer, taking down cement plaster any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in padding over roof, finished & laid to required slope complete all as specified and directed .

Demolition of reinforced cement concrete ground floor to 4th floor and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site to out side defence premises complete all as specified and directed

Taking down carefully existing aluminium/copper point wiring for light, fan, socket or power bell complete with fittings such as Switches, sockets, ceiling roses, holders, call bells etc & making good the disturbed surfaces of walls/ceiling, matching the colour with existing surface complete all as specified and directed. Note : Rate for making good shall be deemed to be included in above item rate

Taking down of unserviceable MCB DB, SPN /TPN along with MCB's complete all as specified and directed.

Taking down of unserviceable sub main wiring of any size complete all as specified and directed.

Point wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable(ISI marked) 1100 volts grade FRLSH with multistranded copper conductor, drawn through concealed / surface in wall / roof/ceiling surface and its accessories on the surface etc including PVC rigid concealed conduit of suitable size with all accessories such as bend, reducers, MS hooks including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc including continuous earth wire of size 1.5 Sqmm PVC FRLSH stranded copper conductor unsheathed, insulated, stranded connected to common earth point dolly for one light point/fan point/call bell point, 230 volts controlled by one switch complete all as specified and directed . Note:- Proper colour coding is to be followed as per IS specifications.

All as per Srl item No 140 here-in-before but for one socket outlet, 3 Pin 5 Amps, 230 Volts on independent board complete all as specified and directed

All as per Srl item No.140 here-in-before but for one three pin socket outlet 5 Amp on the same board with other switches complete all as specified and directed

All as per Srl item No 140 here-in-before but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire complete all as specified and directed

S&F modular type switch, one way 6 Amps,1 module complete all as specified and directed

S&F modular type socket 3 pin, 6 Amps, 2 module complete all as specified and directed .

S&F modular type switch, one way 16 Amps, 1 module complete all as specified and directed .

S&F modular type socket 3 pin, 6 A/16 Amps 2 module complete all as specified and directed .

S&F modular type fan regulator step down 120 watt, 2 module complete all as specified and directed .

S&F ceiling rose, surface backelite, two/three terminal, 240 volts complete all as specified and directed .

S&F LED light fitting 1 x 18Watt, 220V, Integrated batten type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all fixing arrengenment complete all as specified and directed.

S&F energy saving new generation 10W LED bulk head luminaire with opal diffuser, IP 65 and including connecting up with twin core twisted flexible copper coductor cable with suitable size of 230 volt,50 Hz complete all as specified and directed.

S&F Sheet metal enclosure for DBs,SPN, double door,IP-43 protected, 230 Volts,8 ways with 100 amps rated copper bus bar complete all as specified and directed

S&F MCB SPN, 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specified and directed . .

S&F factory made epoxy polyester powder coated distribution board TP&N ,4 ways (VTPN DB), double door,(concealed flush to wall) (IP-43 protection) fabricated from minimum 1.2 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 250 Amps bus bar, neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with space for provision for 4 pole MCCB as incommer and outgoing MCBs as required at site and conforming to IS: 8623 along with cable end box including making good disturbed surface complete all as specified and directed. NOTE: (a) MCCBs and MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of BoQ..

S&F MCB Single pole, 6 to 32 Amp, 240 Volts with rupturing capacity 10 KA, 'C' series, complete all as specified and directed .

S&F MCB TPN, 40-63 Amp, 415 Volts with rupturing capacity 10 KA, 'C' series, complete all as specified and directed .

S&F Submain wiring with two runs of single core PVC FRLSH unsheathed, insulated, copper cable of 4 Sqmm size, multi stranded, 1100 volts grade with PVC insulated,unsheathed FRLSH copper wire 4 Sqmm for continous earth wire drawn into and including concealed PVC conduit of suitable size complete all as specified and directed . Note :- Two runs of 4 Sqmm copper cable and one run of 4 sqmm copper wire earth continuty conductor in conduit with accessories shall be measured as one length)

Taking down existing ceiling fan of any size/sweep including oiling, greasing, cleaning and applying two coats of synthetic enamel paint after preparation of surface and refixing the same complete all as specified and directed .

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC 1:2:4 type B-1, precast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh ,15mm dia light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specifieds and directed ..

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 16 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and directed.

M&L for sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

M&L for factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, laid flat and dry in trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed.

S&F Galvanised steeI tubing, light grade, 40mm bore, for cable protection, fixed to pole/wall with MS clamps, nuts, bolts etc or laid under floor/road/pavement complete all as specified and directed.

S&F exhaust fan, steel body, AC single phase. 230 V of size 300 mm sweep with, blades and frame and louvers, hanging on wall with 4 Nos steel fasterners 10mm dia & 100mm long including wall hole and making good the disturbed surfaces as per existing complete all as specified & directed

S&F electric water heater of capacity 25 litres,BEE 5 Star rated,storage type, steel body vertical type with glass lined /porcelain enamel coated steel inner tank and glass line double ceramic heating element upto 2 KW complete with all accessories such as safety valve,thermostate NRV,connection piece etc and fixing with 04 Nos nut bolt grouting in wall in PCC(1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and directed

S&F Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 25 mm bore pipe, including making connections complete all as specified and directed.

M&L for cutting existing cast iron/GI pipe in position for insertion of CI specials or GI fittings viz Tee, collar, bend or tail piece etc for 80 to 200 mm bore pipe including removing of blockage, cleaning of pipe line complete all as specified and directed

S&F LED luminaire 600 mm x 600mm, 35/36 watt, 220 V,AC, Recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F Sheet metal enclosure for DBs,SPN, single door,IP-43 protected, 230 Volts,2 ways complete all as specified and directed

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 35 Sqmm, 3.5 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, including taking down existing one complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable, cross sectional area 25 Sqmm, 2 core, aluminum conductor, 1100 volts grade under ground cable including both side connection with lugs/thimbles of suitable size etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, including taking down existing one complete all as specified and directed.

M/S SHAKTI STEEL INDUSTRIES (BID ID -3399478)

J P TECHNO (BID ID -3398767)

M/S Raman Construction Co. (BID ID -3398969)