Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹6.7 LAccepted-AOC | ₹6.7 L | L1 | Accepted-AOC lowest rate quoted by the tenderer hence the tender is accepted |
| 2 | L2₹6.9 LRejected-AOC | ₹6.9 L | L2 | Rejected-AOC higher rate quoted compared to lowest tenderer quoted rate |
Tender Value
Refer Docs
EMD Value
₹6,750
Closing Date
3 Mar 2026, 3:00 pmClosed
Executive Engineer
Executive Engineer Buildings C and M South Presidency Division Chepauk Chennai 5
Special repairs to damaged roof water supply arrangements and other repair works of NHIS Director General Audit room at 6th floor in Commissionerate of Treasuries and Accounts Office Perasiriyar K.Anbhazagan Maligai Nandhanam Chennai 35
2026_PWD_669103_1
TNPWD/58-03/40M/2025-2026
Open Tender
Civil Works
60 days
Nandhanam chennai
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹6,750
15 May 2026
2 Mar 2026
3 Mar 2026
2 Mar 2026
3 Mar 2026
2 Mar 2026
Dismantling, removing and carefully stacking RCC by manual / by using deploying machinery etc., complete complying with standard specification and as directed by the departmental officers at site of work.
Labour charges for Removing the Aluminium partitions and Refixing the same in position without any damage and redoing the plastered portion including lifting charges, Conveyance charges etc., complete complying with standard specification and as directed by the departmental officers at site of work.
Removing all Lossen particles in the concrete and dead mortars. Cleaning the corroded rods with metal brush and sand paper followed by application of rust removal allowing it for temp cure providing anti corrosive coating for the existing rods with zinc rich primer / Epoxy after completion of anti corrosive works based on the structural requriment providing new rods by anchoring by executing lockfits/polyster/vinylestser epoxy grouters. After completion of rebar works applying complete bonding agent for the old reinforcement rods/new reinforcement rods and the concrete areas. Bonding agent-Epoxy SBR, Supplying and appilication of microconcrete 20mm to 25mm in the concrete areas, Allowing two days curing period. finally, Finishing with OPC cement, river fine M-Sand, Mixing with SBR latex curing for 5days.
Repairing damaged Terrace tile area & Wall surface with waterproofing elastomeric coat by removing all existing paint, putty and Loose plaster over wall, clean surface preparation with metal brush & putty blade also complete touch up work with pop mixing with SBR Chemical. For walls & Terrace with SBR (Styrene Butadiene Rubber) / Acrylic primer added to the cement with 1:1.5 ratio apply one coats as a protection coating & to make the surface strong. Followed by two coat of elastomeric water proofing coating. The rate including labour charges, SBR/ Acrylic primer, Elastomeric, POP and scaffolding etc., complete complying with standard specification and as directed by the departmental Officers at site of work.
Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
Supplying and fixing in position white / colour glazed (European Water Closet of Size(665 x350 x 705mm) Special type Zest Model- C8810 (S-110) best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.
Renewing the damaged broken unserviceable Health faucet with new one of CP Two way bib cock tap with health faucet 15mm dia of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers.
Renewing the damaged broken unserviceable Swan neck tap with new one of SS Swan neck tap 15mm dia of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers.
Renewing the damaged broken unserviceable Angle cock with new one of CP Angle cock 15mm dia of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers.
Renewing the damaged broken unserviceable 2 way Angle cock with new one of 2 way Angle cock 15mm dia of approved quality and make including labour charges for fixing in position etc complete complying with standard specification and as directed by the departmental officers.
Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).
Supplying and fixing best approved quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).
Renewing and refixing the old damaged flushing tank with new one of 10 litres capacity flushing tank of approved quality and make and labour charges for fixingetc., complete and as directed by the departmental officers.
Providing and Fixing mirror shutter to Cupboard made with approved commercial plywood frame, mirror shall be 8mm thick plain float glass mirror,best quality with required screws as specified including labour charge for fixing inposition etc., complete complying with standard specification.
Renewing the damaged door closer with new one door closer ISI mark Hydraulic door closer of sizes of approved quality using Aluminium Extruded section Body Tubular Type Universal Hydraulic Door closer with Doible speed Adjustment like HARDWYN (make) GAZEL (Or) Equivalent (With ISI Monogram) brand inclusing labour charge for fixing inposition etc.,
Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including mortar plasticizer at 200ml per 50Kg of cement used, finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.
Plastering the surface of walls with Cement Mortar 1:5 (One cement and Five plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used , curing etc., complete complying with standard specification and as directed by the departmental officers.
Painting Old Plastered Wall Surface with Two finishing coats of ready mixed Interior (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
Supplying and fixing Armstrong false ceiling arrangements with aluminium anodized "T" section and "L" angle frame work, grid of size 60x60cm with aluminium "T" section 25x25x2.8mm "L" angle of size 25x25x2mm thick and the same is supported at suitable intervals by adjustable type 6mm dia M.S. rod with suitable threaded nuts suspended rods hung from ceiling at 120cm, centre to centre in logitudinal section and60cm at middle portion.60x60cm panels should be covered with 10mm thick Amstrong in the grid so as to give a seat to false ceiling including painting the 6mm dia MS rods etc., complete complying with standard specifications. Necessary openings and arrangements for fixing electrical fittings should be provided with suitable frame work etc., complete.
Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. - Internal water supply above ground level.50mm dia
Renewing and refixing PVC special of approved quality and make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.
Elbow 50mm dia
Coupling 50mm dia
Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.
Supplying and fixing approved best quality of Oven Stand make including labour for fixing in position etc complete complying with standard specification and as directed by the departmental officers at site of work.
Providing and Writing Name and Designation on approved Name board using synthetic Enamel Paint of approved colour etc., complete complying with standard specification and as directed by the departmental officers at site of work.
Clearing the floor using Soap oil thoroughly removed the patches and as directed by the departmental officers
Collecting the scattered debries using tipper machinery from work spot and loading into the tipper lorry and conveying away the same to outside by lorry to a lead of 3km entirely with in city limit including loading and unloading charges and dumping in low places and levelling neatly etc., complete complying with standard specification and as directed by the departmental officers. (200 cft volume capacity)
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.42 MB
BOQ_803984.xls
BOQ • 0.32 MB
CONDITION03.pdf
Tender Documents • 0.47 MB
Download all tender documents and submit your bid