REPAIR/REPLACEMENT OF VERTICAL PUMPS/SUBMERSIBLE PUMPS/CENTRIFUGAL PUMPS/STARTER PANEL/ LT PANEL BOARD, CI/DI PIPE AND OTHER CONNECTED ITEMS AT GUNJKHEDA, CMPH, PICKET HILL, MAP PUMP HOUSE, PERIMETER AREA AND DEPOT AREA UNDER GE PULGAON

Amount

Disconnection and removing the 60 HP VT pumpset along with section, delivery pipe line,column pipe, control valves,shafts & shafts coupling etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as directed. Note:- Unserviceable parts will be measured and paid separately under respective items of sch 'A' lubricating oil, Greasing, overhauling and packing kit of pump set including in the unit rate.

All as per item No 1 above but 40 HP.

Material & labour rewinding of 60 HP VT electric motor with super enamelled winding wire of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tape, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporate and achieving proper insulation results and reassemble the motor including replacement of terminal plate and taking out old winding complete all as directed

Supply only spares parts suitable for 60 HP VT pump set:-

Trans Bearing

Shaft Sleeve Part No 312

Shaft Sleeve Part No 311.2

Bowl Bearing

Bearings suitable to the pump set(No 51220)

Bearings suitable to the pump set(No 6220)

Bearings suitable to the pump set(No 6311)

All as per item No 3 above but 40 HP.

Supply only for spares parts suitable for 40 HP VT pump set:-

Trans Bearing

Shaft Sleeve Part No 312

Shaft Sleeve Part No 311.2

Bowl Bearing

Bearings suitable to the pump set(Upper) 7316

Bearings suitable to the pump set(Below) 6211

Material and labour for spray painting of the pump set of capacity 60HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Material and labour for spray painting of the pump set of capacity 40 HP delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of colour as approved by GE.

Taking out defective submersible (vertical) pump set of capacity 60 HP from jack well for repair by lifting GI tubing of size 150mm to 200 mm GI/CI/MS pipe from upto 80 to 120 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pully block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and ovhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset with motor with one coat of synthetic enamel paint after cleaning and scrupping and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed by Engr-in-Charge. Note :- (i) The rate quoted for this item shall includes labour charge only for maint repair and replacement of defective/UNSV spares/accessories. Spares are to measured and paid separately under subsequent respective items. (ii) Cost of other minor items/ spares such as nut, bolts, washer, gaskets,paints etc which are not covered under Sch 'A' but required for efffective functioning of the plant shall be deemed to included in this items.

All as per item No 9 above but 50HP

All as per item No 9 above but 40HP

All as per item No 9 above but 30 HP

Supply only the following items/parts for 60 HP Submersible vertical type pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Three core 16 sqmm submersible copper cable for connection

Supply only the following items/parts for 50 HP submersible Jack well pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Three core 16 sqmm copper cable for connection

Supply only the following items/parts for 40 HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Three core 16 sqmm copper cable for connection

Supply only the following items/parts for 30 HP submersible Jack well pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

Three core 16 sqmm copper cable for connection

Dismantling the motor of submersible (vertical type) pumpset of capacity 60 HP, removing the existing burnt out winding and re-winding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, three phase, 415Volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as directed.

All as per item No 17 above but 50HP

All as per item No 17 above but 40HP

All as per item No 17 above but 30HP

M&L for fixing in replacement of CI non return valve heavy duty both end flanged incl making flanged joint, rubber gasket, nuts & bolts washers sizes 200 mm complete allas specified and directed. Make:Kirloskar/Upadhayaya/Leader

All as per item No 21 above here-in-above but 150 mm dia.

All as per item No 21 above here-in-above but 100 mm dia.

M&L for fixing in replacement of CI air release valve heavy duty single end flanged incl making flanged joint, rubber gasket, nuts & bolts washers sizes 100 mm complete allas specified and directed. Make:Kirloskar/Upadhayaya/Aarko

S&F in replacement of MS pipe 200 mm dia ligth grade A class both end flanged including making flanged joint, rubber gasket, nuts & bolts washers,nut and bolts complete all as specified and as directed.

All as per item No 25 above here-in-above but 150 mm dia.

All as per item No 25 above here-in-above but 100 mm dia.

S & F repairs MCCB 3 pole, 250 Amp,36kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as directed

S & F repairs MCCB 3 Pole 160Amp, 36kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as directed

S & F repairs MCCB 3 Pole 100Amp, 16kA, 415V AC, 50 Hz in to the existing panel board with new one of same size and capacity complete all as directed

S& F repairs MCCB 3 pole, 200Amp, 415V ,36 kA,load line type with thermal setting in to the existing panel board with new one of same size and capacity complete

S& F in repairs MCCB 4 pole, 200Amp, 415V ,36 kA,load line type with thermal setting in to the existing panel board with new one of same size and capacity complete all as directed.

Supply & fix in replacement power contactor MNX-185, 3 Pole, 415 V, Current rating 70 A - 110 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed. Make : L&T/Havels/CG.

Supply & fix in replacement power contactor MNX-80, 3 Pole, 415 V, Current rating 80 A, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed by Engineer-in-Charge.

Supply & fix in replacement power contactor ML-6, 3 Pole, 415 V, Current rating 110 Amps, 2NO + 2NC having coil voltage 240 Volts including taking down the U/S power contractor all as directed by Engineer-in-Charge.

Supply & fix in replacement spare parts kit for 3 pole 70Amps, 415 volts, with coil rating 230/415 volts, type ML-4.

Supply & fix in replacement spare parts kit for 3 pole MNX 140 including taking down the U/S power contractor all as directed.

Supply & fix in replacement spare parts kit for 3 pole 110Amps, 415 volts, with coil rating 230/415 volts, type ML-6. make L&T/Havels/CG.

S&F Bimetalic Overload relays suitable for Power Contactor 40-70Amps, 415 volts, with coil rating 230/415 volts complete all as directed type ML-3.

S&F Bimetalic Overload relays suitable for Power Contactor 70-110 Amps, 415 volts, with coil rating 230/415 volts complete of all as directed

S&F Bimetalic Overload relays suitable for Power Contactor 110Amps, 415 volts, with coil rating 230/440 volts complete of all as directed

Supply & fix in replacement in repairs spare parts kit for 3 pole 80Amps, 415 volts, with coil rating 230/415 volts, type ML-4. all as directed

S&F in repairs Bimetalic Overload relays suitable for Power Contactor 40Amps, 415 volts, with coil rating 230/415 voltstype ML-3. complete all as directed

S&F in repairs Bimetalic Overload relays suitable for Power Contactor 70Amps, 415 volts, with coil rating 230/415 volts complete of complete all as directed

S&F in repairs SDz5 star delta timer 50 Hz complete all as directed and specifed.

M&L in repair of rusted & crack CI/DI water branch connection 150 to 300mm dia by using mechanical joint with connecting all accessories complete all as specified and directed byEngineer-in-Charge. Note : (i) cost of gasket and nut bolts ,washers'jointing of materials as required are inclusive in above job. ii) Required T&P for job is provided by the Contractor is deemed to be included in the item rate. (iii) Excavation for pipe is included in job Work.

Disconnection and removing the broken S/S spindle with checknut and S&F brass spindle of same size and length along with checknut suitable for sluice valve 300 mm bore PN 1.6/PN1 of exisisting makes including threading machining and Lathe work complete along with fixing material such as gland packing nut and bolts complete.

All as per item No 47 above but 200 mm bore.

All as per item No 47 above but 150 mm bore.

M&L for CI special/fittings suitable for CI flanged/socket ends pipe upto 150 to 300 mm bore dia such as bends, (any radius and angle), tapers any type (straight, bend, increasing, decreasing or double socket etc) tee piece, single branch 'Y' junction, double branch, cross (all flanged), collars, caps & plug, tail pieces, reducers, mechanical joint, etc. complete all as specified and as directed,

Supply, installation, commissioning and testing of star delta stater fully automatic suitable for 30 HP/40 HP submersible pump, 415 volts 3 phase, 50 Hz including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG).

Material and labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earths strip 32 X 6 mm size by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

All as per item No 52 above here-in-above but earth strip conductor of size 25mm x 4mm and 32mm protection pipe.

S &F of single phase preventor(Phase failure relay) 415Volt,50 Hz,Type-VSP 3 complete all as specified and directed.

M&L for disconnecting removing the water meter 300 mm (NB) make Capstan B class flange end and transporting to authorized service center for repair, clibration, testing and refixing, comissioning, testing and fixing proper seal including nutbolts, rubber sheet etc of suitable size all as directed and specified.

Disconnection and removing the top cone unit (split casing cover) of the unserviceable pump 120HP along with suction, delivery pipe line, control valves etc and refixing the disconnected parts after replacing unserviceable parts with the new parts of same size, capacity and make and making the pump in serviceable condition including testing and commissioning complete all as directed for the following capacities:- Note:- The replacement of unserviceable parts with new parts will be measured and paid separately under respective items of sch 'A' as supply only and labour element for fixing including greasing, overhauling and packing of pump set will be included in the unit rate quoted for this item.

All as per item No 56 above but 110 HP.

Disconnection and removing the unserviceable Electric motor 120 HP and transporting the same to work shop for rewinding and fixing the same in its original position after repairs, including testing and commissioning complete all as directed

All as per item No 58 above but 110 HP.

Material & labour rewinding of 120 HP electric motor with fine enameled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motor including taking out old rewinding complete all as directed.

All as per item No 60 above but 110 HP.

Supply only spares parts suitable for 120 HP pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Bearings suitable to the pump set (3309)

Bearings suitable to the pump set (6309)

Gasket

Shaft stainless steel suitable for pump set including machining, threading, metaling & lathework complete.

Bearings suitable for 120 HP motor (for drive end & dead end) (317C-3/6317C-3)

Bearings suitable for 120 HP motor (6318)

Supply only spares parts suitable for 110 HP pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Impeller lock nut

Impeller sleeves

Bearings suitable to the pump set(3309)

Bearings suitable to the pump set(6309)

Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete.

Bearings suitable for 110 HP motor (for drive end & dead end)(6316&6314)

Material and labour for spray painting of the pump set of capacity 120 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Material and labour for spray painting of the pump set of capacity 110 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of colour as approved by GE.

Disconnection and removing of the 7.5 HP monoblock pump along with suction, delivery pipe line, control valves etc and finding out the unserviceable parts and refixing the disconnected parts after replacing of unserviceable items with new of same size and capacity including testing and commissioning complete all as directed . Note:- (i) Unserviceable parts will be measured and paid separately under respective items of sch 'A' (ii)Greasing, overhauling and packing of pump set will be include in the unit rate.

Material & labour rewinding of 7.5 HP electric motor with fine enameled bared copper conductor of same gauge weight and turn along with insulating materials such as impregnated paper, cotton tap, varnish etc and keeping the rewinding in to the hot air oven till moisture evaporates and achieving proper insulation results and reassemble the motor including taking out old rewinding complete all as directed for the following capacity.

Supply only for spares parts suitable for 7.5 HP monoblock pump pump set:-

Coupling along with nut, bolts and key unit complete

MS Impeller of suitable capacity

Impeller lock nut

Impeller sleeves

Bearings suitable to the pump set

Gasket

Shaft stainless steel suitable for pump set including threading, machinery & lathe work complete.

Bearings suitable for 7.5 HP motor (for drive end & dead end)

Material and labour for painting of the pump set of capacity 7.5 HP with suction/delivery pipe line approx 10 mtr including valve with two coats of synthetic enamel paint of color as approved by GE.

Taking out defective submersible (vertical) pump set of capacity 7.5 HP/10HP from bore well for repair by lifting GI tubing of size 50mm to 150 mm GI/CI/MS pipe from upto 220 to 250 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pully block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and ovhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pumpset with motor with one coat of synthetic enamel paint after cleaning and scrupping and shifting back to borewell, lowering commissioning and testing on full load complete all as specified and directed . Note :- (i) The rate quoted for this item shall includes labour charge only for maint repair and replacement of defective/UNSV spares/accessories. Spares are to measured and paid separately under subsequengt items. (ii) Cost of other minor items/ spares such as nut, bolts, washer, gaskets,paints etc which are not covered under Sch 'A' but required for efffective functioning of the plant shall be deemed to included in this items.

All as per item No 70 above but 3 HP/5 HP.

Supply only the following items/parts for 7.5 HP/10HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

SWR rope 6mm

Supply only the following items/parts for 3HP/5HP submersible borewell pump etc.

Thurst bearing complete

Gun metal bearing bush

Stainless steel studs and nuts

Shaft for pump

Shaft for motor

Stainless steel motor coupling with key

SWR rope 6mm

submersible cabe 3 core copper conductor cable 6 sq mm

Dismantling the motor of submersible (vertical type) pumpset of capacity 7.5HP/10HP, removing the existing burnt out winding and re-winding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, three phase, 415Volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as directed

All as per item No 74 above but 3 HP/5 HP.

Spray Painting of the MS fabricated structure of Sedimentation tank (two parts) including filter bed, outlet sluice valve complete by one coat of synthetic enameal paint as approved. Note :- necessary safety precautions should be taken in the cost of using safety belts is deemed to be included in the cost

Supply and fix in replacement CI Foot valve unit double flap , suitable for 200mm bore incl required nuts and bolts etc and cone set the same to the suction pipe of the pump set availble in to the sum appx hight of 14 feet below the ground level of the sump all as specified and directed. Make:Kirloskar/Upadhya/Leader .

All as per item No 77 above but 250 mm bore.

All as per item No 77 above but 150 mm bore.

Excavation in trenches by mechnical means (hydraulic excavator) not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all kind of soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers of soil not exceeding 25cm.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point of rock.

Taking up cast iron water mains 300mm dia class B (including all fittings), with spigot and socket ends and lead joints including burning out joints / tyton joints complete all as specified and as directed.

All as per item No 83 above here-in-above but 200mm

All as per item No 83 above here-in-above but 150mm

Relaying only old CI/DI pipe in good condition/pipe taken out from trenches for repairs in any length including fittings etc. of size 300 mm bore

All as per item No 86 above here-in-above but 200mm

All as per item No 86 above here-in-above but 150mm

Supply and fix cast iron pipes with spigot and socket ends centrifugally costed class B in any length suitable for rubber tytan joint and Laid in trenches of size 300mm bore.(Make: Electrosteel/ Kapilansh Dhatu Udyog).

All as per item No 89 above here-in-above but 200mm bore.

All as per item No 89 above here-in-above but150mm bore.

M&L for burning out lead joint in position , including removing lead to store / stacked at site to issue under credit of 300mm bore CI Pipe line

M&L for Run lead joint of 300 mm bore of spigot socket pipes and fitting, including caulking properly and making joint leak proof all as directed and as specified.

Servicing of Iron removing plant with pressure filter, catalytic media, air compressure, suitable for back washing of capacity 1000 GL/H complete in all respect. Make ELGI.: U/S spare parts shall be measured and paid separately as supply only here in after).

Air filter

Air oil separator

Oil filter

Air Lub oil

S&F in repair Pressure gauge range 0-21 KG per cm square for centrifugal pump/VT Pump set proper fix suitable point with suitable fixing arrangement (i.e nut bolt, boresuitable,fixing pipe for pressure gauge on mounting all as directed.

Supply & fix in replacement champion/turner style graphite gland packing of sizes as 8/10/12/16mm thick. For motor/sluice valve.

Dismantaling of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level).

M&L for Cement concrete 1:2:4 B-2 using 40mm graded stone aggregate in foundations, filling and mass concrete.

Repair to CI valve for back wash in filter plant ( Plate type) 200MM/300mm, including threading, machinery and lathe work complete along with fixing material such as Rubber sheet packing, nut and bolts,etc complete.

All as per item No 99 above here-in-above but150mm bore.

M&L in repair chequered plate including cut to required size and making provision of handle made out of 6 mm plane rod,including painting with two coats of synthetic enamel paint over one coat of red oxide all as directed .

Taking down existing UNSV sluice valve and supply & fix new Sluice valve of 80mm bore rising spindle type (Gear type) PN-1.6 heavy duty ISI marked as per (IS-14846) with flanged ends with 02 Nos of rubber gaskets, nut bolts and washers along with SS spindle and oprating wheel of following sizes :- Make : Kirloskar/Leader/Venus.

All as per item No 102 above here-in-above but150mm bore.

All as per item No 102 above here-in-above but 200mm bore.

All as per item No 102 above here-in-above but 300mm bore.

Supply and fix in repair and replacement of leather flapper for the 200mm CI Foot valve unit, including required nuts and bolts etc and cone set and fixing the same to the suction pipe of the pump set availble in to the sump appx at a height of 15 feet below the ground level of the sump all as specified and directed.

Spray Painting of MS sheet cover for Valve chamber cover/US sump cover/Air release valve/ filter water reservoir square type of water supply all installation with two coat of enamel paint colour coat over a coat of red oxide are approved make by GE.

S&F in repair Mild steel work in Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F in replacement of microprocessor based electronic water level indicataor based on 3 wire interfacing system in between OH Tank/UG Tank sensor to main water level indicator units showing indication in percent by seven segment LED display in 10 step (10%, 20%, 30% ............100%) having 10 combined sensor for total depth of tank of make : Serval/Optic/ IEC/Benzer with all fixing/grouting arrangement suitable for RCC OH Tank/UG Tank of 0.5 to 1.5 lakh gallons capacity including dismantling and taking down old unserviceable water level indicator, any type and depositing to MES store yard complete all as specified and directed. Processor based electronic water level indicator shall also comprising of the following items:- Multi level (10 to 100%) indication in three digit with seven segment with bright LED display. Sensor with suitable fixing arrangement in over head tank haaving electronic circuit to transmit the sensing signal of each level to display unit shall be fitted in pump house. Controller/power unit with sensing volts (6-12 volts) enclosed with sheet metal enslosure/wooden board and hylum sheet including proper mounting arrangements. PDC insulated multi- strauded copper conductor communication cable 2.5Sqmm, 3 core from LT Panel to controller/power unit drawn through 20mm dia non metalic PVC conduit medium grade with all accessories including all fixing arrangements. Hooter with ON/OFF switch to alarm the pump operator when tank is full.complete all as directed by EIC.

Supply and laying or fixing or passing through pipe in replacement ,testing and commissioning 1100 volts grade heavy duty cable with PVC insulated multi strand copper conductor cable size 95 Sqmm, single core unsheathed flexible including of suitable size lugs and connection plate of sutiable type all as specied and as directed

Supply and laying or fixing or passing through pipe in replacement ,testing and commissioning 1100 volts grade heavy duty cable with PVC insulated multi strand copper conductor cable size 70Sqmm, single core unsheathed flexible including of suitable size lugs and connection plate of sutiable type all as specied and as directed

All as per item No 111 above here-in-above but of size 35 sqmm.

All as per item No 111 above here-in-above but of size 25 sqmm.

Supply, installation, commissioning and testing of smart star delta stater fully automatic ,LCD based,Digital time setting ,Smart/Auto switch ,protects motor against reverse running & unbalanced voltage conditions for upto 120 HP centrifugal pump, 440 volts 3 phase, 50 Hz including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG).

Supply, installation, commissioning and testing of DOL stater fully automatic suitable for upto 7.5HP monoblock pump, 415 volts 3 phase, 50 Hz,10-40A including taking out of existing u/s starter as directed. Make- L&T/Siemens/Schneider (CG).

M&L cleaning the Decrin dozer assembly complete by opening of nut, bolts gate valve and connected GI fitting and refixing/assembling complete all as specified and as directed.

Comprehensive maintenance and repair of calcium hypochlorite based electronic automatic dosing equipment 100 Ltr capacity of any type and make complete with dozing tube and solution drum and other accessories required. Note :- (i) Spare items/parts required for chloronomes plant shall be measured and paid separately under relevent items. (ii) Cost of items /parts which are not covered in Sch 'A' but are necessary for the satisfactory functioning for the plant shall be included in the rate quoted for this item. (iii) Dosing pump to be cleaning twice in a month (15 days) and serviceability report to be submitted to Engr-in-charge for office record. (iv) Labour charges for removal of unserviceable parts and fixing of spare items/parts (supplied under the item No-84) shall be deemed to be included in the rate quoted for this item.

Supply only for replacement of the following spare parts of decrine dozer :-

Pump head (Ferrules 1/4" & Duckbill included)

Roller assembly

Pump tube

Injection check valve 3/8"

Weighted suction line strainer 3/8"

Rotor assembly with bearing brackets & tolerance ring

Coil 250V 50Hz

3/8" White suction/Discharge tubing

Supply and laying of flexible PVC pipe 80mm bore for connected with D-watering pump

M&L for dismantling soft starter for 120HP Pump set and taking to workshop for fireware updation and replacement of motor control PCB EMZ4E soft starter and reinstalling, commissioning and testing complete all as specified and directed.

Servicing of D-Watering Pump capacity 7.5 HP and taking out the defective/unserviceable parts and re-assembling the same after repair/replaced and testing complete all as specified and directed. (Note : U/S spare parts shall be measured and paid separately as supply only here in after).

Diesel filter

Oil filter

Oil pressure gauge

Hose pipe set with clamps & clips complete.

Testing of Treated water (Drinking water) sample as per IS - 10500 including collecting of sample from the pump house and handed over it to the authoriesed lab for the testing purpose all as specified and directed.

Testing of Raw water sample as per IS - 10500 including collecting of sample from the pump house and handed over it to the authoriesed lab for the testing purpose all as specified and directed.

M/S JAI BHAWANI CONSTRUCTIONS

SHRI RANI SATI TRADERS

M/s Dara Constructions, Pulgaon

M/S Maa Durga Constructions,Pulgaon

Attar Singh and Sons

Bidder Name

Attar Singh and Sons

SHRI RANI SATI TRADERS

M/s Dara Constructions, Pulgaon

M/S Maa Durga Constructions,Pulgaon

M/S JAI BHAWANI CONSTRUCTIONS

SHUBHAM SALES