PROVISION OF IRON LADDER FOR ACCESS TO ROOF OF MAP SMQS RENOVATION OF WASHROOMS AT ASD 30 FIRST FLOOR AND GROUND FLOOR AND PROVISION OF ESD TILES IN OLD RSD L BUILDING AT 11 BRD

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of cement concrete (un-reinforced) of any description & in any description and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of unreinforced cement concrete as in roofs, floors (other than ground floors), in any description of beams, staircases, landing, chaj-jas etc including removing of existing APP membrane any thickness / Screed any thickness etc and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site for credit & removal where directed.

M & L for PCC 1 :4 : 8 type D2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete complete all as specified and directed

M&L for reinforced cement concrete 1:2:4 type B0 using 12.5m graded crushed stone aggregate in chajjas / slabs with necessary form work complete allas directed. Note :- Reinforcement shall be measured and paid for separately.

Forming jambs, etc to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar 1:4 complete all as directed..

M&L for Brick work with well burnt best quality locally available bricks, old size bricks, straight or curved on plan to any radius built in any description in cement mortar 1:6 complete all as directed

All same as per item No 11 here-in-above but Brick work built in cement mortar 1:4 -do-

Form work to rough finished surface of sides and soffits of suspended slabs such as roof slabs, floor slabs, landings, chajjas and similar work; not exceeding 200mm thick (Horizontal or sloping)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x100 mm single rebate comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made Make : ECHON/Sintex/Rajshree/Navaratan

All same as per item No 14 here-in-above but size of frame 45 X 70 mm single rebate -do-

S&F 28-30 mm thick Prelaminated moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on both side with wood grain texture with density not less than 650 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified

S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with arrangement for exhaust fan & include the following :- (i) Aluminium frame section 45x25x1.80mm. (ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape. (iii) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc.

S&F100 mm size butt hinges, heavy weight weight cold rolled mild steel and fixed .

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 150 mm size extruded aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per serial item No. 23 here-in-before but 6 to 8mm dia -do-

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in floor and finished the surface even & smooth without using extra cement complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L preparing old / untreated wall / ceiling surface and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1-2 mm thick white cement based wall care putty as specified complete all as specified.Note : (i) Painting shall be done using Airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper/ primer should be able to spray in hard to reach areas and penetration of distemper on the surface

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

Taking down old rusted / wornout 15 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

S&F in repair 15mm dia cast copper alloy Bib taps fancy type , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repair 15mm dia cast copper alloy two way Bib taps , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repairs 15mm bore Stop valve /Angle cock , fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.

S&F in repairs 15mm bore Stop valve /Angle cock , cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S&Fin repair health faucet ABS body with wall hook and 1.80 metre long SS braided rubber hose pipe and wall hook mounted type complete. Make: Prayag Cat No BEA-40 or equivalent in approved make.

S&F in repairs brass chromium plated shower rose 75 mm dia with CP Arm with swivel joint, any size, including fixing to steel pipe or union.complete all as directed.

S&F in repair stainless steel soap dish as per existing or as ordered fixed with & including Chromium plated brass screws & plastic cleats all as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as directed

S&F inrepair 20mm dia , 60 cm long Towel rail brass chromium plated with flanges fixed on wall with PVC rawl plug & cadmium plated brass screws.

S & F in repairs PVC connection 15 mm size with PTMT nuts, 450mm long complete all as specified

S & F in repairs Bottle trap of 40mm dia of discharge pipe of PTMT having minimum water seal of 25mm .(Minimum weight 40mm-270 gms) complete all as specified and as directed.

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) capstain head ,down high pressure with or without lettered 'Hot or Cold' with long screwed shanks & fly nuts suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S&F in repairs vitreous china urinal, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and as directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

M&L for High density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm of 50mm bore with & including all fittings and fixed complete to walls, ceilings or in floors etc including taking out old unserviceable pipe all as specified & directed

All same per item No 54 here-in above but 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall .

S & F 110 mm bore, PVC (SWR) bends of any radius with access door complete all as specified and directed.

S&F 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F 110mm bore PVC (SWR) vent cowl jonting the same with solvent cement complete all as directed.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) concealed on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bell point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5/6 Amp on independent board

(c) One 3 pin socket point 5/6 Amp on same board with other switches.(to be provide new point as user reqairment)

S&F switch modular type single pole one way 6 Amp , 1 Module , with all accessories complete all as directed. Make: Legrand Cat No. 6755 01 or equivalent in Philips / Crabtree / ABB / Havells

S&F socket outlet multipurpose 2/3 Pin for 6 / 16 Amp modular type with all accessories complete all as directed. Make: Legrand Cat No. 6755 55 or equivalent in Philips / Crabtree / ABB / Havells

S & F Ceiling rose surface bakelite White / Ivory / Urea finish 50 mm dia three terminals including supply and fix PVC square mounting block complete all as specified and directed.

S & F and connecting up LED 20 watt fitting 6500K 4 feet with 120 lumen/watt,aluminum housing extruded in thermal conductive material with powder coated in white colour Extruded serration High Optically efficient plastic FR grade material in milky white,Spring Steel Nickel plated,Inj. Moulded engineering plastic Brown in colour Five year written warranty from manufacturer including 23/00.0076 size 3 core copper flexible wire from connector to ceiling rose/adoptor fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. Crompton cat No CCS-100-20-65-HL2-DP-NWH or equivalent in Philips/Havells/Wipro ).

S & F and connecting up LED 5 watt fitting 6500K 1 feet with 100 lumen/watt,aluminum housing extruded in thermal conductive material with powder coated in white colour Extruded serration High Optically efficient plastic FR grade material in milky white,Spring Steel Nickel plated,Inj. Moulded engineering plastic Brown in colour Five year written warranty from manufacturer including 23/00.0076 size 3 core copper flexible wire from connector to ceiling rose/adoptor fixed as per manufacturers instructions and making necessary electrical connections and testing on completion complete all as directed. Crompton cat No CCS-103-05-65-SL-DP-NWH or equivalent in Philips/Havells/Wipro ).

S&F Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 2 way horizontal type, single door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

M&L for submain wiring with 2 runs of 2.5 Sqmm single core PVC insulated, unsheathed, multi stranded copper conductor and one single core 2.5 Sqmm PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit of size 20/ 25 mm dia concealed in walls etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 2.5 Sqmm cable , one run 2.5 Sqmm cable and one run of PVC shall be measured as one unit length) .

S & F exhaust fan sweep made of sturdy Engineering plastic complete with louvers shutter,voltage 230 V, 50 Hz, 1200 RPM noiseless,copper winding of sweep 300 mm with self closing louvers and four blades fixed in position after necessary cutting wall to size as ordered to fix the fan as per manufactuers instructions , making good of the distured surface of wall as per its original specifications , making necessary electrical connection & testing on completion all as directed . .Make :- Havells/ Usha/ Crompton (Note :(i) The quoted is inclusive for any addtional cutting of wall & making good of disturbed surface of wall to its original specifications).

M&L to earthing pit chamber including replacement of PCC chamber, cement concret pit with cast iron miled steel frame embedded in the massonery enclouser finished flushed & PCC cover 10 mm thick (300mmx300mm size having locking arrengment hinged to PCC frame all as shown under electrical plate of SSR Pt - I 2009 and as directed including painting the external surface of chamber & cover with enamel paint in diffrent colour as directed and writing earth results & date of test carried out with white paint on black painted background, complete all as directed.

M&L for test point terminal block made of gun metal or phosphorus bronze size 75mm x 75mm x 25mm, drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screws with nuts & washers complete, fixed on ebonite sheet 6mm thick fitted on MS flat 50x5mm bent to shape etc, all as specified & as directed.

Supply only PVC insulator for GI/Aluminium strip supporter adequate to accomadate strip of 32 mm with fasteners complete all as specified and directed.

M & L for prepration of old painted surface of earth pit chamber & cover of any size & painting of the same with two coats of synthetic enamel paint all as directed .

Please Enable Macros to View BoQ information