Spl repair of bldg No P-05 of AA at Tibri Mil Stn under GE Gurdaspur.

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer.

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified and directed.

Roughening the surface of old concrete floor picking sweeping cleaning and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate finished even and smooth without using extra cement as in roof padding complete all as specified.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed complete all as specified and directed and all as per manufacturer's instructions.

M&L for 40 mm thick brick tiles laid over and including 15 mm thick screed in cement mortar 1:6, Joints grouted and flush pointed in cement mortar (1: 3) mixed with 5 % of crude oil by weight of cement, flush pointing in cement mortar (1:3) shall be done as a separate process, complete all as specified and directed.

All a per Srl item No 07 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 01 shall be reused after necessary cleaning of mortar)

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs, kerb, coping etc. complete all as specified and directed.

Supply only integral water proofing compound.

Demolition of cement concrete above ground floor and in any position (unreinforced) as sunken etc.

M&L for 15mm thick cement screed in CM 1:3 admixed with integral water proofing compound FOSROC conplast X421IC @ 130ml per bag of cement incl a bonding coat of FOSROC Nitobond AR cement slurry coat (1 vol of Nitobond AR+ 1.5 Vol of water+ 1.5 Vol of cement) complete all as specified.

M&L for applying two coats of Nitobond SBR cement slurry (1 Vol of Nitobond SBR+ 1 Vol of water+ 3 Vol of cement) water proofing coating on the entire surface of sunken portion all as specified.

M&L for PCC 1:5:10 type E2 using 40 mm stone agg filling fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level.

M&L cement concrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection thickness of 75mm finishing the surface even and fair with joints to full depth at corners, along the wall and @ 3 meters c/c filled with mastic mortar complete all as specified

M& L Non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm but not exc. 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 and including demolition of existing tiles and screed complete all as spcified and directed.

M&L for glazed ceramic coloured tiles in vertical surface of size 350x250x7mm/ 450x350x7mmmm thick joint free on and including 10mm thick screed bed in cm(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles including demolition of existing tiles and screed complete all as speciifed and directed by EIC.

Demolition Stone slabs and tiles of any description or thickness in floors, aprons including screed etc.

M & L for Green Marble work 16-18 mm thick (table rubbed and polished) in steps, jambs, Shelves, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for upto 12m height complete all as directed.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs upto 12m height all as specified & directed.

M&L TMT bars 6 to 8mm dia cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia complete all as specified.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work all as spd.

Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for rendering 12mm thick plaster in cement mortar 1:6 on fair face of brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on other than fair face of brick or concrete surfaces of walls, finished surface even and fair with WPC, upto height 12m complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately

M&L preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed.

M&L preparation of new plaster surface and applying two coats of cement base paint on walls complete all as specified and directed.

M&L for Preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on existing surfaces and applying two coats of oil bound distemper on walls complete all as specified and directed.

M&L for Preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on existing surfaces and applying two coats of white wash on walls complete all as specified and directed.

M&L for Preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on existing surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment, preparation of old surface and applying two coats of cement base paint on wall complete all as specified and directed.

M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint ht upto 12m complete all as specified and directed.

M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 30mm thick factory made solid PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides incl 6mm thick lipping/ beading fixed with nails on all sides complete all as specified and directed.

S&F glazed and skeleton shutters 35mm thick of 2nd class hard wood open rebated and prepared to receive gauge & glass etc with edge of sash bar and number edges of framing plain chamfered beads for securing glass etc size of number of shutters as spd SSR Part-I & section 8 clause 8.24 (a) complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, ISI marked and fixed complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern spring, including roller and roller plate including fixing through welding/bolts/ screws in metal/wooden frame complete all as specified and directed.

S&F Aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long, ISI marked complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy, type B-21 with galvanised mild steel hinge pin, anodised and fixed with metal surface through bolts, screws complete all as specified and as directed.

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of red oxide primer and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick Figured ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specifiwd and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from steel frame complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down existing complete all as specified and directed.

Fixing only old steel tubing including new fittings 15mm bore in new or old position including cleaning the same incl taking up or down existing complete all as specified and directed

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down existing complete all as specified and directed.

Fixing only old steel tubing including new fittings 20mm bore in new or old position including cleaning the same incl taking up or down existing complete all as specified and directed

S&F GI tubing 32mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings as spout complete all as specified and directed.

S&F rotational moulded polytheylene white triple layered white water storage tanks ISI marked of capacity 1000 Litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia. brass float valve, high pressure, with polythene float and flynut complete all as specified.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair bib taps 15mm dia cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed. Make :- Prayag (Cat No 7506) or equivalent as per Appx 'B' as approved by GE.

S&F in repair stop valves or angel valve 15mm bore cast copper alloy chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. Make :- Prayag (Cat No 7510) or equivalent as per Appx 'B' as approved by GE.

S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore. Make :- Prayag (Cat No 7502) or equivalent as per Appx 'B' as approved by GE.

S&F in repair Brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 225mm long, 15 mm size complete all as specified and directed.

S&F Stainless steel tubular 20 mm dia towel rail 60 cm long fixed to wall complete all as specified and directed by Engr-in-Charge.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified complete all as specified as directed

S&F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve and 32mm bore PVC flush pipe etc complete all as specified and directed.

S&F SS Soap dish, oval type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, flushing cistern etc complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repair for Vitreous China wash down water closet pan (pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap including stainless steel L-type jet spray with 1 m hose pipe, complete all as specified and directed.

S&F in repair Vitreous China urinals, half stall type Min Size 345X320X560 mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including Brass cp Urinal spreader 60mm long brass screws, pointing around urinal back in cement and 32mm dia CP Brass waste coupling with 32mm dia pipe complete all as speciifed and directed.

S&F in repair Vitreous china counter top oval wash basin, white, size 550x400mm, including 32mm dia CP brass waste coupling with 32 mm dia PVC waste pipe complete all as specified and directed.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC(SWR) branch piece single(single Y) equal or unequal 110mm bore with oval access door

S&F in repair PVC (SWR ) bends 110 mm bore any radius

S&F in repair PVC (SWR ) Double junction (double-T Cross ) 110 mm bore equal or unequal with oval access door

S&F in repair PVC (SWR ) vent cowl 110 mm bore

M&L in repair PVC(SWR) floor trap incl jointing with solvent cement 100mm dia complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1:2:4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof/wall coverings/crumple joints complete all as specified and directed.

S&F in repair Aluminum, 0.56 mm thick plain, sheet in wall cladding, crumple joints and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood /steel/Concrete framing with plain 40 mm lap joints including bending or turning up, mitred angles, etc. as required complete all as specified and directed by EIC.

S&F machine cut kota stone slab flooring 20-22mm thick over and including cement screed 15mm thick in 1:4 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) complete all as specified and directed by Engineer-in-Charge.

Labour only grinding of existing machine cut kota stone slab flooring including rubbing and polishing complete.

S&F in repair 18 mm thick plywood , grade BWR, laminated on both side with decorative choice lamination, fire resistant, moisture resistant type fixed with screws to timber/steel frame work for cupboard shutter, shelf, partition etc including 6mm thick lipping of 2nd class hardwood fixed with nails on all sides complete all as specified and directed.

S&F 75mm size hasp and staple safety type stainless steel with mild steel hinge pin including bolt to hinge plate and fixed with screw all as specified and directed.

S&F Extruded aluminium alloy handle fabricated type anodized of size 125 mm long ISI marked.

Supply and fixing cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F in repair stainless steel cockroach trap with waste hole, round 101mm dia complete all as specified and directed. Make :- Prayag (Cat No FT 22M) or equivalent as per Appx 'B' as approved by GE.

Taking down chowkats with shutter exc 1.5 sqm and n.exc 4.00 Sqm each (without taking off shutter for the chowkats and removing to store as spd

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 105x60mm all as spd including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:2:4 (type-B0) in the frames complete all as specified and directed.

S&F in repair 15 mm stop cock screwed to iron pipe cast copper alloy CP concealed type with long shank and capstan head for (Bath shower) in repair complete all as specified and directed.

S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, shall be measured and paid for separately

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm eachcomplete all as specified and directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of PVC insulated and PVC sheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to and including CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light point/ Fan/ bell point controlled by one way switch

All as per Srl item No 102 above but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 102 above but 5 amps socket outlet on independent board.

All as per serial item No.102 here-in-before but one light point controlled by two way switches.

All as per serial item No.102 here-in-before but wiring with FRLS copper wire including earth wire 2.5 sqmm of copper for 15 Amps 3 Pin socket outlet.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt , FRLS cable of size 6 sqmm including 6sqmm multistranded copper conductor FRLS cable PVC insulated for earthing duly connected with earth dolly, with approved colour coding including PVC conduit heavy grade, of not less than 1.2mm thick and 32mm dia., concealed in wall with accessories including cutting chases and making good to the disturbed surfaces as per existing and taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type.

S&F switch flush type 15 amps single pole one way

S&F socket outlet 3 pin 15 amps flush type

S&F switch piano 2 way 5A all as specified and directed.

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitabe for and upto 1 x 18/20W LED tube rod incl taking down old U/S fitting complete all as specified and directed.

S&F in replacement LED tube light 20W ultra bright LED polycarbonate tube light with very high efficiency suitable for fitting into tube light batten fitting complete all as as specified and directed. Note :- The contractor will submit the LM-80 and LM-79 report from manufacturer to Engineer-in-Charge before incorporating the items in work.

Taking down carefully ceiling fan complete fittings at site, removing fans, deposting to MES store yard and taking back to site for refixing complete all as specified and as directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to connector of fan all as specified and directed.

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as specified and directed.

S&F bell, AC, 230 Volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amps complete all as specified and directed.

Supply and fix for lamp holder angle type, PVC/ polycarbonate type with back plate, suitable for lamp holder base of and including 9 watt LED retrofit lamp complete all as specified and as directed.

M&L ceiling rose, 3 terminals/ phase/ PVC/ polycarbonate, isolated body

S&F in replaceemnt GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 40mm x 5mm thick and drilling of hole for and including nuts, bolts and washers including painting MS clamps with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used, 240 volt 8 way SPN with bus bar and double door complete all as specified and directed. Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

S&F in repair MCB single pole and neutral 40 amps complete all as specified and directed.

Material and labour for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar made out of Aluminium duly insulated with wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp: 4 Nos, MCB SP 40 Amp: 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable capacity as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil complete including dismantling existing all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core including taking down/out existing cable. Note: Excavation and earth work, sand cushioning, brick protection, GI pipe shall be measured and paid separately.

Excavating in trenches in soft loose soil including cutting road surfaces n. Exc 1.5 mtr wide and n. Exc 1.5 mtr in depth for poles, stay, cable, pipe etc including taking out brick protection getting out all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers each n. exc 25 cm thick in soft loose soil all as specified & directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified & directed.

Supply and lay brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15 cm before laying the cable & 8 cm after laying the cable complete all as specified.

Supply and fix exhaust fan, steel body AC single Phase 230V of size 300mm sweep with blades and frame and louvers complete all as specified and directed.

A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

Harbhajan electric co

M/s SODHI SALES CORPORATION

M/S DARSHAN & CO

buta singh and sons