SPECIAL REPAIRS TO SEA HAWK (BLDG NO. P-124) AT INS HAMLA

Amount

Dismantling/Demolition of existing roof terracing of cement/brick concrete(un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land complete all as specified Note : Demolition should be done by chiselling.

M&L brushing neat cement slurry @ 3 Kgs of cement per Sqm

M&L 10mm thick ready mix plaster , on fair faces of brick work or concrete surfaces and provn of on roof finished even and smooth using liquid water proofing compound as per manufacturers instructions Complete all as specified and directed. (Note :- Supply only liquid water proofing compound shall be measured & paid separately).

M&L for PCC 1 : 2 :4 type B0 (using 12.5mm graded stone aggregate) as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc mixed with approved water proofing compound all as per manufacturer'ss instructions on the roof surface to achieve requisite slope all as specified and directed. (Note : Supply only water proiofing compound shall be measured & paid separately)

Supply only polymer based liquid water proofing compound complete all as specified and directed.

M&L APP based polymeric membrane minimum over (Accessible) RCC roof specification sweighing 3kg/sqm and minimum 4mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application and Cleaning existing surface properly. Apply Priming on existing surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 Over the membrance provide 20-25 mm thick machine pressed cement concrete tiles 200mm x200mm over & incl cement screed bed 15mm thick in CM 1:4 set and jointed, pointed in neat cement slurry with grey cement .Note :- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane complete all as specified and directed".

M&L APP based polymeric membrane minimum over (Accessible) RCC roof specification sweighing 3kg/sqm and minimum 4mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application and Cleaning existing surface properly. Apply Priming on existing surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 Preparation of new or previous treated surface applying one coat of Aluminium paint all as per manufactures's instruction complete all as specified and as directed. .Note :- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane complete all as specified and directed".

Demolition of brick work built in CM incl. taking out roots vegetation if any at any position and removal to out side MD land

M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean radius built in CM(1:6) for MH complete all as specified

M&L for walling or random rubble , uncoursed well bonded, bedded and solidly, hearted built in CM 1:6 etc complete all as specified and directed.

Racking out joints/pointing to randum rubble or poly gonal rubble uncoursed or brought upto courses buil in cement mortar 1:4 complete all as specified and directed.

M&L for Raised pointing to randum rubble or polygonal rubble uncoursed or brought upto courses built in cement mortar and pointing to RR masonry with CM 1:4 complete all as specified and directed.

Hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 40 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course complete all as specified Note :- Hidden portion of masonry shall not be hammer dressed

Taking down cement plaster of any description in any position including racking out joints making key scrubbing down with water etc. and removal of debris out side MD land.

M&L 10 mm thick ready mix plaster , on fair faces of brick work or concrete surfaces andsurfaces finished even and smooth including necessary scaffolding complete all as specified and directed.

M&L 5 mm thick ready mix plaster over concrete surfaces of ceiling and provn of 3mm thick wall care putty on plastered ceiling surfaces; surfaces finished even and smooth including necessary scaffolding complete all as specified and directed.

M & L for 15mm thick ready mix plaster using WPC @ 2% by weight of cement on brick work or concrete surfaces; surfaces finished even and smooth including necessary scaffolding complete all as specified Note : Water proofing compound shall be measured & paid seperately.

M&L for Preparation of old / new plastered or un-plastered surfaces of wall by applying 3mm thick wall care putty on plastered surfaces of wall; Birla/JK white putty smooth finished ,Make Royal of Asian Paint or Nerolac impressions.

M & L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with roller over a coat of alkali resistant primer.etc complete all as specified and directed .

M&L for complete removal of existing surfaces including washing / rubbing down with water of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed .

M & L for preparation of new plastered surfaces on ceiling and applying two coats of white wash with complete all as specified and directed.

M & L for preparation of new plastered surfaces on ceiling and applying two coats of oil bound distempe complete all as specified and directed.

M & L for preparation of old plastered surfaces on ceiling and applying two coats of oil bound distempe complete all as specified and directed.

M&L for complete removal of existing surfaces on ceiling and applying two coats of white wash with complete all as specified and directed.

M&L for preparation of NEW plastered walls surfaces for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for complete removal of existing surfaces including washing / rubbing down with water of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Demolition of cement concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M &L PCC 1:3:6 type C2 75mm thick as in plinth protection finished even and smooth using extra cement compete all as specified.

M&L 25mm thick cement concrete type B-1 1:2:4 (using 20mm graded stone aggragate) 0vr in base of floor

75mm thick cement Concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in floor/sub base and finished even and fair complete,all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc complete all as specified and directed.

Dismantling stone slabs or pcc tiles of any description or thickness in steps, landing, flooring and similar work laid, bedded and pointed in cement mortar complete.

M/L for 15 to 20mm machine cut kota stone slab as in riser of steps, skirting, dado and pillar, cills and jambs laid over cement mortar backing coat jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishand including over 15mm thick screed bed or bedding layer in CM1:4 complete all as specified and as directed by EIC

M&L machine cut kota stone slab flooring 20 - 25mm thick over 20mm cement screed in CM 1:6 laid and jointed with gray cement slurry mixed with pigment to match the shad of the slab including mirror polishing complete all as specified and as directed by EIC

M&L Marble work other than white or black/Baroda green 18 to 20 mm thick (table rubbed and polished) in cooking platforms, jambs.flooring and like over and including provision of 15 mm thick cement mortar (1:4) including pointing in colour cement (1 :2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. .

M&L for 15 -18mm thick granite stone slab (of any type) machine cut (in one piece) supported with 16mm thick marble stone base, bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigment to match the shade of stone in cooking platforms WHB counter top, vertical supports including grinding and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as steps, cooking plateform, and other similar situations complete all as specified and directed.

M&L coloured (light shade) vitrified ceramic tiles of size 600mm x 600mm x 10mm thick in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. incl 15 mm thick screed bed in cement mortar 1:6 including finishing even and fair complete all as specified.

M&L coloured (light shade) vitrified ceramic tiles of size 600mm x 600mm x 10mm thick on vertical wall skirting etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as rendering cement plaster, 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces to receive tiles complete all as specified and directed.

M&L Non skid ceramic colored tiles, edge cut 7 to 8mm thick square or rectangular) area of Each tile exceeding 0.11 sqm but not exceeding 0.18mm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile incl 15 mm thick screed bed in cement mortar 1:4 including finishing even and fair complete all as specified.

M&L Coloured glazed ceramic tiles of size 350x 450 x 7mm thick,on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces inc rendering cement plaster, 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces to receive tiles complete all as specified and directed.

M&L Johnson endura paving tiles of technocommercial equivalent of size 300x300x10mm thick set and jointed in neat cement slurry and pointed with white cement to match the joint incl 20 mm thick screed bed in cement mortar 1:4 over including finishing even and fair complete all as specified.

M&L 50 mm Sand filling under floors or in foundations including watering and consolidation

M&L for machine pressed glazed precast concrete interlocking paver block of any colour, shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigmen in floors laid over sand cushion complete,all as specified and directed.

Taking down chowkats of frames with shutters (without taking off shutters from frames) area exceeding 1.50 Sqm but n exc 4 sq. m each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damages to jambs , walls for taking out hold fast shall be finished idetical to existing finish without any all as specified and directed by Engr- in - charge

Taking down chowkats of frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damages to jambs , walls for taking out hold fast shall be finished idetical to existing finish without any extra cost of Govt) all as specified and directed by Engr- in - charge

Taking down shutters of any description exc.1 sq.m and n.exc. 2 sq.m Each and refixing in the same opening complete all as specified and directed.

Dismantling of boarding ,any description and in any position complete all as specified and directed

M&L for 18/19mm thick prelaminated particle board with teak wood beading, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L for 2nd class hardwood moulding n. exc 6 sqcm as in cornices, picture rails and the like such as in prelaminated particle board complete all as specified and directed.

S&F continous (piano) hinges 40 mm, mild steel, bright finish or electro-galvanised complete all as specified and directed.

S&F 150mm size hasp & staple, aluminium anodised, safety type, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 2nd class soft wood as in plain, solid, straight, chowkats and frames, wrought , framed rebated on the solid, rounded or chemferred, put together with glue pinned at joints complete all as specified.

S&F 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F extruded Powder coated aluminium section as in Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and all directed

S & F aluminium grill conforming to DG- 102 of Deco Grill or equivalent , (10mm X 5.2mm) thick of approved design or equivalent as approved by Accepting Officer and fixing with and including 'F/U' channel not less than 1.5mm thick complete all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, in opening as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of exturded sections or cast aluminium alloy all as specified and directed

S&F 150 mm long aluminium bow handles cast type anodised.

S&F 200 mm long aluminium anodised barrel tower bolt of extruded section.

S&F butt hinges med weight cold rolled MS, size 100 mm.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel pain complete all as specified.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore20 mm complete all as specified. -

S&F Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. of nominal Outer diameter of pipes 20 mm complete all as specified.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore25 mm complete all as specified. -

S&F Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. of nomina Outer diameter of pipes 25 mm complete all as specified.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 32 mm complete all as specified.

SS&F 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches of nominal Outer diameter of pipes 32 mm complete all as specified.

Taking up or down steel tubing with connections for cleaning for refixing or removing to store yard complete of bore 40 mm complete all as specified. -

S&F 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches of nominal Outer diameter of pipes 40 mm complete all as specified.

Demolition carefully RCC work as in, Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended worketc by low impact Hammer/Breakar without damaging the structure & cleaning and disposal of debris out side the MOD land. complete all as specified and directed.

M &L for precast cement concrete block masonary with solid blocks with 1:3:6 type C1 using 20mm graded stone aggregate as exc 10cm in width and setting in mortar 1:6 complete all as specified and directed.

M & L for RCC M 30 Design mix as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and directed.

M & L for Use and waste of Formwork to soffits of suspended slabs such as roof slabs, water tank staging floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)for flat and rough surfaces complete all as specified and directed.

M & L TMT bars 10mm dia and over cut to length, bent to shape reqd, inculding cranking,bending spirally for hooping for Columns, hooking ends and binding with and incl MS wire(annealed) not less than .90mm dia complete all as specified and directed.

S&F rotational moulded polythylence water storage tanks 2000 Ltr cylindrical vertaical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 2000 ltrs including disconnecting the unserviceable existing tanks complete screwed for iron pipe or brass ferrule directed

M&L in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete 25mm dia complete all as specified and directed.

M&L Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed

M&L Waste fittings, brass, chromium plated for glazed ware sinks, asins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed waste fitting of 40 mm bore, brass, chromium plated for glazed ware wash basin etc

S&F EWC wall hung WC With in built jet pp soft close silm seat hinges hind ware wall hanging type with plastic sheet cover all as specified and directed of size (H x W x P) 365 x 525 x 400 mm with ‘P’ trap distance 22.5 cm complete all as specified and directed. Make: Cera Cat No 92051 (ESSENCE) , Jaquar ;- SLS-WHT-6951 JPPSM or equivalent.

S&F vitreous China squatting pan, 'orrisa' pattern wc of size 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe but including 'P' or 'S' trap and provision of lime concrete bedding in repairs. Note:- flushing cistern and flush pipe will be measured and paid under supply only rate.

Supply only PVC connector 15mm size with PTMT nuts of length 450mm

M&L PVC single piece slim concealed cistern body with installation kit & P type drain pipe connection set for wall hung WC flushing cistern, with inlet, ball valve, float including fiush control plate and flush pipe and fixed in repairs complete all as specified and directed. Make: , Jaquar ;- JCS - WHT-2400P or equivalent.

M&L PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32mm dia and fixed in repairs complete all as specified and directed.

M&L Wash basin, Vitreous China white (Flat back) 630 x 450mm including fixing granit top with ceramic under counter basin pinning in ends of brackets or erecting stand including fixing of waste pipe and etc ( Suppy of pillar tap and waste pipe shall be measured separately) complete all as specified and directed.

M&L 32 mm bore Waste fittings, brass, chromium plated for glazed ware sinks, basins,glazed ware wash basin etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply only pillar tap 15 mm bore Single Lever Basin Mixer hot and could without Popup Waste with 450mm Long Braided Hoses

S & F Pillar taps,15 mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed fancy type complete all as specified and directed. .

S & F Angular Stop Cock with Wall Flange 15mm bore dia, cast copper alloy fancy type jaqwarKUP-35053PM

S & F stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs complete all as specified and directed.

S & F 32 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 PVC bends including all necessaryfixed complete to walls, ceilings or in floors etc.

M&L bib tap brass 15mm bore dia chromium plated long shank fancy type 2-way Bib Cock with Wall Flange screwed for iron pipes complete in repairs complete all as specified and directed.jaqwarFUS-29041

M&L bib tap ,15 mm, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.

S&F in repairs brass chromium plated bathroom wall (wall mounted model) mixture with telephonic shower arrangement with swivel wall hook with and including old Victorian design telephone shower with 12mm dia 1.5m long flexible tube and swivel hook etc. make- Jaguar (Cat No- 7217 & 9537) of catalogue or equivalent complete all as specified and directed.

S&F in repair 25 mm fancy type decorative stainless steel double curtain road with double bracket suitable hanging multiple sets curtains together for window and door including 02 nose double bracket and 04 nose fancy type rod for each window make- Vist,Marvel,mac decor ,decl or equivalent complete all as specified and directed.

S&F 25mm dia, fancy type decorative, aluminium curtain rod complete all as specified and directed. Make- Vista, Marvel, Mac décor, Deck.

S&F brackets and Nobs for 25mm dia, fancy type decorative, aluminium curtain rod complete all as specified and directed. Make- Vista, Marvel, Mac décor, Deck.

S&F Bottle trap of PTMT having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms)

S&F in repair, water jet chromium plated for vitreous china pedestal pattern water closet of approved make all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. ®

S&F in repairs brass chromium plated towel rail 20mm dia, "D" type, 600mm long between flanges.

S&F stainless steel soap dishes approximate size 160mm x 160mm x90mm as complete as specified as directed by Engineer-in-Charge.

S&F Glass Assembly sheet glass consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracked guard and railing 60cm long in repairs complete all as specified and directed..

S&F Brass chromium plated shower rose 125mm size including fixing to steel pipe or union in repairs complete all as specified and directed.

S&F 20 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed

S&F 25 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed

Taking down 100 mm cast iron soil waste pipe (any size or patterns) moulding all fittings heads, shoes, bends etc. (Measured over all as fixed along the confrce line over fittings and accessories).

S&F 100mm dia CI spun cast iron pipe jointed with cement joint and fixed to walls including cutting of holes wherever required complete all as specified and directed.

S&F 100mm dia CI bends including cutting of holes complete all as specified and directed.

S&F 100mm dia CI branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches and cutting of holes with cement joints complete all as specified and directed.

S&F CI cowl 100mm dia complete all as specified and directed.

S&F 75mm dia CI spun cast iron pipe jointed with cement joint and fixed to walls including cutting of holes wherever required complete all as specified and directed.

S&F 75mm dia CI bends including cutting of holes complete all as specified and directed.

S&F 75mm dia CI branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches and cutting of holes with cement joints complete all as specified and directed.

S&F CI cowl 75mm dia complete all as specified and directed.

Taking down AC rain water pipe any size or pattern incl all fittings heads, shoes, bends. Swan necks, etc including cleaning for refixing or removing to store.

M&L for 110 mm dia PVC (SWR) pipe single socketed (ISI marked) fixed fixed to wall with mild steel clamps complete all as specified and directed.

M&L PVC (SWR) 110mm bends any radiusequal complete all as specified and directed.

M&L 75 mm ,PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L 75 mm) PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed.

Chipping, removing, carefully concrete including loose palster by low impact Hammer without damaging the structure and cleaning and disposal of debris out side the premises including necessary form work ie providing & erecting steel props, safety nets, dust control net, Self supported two legged B class tubular steel scaffolding , 4mm thick ply covering to machineries / other utilities etc complete all as specified and directed.

Cleaning the existing reinforcement with wire / rotary wire brush, making the surfaces free from loose material dirt etc, complete. Applying two coats of alkaline rust converting primer conforming to ASTM-B- 117, on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 1 hour between the coats.

Providing and fixing additional steel bar in various structural elements like column, beams and slab etc including drilling, bending and fixing the bars tying with preleft binding wires etc complete anchoring reinforcement bar in existing RCC member in holes of minimum 10d depth for 10 mm dia bars complete all as specified and directed.

M&L for carrying out application of 'Bi-polar migratory corrosion inhibitor' EPCO-KP-100 on concrete surface. This inhibitor has migratory kind of propertyh which permits the material to migrate to a virtual extent of 100mm, through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It has property to attach anode as well as cathode, which is purely alkaline in nature (pH-9.5), so it has no carcinogen activity with concrete.

M&L for applying Anticorrosive Treatment to Reinforcement by IPNET RB. Application of two coats of IPNET RB on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be by brush complete all as specified and directed.

Providing and applying structural grade epoxy-latex bond coat pririor to application of any type of mortar conforming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete & new concrete by brush application complete all as specified.

Building up the profile of structual members by using polymer modified mortar upto 20mm thickness including levelling profilling etc complete all as specified and directed.Make:- Molith PMM of Krishna conchem or equivalent.Note :- Mode of measurement : Superficial area of concrete will be measured.

Building up the profile of structual members by using polymer modified mortar upto 40mm thickness including levelling profilling etc complete all as specified and directed.Make:- Molith PMM of Krishna conchem or equivalent.Note :- Mode of measurement : Superficial area of concrete will be measured.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 40mm in thikness) with prebatched, prepacked, single component ready to use microconcrete from M/s. Krishna Conchem (Molith MC) or equivalent of Dr. Fixit as approved by GE at any level and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications complete all as specified and directed.(Note : Reinforcement only shall be measured and paid separately).

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Providing precast cement concrete 1:2:4, type B1 (20 mm graded aggregate) set in CM 1:6, as in cover slabs (for manholes etc) with plain fair faces, all as spd.pd.

M&L Providing, cement concrete 1:2:4, type B0 (12.50 mm graded aggregate) in lintels upto 1.5m clear span hand wash counter wuthout base , cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by engineer in charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by engineer in charge.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick in ridges of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified and directed by engineer in charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channelor flat sections) including distance pieces, cleats etc. etc and similar work confirming to Fe-290 Gde E-165. complete all as specified and directed by engineer in charge.

S&F rolled mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and countersunk) forming holes, without any attachment, Fe 410-W (Gde-E-250) quality-B, complete all as specified and directed.

S&F in repairs stainless steel sink with drainage board made of stainless steel 1mm thick kitchen or labouratory with plugs, washers, and wastes. including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm and bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste, pipe complete all as specified and directed. Make : Nirali, Bule star ISI marked.

M&L sink Cock tab Pull –out kitchen taps with rinsing spray out pull out tops feature two spray a wide rinsing spray and regular spray stainless steel flexible 360 degree rotation 2 modes water saving faucet for kitchen sink / water faucet spray /flexible tap extension for kitchen sink item (Minimum weight 500 gms/ LxWxH 32x8x8 cm in repairs complete all as specified and directed.

S& F readymade pulley operated clothes drying system incl of four aluminium pipes of 9 feet long each (4pipes) channel assembly locking system ropes and all fixing material complete all as specified and directed . Make Easy Dry or equivalent make aas approved by CE Southern command Pune

Dismantling of boarding ,any description and in any position complete all as specified and directed

S&F for providing and fixing stainless steel (Grade 304) stainless steel hinges, handles, Stainless steel baskets, stainless steel rollers, Stainless steel hinge Italian patter suitable for cabinet and shelves opening / closing operation , Stainless steel perforated cutlery basket of suitable for cabinet,drawers and shelves opening / closing operation. Stainless steel steel Cup and Saucer basket suitable size of cabinet,drawers and shelves opening / closing operation. Stainless steel designer basket suitable size of cabinet,drawers and shelves opening / closing operation.Stainless steel designer basket suitable size of cabinet,drawers and shelves opening / closing operation Stainless steel designer basket suitable size of cabinet,drawers and shelves opening / closing operation stainless steel roller of size 25mm x 12mm, 505mm lenth suitable for baskets stainless steel vent perforated 1mm thick of size 150mm x 100mm Make-Syntex Plasto board and equivalent approved by Engr in charge. including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts hing roller ext. and bolts complete, stainless steel bolts etc., of required size,

Supply, fabricate and fixing with WPC board, one side decorative lamination and other side balancing white,100% termite proof,water proof,fire retardant, 18mm thick heavy density, interior grade cutting , fabricating and suitable fixing for kitchen cabinets and shelves of any size drawers openable leaf complete including fixing only accessories such as Italian stainless steel hinges, handles, magnets as required etc complete all as specified and directed as under :- (a) Stainless steel Handle fancy type 100mm size. (b) Stainless steel hinge Italian patter suitable for cabinet and shelves opening / closing operation. (j) Magnet of suitable size fixed for cabin leafs, drawers Make-Syntex Plasto board and equivalent approved by Engr in charge. Note- The rate includes WPC board and all connecting items mentioned above and The design and pattern should be approved by Engr In Charge.

Exavating in trenches in Hard / dense soil n. exe 1.5 m wide and n. exe 1.5 m in depth, for foundation etc or for shafts, wells, cess pits, man holes, pier holes etc n exe 10 sq m on plan n exe 1.5 m depth and getting out complete all as specified and directed

M & L for cement concrete 1:4:8 type D-2, using 40 mm graded stone aggregate as in foundation complete all as specified and directed.

S/F 200mm bore salt glazed stone ware drain pipes laid in trenches and jointed as specfied complete all as specfied and directed.

M&L for concrete bed in cement concrete 1:3:6 type C2 to drain pipes of 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specfied and directed.

Returning, filling in Hard / dense soil , including spreading, levelling, watering and well raming in layer not exe 25cm complete as specified and directed.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed of material ourside MD land complete as specified and directed.

Cutting into existing man holes for connecting new drains of 150mm dia pipe and making good two pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 and finished and reforming benching as required complete all as specified and directed.

M&L Solid PVC color coated Wall Panel Lining consisting of 5mm thick inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L for providing stages wise waterproofing treatment to sunken portion of toilets as under. Stage 1: Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debries outside MD land etc complete all as specified and directed. Stage 2: Providing 15 mm thick plaster in CM 1:3 mixed with integral water proofing chemical of STP Ltd in the proportion /quantity all as per manufactures instructions. Stage 3 : Primer - Mix Tarfelt LM with water in ratio 1:1 @ 250 gms/sqm and apply the primer on the plaster surfaces Stage 4 : Application of 1 st coat of Tarfelt LM of STP Ltd without dilution with water@1kg/sqm by brush all as per manufactures instructions. Stage 5: Laying 50 GSM fyber glass cloth over the 1st coat while the coated surface is still tacky Stage 6: After 6 to 7 hours interval apply second coat i.e final coat of Tarfelt LM without dilution with water of STP Ltd by brush as per manufactures instructions.@1kg /Sqm Stage 7: Providing 10mm thick protective plaster in CM 1:3 mixed with STP NO -1 @ 250ml/50kg cement all as manufactures instructions.

M&L for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed

S&F of Aluminium composite panel (ACP) of 4mm thick sheet coated mirror glossy finish/ Natural wood finish of approved colour, pattern & design & as required shape like rectangular, trapezoidal or tapered curved shape (colour, shade, texture as per sample kept in GE office) with Poly Vinylidene Fluoride (PVDF) of flat panel that consist of two thin aluminium sheets (0.5mm thick) bonded to a non-aluminium core of flat sandwich panel is a structure of three layer aluminium core bonded between two sheets of required size fixed with heavy duty screws on aluminium chanel rectangular section of size 38mm X 25mm thickness 2mm for vertical & horizontal frame work or equivalant section with respect to weight, and used for external cladding or facades, partition, false ceiling, signage, Chajjas etc. The joints to be filled with silicon seelant of translucent, white or black in colour with the help of portable punch machine work pneumatically after cutting the carners and edges. A protective film on ACP is removed after installation including necessary scaffolding complete all as specified and directed

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F premoulded FRP Chajjas with 2 to 2.5 mm FRP thickness on both sides with manglore clay type finished with 150 mm drop on front, sides and 60 mm collar on back side including including necessary scaffolding necessary fixtures complete all as directed.

M&L Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 toends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth complete all as specified and directed

M&L Cutting grooves in brick wall, 100 mm wide and 150 mm deep and shaping , filling cement concrete 1:2:4 type B-l in cement mortar 1:3 making good to facings where required complete all as specified and directed (Note :- Supply only Shali Crete (Acrylic polymer Coating) water proofing shall be measured & paid separately).

Supply only Shali Crete (Acrylic polymer Coating) water proofing compound.

M&L Demolition of cement concrete any face internal /external unreinforced of any type any level and at any position Ensure that structure is at least 3 days old, Bonding Agent Bond coat with a mixing ratio of 1:2 (one part of ShaliCrete® and two parts of cement). The applied bonding agent should be in tacky condition before topping. Repair Mortar Bond coat with a mixing ratio of 1:2 (one part of ShaliCrete® and two parts of cement) including 10mm Repair Mortar with a mixing ratio of 1:2:4 (one part of ShaliCrete®, two parts of cement and five part of sand) applied in specified area.• After the application of Repair Mortar to keep the surface moist for 12 - 24 cement complete all as specified Note : Shali Crete (Acrylic polymer Coating) .a shall be measured & paid seperately.and including necessary scaffolding complete all as specified and as directed.

Taking down carefully copper/alumunium point wiring for light, fan, bell, socket or power complete including fittings such as switches, ceiling roses pendents regulators, sockets and tube light fittings etc, removing materials from site or for reuse refixing and making good distrubed surface of wall, floors etc all as specified and directed.

Taking down main switches DBs with sheet metal enclosure 2/4/6/8 way SPN/TPN/DBs,Meter Boxes etc all as specified and directed.

Taking down of existing ceiling fans, opening / dismantling of fan& fan blades, cleaning, servicing,oiling, greasing, carrying out repairs such as replacement of capacitors, bearings, bushes, canpoy, condensor, clamp, safety pin, rubber bush and reassembling the fan & fan blades,, connecting up, testing and re-fixing of the same ceiling fan of any sweep including provision of new cable from ceiling rose/ connector to fan and spray painting of ceiling fan with two coats of synthetic enamel paint after prepartion of surfaces,complete all as specified and directed

Taking down of existing exhaust fan 300 mm size (12") A C single phase 230 Volt and deposting the same to MES store yard complete all as specified and directed

M & L for point wiring complete with proper colour coding using 1100 volts grade, 1.5 Sqmm, PVC insulated, FRLS,unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked, drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good the same in CM 1:3 to match with existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, also including1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts mutli-stranded copper conductor green colour as continous earth wire connected to common earth dolly all as specified and diretced for one light point/fan point controlled by one one way switch, complete all as specified and directed

-ditto- all as per item No 174.00 above but for one 5 pin socket 5 Amps on same board complete all as specified and directed

-ditto- all as per item No 174.00 above but for one 5 pin socket outlet 05 Amp independent board complete all as specified and directed

-ditto- all as per item No 174.00 above but for one bell point controlled by 5 Amps bell Push complete all as specified and directed.

M & L for point wiring complete with proper colour coding using 1100 volts grade, 2.5 Sqmm, PVC insulated, FRLS,unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked, drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good the same in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc. also including 2.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts mutli-stranded copper conductor green colour as continous earth wire connected to common earth dolly all as specified and diretced for one 5Pin,6/16Amps,Socket outlet independent,complete all as specified and directed

M & L for point wiring complete with proper colour coding using 1100 volts grade,4.0 Sqmm, PVC insulated, FRLS,unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked, drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good the same in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc. also including 4.0 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts mutli-stranded copper conductor green colour as continous earth wire connected to common earth dolly all as specified and diretced for A.C Point Metal Socket outlet independent,complete all as specified and directed

Telephone wiring complete with 0.40 Sqmm nominal area PVC flexible telephone core solid copper conductor cable unsheated in and incld concealed non metalic rigid PVC conduit 20mm dia ISI marked incld fittings acceories and incld sunken MS terminal box suitable for mounting Telephone shocket 2 pin complete all as specified with 3 mm thick Ms plastic sheet cover all as specified and directed.

Supply & Fix Three pin Plug & Socket with Plastic enclosure with 2 pole and Eathing for incorporating 20 A SPN MCB For A.C Control Make :Havells Cat part No.- DHDCUSN020 or Equivalent of Legrand/Standard/Siemens

Supply and fix in replacement of call bell AC, 230 Volts single pole all as specified and directed.

Supply & fixing ceiling rose , surface bakelite 3 terminal complete .

Supply & fixing modular fan regulator,120W- 2 module

Supply & fixing switch modular type 6 Amp single pole one way 230V completed

Supply & fixing switch modular Bell push 6 Amp single pole one way 230V completed

Supply & fixing switch modular type 16 Amp single pole one way 230V completed

Supply & fixing socket modular type 6 Amp 2/3 pin single pole one way 230 V complete

Supply & fixing socket modular type 16 Amp 2/3 pin single pole one way 230 V complete

Supply & fixing Modular white cover plate with frame 8 Module

Supply & fixing Modular white cover plate with frame 3 Module

Supply & fixing Modular white cover plate with frame 2 Module

Supply & fixing modular Metal Flush box 8 Module

Supply & fixing modular Metal Flush box 3 Module

Supply & fixing modular Metal Flush box 1/2 Module

Supply and fixing integrated sleek extruded LED channel with acrylic cover 20 watt with white light having, Lumens shall not be less than 90 luments / watt, P.F >0.95 correlated colour temp (CCT)-6500k. Driver efficiency 88%, starting voltage 90V, THD< 20, colour rendering Index (CRI) > 80, luminaries complies the BIS and ISI safety norms and including with driver and prewired complete including 0.5 sqmm 3 core flexible wire connecting from ceiling rose complete all as specified and difected. Make :Havells Cat No. LHEXBLP7PN1W020 /Crompton/Philips/Wipro.

Supply and fixing integrated sleek extruded LED channel with acrylic cover 10 watt with white light Luminours efficiency shall not be less than 90 lumens/watt, P.F >0.95 correlated colour temp (CCT)-6500k. Driver efficiency 88%, starting voltage 90V, THD< 20, colour rendering Index (CRI) > 80, luminaries complies the BIS and ISI safety norms including with driver and prewired complete including 0.5 sqmm 3 core flexible wire connecting from ceiling rose complete all as specified and difected. Make :Havells Cat No. LHEXACP7IN1W010 /Crompton/Philips/Wipro.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply & fix exhaust fan 300 mm sweep, 1200 rpm, 230V complete with louvers, Plastic body, bolts, nuts, washers, suitably embedded in wall(include wall cutting for hole) with provisioning of 23/0.0076 flexible three core wire for electrical connections from ceiling rose to fan all as specified and directed. Make : Crompton/Havells/Bajaj

Supply and Fitting Curved glass wall mounted type stainless steel T-Shapped Kitchen Chimney with baffle filter of air Suction Capacity 1200 Cum/Hr thermal Auto clean operated with single phase 230 V,50Hz A.C Supply Complete all as specified and directed by the Engineer-in-charge.Make : Hindware Nevio 90 or any equivalent Specification of Crompton/kaff as aprroved by the G.E.The specifications required for the above chimney following below are. (i) Chimney width : 90Cm (ii) Air Suction cxapacity : 1100-1200 cum/hr. (iii) Body type : Stainless stee/black painted Glossy finish. (iv) Control : Soft push button. (v) Smoke Exhaust pipe upto kitchen window Length required not less than 02 Mtrs. Note : product warrenty shall be minimum 01 Year and Motor warrenty shall be 05 Year.

Taking down old unserviceable submain cable of any size and capacity and finishing wall surfaces.

M&L for sub main wiring complete two run of size 1.5 sqmm PVC insulated ,unsheathed, heavy duty 1100 volts grade (FRLS) multi-stranded copper conductor cable ,drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continous earth wire connected to common earth dolly and mains, complete all as specified and directed.(For Building security Lights) Note: Three run 1.5 Sqmm PVC cable and one run of Casing Caping & conduit will be measured as "one unit"length.

M&L for sub main wiring complete Two run of size 10 sqmm PVC insulated ,unsheathed, heavy duty 1100 volts grade (FRLS) multi-stranded copper conductor cable ,drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 10 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continous earth wire connected to common earth dolly and mains, complete all as specified and directed. Note: Three run 10 Sqmm PVC cable and one run of Casing Caping & conduit will be measured as "one unit"length.

Ditto all as same above item No 210.00 but for Sub Main wiring Three Run 4.0 sqmm

Supply & fix sheet metal enclosure powder coated for MCB DB SPN 12 way double door with din rail and bus bar including making good to the disurbed surface matching with the existing complete alla s specified and directed. Make :Legrand/Schnider/Heger/ABB

Supply and fix MCB SPN 240 volts 40-63 Amps breaking capacity 10 KA 'C' Series rating complete all as specified and directed. Make : Legrand/Schnider/Heger/ABB

Supply and fix MCB SP 240 volts 6 to 32 Amps breaking capacity 10 KA 'C' Series rating complete all as specified and directed. Make : Legrand/Schnider/Heger/ABB

S & F LED light fitting 10Watt bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make : Jaquar/Bajaj/Wipro

Supply and fixing in replacement of double door type hot press moulded meter Junction box suitaible for 10,12 & 16 single phase meter all as specified and directed. Make : Sintex or any equivalent Make : Legrand/Schnider/Heger/ABB

Material and labour for earthing complete with GI earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground lavel) with top edge of the plate not less than 1.5mtr below normal ground lavel connected to GI earth strip 32X6 mm by mean of bolts, nuts, check nuts and washer of brash all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit and CI cover fullel with watering pipe, wire mess and copper lugs etc GI protection pipe 40 mm dia medium grade including testing on completion all as specified and directed.

R.C. Magla and Co.

C S Sharma and Co

KAJAL CONSTRUCTION

Vishal Builders