SPECIAL REPAIR TO BUILDING NO P 10 POST OFFICE, MH 01 01, MH 01 02, MH 02 01 AND MH 02 02 INCLUDING CONNECTED EM WORKS UNDER AGE BR II IN GE CENTRAL BANGALORE

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete as directed. (measured flat overall)

Dismantling timber fillets,rails, post, rafters, purlins etd under 40 Sq.cm in section (framed work), in any position complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD land complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debris out side MD land complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding etc) and removing debris outside MD land complete all as specified and directed.

Demolition of reinforced cement concrete any description and in any position not otherwise specifically provided for etc, cutting reinforcement steel to facilitate demolition of concrete including removing the materials out side MD land complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Demolition of soil/waste pipe (PVC pipe) of any dia including fittings complete all as specified and directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down shutters, exceeding 1.0 sqm but n.exc. 2 Sqm in each and refixing shutter in the same opening including easing & adjusting complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F second class hard wood fillets, wrought, square rectangular or triangular in section secured with nails, cross sectional area exc 13 and not exc 25 sqcm etc including two coat of painting using synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F second class hard wood scantling, clean sawn timber fixed with nails etc complete all as specified and directed.

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints including treating the timber libarally brushed at least twice with oil or kerosene based solusion of chlorophyrifos 20EC 1.0 % (by weight) concentration complete all as specified and as directed.

S & F 35 mm thick, second class hardwood glazed and skeleton shutters as in windows/ventilators open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded complete all as specified and directed in SSR Part I Section 8 clause 8.24 (a).

S&F 35mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F 4 mm thick, Figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 75 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 100 mm size, butt hinges, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 125 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F Rolled mild steel work as in trusses, purlins, posts rafters etc using Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S & F band, straps, supports or stays for rainwater pipes, ventilating pipes, including bolts if required hooks (stay), heavy duty, for large gate, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and the similar small articles conforming to Fe-290 Gde- E-165 all as directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for 100mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of floor, etc complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, level course etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 8 to 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.36 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for ceramic, coloured tiles 7 to 8 mm thick as in skirting to match the length of floor tile procured under No 16 above including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles joint free tiles 350x250x 7mm/450x350x7 mm thick as in Dado/Skirting/Steps/vertical surfaces including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for precast cement concrete solid building blocks, 1:3:6, type C-1 (using 20mm graded stone aggregate) or slab 10 cm thick (with plain or interlocking joints as directed) setting in cement mortar 1:4 complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

M & L for Plain cement concrete 1:2:4, type B-1, (using 20 mm graded stone aggregate) as in roof kerb, coping, kneelers, bed plates, filling to gap between roof sheet and wall etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

S & F TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F TMT steel bars 6 to 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for raking out joints/ pointing to squared rubble masonry,coursed or uncoursed built in cement mortar, cutting out joints and decayed mortar, not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surfaces wet for 2 days prior to re-pointing complete all as specified and directed.

M&L for raised pointing to squared rubble masonry,coursed or uncoursed using cement mortar 1:4 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceilings and applying two coats of white wash complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, width or girth not exc 10cm and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of old or previously treated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for Preparation of old steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparing new plastered surfaces of walls and applying two coats of distemper-oil-emulsion over 1 to 2mm thick wall care putty, finished smooth over a coat of primer complete all as specified and directed.

M & L for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over 1 to 2mm thick wall care putty, finished smooth over a coat of primer complete all as specified and directed.

M & L for preparing old plastered surfaces of ceilings by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over 1 to 2mm thick wall care putty, finished smooth over a coat of primer complete all as specified and directed.

M & L for for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for removing existing water proofing treatment along with PVC sheets disposing out of MD land/premises and rendering 10mm thick in CM 1:4 mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions & Applying oil bound bitumen primer @ 0.40 Kg/Sqm and providing 3 mm thick APP membrane weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt weighing not less than 180 gm /sqm having softening point not less than 140 centigrade, having tensile strength of 650N/sqm and 350 N/sqm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap, applying a coat of blown grade hot bitumen 90/15 over the membrane @ 1.2 Kg /Sqm on top of membrane surface and then finished with solar reflective bituminious aluminium paint @ 0.10 Kg/Sqm complete all as specified and as directed.

Taking up or down 20mm bore, Steel tubing and connections.

Taking up or down 25mm bore, Steel tubing and connections.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head including taking down old unserviceible water tank of 1000 litre capacity complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head including taking down old unserviceible water tank of 1000 litre capacity complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply and fix CPVC ball valve suitable for 20mm dia COVC pipe complete all as directed.

Supply and fix CPVC ball valve suitable for 25mm dia COVC pipe complete all as directed.

S&F in Repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, providing Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & 32 mm dia LDPE PVC waste pipe, PVC connection 15 mm size 600 mm long including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge.

S & F Vitreous China urinal, bowl type, flat back, size 465X355X265mm (Appx size), white with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, 32mm dia waste pipe including 450mm long PVC connection and 15mm size CP push tap complete complete as specified and directed. (Make: Parryware /Hindware/Cera/Prayag)

S&F in Repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long and 32mm dia flush pipe, S or P Trap & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge.

S & F vitreous china urinal partition plate, white, 330X675 mm all as directed. Make: Parryware Cat No C0507 or equivalent of make CERA/Hindware/PRAYAG

S&F in repair 15 mm bore bib taps cast copper alloy chromium plated with capstan head screwed down to iron pipe, fancy type complete all as specified and directed

S&F in repair 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S & F towel rail, 600 mm long of PTMT fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed. (Minimum weight 190 gms).

S & F swivel shower with shower arm 225mm long of PTMT, any colour, suitable for 15/20mm pipe fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed. (Minimum weight 40 gms). Make PRAYAG Cat No 181 for shower & 184 for arm or equivalent of other make as approved by GE.

S & F shelf 18 inch long of PTMT, any colour, fixed with and including chromium plated brass screws in wooden/plastic cleat or rawl plug complete all as directed. (Minimum weight 300 gms). Make PRAYAG Cat No 191 or equivalent of other make as approved by GE.

S & F in repairs PVC connection pipe with PTMT nuts, 450mm long. Make: CERA/Hindware/Parryware/PRAYAG

Cutting into existing manholes for inserting new drain pipe, 150mm bore and making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B1 finished to match with existing complete all as directed.

All as per item No above but for removing existing branch drain, making good to walling and rendering, cutting out branch channel and making good benchings complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggragate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore SGSW drain pipes complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as surface channels and drains complete all as specified and directed.

S&F 110 mm dia UPVC (SWR), Type 'B', soil waste pipes single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S&F 75 mm dia UPVC (SWR), Type 'B', soil waste pipes single socketed,in any length with rubber ring joints,laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S&F UPVC (SWR) junction single,(single T) 75 mm with access door complete all as specified and directed.

S&F UPVC (SWR) junction single,(single T) 110 mm with access door complete all as specified and directed.

S&F UPVC (SWR) vent cowl suitable for 110 mm dia pipe.

S & F in repair 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 75 mm dia outlet , PVC (SWR) multi floor trap, with grating including jointing to waste pipe with solvent cement, fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring surface type, with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC conduit 'medium grade' conforming to IS-9537 with all fittings and accessories (like Tee, bend etc.) complete in walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point and earth dolly including MS/PVC terminal box with 3mm thick masonite laminated sheet top cover fixed on wall with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed.

All as per item No 91 above but for one 3 pin socket outlet, 5 Amps on Independent board complete all as specified and directed.

All as per item No 91 above but for one 5 Amps, 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No. 91 here in before but wiring with cables of size 2.50 sqmm for wiring & cables of size 2.50 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 6 pin Switch/Socket outlet on Independent board complete all as specified and directed.

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F Switch socket combination, 2 in 1, 5 Amps (bearing ISI marked), flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps (bearing ISI marked), 240 volts, flush type complete all as specified and directed.

S & F Ceiling rose, 3 phase/PVC/polycarbonate (bearing ISI marked), isolated body including providing PVC square/round block complete all as specified and directed.

S & F Stepped type(five steps) electronic fan regulator flush type complete all as specified and directed. (Make: Anchor, Model No. 14502 or equivalent make as per list of manufacturer)

M & L for Sub main wiring with two runs of 4 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through/in and including PVC conduits, medium grade, of suitable size, fixed to wall/ceiling etc with all accessories, fittings, fixures including 4 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

M & L for Sub main wiring with two runs of 6 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through/in and including PVC conduits, medium grade, of suitable size, fixed to wall/ceiling etc with all accessories, fittings, fixures including 6 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with 200 Amps rated bus bar neutral link, earth bar and din rail, TPN, 6 way (8+18), 415 Volts IP-43, IK -09, suitable for housing MCB's fixed flush in wall complete all as specified and directed.

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with common bus bar neutral link, earth bar and din rail, SPN, 4 way, 240 Volts IP-43, IK -09, suitable for housing MCB'sfixed flush in wall complete all as specified and directed.

S & F Factory made distribution board (DB), Double Door in sheet steel enclosure fitted with common bus bar neutral link, earth bar and din rail, SPN, 8 way, 240 Volts IP-43, IK -09, suitable for housing MCB's fixed flush in wall complete all as specified and directed.

S & F MCB, four pole 63 Amps, 415 Volts, 'C' Series, 10KA breaking capacity complete all as specified and directed.

S&F Modular thermoplastic box of size 250X250X160mm with locking arrangement, hinged door, suitable to accomodate single phase meter fixed on PVC box of suitable size on wall complete all as specified and directed. (Make - Sintex, CAT No : GSMB 2525 or equivalent model of make as per list of manufacturer attached).

S & F MCB, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

S & F MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA breaking capacity complete all as specified and directed.

Cutting hole/opening through stone masonry wall of 38cm thick suitable for providing 300mm sweep exhaust fan and making good the disturbed surfaces using cement mortar 1:4 or PCC 1:2:4, type B1 as required including toothing and bonding, finished the surfaces to match with existing ie white/colour wash as required complete all as directed.

Supply and Fixing exhaust fan, 300mm sweep, AC single phase 230/240 Volt including louver cut to fit with hole for exhaust fan complete all as directed.

Taking down ceiling fan/exhaust fan and applying one coat of painting at site using synthetic enamel paint using spray painting machine after cleaning properly including provision of suitable size twin core copper cable connecting up with ceiling rose, replacing 2.5/3.15 MFD capacitor, canopy, bearing, bush, rubber bushing, screws, bolts, nuts etc and greasing complete all as directed.

M & L for rewinding of ceiling fan using appropriate size of copper enamrlled wire including varnishing heating with proper insulation including testing complete all as directed.

M & L for hook/clamp for hanging of ceiling fanfabricated out of 40X6mm Mild steel flat iron made to shape as required, fixed on angle iron truss/GI tubing member using necessary bolts, nuts, rubber bushing and washers including two coats of painting over a coat of primer complete

S&F LED tube light fitting of 20 watts 6000K , 230 volt, basic all purpose surface and wall mounted type with polycarbonate housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and providing & connecting up with twin core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Cat No LUMILINEBS20WIED830SPCWH or equivelent of Philips/Crompton Greaves/Bajaj

S&F energy saving environmental friendly long life, with high power LED building security light 1x 15 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 and wired with all accessories and connection up with and including 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make: Havell's Cat No. ENDURAPEARLSL15WLED757SASYTOPC or equivelant of make

S&F security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

M & L Earthing complete with Galvanised steel earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete inclduing taking down old one as specified and as directed.

Supply and laying cable UG XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10.00 Sqmm 2 core including alumunium lugs etc for connecting and taking out old one complete all as specified and directed. (Note: Excavation and earth work shall be measured and paid seperately)

Supply and laying well burnt bricks, sub class 'B' bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply, laying, 40mm bore, Steel water tubing, galvanised, light grade with all fittings and fixtures for cable protection on road/drain/floor or for hangging ceiling fan etc including providing MS clamp, bolt, nuts complete all as specified and directed.

HRML CONSTRUCTIONS

D NAGI REDDY