REPAIRS TO JOINERY FLOORING AND CERTAIN MISC B AND R ITEMS TO OR MD ACCN AT GORKHA CAMP UNDER GE WELLINGTON

Amount

Demolition of Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

Plain cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring 25mm thick all as specified and directed.

Coloured Glazed ceramic tiles in vertical surfaces 450 x 350 x 7 to 8mm / 600 x 300mm x 7 to 8mm thick, as in dado, skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigments to match the surface, over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. Note: Colour and shade of tiles shall be approved by GE and contractor shall not have any claim whatsover on this account.

Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and directed.

Coloured non - skid Ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including Screed bed or bedding layer 15mm thick in CM 1:6 complete all as specified and as directed.

Coloured non - skid Ceramic tiles 7 to 8 mm thick (Square / Rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm as in skirting (width not exceeding 15cm), set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with white cement and pigment over and including 15mm thick screed in cement mortar 1:4 all as specified and directed.

75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of flooring complete all as specified and directed.

Chequered cement bullnosed tiles 32cm x 20cm x 30mm thick as in treads, set and jointed over and including 20mm thick screed bed in cement mortar 1:6 and pointed in cement slurry complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

Rendering 20mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair face of brickwork finished even and smooth without using extra cement all as specified and directed

Rendering 20mm thick in cement mortar 1:4 finished even and smooth without using extra cement on stone walls and above chajjas all as specified and as directed. Note: Rate quoted is deemed to be inclusive of necessary scaffolding required for plastering.

Rendering 5mm thick in cement mortar 1:4 on concrete surface in ceiling all as specified and directed

Applying three coats of white wash on newly plastered ceiling surfaces including preparation of surface complete all as specified and as directed.

Applying two coats of oil bound distemper on old plastered surfaces including preparation of surfaces all as specified and directed.

Complete removal of existing treatment on old wall surfaces and applying two coats of oil bound distemper over a coat of primer and 2-3mm thick putty all as specified and directed.

Applying two coats of cement base paint, over a coat of primer including preparation of newly plastered surfaces complete all as specified and as directed.

Applying two coats of cement base paint, over a coat of primer including preparation of old plastered surfaces complete all as specified and as directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint all as specified and as directed.

Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

75mm thick Cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate as in plinth protection / path way finished even and smooth without using extra cement all as specified and directed.

Forming contraction (dummy) joints, 65mm deep, 10mm wide filled with sealing compound grade 'A' all as specified and directed.

PCC 1:3:6 type C-2 using 40mm graded stone aggregate in surface channels and drain complete all as specified and directed

Forming fair finished drain or channel of 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred / stopped ends etc all as specified and directed

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sq m on plan and not exceeding 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Salt Glazed stoneware drain pipes of 150mm internal dia, grade 'A' laid in trenches and jointed in cement mortar 1:1 mixed with spun yarn and testing complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of the pipes after they are laid and tested in cement concrete 1:3:6 type C-2 using 40mm graded aggregate complete all as specified and directed. Note: Thickness of the concrete bed shall be 100mm

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each, complete all as specified and directed

Removing excavated soil/ material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Cutting into existing manholes for connecting new drains of 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm dia all as specified and directed

Taking up or down steel tubing and connections for 20mm dia all as specified and directed

GI pipe 15mm dia medium grade with all fittings fixed on wall, ceiling or laid in floors complete all as specified and directed.

GI pipe 20mm dia medium grade with all fittings fixed on wall, ceiling or laid in floors complete all as specified and directed.

Ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed in repairs of 20mm dia all as specified and directed.

Gunmetal globe or gate valves with iron wheel head screwed both ends for iron pipe of size 20mm dia fixed in repairs all as specified and directed.

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, fixed to walls, with PVC clamps complete including taking down existing unserviceable PVC(SWR) pipes all as specified and as directed.

PVC (SWR) 75mm dia bore pipe single socketed in any length, with rubber ring joint fixed on wall with PVC clamp complete including taking down existing unserviceable PVC(SWR) pipes all as specified and directed.

PVC (SWR) bend of any radius 75 mm dia all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia all as specified and as directed.

PVC (SWR) floor trap 75mm outer dia, plain with grating including jointing to waste pipe with solvent cement fixed in repairs all as specified and as directed.

PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete in repairs all as specified and directed.

PVC (SWR) branch piece single, (single Y) equal or un equal of 110 mm bore of pipe complete all as specified and directed

PVC (SWR) branch piece double, (double Y) equal or un equal of 110 mm bore of pipe complete all as specified and directed

PVC (SWR) junction single, (single T) equal or unequal of 110 mm bore of pipe with access door complete all as specified and directed

Vitreous china wash hand basin, white flat back size 550 X 400 mm excluding taps, waste, chain and plug and procelain stopper but including brackets and waste pipe with waste coupling including cutting for and pinning in ends of brackets or erecting, fixed in repairs complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including connection to trap and flushing pipe, anti syphonage pipe, etc. complete including making good to floor fixed in repairs all as specified and directed.

PVC low level flushing cistern 10 lts capacity, valveless, syphonic action type, (white coloured) with inlet ball valve, float and handle including PVC fixtures, flush pipe etc, fixed in repairs complete all as specified and directed.

PVC connections 15mm size with PTMT nuts and washer of length 450mm all as specified and directed.

Bib taps,15 mm bore chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repairs all as specified and as directed.

Pillar taps, fancy type, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe fixed in repairs all as specified and directed.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type chromium plated ,15mm bore fixed in repairs all as specified and directed

Gratings 125mm dia with waste hole, of PTMT (min weight 40gms) fixed in repairs all as specified and as directed.

Stainless steel sink made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union to pipe, overall size 495mmx420mm with bowl size 410mm x 330mm x 160mm all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones all as specified and directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane all as specified and directed.

4 mm thick figured glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sq. m in each pane all as specified and directed.

Expanded metal, not exceeding 4 kg per sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed to wood or steel members complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking of shutters from the frames) area not exceeding 1.5 Sq mtr each all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutters from the frames) area exceeding 1.5 Sq mtr but not exceeding 4 Sq mtr each all as specified and directed.

Taking down Shutter of any description exceeding 1 sqm and not exceeding 2 sqm each all as specified and directed.

2nd class hard (sal / Hollock) wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue, pinned at joint all as specified and as directed.

35mm thick second class HW plain, framed, panelled shutters (any No of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers and fitted to chowkats all as specified and directed.

2nd class HW Glazed and skeleton shutters 30mm thick, for windows / ventilators divided in to squares, with plain, chamfered or rounded mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass,etc; size of members of shutters as specified in SSR part I, section 8, clause 8.24(a); supplied and fixed to existing chowkhats second class hard wood all as specified and directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing all as specified and directed.

Factory made solid panel PVC door shutter 30mm (Stile) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section 200 mm long all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section 150 mm long all as specified and directed.

300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

100mm long butt hinges medium weight cold rolled mild steel and fixed all as specified and directed.

Butt hinges, 75 mm size medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Aluminium handles, cast type, anodised 150 mm long complete all as specified and directed.

Aluminium handles, cast type, anodised 100 mm long, fixed in repairs complete all as specified and directed.

Rigid steel conduit for curtain rods 20mm external dia fixed in repairs complete all as specified and directed.

Taking down door Shutter exceeding. 1 sqm and not exceeding 2 sqm each and refixing in the same opening after necessary easining complete all as specified and directed.

Preparation of old steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in flooring and mass concrete 100mm thick all as specified and directed.

80mm thick interlocking reflective, rubberised tiles of M40 grade or equivalent all as per IS 15658-2006 including 50mm thick sand cushion, joints filled with grey cement and pigment all as specified and directed.

20-25mm thick machine cut cudappah stone slab over and including screed bed 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry with pigment to match the shade of the slab including rubbing and polishing all as specified and directed.

Dismantling of Wrought Iron or Mild steel work of any description not otherwise provided for complete all as specified and directed.

Kitchen Rack plate stainless steel of size 0.9mtr x 0.6mtr fixed to wall all as directed.

Applying a uniform coat of blown grade bitumen 85/25 @ 1.20 Kg per Sqm conforming to IS 702/cold applied bituminious elastomeric coat over a coat of primer @ 0.70 kg per Sqm on plastered surface in sunken floor including cleaning surfaces all as specified and directed.

APP modified prefabricated water proofing membrane, 3mm thick and weighing not less than 3.6 kg/Sqm as described under roof treatment laid on primed surface by forced application complete as specified in sunken floor all as specified and directed.

20mm thick cement mortar 1:4 screed mixed with liquid water proofing compound @3% as per manufacturers instructions over APP membrane in sunken floor all as specified and directed.

40mm dia light grade GI spout at the lowest point with 30cm projection beyond the outer face of the wall in sunken floor all as specified and directed.

Lean concrete 1:5:10 type E2 with 40mm graded stone aggregate with lime mortar 1:3 filling in sunken portion all as specified and directed.

sree devi construction

GMS Builders

AR Mohamed Yakub and Co

K BALUSWAMY