TSK DIV:- Augmentation of Capacity of Running Room/ Rest Rooms at MXN & JTTN.

Item- 1 CPWD items

S No. Item No Description of Item Unit Qty Rate Amount

1.0 CARRIAGE OF MATERIALS

By Mechanical Transport including loading,

unloading and stacking

1.1.18 Disposal of moorum/building rubbish/ malba/ cum 560 494.1 276696

similar unserviceable, dismantled or waste

material by mechanical transport including

1 loading, transporting, unloading to approved

municipal dumping ground for lead upto 10

km for all lifts, complete as per directions of

Engineer-in-charge.

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator) / manual

means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on

2.8 plan), including dressing of sides and

ramming of bottoms, for all lift, including

getting out the excavated soil and disposal

of surplus excavated soil as directed, within

a lead of 50 m.

2.27 Supplying and filling in plinth with sand cum 400 2123.75 849500

3 under floors, including watering, ramming,

consolidating and dressing complete.

Surface dressing of the ground including

removing vegetation and in-equalities not

exceeding 15 cm deep and disposal of

rubbish, lead up to 50 m and lift up to 1.5 m.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

TINSUKIA DIVISION-ENGINEERING/N F RLY

derived from natural sources : 4 graded

stone aggregate 20 mm nominal size

derived from natural sources)

derived from natural sources : 8 graded

stone aggregate 40 mm nominal size

derived from natural sources)

4.10S DAMP-PROOF COURSE

4.12 Extra for providing and mixing water per bag 1200 18.15 21780

proofing material in cement concrete work in of 50 kg

doses by weight of cement as per cement

manufacturer's specification. used

5.0 REINFORCEMENT CEMENT CONCRETE

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 350 392.15 137252.5

for mass concrete

5.9.3 Suspended floors, roofs, landings, balconies Sqm 470 927.25 435807.5

and access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 830 736.4 611212

bressummers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 750 961.3 720975

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Kg 18500 107.85 1995225

Fe-500D or more.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above

5.22A.6 Thermo-Mechanically Treated bars of grade Kg 29700 107.85 3203145

Fe-500D or more.

5.33S DESIGN MIX CONCRETE

Providing and laying in position ready mixed

or site batched design mix cement concrete

for reinforced cement concrete work; using

coarse aggregate and fine aggregate

derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag

c e m e n t , admixtures in recommended

proportions as per IS: 9103 to accelerate /

retard setting of concrete, to improve

durability and workability without impairing

strength; including pumping of concrete to

site of laying, curing, carriage for all leads;

but excluding the cost of centering,

shuttering, finishing and reinforcement as

per direction of the engineer-in-charge, for

the following grades of concrete.:

5.33.1 All works upto plinth level

5.33.1.1 Concrete of M25 grade with minimum cum 150 9504.75 1425712.5

cement content of 330 kg /cum

5.33.2 All works above plinth level upto floor V level

5.33.2.1 Concrete of M25 grade with minimum cum 250 9860.4 2465100

cement content of 330 kg /cum

6.0 MASONRY WORK

6.1S General

TINSUKIA DIVISION-ENGINEERING/N F RLY

Brick work with common burnt clay F.P.S.

6.1 (non modular) bricks of class designation 7.5

in foundation and plinth in:

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay

F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above

plinth level up to floor V level.

8.0 CLADDING WORK

8.1S General

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required size,

approved shade, colour and texture laid

8.2 over 20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching

pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to

edges to give high gloss finish etc. complete

Granite stone slab colour black, Cherry/Ruby

Providing edge moulding to 18 mm thick

marble stone counters, Vanities etc.,

8.3 including machine polishing to edge to give

high gloss finish etc. complete as per design

approved by Engineer-in-Charge.

8.5 Extra for providing opening of required size Each 2 978.7 1957.4

& shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar

20 location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of

cut edges etc. complete.

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic Sqm 282 1267.95 357561.9

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

21 Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @

3.3kg per sqm, including pointing in white

cement mixed with pigment of matching

shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing and fixing panelling or panelling

and glazing in panelled or panelled and

glazed shutters for doors, windows and

clerestory windows (Area of opening for

panel inserts excluding portion inside

grooves or rebates to be measured).

Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

TINSUKIA DIVISION-ENGINEERING/N F RLY

9.7.7 Float glass panes

9.7.7.1 4 mm thick glass pane (weight not less than Sqm 135 2241.8 302643

9.7.7.2 5.0 mm thick glass panes (weight not less Sqm 15 2600.45 39006.75

than 12.50 kg/sqm).

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard

wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face

veneers on both faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Sqm 65 3473.85 225800.25

Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board

9.21 construction with frame of 1st class hard

wood and well matched commercial 3 ply

veneering with vertical grains or cross bands

and face veneers on both faces of shutters:

9.21.3 25 mm thick (for cupboard) including ISI Sqm 7.2 2093.7 15074.64

25 marked nickel plated bright finished M.S.

piano hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing chromium plated brass

curtain rod having wall thickness of 1.25mm

9.46 with two chromium plated brass brackets

fixed with C.P. brass screws and PVC sleeves

etc., wherever necessary complete :

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

9.53 Providing 40x5 mm flat iron hold fast 400 Each 120 228.85 27462

mm long including fixing to frame with 10

mm diameter bolts, nuts and wooden plugs

28 and embedding in cement concrete block

300x100x150 mm 1:3:6 mix (1 cement : 3

coarse sand : 6 graded stone aggregate 20

mm nominal size).

9.55S BRIGHT FINISHED M.S. FITTINGS

Providing and fixing ISI marked IS:1341 M.S.

9.55 pressed butt hinges bright finished with

necessary screws etc. complete :

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

tower bolt black finish, (Barrel type) with

necessary screws etc. complete (Copper

oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

handles conforming to IS:4992 with

necessary screws etc. complete (Copper

oxidised as per IS 1378)

TINSUKIA DIVISION-ENGINEERING/N F RLY

9.72S BRASS FITTINGS

9.82 Providing and fixing bright finished brass Each 30 121.65 3649.5

33 hanging type floor door stopper with

necessary screws, etc. complete.

9.84 Providing and fixing aluminium extruded Each 30 983.15 29494.5

section body tubular type universal hydraulic

door closer (having brand logo with ISI, IS :

3564, embossed on the body, door weight

upto 36 kg to 80 kg and door width from 701

mm to 1000 mm), with double speed

adjustment with necessary accessories and

screws etc. complete.

9.88S CHROMIUM PLATED BRASS FITTINGS

Providing and fixing chromium plated brass

9.92 handles with necessary screws etc.

9.105S GYPSUM BOARD PARTITIONS

Providing and fixing factory made uPVC

glazed/wire mesh windows/ doors

comprising of lead free uPVC multi-

chambered frame, sash and mullion/coupler

(where ever required) extruded profiles

having minimum wall thickness of 1.70 mm

for Series R1 and R2 profiles and 2.10 mm

for Series R3 and R4 profiles conforming to

EN: 12608 in any shape, colour and design

duly reinforced with galvanized mild steel

section made of required shape & size as

per CPWD Specification, uPVC extruded

glazing beads, interlocks and Inline sash

adaptor (where ever required) of appropriate

dimension, EPDM gasket, hardware, SS 304

grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching

polyamide PA6 grade sleeve for fixing frame

to finished wall as per IS 1367 : Part 1 to 14,

plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame,

sash & mullion (if required) shall be mitred

cut and fusion welded/mechanically jointed

duly sealed at all corners, including drilling

of holes for fixing hardware and drainage of

water etc. After fixing frame the gap

between frame and adjacent finished wall

shall be filled with weather proof silicon

sealant over backer rod of approved size

and quality, all complete as per approved

drawing conforming to CPWD specification &

direction of Engineer-in-Charge. Section of

steel reinforcement and cross sections of

uPVC profiles to be as per design approved

by Engineer-in-Charge. Wire mesh / Glazing

of plain/ toughened/ laminated/ double glass

unit with / without high performance

coatings as per design requirements and

conforming to IS: 3548 & IS: 16231 shall be

paid separately.

Two track two panels sliding window with

9.147.A1 Aluminium channel for roller track, wool pile,

nylon rollers with SS 304 body.

9.147.A1.1 Using R2 series with frame (40 mm & above) Sqm 36 8298.85 298758.6

x (40 mm & above) & sash (25 mm & above)

36 x (50 mm & above) with zinc alloy (zamak)

powder coated touch locks with hook (Height

upto 1.2 metre).

TINSUKIA DIVISION-ENGINEERING/N F RLY

Three track three panels sliding window with

two glazed & one wire mesh panels with

Aluminium channel for roller track, wool pile,

nylon rollers with SS 304 body.

9.147.A4.1 Using R2 series with frame (70 mm & above) Sqm 36 10993.55 395767.8

x (40 mm & above) & both glazed and fly

screen sash (25 mm & above) x (50 mm &

above) with zinc alloy (zamak) powder

coated touch locks with hook. (Height upto

Fixed window / ventilator with mullion /

9.147.C2.1 Using R1 series with frame (33mm & above ) Sqm 75.6 9155.2 692133.12

x (35mm & above) & mullion (33mm &

above) x (50mm & above). (Height upto 0.90

10.0 STEEL WORK

10.1S General

10.2 Structural steel work riveted, bolted or Kg 12500 133.7 1671250

welded in built up sections, trusses and

39 framed work, including cutting, hoisting,

fixing in position and applying a priming

coat of approved steel primer all complete.

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses

etc., including cutting, hoisting, fixing in

10.16 position and applying a priming coat of

approved steel primer, including welding and

bolted with special shaped washers etc.

10.28 Providing and fixing stainless steel ( Grade Kg 650 772.4 502060

304) railing made of Hollow tubes, channels,

plates etc., including welding, grinding,

buffing, polishing and making curvature

(wherever required) and fitting the same

with necessary stainless steel nuts and bolts

complete, including fixing the railing with

necessary accessories & stainless steel dash

fasteners , stainless steel bolts etc., of

required size, on the top of the floor or the

side of waist slab with suitable arrangement

as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless

steel members shall be considered excluding

fixing accessories such as nuts, bolts,

fasteners etc.).

11.0 FLOORING

11.1S General

Cement concrete flooring 1:2:4 (1 cement :

2 coarse sand : 4 graded stone aggregate)

11.3 finished with a floating coat of neat cement,

including cement slurry, but excluding the

cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone Sqm 450 614.2 276390

cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), including

finishing complete.

11.16S TILE FLOORING

TINSUKIA DIVISION-ENGINEERING/N F RLY

Chequered precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed

with neat cement slurry mixed with pigment

11.20 to match the shade of tiles, including

rubbing and cleaning etc. complete, on 20

mm thick bed of cement mortar 1:4 (1

cement: 4 coarse sand).

44 11.20.4 Ordinary cement without any pigment Sqm 280 1056.35 295778

11.41S VITRIFIED FLOOR TILES

Providing and laying Vitrified tiles in floor in

different sizes (thickness to be specified by

the manufacturer) with water absorption less

than 0.08% and conforming to IS:15622, of

approved brand & manufacturer, in all

colours and shade, laid on 20 mm thick

cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3

kg/sqm including grouting the joints with

white cement and matching pigments etc.

The tiles must be cut with the zero chipping

diamond cutter only . Laying of tiles will be

done with the notch trowel, plier, wedge,

clips of required thickness, leveling system

and rubber mallet for placing the tiles gently

Double charge vitrified tile polished finish of

Glazed Vitrified tiles Matt/Antiskid finish of

Providing and laying Polished Granite stone

flooring in required design and patterns, in

linear as well as curvilinear portions of the

building all complete as per the architectural

drawings with 18 mm thick stone slab over

20 mm (average) thick base of cement

11.56 mortar 1:4 (1 cement : 4 coarse sand) laid

and jointed with cement slurry and pointing

with white cement slurry admixed with

pigment of matching shade including

rubbing , curing and polishing etc. all

complete as specified and as directed by the

Engineer-in-Charge.

11.56.1 Polished Granite stone slab colour of Black, Sqm 140 4481.3 627382

Cherry/Ruby Red or equivalent

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face

unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain

12.42 water pipes conforming to IS : 13592 Type A,

including jointing with seal ring conforming

to IS : 5382, leaving 10 mm gap for thermal

12.42.3 Single tee with door

12.42.5 Bend 87.5 degree

TINSUKIA DIVISION-ENGINEERING/N F RLY

Providing and fixing unplasticised -PVC pipe

clips of approved design to unplasticised -

PVC rain water pipes by means of 50x50x50

mm hard wood plugs, screwed with M.S.

screws of required length, including cutting

brick work and fixing in cement mortar 1:4

(1 cement : 4 coarse sand) and making good

the wall etc. complete.

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed

from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive)

as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37 mm, at 1200 mm

centre to centre, one flange fixed to the

ceiling with dash fastener 12.5 mm dia x 50

mm long with 6 mm dia bolts, other flange

of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts

& bolts of required size and other end of

angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long

12.45 G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm

high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush

finish of tapered and square edges of the

board with recommended jointing compound

, jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm

on both sides of joint and two coats of

primer suitable for board, all as per

manufacturer's specification and also

including the cost of making openings for

light fittings, grills, diffusers, cutouts made

with frame of perimeter channels suitably

fixed, all complete as per drawings,

specification and direction of the Engineer in

Charge but excluding the cost of painting

12.45.1 12.5 mm thick tapered edge gypsum plain Sqm 450 1355.8 610110

53 board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

TINSUKIA DIVISION-ENGINEERING/N F RLY

12.50 Providing and fixing precoated galvanised Sqm 450 738.65 332392.5

iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet

54 should have protective guard film of 25

microns minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins,

rafters and trusses and including cutting to

size and shape wherever required.

Providing and fixing precoated galvanised

steel sheet roofing accessories of total

coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total

coating thickness of 0.05 mm) with Zinc

coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and

polyester top coat 15-18 microns using self

drilling/ self tapping screws complete :

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

CEMENT PLASTER WITH A FLOATING COAT

12 mm cement plaster finished with a

floating coat of neat cement of mix :

13.16S 6 mm CEMENT PLASTER

13.16 6 mm cement plaster of mix :

13.20S PEBBLE DASH PLASTER

13.26 Providing and applying plaster of paris putty Sqm 3000 262.7 788100

of 2 mm thickness over plastered surface to

prepare the surface even and smooth

13.37S INTERIOR FINISHING

Distempering with 1st quality acrylic

distemper (ready mixed) having VOC

content less than 50 gram/litre, of approved

manufacturer and of required shade and

colour all complete to achieve even shade

13.41.1 New work (two or more coats) over and Sqm 1000 185.65 185650

including water thinnable priming coat with

cement primer having VOC content less than

13.44S EXTERIOR FINISHING

Finishing walls with Acrylic Smooth exterior

paint of required shade :

TINSUKIA DIVISION-ENGINEERING/N F RLY

13.46.1 New work (Two or more coat applied @ 1.67 Sqm 1500 160.6 240900

ltr/10 sqm over and including priming coat

of exterior primer applied @ 0.90 litre/10

Painting with synthetic enamel paint of

13.62 approved brand and manufacture of

required colour to give an even shade :

13.62.1 Two or more coats on new work over an Sqm 500 226.25 113125

64 under coat of suitable shade with ordinary

paint of approved brand and manufacture

Lettering with black Japan paint of approved letter

brand and manufacture per cm

16.0 ROAD WORK

16.1S ROADS

Dry brick pitching half brick thick in drains

16.12 including supply of bricks and preparing the

surface complete :

modular) bricks of class designation 7.5

17.0 SANITARY INSTALLATIONS

17.1S General

Providing and fixing water closet squatting

pan (Indian type W.C. pan ) with 100 mm

sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush

17.1 pipe, with manually controlled device

(handle lever) conforming to IS : 7231,with

all fittings and fixtures complete, including

cutting and making good the walls and floors

wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan Each 15 6767.4 101511

67 of size 580x440 mm with integral type foot

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush

17.2 pipe, with manually controlled device

(handle lever), conforming to IS : 7231, with

all fittings and fixtures complete, including

cutting and making good the walls and floors

wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic Each 15 6515.55 97733.25

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.7.2 White Vitreous China Wash basin size Each 30 2226.35 66790.5

69 630x450 mm with a single 15 mm C.P. brass

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.2 Kitchen sink without drain board

17.22 Providing and fixing G.I. inlet connection for Each 35 142.85 4999.75

flush pipe connecting with W.C. pan.

TINSUKIA DIVISION-ENGINEERING/N F RLY

17.22B Providing and fixing CP Brass Single lever Each 30 6940.75 208222.5

telephonic wall mixer of quality and make as

approved by Engineer in charge.(a) 15 mm

Providing and fixing P.V.C. waste pipe for

17.28 sink or wash basin including P.V.C. waste

fittings complete.

17.28.1 Semi rigid pipe

Providing and fixing mirror of superior glass

(of approved quality) and of required shape

17.32 and size with plastic moulded frame of

approved make and shade with 6 mm thick

hard board backing :

17.34 Providing and fixing toilet paper holder :

17.71 Providing and fixing PTMT liquid soap Each 30 168.35 5050.5

container 109 mm wide, 125 mm high and

112 mm distance from wall of standard

shape with bracket of the same materials

with snap fittings of approved quality and

colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail

complete with brackets fixed to wooden

17.73 cleats with CP brass screws with concealed

fittings arrangement of approved quality and

17.73.2 600 mm long towel rail with total length of Each 30 708.95 21268.5

77 645 mm, width 78 mm and effective height

of 88 mm, weighing not less than 190 gms.

17.74 Providing and fixing PTMT shelf 440 mm Each 30 713.2 21396

long, 124 mm width and 36 mm height of

approved quality and colour, weighing not

less than 300 gms.

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, and all

CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement

and testing of joints complete as per

direction of Engineer in Charge. ( Internal

work - Exposed on wall )

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

in Charge. Concealed work, including cutting

chases and making good the walls etc.

18.15S BRASS FITTINGS

TINSUKIA DIVISION-ENGINEERING/N F RLY

Providing and fixing brass bib cock of

approved quality :

Providing and fixing gun metal gate valve

18.17 with C.I. wheel of approved quality (screwed

Providing and fixing ball valve (brass) of

18.18 approved quality, High or low pressure, with

plastic floats complete :

Providing and fixing uplasticised PVC

connection pipe with brass unions :

18.21.2 45 cm length

Providing and fixing C.P. brass shower rose

with 15 or 20 mm inlet

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all floor Per 10000 11 110000

levels) polyethylene water storage tank, IS : Litre

12701 marked, with cover and suitable

89 locking arrangement and making necessary

holes for inlet, outlet and overflow pipes but

without fittings and the base support for

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass stop cock

18.52 (concealed) of standard design and of

approved make conforming to IS:8931.

Providing and fixing C.P. brass angle valve

18.53 for basin mixer and geyser points of

approved quality conforming to IS:8931

19.0 DRAINAGE

19.1S STONE WARE PIPES AND FITTINGS

Constructing brick masonry manhole in

cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix

(1 cement : 1.5 coarse sand (zone-III) : 3

graded stone aggregate 20 mm nominal

size),foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone-III) : 8 graded

stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement

mortar 1:3 (1 cement : 3 coarse sand)

finished with floating coat of neat cement

and making channels in cement

concrete1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate 20 mm nominal

size) finished with a floating coat of neat

cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep

including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total

weight of cover and frame to be not less

than 38 kg (weight of cover 23 kg and

weight of frame 15 kg) :

modular) bricks of class designation 7.5

TINSUKIA DIVISION-ENGINEERING/N F RLY

Making soak pit 2.5 m diameter 3.0 metre

deep with 45 x 45 cm dry brick honey comb

19.32 shaft with bricks and S.W. drain pipe 100

mm diameter, 1.8 m long complete as per

standard design.

19.32.1 With common burnt clay F.P.S. (non Each 2 26861.9 53723.8

modular) bricks of class designation 7.5

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing double action hydraulic

floor spring of approved brand and

manufacture conforming to IS : 6315, having

brand logo embossed on the body / plate

with double spring mechanism and door

weight upto 125 kg, for doors, including cost

21.4 of cutting floors, embedding in floors as

required and making good the same

matching to the existing floor finishing and

cover plates with brass pivot and single

piece M.S. sheet outer box with slide plate

etc. complete as per the direction of

Engineer-in-charge.

21.4.1 With stainless steel cover plate minimum Each 4 2823.85 11295.4

1.25 mm thickness

22.0 WATER PROOFING

22.1S General

22.5 Providing and laying water proofing Sqm 156 617.05 96259.8

treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry

mixed with water proofing cement

compound consisting of applying :(a) First

layer of slurry of cement @ 0.488 kg/sqm

mixed with water proofing cement

compound @ 0.253 kg/ sqm. This layer will

be allowed to air cure for 4 hours.(b) Second

layer of slurry of cement @ 0.242 kg/sqm

mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will

be allowed to air cure for 4 hours followed

with water curing for 48 hours. The rate

includes preparation of surface, treatment

and sealing of all joints, corners, junctions of

pipes and masonry with polymer mixed

26.0 NEW TECHNOLOGIES AND MATERIALS

26.73S PREFAB/PRECAST TECHNOLOGY

TINSUKIA DIVISION-ENGINEERING/N F RLY

Providing and fixing factory made single

extruded WPC (Wood Polymer Composite)

solid door/window/Ceosetory windows &

other Frames/Chowkhat comprising of virgin

PVC polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers

(wood powder/ rice husk/ wheat husk) and

non toxic additives (maximum toxicity index

of 12 for 100 gms) fabricated with miter

joints after applying PVC solvent cement and

screwed with full body threaded star headed

SS screws having minimum frame density of

750 kg/cum, screw withdrawal strength of

2200 N (Face) & 1100 N (Edge), minimum

compressive strength of 58 N/mm2, modulus

of elasticity 900 N/mm2 and resistance to

spread of flame of Class A category with

property of being termite/borer proof,

water/moisture proof and fire retardant and

fixed in position with M.S hold fast/lugs/SS

dash fasteners of required dia and length

complete as per direction of Engineer-In-

Charge. (M.S hold fast/lugs or SS dash

fasteners shall be paid for separately).

Providing and fixing factory made single

extruded WPC (Wood Polymer Composite)

solid plain flush door shutter of required size

comprising of virgin polymer of K value 58-

60 (Suspension Grade), calcium carbonate

a n d natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives

(maximum toxicity index of 12 for 100 gms)

having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face)

& 900 N (Edge), minimum compressive

strength 50 N/mm2, modulus of elasticity

850 N/mm2 and resistance to spread of

flame of Class A category with property of

being termite/borer proof, water/moisture

proof and fire retardant and fixing with

stainless steel butt hinges of required size

with necessary full body threaded star

headed counter sunk S.S screws, all as per

direction of Engineer-In- Charge.