Balance work for the Building of Women Police Station Building Ground Floornear Ghari More in the district of Paschim Bardhaman.

Earthwork in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone ) including removing spreading or stacking the spoils within a lead of 75 metre as per direction.The items includes necessary trimming the sides of trenches, levelling , dressing & ramming the bottom , bailing out water as required complete.

Depth of excavation not exceeding 1500 mm

Earth work in filling in foundation trenches or plinth with goode earth , in layers not exceeding 150 mm. Including watering and ramming etc. layer by layer, complete.

With earth obtained from excavation of foundation.

Flling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating same by through saturation with water and ramming complete including cost of sand.

By Fine sand .

Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand .

Supplying and laying Polythene sheet (150 gm / sqm ) over damp proof course or below flooring or in foundation trenches .

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes

Brick work with 1st class bricks in cement mortar (1:6)

In foundation and plinth

In superstructure

Ground floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor

Ground floor

25 mm thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and painting the top surface with a coat of bitumen (VG- 40) using1.7 Kg/ sqm including heating the bitumen and cost & carriage of all materials complete. (bitumen to be supplied by the agency)

Controlled cement concrete with well graded stone chips ((20 mm graded nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS 456 & relevant special publication, submission of job mix formula after preliminirory mix design after testing of concrete cube as per direction of EIC. Consumption of cement will not be less than 300 Kg of cement with with super plasticiser per cum of controlled concrete but actual consumption will be determined on the basis of preliminary test & job mix formula .

In Ground Floor & foundation with Concrete mixture [ M 20 Grade]

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with rewuired bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting , fixing and stricking out after completion of works.

25 mm to 30 mm wooden shuttering / Upto Ground floor roof level

25 mm to 30 mm shuttering without staging in foundation etc.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, strips binders etc. including supplying of roads, initial straightening and removal of loose rust (if necessary) cutting to requisite length hooking and bending etc. complete as per drawing and direction.

For M.S. / Tor steel.

Upto Ground floor roof level.

Supplying, fitting and fixing fan hook for ceiling with 1.0 m long ,16 mm dia. Rod complete including mending damages.

Plaster (to wall, floor, etc.) with sand and cement mortar including rounding off or chamfering corners, as directed and racking out joints roughening of concrete surface including chipping and application of cement slurry where necessary etc. complete.

With 6:1 cement mortar.

15 mm thick plaster in Ground Floor

With 6:1 cement mortar.

20 mm thick plaster in Ground Floor

With 4:1 cement mortar.

10 mm thick plaster in ground floor.

Neat cement punning about 1.5 mm thick in wall , dado, window sills, floor, drain etc.

Artificial stone in floor , dado, staircase etc.with cement concrete (4:2:1) laid in panels as directed, with topping made with ordinary or white cement (as necessary) and marble dust in proportion (2:1) including smooth finishing and rounding off corners including application of cement sullry before flooring works, using cement @ 1.75 kg/sqm all complete including all materials and labour.(In G Floor/ With graded stone chips :3 mm thick topping (High polishing grinding on this item is not permitted) with ordinary cement.

35 mm thick artificial stone in G.F. roof

Supplying fitting and fixing windows and ventilators with or without integrated grills conforming to I.S. 1038 -1975 and manufactured from rolled steel sections conforming to I.S. to 7452 - 1974 with non friction projection, straightnening if required, fixing lugs in cement concrete (4:2:1) with stone chips 19 mm down , cutting holes and mending good damages to match wuth existing surface complete in all respect excluding glazing.

Opeanable steel windows as per I.S. sizes with side hung shutters and horizontal glazing bars , with or without fixed type ventilators

Ground floor

Two point nose steel hande including fitting and fixing.

Steel peg stay 300 mm long including fitting and fixing.

M.S inegrated griil as per approved design integrated with steel window or ventilator, joints continuosly welded with M.S. flats and bars.

Supplying best Indian sheet glass pans set in putty and fitted and fixed with nails and putty complete in all floors.

4.0 mm thick.

M.S. Gate of jail type as per approved design made of strong M.S. framework and intermidiate sitiffiners/ round / squire bars or angles and with lining of 14 gauge thick M.S. sheets including necessary locking & hanging arrangement fitted and fixed complete with door frame made of ISA 65 x 65 x 8 mm section

Supplying fitting and fixing door frame with M.S. angle as per drawing and direction of required section. The holes for counter sunk machine screw and nut will be such as to fit 8 to 10 mm iron screw. The counter sunk nut to be welded . The nuts are to be welded after carefull checking with screw. All welding spot should be properly filled or rounded smoot including cost of welding hinges for hinge cleates , lugs for hasp bolt , socket bolt etc. and necessary M.S. clampof 25 mm x 6 mm flat 225 mm long as per direction welded to the frame fitted and fixed in position excluding cost of concrete.

M .S. angle frame: 50x50x5 mm @3.8Kg/m

M.S. or W.I. ornamental grill of approved design joints continously welded with M.S. / W.I. flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs above 16 Kg / sqm

Priming one coat on steel or other metal surface with synthetic enamel/ oil bound primer of approved quality including smoothening surfaces by sand papering etc

On steel surface

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary

On Steel surface / hi- gloss/ Two coats (with any shade except white).

Supplying fitting and fixing UPVC pipes A type and fitting conforming to Is: 13592-1992 with all necessary clamps nails, including making holes in walls, floors etc. cutting trenches in any soil thorugh masonry concrete structure etc. .f necessary and mending good damages including jointing with jointing materials(Spun yarn,valamoid / bitumen / M.seal etc.) complete.

110 mm diameter.

Supplying ,fitting and fixing UPVC fittings conforming to IS 13592-1992.

Plain tee110 mm

Shoe 110 mm dia

Rendering the surface of walls and ceiling with white cement based water proof wall putty of approved make and brand(1.5mm thick)

Acrylic distemper to interior wall , celling with a coat of solvent based interior grade acrylic primer as per manufactures specification including cleaning and smoothing of surface.

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of the EIC.

One Coat / Ground floor

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as equired. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.

Normal Acrylic Emulsion.Two Coat in Ground Floor

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm verticle channels 100mm apart in fully stretched position 20mm x 5mm M.S. flat as collapsible bracing properly rivetted and washered including 38mm steel roller including locking arrangement, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in wall, floors etc. and making good damages complete.

Supply of UPVC fittings conforming to IS-13592-1992

Door Tee

110 mm diameter.

Rubber ring

110 mm diameter.

pipe clip

110 mm diameter.

Rubber lubricant 500 ml

Solvent cement 250 ml

Supplying Solid flush type door of Deluxe Decorative (both side ) quality,conforming to IS 2202 the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings.

35 mm thick Leaf Shutter (Single Door)

Supply "Godrej" mortice lock chromium plated with latch and key 4 levers including fitting and fixing complete.

Anodised aluminium barrel /tower/ socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:

150 mm long x 10mm dia. bolt.

Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete.

250 mm x 16 mm dia. bolt.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:

150 mm grip x 10 mm dia rod.

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm and lap and one corrugation minimum side lap. (Payment to be made on area of finished work).

In Roof with 0.50 mm thick sheet

Sub Total

Add GST @ 18% on Sub-Total Cost, i.e.

Add Labour Welfare Cess @ 1% on Total cost after GST, i.e.