Loading
Loading…
New
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹1.5 Cr
EMD Value
₹2.2 L
Closing Date
3 Dec 2026, 6:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
CWE Wellington
Headquarters Commander Works Engineers Wellington, Barracks Post The Nilgiris PIN 643 231
SPECIAL REPAIRS AND REFURBISHMENT TO DD HALL CARIAPPA AND PEREIRA AT DSC WELLINGTON UNDER GE DSSC WELLINGTON
2026_MES_797451_1
85058/E8
Open Tender
Civil Works
Item Rate
180 days
Wellington
Please refer Tender documents.
7 documents required · 7 mandatory
₹1,000
GE DSSC WELLINGTON
₹2.2 L
Yes
5 Nov 2026
5 Nov 2026
5 Dec 2026
5 Nov 2026
3 Dec 2026
26 Nov 2026
6 Nov 2026 - 13 Nov 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. | |||||
| 2Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. | |||||
| 3S & F factory made UPVC ventilator, fixed type of approved colour with glazing all as per manufactuer's instructions and with following sections: (i) UPVC ventilator frame shall be made of UPVC materials confirming to IS-10151. The ventilator frame shall be made of extruded UPVC section having overall dimension 60mmx60mm and having wall thickness 2mm (+/- 0.10mm). (ii) The corners of wall frame shall be jointed by MS galvanised brackets joints mitred and plastic welded. (iii) The hinge side vertical outer frame shall be reinforced with galvanised MS tube of wall thickness 1mm (+/-0.10mm) and tie rod shall be provided at the bottom of the frame (iv) Provn for exhaust fan shall be catered in the frame. (v) Glazing shall be provided with 5mm thick frosted glass fixed with appropriate size of beading as per the manufacture's instructions. (Note: (i) The entire fixing shall be done as per the manufactuer's instructions and specifications and as directed by the Engr-inCharge). (ii) The unit rate quoted shall be included the cost of glas/wire netting and all other cennected acessories.) | |||||
| 4Providing and fixing factory made uPVC door with shuitter; The construction profile shall be over all frame sectional size 60mmx58mm with wall thickness 2.7 (+/-) 0.2mm of extruded section; the corners shall be plastic welded; The hinge side vertical outer frame shall be reinforced with galvanised steel profile of wall thickness 1.2mm (+/-) 0.2mm; The door shall be fixed to walls using 8mm dia, 80mm long MS scrrews minimum 03 Nos on each side; The glazing shall be provided with 5mm thick sheet glass fixed to door frame with UPVC standard beading of sectional size 24.05x16mm & 2mm thick; The bottom portion of door shutter shall be provided with UPVC board of 5mm thick and 1.0m in height fixed with EPDM rubber gasket and the balance portion shall be provided with glazing excluding the shutter fram area; The shutter shall be fixed to frame with using 03 Nos of 3D hinge of suitable size, one multi point mortice lock with powder coated handle of suitable size alongwith atleast two numbers of keys and two numbers powder coated MS tower bolts of suitable size (Note: The door shall be provided complete all as per the manufacturer's instruction and as specifed and directed. The unit quoted rate shall deemed to be included the cost of sheet glass and PVC board and all other accessories) | |||||
| 5S & F UPVC partition consisting of 7mm thick coloured solid UPVC ply sheet reinforced with frame work made of 60mmx60mm casement frame including necessary drilling, jointing and fill the gap with necessary solvent and fixing with all required cleats, brackets, channels etc complete all as specified and directed by the Engr-in-Charge. (Note: The partition shall be disgned acording to the approval of GE and cost shall deemed to be included the cost of glass/PVC panelling as per the design) | |||||
| 6Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality including glazing shall be provided with 5 mm thick plain/ frosted glass with appropriate size of beading as per the manfufacturer's specifications and stainless steel wire mesh 0.36mm nominal dia and average width of aperture 1.4mm shall be provided with each window shutter complete all as specified and directed by Engineer-in-Charge. | |||||
| 7S & F vanetian roller blinds, Classic Screen Zebra, Classic, Manual Operated with following Hardware Specifications: Control Unit: The control unit shall be made of High Strength reinforced plastic. The clutch shall be of wrap spring design. High carbon steel springs shall be provided to transmit motion from driven members of clutch mechanism. Clutch shall be operated directionally by use of endless beaded chain. The clutch should never needs any adjustment. Idler: Idler shall be high strength reinforced plastic, consisting of a centre shaft. The Idler shall be mounted on the bracket by using a plastic lock. The metal sleeve inside the plastic lock should provide bearing surface for the contre shaft, which should be rotated freely, providing smooth, quit and long wearing operation. Head Rail: Head Rail shall be of an aluminium extruded rail, powder coated in white. Control unit and idler shall be mounted on the Head rail with powder coated MS brackets. Roller Tube: The Roller tube shall be of an anodized extruded tube of high strength alloy. Control unit and Idler shall be fixed to the either ends of the tube. The fabric of the blind shall be fitted to the tube with heavy duty adhesive tape. Bottom Rail: The bottom Rail shall be of an aluminium extruded rail with a groove for fixing the fabric and powder coated in white. It shall be fixed to the bottom of the fabric and the purpose of it shall be to keep the fabric in tension and straight. The fabric shall be fitted to the tube using plastic insert. The end caps of the tube shall be of ABS. | |||||
| 7.1 | Operating Chain: The operating chain shall be made of 4.5mm plastic beads moulded on 2.2mm thick polyester chord. The pitch of the beads shall be 6mm. The chain drives the sprockets of the control unit to close and open the blind. The pitch of the chain corresponds to the sprockets shall be perfect match for trouble free operation.
Fixing brackets & Clamps: These shall be used to fix the blind to the wall or ceiling. 'L' bracket shall be made of mild steel and zinc plated. The clamp shall be made up of spring steel of thickness 0.7mm and zinc plated.
Roller Tube: The roller tube shall be of aluminium alloy extruded grooved tube, which shall be anodized of size-32mm O.D, weight - 0.27 Kg/Mtr, Size- 38m O.D, weight 0.38 Kg/Mtr, size- 50mm O.D, weight - 0.60 Kg/Mtr, Alloy & temp - 6063-T6. Fabric shall be fitted to the tube with double sided tape.
Bottom Rail: It shall be extruded aluminium grooved section - powder coated in white size: 21mm O.D. Alloy-HE9WP weight - 0.28 Kg/Mtr. Fabric shall be fitted to the bottom rail with plastic insert. Bottom rail end caps shall be made of ABS.
Fabric Construction: 75% PVC, 25% Polyester, Openness factor 3%, Fabric thickness 0.6 to 0.70 mm, Fabric weight +5% 470 GSM, Fabric width 250 Cms, Fire Resistance NFPA 701, BS 5867 Part-2, Type-A, Colour Fastness to light 6 Grade. Sligh colour aberration may exist and it shall have no reason for claims. Technicall properties are based on average data and may exist deviation technical properties are used for reference and shall not be contractual, Origin India complete all as specified and directed. (Note: The unit quoted rate shall deemed to includes the cost of taking down and removing of existing curtain rods) | - | - | - | - |
| 8Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as directed by the Engr-in-Charge. | |||||
| 9Demolition of un-reinforced cement Concrete of any description and in any position not otherwise specifically provided for including removal of debris upto outside the MD land as directed complete all as specified and directed. | |||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.30 MB
tmrgd_85058.pdf
Tender Documents • 1.45 MB
BOQ_894521.xls
BOQ • 0.40 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .