SPL REPAIR TO BLDG NO T-811 (SINGLE JCOS LIVING ACCN) ,PROVN OF 01X TOILET BLOCK, SOAKAGE WELL AND PROVN OF STORM WATER DRAINS UNDER GE (ARMY) SURATGARH AT SURATGARH MIL STN

Amount

Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling of stone slabs in roofs, suspended floors, chajjas, landings, etc., any description, any thickness, jointed in any mortar, complete all as specified & as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down old rusted & damaged steel windows of any description and of any type & size with guard bars / grill including cutting holes for hold fasts & making good the disturbed portion complete all as specified & as directed.

Taking down old rusted & damaged steel ventilators of any description and of any type & size without guard bars / grill including cutting holes for hold fasts & making good the disturbed portion complete all as specified & as directed.

Dismantling of cast iron or PVC , jointed incement mortar pipes up to 100 mm bore in any position complete all as specified and as directed

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete including loosning of bolts , cutting rivets and taking down carefully all as directed by Engineer-In-Charge.

Demolition of existing false ceiling complete incuding fillets, grid complete all as specified and as directed

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges complete all as specified and as directed

Dismantling carefully and taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Dismantling carefully and taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with old size fly Ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed.

All as per serial item No 15.00 here-in-before but except bricks. Note : Old serviceable burnt clay / fly ash bricks retrieved from serial item No. 3.00 here-in-before shall be used under this item.

M&L for brick work with old size Fly Ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for steel work as in tubular trusses, purlins, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 including painted with one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed by Engineer-in-charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails , fixed with angle cleats or other connecting plates, gusset plates, etc conforming to Fe-290 (Gde E- 165), complete all as specified & directed by Engineer-in-charge.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc conforming to Fe-290 (Gde E- 165, complete all as specified & directed by Engineer-in-charge.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge. Note:- (i) Roof sheet shall be required and fixed in arch/curve/angular shape as per user requirement/as per directed by Engr-in-charge and nothing shall be paid extra on this account. (ii) Company provided warranty certificate to be submitted with payment. Make : JSW colouron+/ Tata blue scope/ Jindal neo colour or other technocommercial as mentioned in apx 'A' herein after.

S&F for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-charge. Note:- (i) Roof sheet shall be required and fixed in arch/curve/angular shape as per user requirement/as per directed by Engr-in-charge and nothing shall be paid extra on this account. (ii) Company provided warranty certificate to be submitted with payment. Make : JSW colouron+/ Tata blue scope/ Jindal neo colour or other technocommercial as mentioned in apx 'A' herein after.

S&F Composite cement designer ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel designer ceiling pre finished conforming to IS 14862 type B cateogory three incl powder coated GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster complete all as specified and as directed by Engineer in charge MAKE: ARMSTRONG/EVEREST/SAINTGOBAIN or other Technocommercial as mentioned in Appx 'A' here in after

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete Complete all as specified and as directed.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed

M& L for rendering 10 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6,even and smooth w/o using extra cement Complete all as specified and as directed.

M&L for 15 mm thick rendering in two coat (10+5 mm) on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4 Complete all as specified and as directed. (Note: Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location)

M& L for rendering 5 mm thick on fair faces of brick or concrete surfaces in ceiling in cement mortar 1:3,even and smooth w/o using extra cement Complete all as specified and as directed.

M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in sun-shades, chajjas, shelves, cills landings, cover stone including cutting chasing as directed

M&L Granite 18-20 mm (South type/Galaxy) thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite over 15 mm thick screed bed of CM 1:6 complete all as specified and as directed by Engineer-in-Charge. Note : Edge to be finished with mirror polishing including nosing.

M&L for Machine cut kota stone slab 18 - 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl.rubbing and mirror polishing laid over 15 mm thick cement screed base in CM 1:6. The joints shall be 20mm wide filled with cast in situ tarrazo with white marble chips of size up to 6mm complete all as specified and as directed

All as per item No 32 above but in skirtings laid over 10mm thick backing layer in CM 1:4

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 10 mm thick Vitrified colored Double charged /stainless tiles of size n.exc. 0.36 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces complete all as specified and as directed Note :- colour and shade shall be approved by GE

ditto as per Serial item above 36 but with 10 mm thick in CM 1:4 as on vertical surface.

Glazed ceremic tiles white 600X300mmX7mm thick coloured,set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4 complete all as specified and as directed.

Supply & Laying 20mm outer dia dia CPVC pipes SDR 11 & Plain/Brass fittings(Elbow,Tee,MTA,FTA,Union) CPVC SDR 11 fittings laid in trench or fixed in walls or laid in floors complete all as specified and as directed by Engineer-In-Charge

Supply & Laying 25mm outer dia dia CPVC pipes SDR 11 & Plain/Brass fittings(Elbow,Tee,MTA,FTA,Union) CPVC SDR 11 fittings laid in trench or fixed in walls or laid in floors complete all as specified and as directed by Engineer-In-Charge

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded tanks four layer (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. MAKE: Sintex Pure /Ashirvad Weatherguard / Asteral cleo or other Technocommercial as mentioned in Appx 'A' here in after.

Supply and fixing 1000 Litre capacity Rotational moulded tanks four layer (cylindrical vertical with closed top) , hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. MAKE: Sintex Pure /Ashirvad Weatherguard / Asteral cleo or other Technocommercial as mentioned in Appx 'A' here in after.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125x65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).including dismantling existing wooden/Iron /stone chowkhats complete and making good existing disturbed surface with CM 1:3 complete all as per specified and directed by Engineer-In-Charge.

S& F for 35 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L for Powder coated window frames ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as specified and as directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators. including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall not be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285,Aluminium handles, tower bolts , fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. complete all as specified and as directed.

M&L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I section 8, clause 8.20 (a) supplied and fixed to chowkats complete all as specified and as directed

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S& F for 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

S&F 3 mm Sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 4 mm Figured glass ,pin head type and glazing with spring clips in metal surroundsand oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L Galvanised Mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples complete all as specifed and as directed

Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed

S&F steel locking bolts with mild steel electro galvanised plate and bright bolt not less than 10 mm dia and 100 mm size, complete all as specified .

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F for 150mm size aluminium anodised handle of febricated type and fixed complete all as specified and directed.

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 200 mm complete all as specified and as directed

S&F mild steel finished floor door stopper of 140 mm complete all as specified and as directed

S&F 250 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed

S&F mild steel pressed handles oval type stove enamelled black of 150mm

S&F as in repair 25 mm thick Stainless Steel pipe Curtain Rod fixed with 2 nos steel brackets and Steel knobs at both ends as per site requirement including making good disturbed portion with 1:3 cement plaster and finshing treatment of existing wall quality complete all as specified and as directed by Engineer-In-Charge.

S&F ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm complete all as specified and directed

S&F as in repair Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe complete all as specified and directed MAKE HINDWARE QUED/JAQUAR/PARRYWARE or Techno commercial as mentioned in Appx 'A'.

S&F Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated hinging device, complete all as specified and directed

S&F as in repair wash hand basin vitreous china size 550x400mm white flat back waste,chain plug,600mm pvc connection, 32mm bore pvc waste pipe comp all as specified fixed complete all as specified and as directed

S&F as in repair PVC low level flushing cistern 10 litres capacity, ISI MARKED white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and as directed

S&F as in repair bib taps long body cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed having minimum weight as per IS 8931 complete all as specifed and as directed Make : Jaquar/Hindware/Johnson or equivalent technocommercial make as specified in Appendix 'A'.

S&F bib taps long body cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed having minimum weight as per IS 8931 complete all as specifed and as directed. Make : Jaquar/Hindware/Johnson or equivalent technocommercial make as specified in Appendix 'A'.

S&F in repairs pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed having minimum weight as per IS 8931 complete all as specified and as directed

S&F in repair 15 mm bore Brass chromium plated wall mixer L-BEND non telephonic for mixing hot and cold water screwed down for iron pipe complete all as specified and as directed by Engineer-in-Charge. MAKE : HINDWARE QUED/JAQUAR/Johnson or Techno commercial as mentioned in Appx 'A'.

S&F as in repair angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed having minimum weight as per IS 8931 complete all as specified and as directed by Engineer-in-Charge. Make : Jaquar/Hindware/Johnson or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair 150 mm Overhead square ABS Shower Full Chrome with Brass Arm 225 mm & Flange complete all as specified and directed. CAT Part No:- BOS-90S of Parayag or equivalent cat in Hindware andJaquar and johnson or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair towel rail Chromium plated brass complete all as specified and directed . CAT Part No. BA-01 of Parayag Or Equivalent in hindware,somany,jaquar or equivalent technocommercial make as specified in Appendix 'A'.

S & F as in repair glass corner of size 300mmx300mm with 5.5 mm thick glass and steelness steel clip and steelness steel railing allround the shelf complete all as specified and directed by engineer in charge .

S&F as in repair CP soap dish, fancy type fixed to wall with CP brass screws , complete all as specified and as directed by Engineer-in-Charge.

S&F as in repair Spray jet, brass chromium plated, with and including 1.5 metre long PVC flexible reinforced pipe for EWC, for bore dia of pipe 15mm,complete all as specified and as directed by Engineer-in-Charge. Make : Somany/Hindware/Johnson or equivalent technocommercial make as specified in Appendix 'A'.

S&F as in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified .(Min weight 45 to 60 gms .

S&F as in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge"

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) reducers 110mm to 75mm complete all as specified and directed by Engineer-in-Charge

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge

S&F PVC (SWR) gully trap 125/110mm , setting and jointed with solvent cement complete all as specified and directed by Engineer-in-Charge

S&F PVC (SWR) multi floor trap 75mm dia with grating , setting and jointed with solvent cement complete all as specified and directed by Engineer-in-Charge

M & L for preparation of newly plastered surfaces of wall & applying two coats of Interior emulsion paint by Roller or Air Spray over 1 mm thick wall care putty (Multipurpose mixer shall be used for uniform and proper mixing of putty) complete all as specified and as directed by Engineer-in- charge. (Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent technocommercial make as specified in Appendix 'A'.

Material & Labour of preparation newly plastered and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge. (Make :- Apex Ultima (Asian Paint), Weather Coat anti dust ( Berger Paint ), Excel No Dust ( Nerolac) or equivalent technocommercial make as specified in Appendix 'A'.

M&L Complete removal of existing treatment and preparation of old decorated (platered or unplastered) of wall by Vaccume based sanding machine, removal of nails etc including filling of cracks and applying two coats of Interior emulsion paint by Roller or Air Spray incl over a layer of 1 mm or as required ( Multipurpose mixer shall be used for uniform and proper mixing of putty) of wall care putty, on plastered surfaces,prepara-tory to distempering complete all as specified & directed by Engineer -in-charge. (Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or equivalent technocommercial make as specified in Appendix 'A'.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified & as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth for foundation etc. Complete all as specified and as directed By Engineer-In-Charge.

M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and directed by Engineer-in-charge. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

M&L for brick work with sub class B Bricks, old size straight or curved on plan exc 6 mtr mean radius built in CM 1:4 complete all as specified

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, coping, parapets and railing upto 60cm height, copings bed block, roof kerbs or mud stops, kerb stone, kneelers, apex stones, bed plates, surface channels and drains, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for renderidng 15mm thick in cement mortar 1:4 on fair faces of brick /concrete surfaces complete all as specified and directed

Surface excavation avg 15cm deep and not exceeding 30cm deep and getting out in soft/ loose soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in including spreading levelling and well ramming in layers n exc 25cm each complete all as specified and as directed

Removing excavated material not exc. 250 m but not exc. 500 m and depositing where directed at a level not exc. 1.50m above the starting point in soils

M&L for hardcore of broken stone / boulders gauge not exc. 63mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-charge.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc 15cm thick including spreading , levelling , watering and well ramming complete all as specified and as directed.

Excavation over area n exc. 1.5 m deep and getting out in soft soil complete all as specified and as directed.

Excavation over area exc. 1.5 m but n exc 3 m deep and getting out in soft soil complete all as specified and as directed.

Excavation over area exc. 3 m but n exc 4.5 m deep and getting out in soft soil complete all as specified and as directed.

Excavation over area exc. 4.5 m but n exc 6 m deep and getting out in soft soil complete all as specified and as directed.

M&L sub class B honey comb brick work for soak well wall in CM 1:3 complete all as specified and as directed.

M&L jodhpur stone of roof slab self faced 1.5cm to 10 cm thick 25 to 35 cm wide hoisted and set jointed and grouted in cement and sand mortar 1:6 complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate , as in floors over stone patti roof slab finished the surface even and fair comp.all as specified.

S&F factory casted 60mm thick machine pressed cement concrete PU moulded interlocking paving blocks M-35 having compressive strength not less than 350 Kg / Sqcm using grey cement and with pigment and of shape hexagon/ triangular / zigzag / I-shaped / Three-X etc as directed conforming to IS 15658-2006 complete all as specified and directed by Engineer-in-Charge.

M&L for Loose filling of broken brick boulders of guage 40 to 80 mm in soak well in layeres or as in side packing of walls complete all as specified and as directed by Engineer-In Charge.

M&L for tibba sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms, mould, mitred, stopped ends etc all as specified

M&L precasted SFRC manhole/Drain cover with frames square/round size as per ground requirement provided with suitable mild steel rims and easy lifting hooks of medium duty 10 MT as per IS 12592 pt I complete all as specified and as directed

M&L for pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in landing, cover slab(vibromechanically floated) for manholes, septic tanks, soakage wells, chullah hood, chajjas, water troughs, mangers, shelves and similar articles with plain fair faces including chamferred, weatherings, throating etc including necessary form work and setting in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge Note: - Reinforcement shall be measured and paid for separately.

M&L RCC pipe 300 mm bore in class NP-2 laid and jointed complete with collars all as specified & directed

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed of RCC 300 mm bore pipe incl packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L RCC pipe 150 mm bore in class NP-2 laid and jointed complete with collars all as specified & directed

M&L PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in bed of RCC 150 mm bore pipe incl packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

All as per serial item No 124 here-in-before but 5mm dia and over up to and including 10mm dia as in stirrups, spacers & binder etc complete all as specified and directed.

M&L for use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick (horizontal or sloping), rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge.

M&L for use and waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and other similar works complete all as specified and directed and directed by Engineer-in-Charge.

M&L for reinforced cement concrete (1:2:4) type B-1(using 20 mm graded crushed stone aggregate) as in beams , cantilever, bressummer, lintel over 1.5m span and similar work complete all as specified and directed by Engineer-in-Charge

M&L for masnory work with precast Autoclave Aerated Concrete (AAC) Blocks , light weight eco friendly having excellent thermal insulation and acoustic properties with approved adhesive/mix mortar, straight or curved on plan exc 6 m mean radius complete all as specified.

M&L for cutting grooves in brick wall , 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed

S&F as in repair gun metal globe or gate valve 20mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engineer-in-charge.

S&F grating doom 100mm dia of PTMT (minimum weight 25 grams) over floor trap in white/grey cement to match with exisitng floor complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china half stall type, flat back urinal of size 390 x 375 x 590mm, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe, chromium plated urinal spreader including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed by Engineer-in-charge.

M & L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation for stays & mass concrete including necessary form work and fair finishing complete all as specified and directed by Engineer-in-charge

Supply only integral water proofing compound (ISI marked) complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering in cement mortar (1:4) on brick walls/concrete surfaces mixed with water proofing compound 3% by weight of cement finished as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note : - Water proofing compound shall be measured and paid seperately in respective item.

S&F DWCPE (SN8) pipe 160 mm dia (inner) as per IS-16098 (Part-II) laid in trenches or in floor on moorum bed to required shape including all necessary accessories / fitting / jointing / rings, joiting and testing over bed of 100mm thick PCC 1:4:8 type D2 using 40mm graded aggregate complete all as specified & directed by Engineer-in-charge.

M&L for PVC SWR gully trap 125/110 mm setting and jointing withsolvent cement complete all as specified and as directed by Engineer-In-Charge.

M&L for cutting into existing manhole/Septic tank/Soak well for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1, smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and directed by Engineer-in-charge.

Material & labour construction of Soak Well for 10 to 25 users as shown on drawing No.GE(A) /comp / 17 / 2016 complete all as specified and as directed by Engineer-in-charge. Notes : Irrespective to whether shown on drawing or not, excavation & earthwork shall be in any type of soil, brick work shall be in CM 1:4, over burnt brick bats shall be used for filling, PCC 1:4:8 type D2 using 40mm graded stone aggregate shall be provided in foundation, 20mm dia MS rungs made to shape painted with two coats of bituminous paint shall be provided, PCC 1:3:6 type C2 using 40mm graded stone aggregate shall be provided in plinth protection, 1.50m long 150mm bore cast iron sand cast inlet pipe shall be provided and slab shall be Precast RCC (1:2:4). Other details shall be as shown on drawings & as specified in particular specifications.

M&L for construction of Septic Tank for 100 users as shown on drawing No. BTD-016 sheet No. 1/3 to 3/3 complete all as specified and as directed by Engineer-in-charge. Notes : Irrespective to whether shown on drawing or not, excavation & earthwork shall be in any type of soil, RCC in foundation shall be M-25 (Nominal Mix) over lean concrete (1:3:6) using 40mm graded stone aggregate over brick hard core, all PCC shall be M-25 (Nominal Mix) using 20mm graded stone aggregate, all RCC work shall be M-25 (Nominal Mix), brick work shall be in CM 1:4, 20mm dia MS rungs made to shape painted with two coats of bituminous paint shall be provided. Other details shall be as shown on drawings & as specified in particular specifications.

S&F 15mm dia stop valve (concealed type) cast copper alloy, angular type with, chromium plated long shank and cup with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge.

S&F vitreous china wash basin white, flat back of size 550x400mm , counter type, table top over granite slab including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10 x 7.5 x15 cm with & including 32 mm dia PVC waste pipe, 32mm dia PTMT waste coupling half or full thread (minimum wt 45 grms) flange end bedded in red lead cement & other end fixed to waste pipe and including brass chromium plated fancy type pillar tap, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. with & including WC seat cover closed pattern with flat bottom and cover, health faucet ABS CP, one piece /single body pvc alongwith blow moulded concealed cistern, pneumatic type capacity 10 litre including chrome finish dual flush control plate, flushing pipe and fixing bracket complete assembled with necessary fittings and fixtuers including necessary brick work and plastering for fixing the concealed cistern complete all as specified & as directed by Engineer-in-charge.

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 148 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 148 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per Srl item No. 148 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular switch piano 16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Modular socket 6 pin, 6/16 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge. Make :Havells (Crabtree)/Legrand Model Myrius/Honeywell Model ORNA or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F sheet metal plug & socket DB, SP, with a two pin and earth plug with socket, 230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix "A".

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80 Make : Havells Cat No LHLDDEBNL5R10/WIPRO/PHILLIPS/CROMPTON or equivalent Technocommercial cat part of Make as specified in Appendix "A".

S&F Energy saving 9/10 watt environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs, IP 65 protection fixed on wall complete all as specified and as directed by Engineer-in-charge. Make : Crompton Cat No CIS-306-10-57-SL-DP-NBK/WIPRO/HAVELLS or equivalent Technocommercial cat part of Make as specified in Appendix "A".

Supply, fixing and testing as in repair LED Street / Security light fitting of 30 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge.Make :Havells Cat Part No LHETAVU7PA7J030/ Crompton Cat No TRP-415-30-57-SL-LM-NBK/Wipro Cat No D912065 or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair flush mounting factory made VTPN DB 4 way, 415 Volt, Double door, IP-43 protection, IK-09 with metal door with 160 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair MCB 40-63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

S&F as in repair MCB 100 Amps, Four Pole, 415 Volt Volts, 25 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make :Legrand/Havells/L&T or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after

Disconnecting and taking down old Unsv ceiling fan and depositing to AGE EM Yard S&F ceilling fan copper wound complete with blade, down rod, electronic regulator and accessories AC, 230 V, 50 Hz, 1200mm sweep, min air delievery 210 CFM with serving value 6.00 BEE, with Brush less direct current motor (BLDC) complete all as specified and directed by Engineer-in-charge.Make :Havells/Usha/Bajaj or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after Note :- MES No with stencil shall be marked on ceiling fan body using synthetic enamal paint. Cost of the same is included in the unit rate of this item.

Disconnecting and taking down old Unsv exhaust fan and depositing to AGE EM Yard and S&F exhaust fan,AC, 230 V, 50 Hz, steel body 300mm sweep with blades frames and louvers complete all as specified and directed by Engineer-in-charge.Make :Almonard/Havells/Usha/Bajaj or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after Note :- MES No. with stencil shall be marked on Exhaust fan body using synthetic enamal paint. Cost of the same is included in the unit rate of this item.

Disconnecting and taking down old Unsv Electric water heater (Geyser) and depositing to AGE EM Yard and S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2Kw, capacity 25 Litre, BEE 5 star including all accessories complete all as specified and directed by Engineer-in-charge. Make :ORIENT/Havells/CGPISL or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after Note :- MES No with stencil shall be marked on Geyser body using synthetic enamal paint. Cost of the same is included in the unit rate of this item.

S&F exhaust fan,AC, 230 V, 50 Hz, steel body 300mm sweep with blades frames and louvers complete all as specified and directed by Engineer-in-charge. .Make :Almonard/Havells/Usha/Bajaj or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after Note :- MES No with stencil shall be marked on Exhaust fan body using synthetic enamal paint. Cost of the same is included in the unit rate of this item.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2Kw, capacity 25 Litre, BEE 5 star including all accessories complete all as specified and directed by Engineer-in-charge.Make :ORIENT/Havells/CGPISL or equivalent in Techno commercial makes mentioned in Appendix 'A' here-in-after Note :- MES No with stencil shall be marked on Geyser body using synthetic enamal paint. Cost of the same is included in the unit rate of this item.

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

S&F as in repair street light bracket made out of 32mm dia GI pipe light grade 1.20m long , bent to shape at 120 degree angle from vertical fixed along pole with and dirlling holes including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint including any addition / alteration (if required) for fixing street light complete all as specified and as directed by Engineer-in-charge.

S&F HDPE DWC pipe inner dia 50mm and outer dia 63mm for laying in cable laid in trenches complete all as specified and as directed

S&F as in repair Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches / under road / drains, fixed to poles / walls with required numbers of clamps made out of 25x3mm flat iron, bolts, nuts and washers for protection of LT electric cable complete all as specified and as directed by Engineer-in-charge. Notes :- (i) Excavation & earthwork shall be measured & paid for separately under respective items of BOQ (ii) Cost of flat iron clamp if required is included in the unit rate of this item. Nothing extra shall be paid on this account.

S.K BUILDERS AND ENGINEERS (BID ID -3498900)

BANSAL BROTHERS (BID ID -3499146)

PACHAR BROTHERS (BID ID -3499580)