COMPREHENSIVE MAINT AND MISC B/R AND E/M WORKS AT SIG REGT TOI MES IB, SWIMMING POOL, KLP SPORTS COMPLEX MADHUBAN PARK AND SOMNATH ENCLAVE UNDER AGE B/R-II OF GE SUKNA

Amount

M & L for plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in roof kerbs, rounded or chamfered on haunching in chajjas to prevent water seepage into brick walls, including necessory formwork (upto height of 8 mtr) rounded or chamfered on edges complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheets and brick wall, thickness of concrete bed exc. 5 cm and not exc.10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork ht up to 7 m complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, ciunter basins and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L 18 to 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 Sq. cm and not exceeding 13 Sq. Cm complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-1, section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with MDF board exterior grade, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

M&L for 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site as per specification and drawing given on MES schedule standard of rate 2020 including dismantling and complete all as per specified and as directed by Engr-in-charge.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F in repairs 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 125mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs Hasp and staple 100 mm safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repairs 28 mm dia harrison rail, decorative type, mild steel, chromium plated with fixing brackets, stops, rollers etc with two Nos of socket, end caps and brackets (decorative type) complete for window opening complete all as specified and directed.

S & F Floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

S & F Joist, channel, angle, flat iron or tee sections, fixed independently, with connecting plates, etc. confirming to Fe 410 -W (Gde-250 quality A) complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S&F in repairs steel rolling shutters without ball bearing, with thickness of laths 1.00 mm push and pull or mannual type including top cover, anchoring rod, hasp and staple with one shop coat of red oxide or zinc chrome primer and fixed in position in existing opening complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers including locking plate for rolling shutter complete all as directed.

S&F Ball bearing of suitable sizes complete for rollong shutter complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in replacement 4 mm thick E-board (designer pattern) celing of size 60x60 cm, fixed or laid / inserted to with and including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and with and including anodised aluminium snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle for false ceiling Hangers with 6 mm dia. G.I. (length as required) adjusting level fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed including necessary dismantling of existing unserviceable ceiling boards of any thickness incl cover fillets complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in plinth protection/path laid in alternate bays and construction joints to be given at every 3M interval and corners of buildings and filled with bituminous mastic or equivalent filler complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, paving, path etc complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300x 450x 7 mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:4 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:4 complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. Note : Sand bedding shall be measured and paid for seperately.

M&L for prepolished cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and fair complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for painting the new WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- Applying a thin layer of wall care putty to obtain smooth finish (c) Priming surface- Applying one coat of alkali resistant primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the old WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Complete removal of existing old plastered or previously untreated surfaces of wall. (b) Putty application- Applying a thin layer of wall care putty to obtain smooth finish (c) Priming surface- Applying one coat of cement based primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the NEW CEILING surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the old WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preperation of old plastered or previously untreated surfaces of wall. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of oil bound distemper.

M & L for painting the OLD CEILING surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of oil bound distemper.

M & L for painting the old wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously treated surfaces of walls (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of weather coat exterior paint. (Note:- The rate are inclusive of necessary scaffolding)

M & L for painting the new wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of cement base paint.

M & L for painting the old wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of cement base paint.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

S&F 4 mm thick obscured/ frosted / pin headed glass in ventilator shutters not exc 0.50 sqm in each pane complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M & L for painting the new wood surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of pink primer (c) Painting- Applying two coat of synthetic enamel paint.

M & L for painting the old wooden surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the old steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the new steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of red oxide primer (c) Painting- Applying two coats of synthetic enamel paint.

M&L in repairs High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

Demolition of brick work in cement motor including pillar etc below / above ground level etc and removing to a distance not exc 50 meter complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No.94.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 94.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 94.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

Material and labour for point wiring of 15 amps socket on independent board with 2.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor as main line drawn through and including PVC casing caping including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling and earth conitinuity conductor 2.5 sqmm (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of suitable sizes with plastic laminated white/coloured top sheet cover 3 mm thick including making good all disturbed surfaces to match the existing complete all as specified and directed.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

All as per Sl. item No. 99 above but for one 3 / 5 Amps socket outlet point on independent board.

All as per Sl. item No.99.00 above but for one 3 / 5 Amps socket outlet point on the same board.

All as per Sl. item No. 99.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per item No. 99.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 6.00 sqmm main wire along with 1 run of 6.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 4 runs of 10.00 sqmm main wire along with 1 run of 10.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano flush type one way, 15 / 16 Amps, 240 volt complete all as specified and directed.

S & F Switch piano 5 Amps single pole two way complete all as specified and directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type two way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S & F Socket outlet 5 Amps 3 pin flush type complete all as specified and as directed.

S&F switch socket outlet 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F switch socket combination 5 pin 6 Amp, flush type universal complete all as specified and directed.

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S&F in repair stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type, white 120 W - 2 module complete all as specified and directed.

S & F Bell push, flush type, 5 Amps single pole complete all as specified and as directed.

S & F Bell, AC 230 Volts single pole complete all as specified and as directed.

S & F Bell multi music type, AC. 230 volts, single pole completed all as specified and directed.

S&F modular type Bell push 6 A , 1 module complete all as specified and directed.

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole completed all as specified and directed.

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 6 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver including all fixing arrangement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR6WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 9 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR9WLED857S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 15 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR15WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 18 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- edgeprorddlr18WLED840SG2 or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 24 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR24WLED857S or equivalent Make of Philips / Crompton ..

S&F in replacement Recessed Mounted Square (2'x2') LED Panel light 36 watt with CRCA powder coated housing & high transmittance Opal diffuser for glare free with Electronic LED Driver. IP20, PF =0.95, System Lumens =120 lm/W, 5700k CRI = 80, Operating Voltage range 140 V - 270 V.complete all as specified and directed.

S & F in repairs Surface and wall mounted LED batten 10 watt 2ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S & F in repairs Surface and wall mounted LED batten 20 watt 4ft long with Aluminum extruded housing , high quality polycarbonate diffuser & integrated Electronic Driver with IP20, PF 0.90, Efficiency not less than 110 lm/W color temp 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed.

S & F in repairs LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF =0.95, total System Lumens not less than 1100 lm, 6500k CRI = 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed.

S&F in repair VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-54 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 160 complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as direct. Make: Cat ref 507750 of Legrend/L&T or equivalent.

S&F in replacement Double door TPN DBs 4 Way, of powder coated DB's suitable for MCB's fitted with bus bar, neutral link, earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed.

S&F MCCB 4 pole 125 Amps breaking capacity 25 KA, Ics = 100% Icu including spreader link & taking down complete all as specified and directed.

S&F MCB TPN 40 to 63 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB ,SPN DB, 08 ways double door, Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete including. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F in repair Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connenction complete all as specified and as directed.

S&F ventilation fan 200 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F ventilation fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F wall mounted fan 400 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to fan and writing MES number in 2 cm height with synthetic enamel paint and fixing on wall and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

M &L in replacements Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 12W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 15W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 18W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 24W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 36W complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 100mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 175mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 200mm x 150mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 250mm x 200mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 350mm x 300mm x 50mm size complete all as specified and directed.

S & F in repair wall light of single head of with 9 watt LED lamp of base B-22 inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Philips / Havells/ Crompton .

MAURYA CONSTRUCTIONS (BID ID -3490873)

S D CONSTRUCTION CO (BID ID -3491140)

Jagatbandhu Enterprises (BID ID -3490248)

MS ESSCON (BID ID -3490680)

M/S ASHRAFI CONSTRUCTION (BID ID -3490809)

M/S A C PAUL (BID ID -3490004)

SHRI ARUN BHATTACHERJEE (BID ID -3490765)

Janata Enterprises (BID ID -3490653)

D K SARKAR (BID ID -3490037)

DAS AND GHOSH CONSTRUCTION (BID ID -3490236)