ADDN ALTN AND SPL REPAIR TO OTM ACCN AT CORPS HQ AND MD ACCN AT RMS (PH-I OF TWO PHS) AT RANGAPAHAR MIL STN

Amount

Demolition of brick work/stone masonry built in cement mortar or cement lime mortar including all quoins, arches etc complete. (4.2 + 81.8)*

Demolition of RCC of any description and in any position not otherwise specifically provided. (0.74 + 5.8)*

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level. (94 +106.45)*

Dismantling of plain or corrugated steel sheeting of any guage/thickness in roof covering/wall clading. (1368 + 9003.50)*

Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames). (41 + 979)*

Taking down Chowkhat or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters from the frames). (52+348)*

Dismantling timber scantlings 40 sqcm and over in section, in unframed work any position. (7 + 0)*

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. (1334 + 8157)*

Dismantling wall and ceiling board fibre, insulation etc or insulation boards any thickness including cover fillets. (1173+3248)*

Taken up or down 15 mm dia steel tubing and connections and removing from site complete all as specified and directed. (973+2200)*

Taken up or down 20 mm dia steel tubing and connections and removing from site complete all as specified and directed. (164+660)*

Taking down cement plaster on brick or stone wall including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. (407+8920)*

Dismantling boarding of any description and fixed in any position fixed with nails or screws. (51 + 332)*

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing. (292 + 0)*

Dismantling wrought iron or MS work of any description not otherwise described. (0.04 + 25)*

Excavating in Trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth, for foundation etc or for shafts, wells, cesspits, manholes etc not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed. (375 + 433)*

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in trenches complete all as specified and as directed. (174 + 187.3)*

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified ans as directed. (201 + 246)*

M &L for PCC 1:4:8 (40mm graded aggregate) type D2 as in foundation complete all as specified and directed. (1.75 + 98.00)*

M & L for PCC (1:3:6) type C-2 using 40mm graded aggregate as in bed blocks complete all as specified and directed. (4 + 4)*

M & L for brick work with sub class 'B' brick full brick thick straight or curved on plan n. exc 6m mean radius built in CM 1:6 complete all as specified and directed (39 +140.00)*

Use and waste of Form work to sides and soffits of floor or roof beam, beam haunchings, girders bressummers, lintels, contilevers, shelves including supports overhangs etc also splays between floor and beams etc. complete (6 +0)*

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for colums, hooking ends, and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips (112 + 242)*

All as per Sr. Item No.1.023 here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders (20 + 60)*

M & L for Reinforced cement concrete (Nominal mix) Type B1, 1:2:4 using 20mm graded stone aggregate as in lintel beams over 1.5m span etc (0.64 + 0.64)*

M & L for RCC type B1 1:2:4 (20 mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (0.74 + 0.74)*

M & L for Hardcore of broken stone or boulders of gauge n exc, 63 mm deposited spread and levelled in layers n exc. 15 cm thick watered and rammed to a true surface (26.35 + 100.15)*

S & F mild steel conforming to Fe-290 Gde-E-165 as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles (47 + 247)*

S&F mild steel conforming to Fe-410- W (Gde-E-250) quality A Post, joist, channel, angle or tee section fixed independently without connection plates. (2047 + 2047)*

S&F MS plate (Plain or chequred) channels, (ordinary and counter sunk) forming holes, with out any attachment confirming to Fe-410-W (Gde E - 250) Quality - B (83 + 584)*

M&L for rolled mild steel conforming to Fe 410-W (Gde-E 250) quality-A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc (3690+6190)*

M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint in any tint complete all as specified. (51 + 271)*

M&L for preparation of new or previously untreated surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide prime in any tint complete all as specified. (197 + 348)*

M&L for preparation of old painted surfaces of Brick, Stone, Concrete, Asbestos Cement work of any description over 10 cm width or girth not otherwise described and applying one coat of Plastic emulsion paint in any tint complete all as specified. (1094 + 1094)*

M & L for 100 mm thick cement concrete as in sub base type D-2, 1:4:8 (40mm graded stone aggregates) (23 + 23)*

M & L for 40 mm thick cement concrete in Floors type B-1, 1:2:4 (20mm graded stone aggregates) finished even and smooth without using extra cement. (23 + 23)*

Material and labour for vitrified ceramic tiles light shade 10 mm thick (square/rectangular) anti skid, area of each tiles not exceeding 0.36sqm, as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. (1057 + 1298)*

All as per Sr. item No 1.037 here-in-above but as in skirting/dado over 10mm thick rendering in CM (1:4)complete all as specified and directed. (39 + 69)*

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade complete over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. (76 + 898)*

M&L for glazed ceramic coloured tiles of size 350x250mmx7mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick back coat CM(1:4) complete all as specified and directed. (198 + 3578)*

All as per item No 1.04 here-in-before but in skirting over 10 mm thick rendering in CM (1:3 ) complete as specified. (2 + 2)*

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube. (58 + 786)*

S&F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement to frame as per specification and drgs. (19 + 236)*

S&F Butt hinges of 100mm size, medium weight, cold rolled, Stainless steel (36 +1356)*

Supply & Fixing 150 mm Aluminium handles, cast type, anodised (24 + 0)*

S&F Aluminium, anodised, barrel tower bolt 125 mm long of extruded section complete. (22 + 22)*

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement. (177 +5738)*

M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete with water proofing compound @ 3% by weight of cement surfaces finished even and smooth without using extra cement. (402 +3724)*

Material & Labour 15mm thick plaster in cement mortar 1:4 on one side of lathing in two layers, 1st layer of 10mm thick and 5mm thick 2nd layer mixed with water proofing compound @ 3% by weight of cement finishing the surfaces even and smooth without using extra cement complete. Note: i) Integral water proofing compound shall be paid and measured separately. ii) Work will be carried out upto tripple storey building therfore quoted rate shall be deemed to be inclusive of scaffolding. (295 + 0)*

M&L 12 mm thick plaster in CM 1:6 on other side of lathing finished even and smooth without using extra cement complete all as specified and directed. (266 + 0)*

S & F wire netting of galvanised steel wire 0.71 mm dia and size of mesh 12 mm fixed with tinned tack of wire staple. (372 + 0)*

M&L for applying two coats of oil bound distemper over a coat of primer on new plastered surfaces of walls including preparation complete all as specified and directed. (168 + 5561)*

M&L for preparing old decorated plastered or unplastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed. (268 + 0)*

M&L for preparing old decorated plastered or unplastered surface of wall and applying one coat of oil bound distemper over and including 1 mm thick wall care putty complete all as specified and directed. (464 + 0)*

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls all as specified & directed. (711 + 0)*

M&L for preparing old surface of plaster or unplastered wall and applying two coats of cement base paint, white or tinted complete all as specified and directed. (157 + 0)*

M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over and including 3mm thick wall care putty filling complete all as specified and directed. (13 + 0)*

M&L for second class hardwood as in scantlings clean sawn timber framed complete. (5.5 + 0)*

S & F Solid PVC Wall Lining/Cladding consisting of 5mm thick Wood Grain printed PVC Sheet inclusive of Solvent Cement and Fixing on PVC Frame as per specification & drawing (520 +0)*

M & L for 2nd class hard wood plain fillets, square, rectangular or triangular in section clean sawn, secured with nails exc 13 and n.exc 25 sqcm. Complete. (287 + 0)*

M & L for 2nd class hard wood plain fillets, square, rectangular or triangular in section clean sawn, secured with nails exc 6 and n.exc 13 sqcm complete (122 + 0)*

S & F 5 mm thick PVC Sheet Fillet of width 35 mm for wall Paneling inclusive of fixing on to wall to make PVC frame as per specification & drawing (606 + 0)*

S & F for 4 mm thick of size 600x600mm HSPC (high pressure steam cured) pre-painted self embossed, classic designed E-Board to be fixed with aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including provisions for light fixtures of any size complete. (846 + 3248)*

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. (1586 + 5636)*

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. (271 + 3368.00)*

S & F for 1 mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings complete (2 + 0)*

Supply and fixing powder coated aluminium work in any position such as door, frames, grills, guard bars and aluminium partitions etc members made out of extruded Aluminium of any section and in any position including jointing cleat fixing complete. (797 + 9262)*

S&F powder coated doors shutters aluminium section weighing 0.55 kg per meter incl necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified. (113 + 0)*

S&F powder coated aluminium window and ventilator shutters, sliding/fixed type without sash bar, aluminium section of size 40 x 18 x 1.29 mm thick including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. (131 + 1022)*

S&F sheet glass 4.8 mm thick ordinary quality and glazing exc 0.5 sqm each pane complete. (71 + 0)*

S&F sheet glass 4 mm thick ordinary quality and glazing exc 0.5 sqm each pane complete. (81 + 0)*

S & F in repair Frosted glass 3 mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane (1 + 215)*

S&F in replacement 10 ltrs capacity PVC valveless syphonic action, twin flush type flushing cistern low level with inlet ball valve float and dual flush type fixed with cast iron brackets of suitable size and providing 32mm dia PVC flush pipe and making all necessary connections complete all as specified. (Make Cera, B1020106 or equivalent in specified makes) (0 + 88)*

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete. (51 + 0)*

S&F 100 mm brass mortice lock ,vertical type 4 lever complete. (52 + 0)*

S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section complete. (84 + 1080)*

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete (34 + 0)*

M&L for preparation of old plastered surface of walls and applying one coat of weather proof exterior emulsion paint. Note: The work will be carried out upto double/triple storey building using scaffolding and rate quoted shall be deemed included in quoted rate . (416 + 3470)*

M&L for preparation of new plastered surface of walls and applying two coat of weather proof exterior emulsion paint over a coat of primer as per manufacturers instruction. Note: The work will be carried out upto double and triple storey building using scaffolding and rate quoted shall be deemed included in quoted rate . (343 + 210)*

M&L for preparation of wood and wood based new surfaces of any description not otherwise described over 10cm girth or width and applying two coats of synthetic enamel paint over a coat of pink primer complete. (31 + 1127)*

M&L for preparation of wood and wood based old surfaces of any description not otherwise described over 10cm girth or width and applying one coats of synthetic enamel paint. (40 + 845)*

S&F in repair for vitreous China wash down water closet pan (pedestal pattern) white with 'P' or 'S' trap, front or back inlet, fixing bolts making all necessary connections (excluding fixing bolts, flushing cistern and flush pipe) (12 + 88)*

S&F in repair PVC soft close WC seat Cover white colour all as specified (11 + 88)*

S&F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual flush type fixed with bracket complete all as specified. (Make Cera, F1020106 or equivalent in specified makes) (12 + 0)*

Supply & Fix in repair Wash basins, Vitreous China (flat back or angle back type) of size 550 x 400 mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing and supply of waste pipe, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed. (12 + 112)*

S&F in repair vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe) complete all as specified and directed. (1 + 0)*

S&F for urinal spreader chromium plated screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe complete. (2 + 0)*

S&F for water Tubes, 15 mm bore 'medium grade' galvanised iron pipe with all fitting and fixed complete to walls and ceilings or laid in floors (123 + 0)*

S&F for water Tubes, 20 mm bore 'medium grade' galvanised iron pipe with all fitting and fixed complete to walls and ceilings or laid in floors (127 + 0)*

S&F in repairs for 15mm bore bib taps cast copper alloy, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule. (12 + 0)*

S&F in repairs for 15mm bore stop valves, angle valves fancy type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions. (37 + 0)*

S & F in repair for cromium plated health faucet with stand 1.0 mtr flexible lead with complete accessories all as specified and directed (12 + 100)*

S&F for pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe. (12 +0)*

Supply and fixing in repair soap dish chromium plated stainless steel approx 160mm x 160mm x 1mm fixed to wall with plugs & CP brass screws complete (12 + 188)*

S & F in repair toilet paper holder of chromium Plated fixed to walls with chromium plated (CP) brass screws (12 +100)*

S&F in repairs 600mm long tubular towel rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screws complete all as specified. (12 + 188)*

S&F PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete. (26 + 376)*

S & F in repair waste coupling of PTMT (half or full threaded) 32 mm dia. (13 + 112)*

S & F in repair 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete. (24 + 264)*

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. (75 + 264)*

S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. (53 + 396) *

S & F 110mm bore PVC (SWR) bends any radius complete. (12 + 44)*

S & F 75mm bore PVC (SWR) bends any radius complete. (20 + 132)*

S & F 110mm bore PVC (SWR) branch piece, single (single Y equal or unequal) complete. (6 + 00)*

S&F rotational moulded polyethylene 1000 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as specified and directed. (4 +112)*

S&F in repair rotational moulded polyethylene 500 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia all as specified and directed. (1 + 0)*

Material & Labour for 75 mm thick cement concrete type C2, 1:3:6, using 40 mm graded aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement including making proper joints of thickness 12 mm and depth 50 mm filled with bitumen mastic with sand and form work with XPM Jali print over top as per specification at an interval of 3m complete all as specified and directed. (473 + 1420.50)*

M & L for cement concrete type C-1, 1:3:6 (20mm graded stone aggregates) as in surface channels and drains (55 + 111.20)*

M & L for Extra forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement (549 + 1876)*

Add or deduct for each 25 mm girth or part thereof over or under 30 cm girth of drain or channel (150 + 600)*

M & L for Pressure grouting of honey combed concrete with cement Slurry by adding CEBEX 100 or Equivalent @ 255 gms/50 Kg of Cement (110 + 1200)*

M&L for anti-termite treating the top surface of filled earth @ rate of 5 litre of emulsion per Sqm of Surface (1096 + 0)*

M&L for anti-termite treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the peimiter wall including drilling and plugging holes etc in apron complete all as specified and directed. (640 + 1834)*

Excavation in post holes (or similar holes) each n.exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed. (122 + 177)*

M & L for Sand Cushioning under pavers block, filling under floors, top & bottom and sides of sewage pipes including watering and consolidation complete all as specified and directed. (11 + 123)*

M & L Machine pressed glossy type vibro compacted precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade fixed with grey cement and no pigment. (216 + 980.50)*

M & L for cement concrete type B1 1:2:4 (20 mm graded aggregate) in cills, coping, kerbs, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed edges (6.70 + 34.60)*

Taking down and refixing shutters of any description exc 1 Sqm and n exc 2 Sqm each. (0 + 440)*

Demolition of Stone slabs and tiles laid, bedded, and pointed in any mortar, of any description or thickness in floors, aprons complete all as specified and directed. (0 + 100)*

M & L for RCC (nominal mix) type A1 1:1.5:3 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (0 + 5.80)*

M & L for RCC (nominal mix) type A1 1:1.5:3 (20 mm graded aggregate) in chajjas, beams, cantilevers, bressummers, lintel over 1.5m span. (0 + 8.35)*

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete. (0 + 195.40)*

S & F 30mm wide continuous (piano) hinges, mild steel, bright finish or electro-galvanised. (0 + 908)*

S & F 35 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete. (0 + 176)*

S & F 35 mm thick 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass. Sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) (0 + 176)*

S & F 100mm size Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete ( 0 + 272)*

Supply & Fixing 150 mm extruded Aluminium handles, fabricated type, anodised. (0 + 1080)*

Supply & Fixing in repair 150 mm extruded Aluminium handles, fabricated type, anodised. ( 0 + 528)*

S&F Aluminium, anodised, barrel tower bolt 150 mm long of extruded section complete. (0 + 352)*

S&F in repair Aluminium, anodised, barrel tower bolt 150 mm long of extruded section complete. ( 0 + 504)*

S&F in repair Aluminium, anodised, barrel tower bolt 200mm long of extruded section complete. ( 0 + 472)*

S & F in repair aluminium (die cast) Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg. ( 0 + 124)*

S & F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate. (0 + 88)*

S & F in repair 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate. (0 + 212)*

M & L for 4mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats all as specified and directed. ( 0 + 398.30)*

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor, overall length of cover plate 140mm (0 + 440)*

M & L for polythene film, 150 micron thick laid over and including one coat of bitumen primer @ 0.3 to 0.5 Kg per Sqm on roof surface. (0 + 1100)*

M & L for PCC 1:5:10 type E2 using 40mm graded brick aggregate as in filling of sunken portion etc. complete. (0 + 19.10)*

M & L for PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in hold fast complete. (0 + 41.40)*

M & L for 25 mm thick cement concrete as in Floors type B-0, 1:2:4 (12.5mm graded stone aggregates) finished even and smooth without using extra cement. ( 0 + 1200)*

M&L for preparation of old plastered surface of walls and applying two coat of weather proof exterior emulsion paint over a coat of primer including complete removal of existing treatment complete all as specified and directed. Note: The work will be carried out upto double/triple storey building using scaffolding and rate quoted shall be deemed included in quoted rate . (0.00 + 448.00)*

M & L for brick work built in CM 1:4 with sub class 'B' brick half brick thick straight or curved on plan to any radius complete all as specified and directed (0 + 47.50)*

S & F as in replacement 19/20 mm dia mild steel chromium plated curtain rod with and including fixing bracket complete (0 + 739.00)*

S & F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. (0 + 511.00)*

S & F in replacement stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. (0 + 150.00)*

Roughening surfaces of old concrete floor/terrace by picking including taking down existing detoriated/decayed tar felt or any treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean and washing down with water to remove dust complete. (0 + 4179.00)*

Material & Labour for screed bed or bedding layer of 10mm thick in cement mortar (1:3) mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof complete. Note: Water proofing compound shall be measured and paid seperately (0 + 621.50)*

M & L for applying water proofing treatment over cleaned roof surface with super thermo APP modified water proofing membrane comprising of following : (a) Applying evenly one coat of cold bituminous primer conforming to [email protected] Kg per square metre on the cleaned plastered surfaces. (b) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforced) with polyester non woven fabric weighing not less than 160 gms per square metre by torch application. The overlap shall not to be less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps. (c) Applying evenly one coat of aluminium paint @ 0.11 litre per square metre over the APP based polymeric membrane. (0 + 621.50)*

Supply only integral water proofing compound ISI marked. (0 + 1083.00)*

M & L for applying cement slurry over concrete surfaces @3kg/sqm. (0 + 3557.00)*

M & L for applying tile adhesive not exceeding 7 mm thick for laying tiles in floor including levelling the floor if required. Make: ferrioscrete (Ferro-1122)/ fevimate, SC-Pedilite/Goldstar of Bal Endura or equivalent ( 0 + 3557.00)*

Material and labour for non skid ceramic tiles light shade 7 to 8 mm thick (square/rectangular) anti skid, area of each tiles exceeding 0.18 Sqm not exceeding 0.38sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. ( 0 + 3318.00)*

All as per Sr. item No 1.153 here-in-above but on skirting/dado over 10mm thick back coat in CM (1:4)complete all as specified and directed. (0 + 638)*

M & L for two coats of aluminium paints to steel surface over a coat of aluminium red oxide primer exc 10 cm width or girth including preparation of new surfaces complete all as specified and directed. (0 + 121)*

Material & Labour for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms in cement mortar (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 20mm thick screed bed (bedding layer) in CM 1:4 complete all as specified and directed. ( 0 + 504.00)*

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose type of soil complete all as specified and directed. (0 + 980.50)*

M&L for preparation of new or previously untreated surfaces of steel and iron work of any description not exc. 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide prime in any tint complete all as specified. (0 + 143.30)*

Supply & fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. (0 + 9251)*

M & L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded stone aggregates) as in Sub base (0 + 132.00)*

Material & Labour for Rendering 5mm thick in CM 1:3 as on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. ( 0 + 300.00)*

M & L for 2mm thick birla white putty/JK white wall care putty on wall complete. (0 + 5561.00)*

M & L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area not exceeding 0.1sq.m Each with tar or coal tar black paint complete (0 + 2.65)*

Material and labour for writing letters or figures with synthetic enamel paint (Block.Roman,Italic or Indian) not exc.30 cm high complete all as specified and directed. (0 + 11.00) *

S&F sheet glass plain 4.8 mm thick ordinary quality and glazing in aluminiumn window n exc 0.5 sqm each pane complete. (0 + 807.00)

Supplying and laying of 16 mm outer diameter CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. (0 + 2200.00)*

Supplying and laying of 20 mm outer diameter CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. (0 + 660.00)*

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, sillls, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good cutting not exc 10 cm girth in brick walls. (0 + 440.00)*

M & L for sealing and grouting the mouth of pipes using Fosroc's non shrink grout Conbextra GP2 or equivalent for 110mm dia complete (0 + 88.00)*

M & L for sealing and grouting the mouth of pipes using Fosroc's non shrink grout Conbextra GP2 or equivalent for 75mm dia complete (0 + 264.00)*

S & F 110mm bore PVC (SWR) branch piece, single (single T equal or unequal) complete. (0 + 92.00)*

S & F 75mm bore PVC (SWR) branch piece, single (single T equal or unequal) complete. (0 + 132.00)*

Supply & Fix in repair Gun-metal, globe or gate valves (ISI Marked) for iron pipe 20mm bore with iron wheel head, screwed both ends complete all as specified and directed. (0 + 176)*

S&F in repairs for 15mm bore bib taps cast copper alloy, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule. (0 + 388.00)*

S&F in repairs for 15mm dia of pipe concealed stop valves of chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions. (0 +188.00)*

S&F in repairs for 15mm dia of pipe angle valves of chromium plated, fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions. (0 + 376.00)*

S&F pillar taps suitable for 15mm dia pipe, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe. Make: ESSCO, Cat No. DLX-508 or equivalent in specified makes (0 + 112.00)*

S & F in repair peg set of six chromium plated fixing with screw. (0 + 264.00)*

S & F in waste coupling of PTMT (half or full threaded) 40 mm dia. (0 + 100.00)*

S & F in repair PVC waste pipe, 32 mm bore, 750mm long for basin. (0 + 112.00)*

Supply & Fix in repair Chromium plated shower roses 125mm size with shower arms fixing to steel pipe or union complete all as specified and directed. Make: ESSCO Cat NO. EOS-542A or as equivalent in specified makes (0 + 112.00)*

S&F in repair Brass chromium plated towel ring round fixed with and including chromium plated brass screws complete all as specified and directed. (0 + 100.00)*

S&F in repairs Grating doom 100 mm dia with waste hole of PTMT (Minimum weight 25 gms) complete all as specified and as directed. (0 + 276.00)*

S&F in repair Corner Sheet glass shelf assembly 300mm radius made of 6mm thick glass with CP metal bracket and CP guard rail fixed with suitable rowal plug & screws complete all as specified and directed. (0 + 300.00)*

S&F glass shelf assembly made of 5.5 mm thick glass, 12 cm wide and 60cm long with CP metal bracket and CP guard rail fixed with suitable rowal plug & screws complete all as specified and directed. (0 + 112.00)*

S&F in repairs sinks with drainage board made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar 1:3 to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm (approx with + 10 mm difference in dimensions as per manufacturers Catalogue) complete all as specified and as directed. (0 + 84.00)*

S & F 110mm bore PVC (SWR) pipes single socketed in any length fixed in retaining wall complete. (0 + 48)*

S & F in repair Fancy glass rectangular edge mirror of size 18 inch x 24 inch (0 + 100.00)*

Dismantling water tanks and removing from site exc 250ltr but n exc 500 ltr complete all as specified and directed. (4.00 + 112.00)*

S & F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles exc 5kg each (0 + 2000.00)*

Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete) set in cement mortar upto 100mm dia complete all as directed. (0 + 660.00)*

Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete) set in cement mortar upto 150mm dia complete all as directed. (0 + 630.00)*

Demolition and breaking up drain pipes (salt glazed, stoneware, AC or reinforced concrete) set in cement mortar upto 200mm dia complete all as directed. (0 + 315.00)*

M & L for DWCPE (SN8) 150mm (ID) diameter pipes laid in trenches (0 + 630.00)*

M & L for DWCPE (SN8) 200mm (ID) diameter pipes laid in trenches (0 + 315.00)*

M & L for anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. (0 + 2980.00)*

M & L for anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same (0 + 3872.00)*

Cutting openings, through brick walls built cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m (0 + 1.82)*

Supply & Fix pressed steel door frame 105x60 mm fabricated from 1.25mm thick sheet with one or more rebated incl necessary fixing lugs hinges, lock strick plate, etc complete all as specified and directed. (0 + 1320)*

Supply & Fix pressed steel door frame 125x60 mm fabricated from 1.25mm thick sheet with one or more rebated incl necessary fixing lugs hinges, lock strick plate, etc complete all as specified and directed. (0 + 440.00)*

Supply & Fix 32 mm Low Density Polyethylene pipes (LDPE) of pressure rating 6 Kgf/Cm2 fixed complete to wall ceiling or in floors complete all as specified and directe. (0 + 105.00)*

Supply & Fix 40 mm Low Density Polyethylene pipes (LDPE) of pressure rating 6 Kgf/Cm2 fixed complete to wall ceiling or in floors complete all as specified and directe. (0 + 105.00)*

Supply & Fix 50 mm Low Density Polyethylene pipes (LDPE) of pressure rating 6 Kgf/Cm2 fixed complete to wall ceiling or in floors complete all as specified and directe. (0 + 105.00)*

Material & Labour for three coats White washing on wall including preparation of new surfaces complete all as specified and directed (0 + 250.00)*

Material & Labour for three coats White washing on ceiling including preparation of new surfaces complete all as specified and directed. (0 + 100.00)*

Material and labour for preparation of old decorated plastered surface of walls and applying one coat of white wash, complete all as specified and directed. (0 + 1100.00)*

Material and labour for preparation of old decorated plastered surface of ceiling and applying one coat of white wash, complete all as specified and directed. (0 + 250.00)*

S & F Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work with 12 mm dia square / round bar conforming to Fe-290 (Gde E-165). (0 + 400.00)*

Disoconnecting existing tanks of capacity 1000 ltr, setting aside or lowering if required for repairs and clening the complete inner surface by rubber/nylon scraper to remove sludge/silt and washing with bleaching powder solution and then clean with clear water etc. and hoisting reconnecting and re-fixing in position (0 + 20.00)*

S & F Brass Elbow suitable for 16 mm outer diameter CPVC pipe complete all as specified and directed. (0 + 200.00)*

Supply and fix Stainless steel sections (bars, square bars, pipes, plates, sheets) of grade SS-304 including fabricating installing, scafolding, grouting and embedding in concrete and screwing etc. Fabrication of grill or railing as per size and pattern approved by Engr-in-Charge.complete all as specified and directed. (0 + 361.00)*

S & F as in replacement shower arm 15mm size, 195mm long with bend of 45 degree with flange of chromium plated. (0 + 112.00)*

M&L for applying two coats of oil bound distemper after and including complete removal of existing treatment of old plastered surfaces of walls complete all as specified and directed. (0 + 11729.00)*

S&F in repairs sinks without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar 1:3 to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm (approx with + 10 mm difference in dimensions as per manufacturers Catalogue) complete all as specified and as directed. (0 + 12.00)*

S&F in replacement stainless steel kitchen plate rack of size 750mm x 600mm x 250mm (approx with + 10 mm difference in dimensions as per manufacturers Catalogue), thickness of stainless steel sheet shall not be less than 1.00 mm fixed with CP cntilever brackets, complete all as specified and as directed. (0 + 100)*

S & F in repair wall mounted EWC with flushing cistern and all accessories Make: Hindware catalogue No.20109 or equivalent in specified makes (0 + 24.00)*

Material and labour for outdoor vitrified tiles n exc 0.38 Sqm, 12-15 mm thick with double bull nosing tread/steps as in staircase set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. (0 + 695.00)*

M & L for outdoor vitrified tiles n exc 0.38 Sqm, 12-15 mm thick, as in staircase riser laid and jointed with grey cement slurry mixed with pigment to match the shade of the tiles over and including 10mm rendering in CM 1:4 complete all as specified and directed. (0 + 9.00)*

Dismantling posts or struts (wood, steel or R.C.C) any section, including taking out embeded portionand making good disturbed ground Posts embedded in Natural ground. (0 + 30.00)*

Dismantling posts or struts (wood, steel or R.C.C) any section, including taking out embeded portionand making good disturbed ground Posts embedded in concrete (0 + 30.00)*

Dismantling of fencing wire mesh of any type and size ( 0 + 36.00)*

Supply & fix mild steel work angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed. (0 + 446.00)*

Supply and fix MS galvanised steel wire chain link fencing of wire mesh nominal pitch of wire not exc 100mm, plain wire, dia of each wire each way exc 2.5mm including line wires, with standard rails, straining bolts, including provision of binding wire complete all as specified and directed. (0 + 276.00)*

M&L for MS bars 10mm dia and over, cut to length, bent to shape required for securing/supporting & tightening chain link fencing in position. (0 + 281.00)*

Supply and fix 12mm dia of neck Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm and not exc 10cm long complete all as specified and directed. (0 + 12.00)*

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement. (0 + 232.00)*

M &L for PCC 1:3:6 (40mm graded aggregate) type C2 as in foundation complete all as specified and directed. (0 + 6.75)*

M & L for random rubble uncoursed stone walling well bounded, beded and solidly hearted built in cement mortar 1:6 complete all as specified and directed. (0 + 38.00)*

M & L for random rubble uncoursed stone walling (except stone) well bounded, beded and solidly hearted built in cement mortar 1:6 complete all as specified and directed. (0 + 7.50)*

Material & Labour for precast cement concrete type C1 ( 1:3:6, using 20mm graded crushed stone aggregates) as in bond stones set in cement mortar 1:6 including formwork complete all as specified and as directed. ( 0 + 2.00)*

Hand packing, except material (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level (0 + 5.00)*

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling uncoursed or brought upto courses in hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc. 20 mm to block in course masonry of lime or sand stone complete all as specified and directed. (0 + 30.00)*

Material & Labour for raised pointing to random rubble masonary uncoursed or brought upto courses in CM 1:4 complete all as specified and directed. (0 + 10.00)*

E/M Items

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete. (1159.00 + 4286.00)*

M&L for Point wiring for One light/fan/bell point controlled by one, one way switch complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed. (609.00 + 0)*

All as per item No- 2.002 here-in-before but for One 3 pin socket outlet 5 Amps on the same board with other switches. (50.00 + 0)*

All as per item No- 2.002 here-in-before but for One 3 pin socket outlet 5 Amps on the switch socket combination on independent board. (380.00 + 0)*

All as per item No- 2.002 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board. (120.00 + 0)*

S & F for Switch piano flush type single pole, one way 6A complete (624.00 + 1412.00)*

S & F for Socket outlet, 2 in 1, 5 pin 5A flush type (50.00 + 268.00)*

S & F for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type (120.00 + 324.00)*

S & F for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc. (83.00 + 268.00)*

S & F for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed. (172.00 + 1668.00)*

S & F for bell push, flush type, 5Amps (35.00 + 76.00)*

S & F in replacement Electric Bell , AC 230 volts, single pole musical type (35.00 + 88.00)*

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB complete. (35.00 + 0)*

S & F sub main wiring with two runs of 2.5 Sq mm and one run of 2.5 Sq mm for earth wire with FR PVC insulated multi standard copper conductors of , 1100 volts grade, drawn through and including PVC double locked Casing & caping including taking down any type of sub main wiring complete. (Note: Two runs of main wire and one run of earth wire with 1 run of PVC casing /caping shall be measured as single unit.) (800.00 + 0)*

S&F sub main wiring with two runs of 4.0 Sq mm and one run of 4.0 Sq mm for earth wire with FR PVC insulated multi standard copper conductors of , 1100 volts grade, drawn through and including PVC double locked Casing & caping including taking down any type of sub main wiring complete. (Note: Two runs of main wire and one run of earth wire with 1 run of PVC casing /caping shall be measured as single unit.) (650.00 + 0)*

S&F sub main wiring with two runs of 6.0 Sq mm and one run of 6.0 Sq mm for earth wire with FR PVC insulated multi standard copper conductors of, 1100 volts grade, drawn through and including PVC double locked Casing & caping including taking down any type of sub main wiring complete. (Note: Two runs of main wire and one run of earth wire with 1 run of PVC casing /caping shall be measured as single unit.) (400.00 + 0)*

S & F for Lamp holder, PVC/ Polycarbonate type with PVC round/square block including 9 watt LED lamp suitable for lamp holder fittings. (140.00 + 288.00)*

S & F 20W LED, 4', Wall mounted LED batten, with LED single or double side connection, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 mm square 3 core from ceiling rose to the light fitting. Make : Havells Cat No LHFXCENNTN1W020(batten) & LHLDDCXCML8Q020(LED Tube) or equivalent in specified makes (50.00 + 972.00)*

S & F 09 watt LED, 2' tube light, Wall mounted with polycarbonate housing/ batten. Make : Havells Cat No LHEXBLP7IN1W009 or equivalent in specified makes. (12.00 + 36.00)*

S & F LED 1x20W Security light fitting, drawn through including 1.2m GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed. Make:- Havells Endurapearl SL20WLLED757SASYTOPCMP or as equivalent in specified makes (12.00 + 0)*

S & F 42 watt LED, 2'x2' recess mounted ceiling light fitting extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic drive etc. with all accessories internally pre wired (200.00 + 0)* Make: CTLRN-36-FO-CDL or equivalent in specified makes.

S & F table focus light 8W, hanging type, white led lamp with all accessories complete all as specified and as directed. (7.00 + 0)*

S & F Map focus/spot light 10W, white led fitting with all accessories complete all as specified and as directed. (25.00 + 0)*

S & F LED Panel 15 Watt round type mounting White/Warm colour ceiling light fitting extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic drive etc. with all accessories internally pre wired (30.00 +0)* Make: HPL Cat No HPLLEDRP15(CW) or as equivalent in specified makes

S & F MCB Distribution board double door type TPN 4 way, sheet steel, powder coated, with 200 Amp rated bus bar neutral link & earth bar etc. for fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. (5.00 + 0)*

S & F MCB TPN 63 Amps, 415 volts, 50 Hz , 'C' series incl taking down old unsv MCB complete all as specified and as directed. (5.00 + 0)*

S & F MCB Distribution board double door type SPN 4 way, sheet steel, powder coated, with 200 Amp rated bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. (12.00 + 12.00)*

S & F for MCB Distribution board double door type SPN 8 way, sheet steel, powder coated, with 200 Amp rated bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. (36.00 + 152.00)*

S & F MCB SPN 40 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed (50.00 + 188.00)*

S & F MCB SP 6-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed. (380.00 + 1528.00)*

S&F ceiling fan 1200 mm sweep, 5 star rating high speed, including suitable size of fan hook and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and as directed. (83.00 + 0)*

S&F Exhaust fan, metallic body, AC single phase 230/ 240 volts of size 250 mm sweep with louvers shutter including anchor bolt of suitable size for fixing arrangement and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and as directed. (15.00 +0)*

S & F 4 mm dia earthing continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and as directed. (26.00 + 0)*

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion and taking out old earthing plate complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber with CI cover plate 10mm thick including angle iron frame , funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately. (iii) Test points shall be made of GI strip 32x6 mm bridge type mounted on insulators, where ever applicable (28.00 + 44.00)*

S & F MCCB 4 Pole, 415 V, Adjustable type, 400 Amps with breaking capacity 36 KA taking down old unsv MCCB complete. (5.00 + 0)*

S & F MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 KA taking down old unsv MCCB complete. (4.00 + 0)*

S & F MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA taking down old unsv MCCB complete. (10.00 + 0)*

S & F MCCB 3 Pole, 415 V, Adjustable type, 125 Amps with breaking capacity 36 KA taking down old unsv MCCB complete. (5.00 + 0)*

S & F MCCB 3 Pole, 415 V, Adjustable type, 25 Amps to 100 Amps with breaking capacity 36 KA taking down old unsv MCCB complete. (4.00 + 0)*

S & F VTPN distribution board double door 6way suitable for MCCB as incomer and MCB as outgoing including MCCB (incomer) 250 Amps, 4 pole, 25 KA, 415 Volts including taking down old unserviceable DB complete all as specified and as directed. (6.00 + 0)*

Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 240 sq mm, 3.5 core complete . NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items. (245.00 + 0)*

All as per item No 2.041 here -in -before but with 150 Sqmm 3.5 Core (85.00 + 0)*

All as per item No 2.041 here -in -before but with 120 Sqmm 3.5 Core (150.00 + 0)*

All as per item No 2.041 here -in -before but with 95 Sqmm 3.5 Core (540.00 + 0)*

All as per item No 2.041 here -in -before but with 70 Sqmm 3.5 Core (120.00 + 0)*

All as per item No 2.041 here -in -before but with 50 Sqmm 3.5 Core (25.00 + 180.00)*

All as per item No 2.041 here -in -before but with 35 Sqmm 3.5 Core (265.00 + 950.00)*

All as per item No 2.041 here -in -before but with 25 Sqmm 3.5 Core (60.00 + 00)*

All as per item No 2.041 here -in -before but with 16 Sqmm 3.5/4 Core (255.00 + 0)*

All as per item No 2.041 here -in -before but with 10 Sqmm 3.5/4 Core (250.00 + 0)*

M&L for clean river sand cushioning under ground cable including spreading and punning down desired thickness complete all as specified ans as directed. NOTE:Only punned thickness shall be measured for payment purpose. (146.00 + 74.50)*

M&L for laying brick sub class 'B' (locally available best quality) burnt bricks for cable protection laid in dry and flat abutting each other with gaps not exceeding 10mm complete. (15687.00 + 8000.00)*

M&L for spray painting to existing panel LT Panel board (Inner& outer) with 2 coats of synthetic enamelled paint of size 2000mmx1500mmx600mm after rubbing and cleaning of existing paint all as specified and as directed. (10.00 +0)*

M&L for Phase indicator lamp neon type RYB (Set of three) -01 Set including taking down old unserviceable phase indicator lamp all specified ansd as directed. (27.00 + 0)*

M&L for welding in repair n exceeding 2.5cm in length, thickness of metal to be welded exc 6mm but not exceeding 9 mm of hinges/ door panels all specified and as directed. (5.00 + 0)*

M&L for Cable Glands made of polycarbonate/ PVC different panels (04Nos of 01 Set) all specified and as directed. (10.00 + 0)*

Supply & laying GI tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 100 mm dia bore including taking out unsv GI tubing complete all as specified and as directed (15.00 + 0)*

All as per item No 2.059 but of size 80mm bore. (30.00 + 0)*

All as per item No 2.059 but of size 40 mm bore. (40.00 + 0)*

All as per item No 2.059 but of size 25mm bore. (60.00 + 0)*

Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories and sunk modular MS box for mounting of fitting alongwith continuous earth wire 1.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly including necessary cutting chase of wall and making good to match with existing surfcae, complete for one light/fan/bell point controlled by one, oneway switch. (0 + 708.00)*

Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly including necessary chase cutting of wall, complete for one 5/6 amps socket outlet on independent board controlled with one, one way switch. (0 + 168.00)*

Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly, complete for one 5/6 amps socket outlet on same board controlled with other switch. (0 + 72.00)*

Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly, complete for one light point controlled by two nos, twoway switchs. (0 +3.00)*

Point wiring with 2.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories alongwith continuous earth wire 2.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly, complete for one 15/16 Amps socket outlet point controlled by one switch on independent board. (0 + 132.00)*

Point wiring with 4 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories alongwith continuous earth wire 4 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly, complete for one 15/16 Amps socket outlet point/AC power controlled by one 15/16 A switch on independent board. Note for Sl Item No. 2.063 to 2.068 :- (i) Modular metal flush box and white cover plate with frame shall be measured and paid separately. (ii) Cutting and Forming Chases in Masonry, Concrete Work, etc. including Cutting and or Leaving Holes/ Recesses, Sinking, etc. and Making Good in Cement Mortar 1:3 for filling up to 20mm and in PCC 1:2:4 (12.5mm Graded Stone Aggregate) for filling more than 20mm including matching with existing colour / paint of surfaces shall deemed to be included in the quoted rate. (0 + 36.00)*

M&L Switch socket combination 2 in 1, 6 Amps flush type, 240 volts, ISI marked complete all as specified. (380.00 + 496.00)*

S&F Switch piano flush type, two way, 5/6 Amps, 240 volts, ISI marked complete all as specified. ( 0 + 38.00)*

S&F Modular switch 6 Amp, 240 Volts, one way, ISI marked complete all as specified and as directed. (0 + 936.00)*

S&F Modular bell push 6Amp, 240 volts & one module complete all as specified. (0 + 12.00)*

S&F Modular switch 16 Amp, 240 volts, one way, ISI marked complete all as specified and as directed. (0 + 132.00)*

S&F Modular switch 6 Amp, 240 volts, two way, 1 module ISI marked complete all as specified and as directed. (0 + 6.00)*

S&F Modular socket 6 Amp, 2/3 pin combined, 2 module, 240 volts, ISI marked complete all as specified and as directed. (0 + 240.00)*

S&F Modular socket 6Amp /16 Amp, 2/3 pin combined, 2 module, 240 Volts, ISI marked complete all as specified and as directed. (0 + 132.00)*

S&F Metal flush box modular for 1/2 module complete all as specified and directed. (0 + 18)*

S&F Metal flush box modular for 3 module complete all as specified and directed. (0 + 132)*

S&F Metal flush box modular for 4 module complete all as specified and directed. (0 + 24)*

S&F Metal flush box modular for 6 module complete all as specified and directed. (0 + 12)*

S&F Metal flush box modular for 8 module complete all as specified and directed. (0 + 48)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 1 module. (0 + 6.00)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 2 module. (0 + 12.00)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 3 module. (0 + 132.00)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 4 module. (0 + 24.00)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 6 module. (0 + 12.00)*

S&F white cover plate with frame (both inner plate & outer plate cover) modular for 8 module. (0 + 48.00)*

S&F ceiling fan 1200 mm sweep, 5 star rating high speed BLDC with remote, including suitable size of fan hook and connecting up with three core twisted flexible copper conductor cable of suitable size upto ceiling rose complete all as specified and as directed. (00 + 352.00)*

S & F 05 W LED, 2' wall mounted polycarbonate batten internally pre-wired with electrinic driver and polycarbonate diffuser with minimum system efficienacy 100 lumens/watt and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sqmm 3 Core from ceiling rose to the light fitting complete all as specified and directed. (0 + 76.00)*

S & F in replacement decorative wall mounted light fitting made up of polycarbonate including 9 W LED lamp with B-22 base including taking down old unserviceable holder fitting. (0 + 524.00)*

S & F Bldg security LED 1x15 W light fitting, drawn through including 1.2m GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos. 10 mm dia including drilling hole as required and connecting up with flexible copper cable of size 0.75 Sqmm 3 core from ceiling rose to the light fitting. (0 + 44.00)*

S & F Bed side light metal body fitting with 5 W LED lamp including all accessories. Make: Philips Cat part No. 919215850324 LED or as equivalent in specified makes (0 + 48.00)*

Supply and fixing BLDC exhaust fan 200 mm (min) sweep polycarbonate blades with built in louvers, AC single phase 230 volts, including electrical connection with twisted three core PVC insulated flexible cord of size 0.75sqmm copper conductor from celing rose, including taking down old unserviceable DB complete all as specified and as directed. (0 + 188.00)*

S & F for MCB Distribution board double door type SPN 12 way, sheet steel, powder coated, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. (0 + 24.00)*

S & F power socket with switch and plate frame suitable for AC of capacity 1.5/2 ton, push type complete all as specified (0 + 188.00)*

Supply, laying and testing of 32 mm nominal diameter High density polyethylene pipes (HDPE) of pressure rating PN4 as per IS : 14333 : 1996 laid in trenches including taking out old complete all as specified and as directed. (0 + 66.00)*

Supply, laying and testing of 40 mm nominal diameter High density polyethylene pipes (HDPE) of pressure rating PN4 as per IS : 14333 : 1996 laid in trenches including taking out old complete all as specified and as directed. (0 + 66.00)*

S & F TV socket complete all as specified and directed. (0 + 88.00)*

S & F Telephone socket complete all as specified and directed. (0 + 88.00)*

M & L for cutting/digging of existing hard surface of cement concrete/bituminous road of size not less than 45cm in width and 20cm deep for laying of GI/CI pipe and making good to disturbed surface by providing PCC or same material after laying pipe line including returning filling complete all as specified and directed. (0 + 42.00)*

M & L for distribution board double door type (for incoming MCCB 100 Amps 4Pole & out going MCBs) DPX 8 ways, steel sheet, powder painted, with bus bar neutral link & earth bar etc. and including taking down old unserviceable DB of any capacity. (0 + 3.00)*

M & L for distribution board double door type (for incoming MCCB 63 Amps 4Pole & out going MCBs) DPX 4 ways, steel sheet, powder painted, with bus bar neutral link & earth bar etc. and including taking down old unserviceable DB of any capacity. (0 + 19.00)*

S & F MCCB 4 Pole, 415 V, Adjustable type, 63 Amps with breaking capacity 16 KA including taking down old unsv MCCB complete. (0 + 19.00)*

S & F MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA including taking down old unsv MCCB complete. (0 + 3.00)*

S&F sub main wiring with two runs of 6.0 Sq mm and one run of 6.0 Sq mm for earth wire with FR PVC insulated multi standard copper conductors of, 1100 volts grade, drawn through and including PVC rigid concealed medium grade conduit with all conduit accessories and making good to disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint to match with the existing surfaces including taking down any type of sub main wiring complete. Note: (i)Two runs of main wire and one run of earth wire with 1 run of PVC conduit shall be measured as single unit. (ii) Cutting and Forming Chases in Masonry, Concrete Work, etc. including Cutting and or Leaving Holes/ Recesses, Sinking, etc. and Making Good in Cement Mortar 1:3 for filling up to 20mm and in PCC 1:2:4 (12.5mm Graded Stone Aggregate) for filling more than 20mm including matching with existing colour / paint of surfaces shall deemed to be included in the quoted rate. (0 + 10800.00)*

Supply & Fix Modular stepped type electronic fan regulator 120W-2 Module (0 + 84)

S & F PVC conduit rigid concealed medium grade pipe 20mm dia with all accessories and including wall chases making good the disturbed surface to match with existing surfaces complete all as specified and directed. (0 + 188.00)*

Point wiring with 1.5 Sq. mm (nominal area) PVC insulated and un-sheathed single core FRLSH copper cable 1100 volts grade with multi-stranded copper conductor in and including PVC rigid concealed conduit (medium grade) and conduit accessories and sunk mild steel terminal boxes with 3mm thick plastic laminated sheet top cover for mounting of fitting alongwith continuous earth wire 1.5 Sq mm PVC insulated and un-sheathed single core FRLSH cable 1100 volts grade with multi-stranded copper conductor and connected to common earth dolly including necessary cutting chase of wall and making good to match with existing surfcae, complete for one light/fan/bell point controlled by one, oneway switch. (0 + 1908.00)*

All as per Sr. Item No.2.108 but for one 5/6 amps socket outlet on independent board controlled with one, one way switch. (0 + 496.00)*

All as per Sr. Item No.2.108 but for one 5/6 amps socket outlet on same board controlled with other switch. (0 + 268.00)*

All as per Sr. Item No.2.108 but for one light point controlled by two nos, two way switchs. (0 +19.00)*

All as per Sr. Item No.2.108 but with 2.5 Sq mm copper conductor for 3 pin 15 Amps socket point controlled by one switch on independent board. (0 + 324.00)*

All as per Sr. Item No.2.108 but with 4 Sq mm copper conductor for one 15/16 Amp socket outlet point/AC power point controlled by one switch on independent board. (0 + 152.00)* Note for Sl Item No. 2.108 to 2.113 :- Cutting and Forming Chases in Masonry, Concrete Work, etc. including Cutting and or Leaving Holes/ Recesses, Sinking, etc. and Making Good in Cement Mortar 1:3 for filling up to 20mm and in PCC 1:2:4 (12.5mm Graded Stone Aggregate) for filling more than 20mm including matching with existing colour / paint of surfaces shall deemed to be included in the quoted rate.

M & L boring of holes under road pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 100mm dia suitable for 0.4 Mpa working pressure for laying cable across the road complete. (0 + 30.00)*

Schedule of Credit

Phoenix Infra

Baka Construction

H P CONSTRUCTIONS