PROVN OF PANTRY AT OFFICER FAMILY ADDN/ ALTN TO SECURITY MAIN GATE PROVN OF SEPTIC TANK AND SOCKAGE PIT PROVN OF LADIES TOILET AND PROVN OF PATIENTS SHIFTING AREA AT BASE HOSPITAL UNDER GE (E/M) BASE HOSPITAL DELHI CANTT-10

Amount

Surface excavation not exc 30 cm deep & averaging 15 cm deep & getting out in soft/loose soil complete all as specified & as directed.

Excavation in trenches not exc 1.50 mtr wide or 10 sqm on plan, 1.50 mtr in depth for manholes & sewage lines, drain, etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in including spreading levelling, watering and well ramming in layers not exc 25 cm thick in any type of soil complete all as specified and directed.

M&L for removing excavated soil out side MOD land complete all as specified and directed.

M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified & as directed.

M&L RCC M-25 Design Mix, using 20 mm graded stone aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slab, under reamed piles and mass concrete complete all as specified & as directed.

M&L RCC M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, post & struts etc complete all as specified & as directed.

M&L RCC M-25 Design Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressumers, lintels over 1.5 m span etc complete all as specified & as directed.

M&L RCC M-25 Design Mix using 20 mm graded stone aggregate as in slab supportred on walls, beams and columns in floors, roof, landings, balconies, canopies, deck slab and in shelves & the like etc complete all as specified & as directed.

M&L RCC M-25 Design Mix using 20 mm graded stone aggregate as in chajjas, rough finished surface complete all as specified & as directed.

M&L for mild steel TMT bars, Fe-500 grade, 10 mm dia and over, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking and binding with MS wire (annealed) not less than 0.9 mm dia or securing with clips compete all as specified and as directed.

All as per srl item No. 11.00 here in before but 6 mm to 8 mm dia bars compete all as specified and as directed.

All as per srl item No. 11.00 here in before but 5 mm dia and over upto and including 10mm dia, as in stirrups spacers and binders compete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, plinth beams, footings, base of columns, pile caps and similar work, vertical or to batter, for rough finished surfaces complete all as shown on drawings, as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surface complete all as specified and as directed.

Use and waste of formwork to soffits of chullah hood, Chajjas, troughs and similar items including edges etc complete all as specified and as directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finished surface complete all as specified and as directed.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surface of concrete complete all as specified and as directed.

Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide, rough finished surface complete all as specified and as directed.

All as per srl item No. 19.00 here in before but width exc 5cm but not exc 10cm compete all as specified and as directed.

Filling under the floors using approved excavated soil including watering, ramming & spreading in layers not exc 25 cm thick compete all as specified and as directed. (Note: Earth obtained from excavation shall be used for filling under floor)

M & L hard core of broken stone or boulder of guage not exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick watered & rammed to a true surfaces compete all as specified and as directed.

M&L brick work with sub class B bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 compete all as specified and as directed.

M&L brick work with sub class B bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 compete all as specified and as directed.

M & L 40 mm thick PCC 1:2:4 type B-0 (12.5 mm graded stone aggregate) as in damp proof course compete all as specified and as directed.

M & L applying evenly a coat of blown type bitumen @ 1.50 Kg/Sqm and blinding with clean dry sand @ 0.05 Cum/Sqm compete all as specified and as directed.

M&L PCC 1:2:4, type B-1, using 20mm graded stone aggregate, as in sub base, finished fair & even to receive top layer etc compete all as specified and as directed.

M & L 15 mm thick rendering on other than fair face of brick wall or concrete surface in cement mortar (1:6) finished even & smooth compete all as specified and as directed.

M & L 10 mm thick rendering in cement mortar 1:4, finished even & smooth, on ceiling, concrete surface compete all as specified and as directed.

M&L 3mm thick wall care putty on newly plastered wall surfaces, trawelled to an even and smooth surfaces including papering the surface, sand papering etc compete all as specified and as directed.

M&L 3mm thick wall care putty on newly plastered ceiling surfaces, trawelled to an even and smooth surfaces including papering the surface, sand papering etc compete all as specified and as directed.

M&L 15 mm thick rendering in cement mortar 1:4 on brick or concrete surfaces on walls, mixed with water proofing (if required) compound finished fair & even without using extra cement compete all as specified and as directed.

Supply only intigral Water proofing compound ISI marked compete all as specified and as directed.

M&L for joint free Non-skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over & including 15mm thick screed bed or bedding layer of cement mortar 1:6 as in flooring complete all as specified and as directed.

M&L for glazed coloured ceramic tiles 350 x 250 x 7 mm/450x350x7mm thick set and jointed in cement slurry paste, laid over & including 15mm thick rendering in cement mortar 1:4, jointed and pointed in white cement mixed with colour pigment to match the shade of tile as in veritical surfaces complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating, out let dia 75mm, including jointing with solvent cement to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends, any radius, with access door including jointing with solvent cement complete all as specified and as directed.

S&F stainless steel, kitchen or laboratory sinks, with drainage board, made out of 1mm thick stainless steel sheet, with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed.

S & F 40 mm dia Waste fittings, brass, chromium plated for sinks, etc with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F PVC waste pipe 40mm bore and 600mm long for Sink complete all as specified and as directed.

S&F chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S&F PP-R gate valve (brass insert) suitable for 20mm outer dia PP-R pipe complete all as specified and as directed.

S&F soap tray stainless steel fixed in the wall, complete all as specified and as directed.

M&L 20mm thick, machine cut granite stone slab (Table rubbed and polished), dressed true and square, in one length not less opening size in Door / window in jambs & cill (provided in two layers with overlap in cill & in single layer in jamb & length shall be as per the length of cill & jamb of Door/windows), etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges rounded or chamfered as directed, set, jointed and pointed in mortar & over & including cement screed bed 20mm thick in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite slab and moulding complete all as specified and as directed.

S&F 5.5mm thick Sheet glass, ordinary quality including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified & as directed.

S&F aluminium grills with and including suitable aluminium anodised frame F/H section as required, 7.5mm thick complete all as specified & as directed. Make: Deco grill design No. DG-104 or euivalent. Model of Make- Jindal/ Hindalco.

S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed to shutter etc complete all as specified & as directed.

S&F powder coated aluminium of various section as required for frame of window/ventilators etc with one or more rebates including jointing cleats for fixing etc. & fixed with cadmium plated screw not less then 300 mm Centre to Centre & ceiling, the joints between frames & Granite/Kota stone with polysulphide sealant as per the manufactures instruction complete all as specified & as directed.

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less then 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21, 100mm long (2Nos.) suitable handle (1 No) complete all as specified & as directed.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing not less then 0.55 Kg/RM including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading, screws etc. complete all as specified & as directed.

S&F brass mortice lock 100mm, 6 lever, vertical type, with duplicate key and handle set complete all as specified & as directed.

S&F Door closer, aluminium body hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified & as directed.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples & aluminium beading as in aluminium shutter complete all as specified & as directed.

Blank

M & L washed stone grit plaster on exterior walls in two layers, under layers 12 mm thick cement plaster 1:4 (1 cement :4 coarse sand) following the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer with 15 mm thick cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand: 2 coloured marble stone chipping 10mm nominal size) including using Colour pigment & marble powder as required in ground in panels with groove all around as per approved pattern including scrubbing and washing the top layer with wire brushes and water to expose the stone chippings complete all as specified and as directed. (Note: Payment for providing grooves shall be made separately under respective item of this Schedule)

M&L forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and as directed.

M&L Providing water proofing treatment with five layered 3mm thick APP (Atatic poly propylele) modified bituminous membrane re-inforced with non woven polyster mat of weight not less than 150 gms/Sqm as centre core and without multiple layers of polythene finished on top and bottom with 7 micron thick flammable polythlene applied by thermo fusion using LPG torch on the bottom portion of the membrane after applying a coat of bituminous primer @ 0.25 Kg /Sqm over roof and finishing the treatment with one coat of bitumen of grade 85/25 @ 1.2 Kg per Sqm and two coat of aluminium paint over APP membrane complete all as specified and as directed. Notes:- (i) An overlap of 100mm & 150mm shall be provided on sides & ends respectively. (ii) Irrespective of lap the net covered area shall only be measured and paid. (iii) The quoted rate shall deemed to be inclusive of primer & APP membrane. (iv) The quoted rate shall deemed to be inclusive of one coat of bitumen of grade 85/25 @ 1.2 Kg per Sqm & two coat of Aluminium paint over APP membrane.

M&L 75 mm thick PCC 1:3:6, type C-1, using 20mm graded stone aggregate, as in plinth protection/hard standing and finished the surface even and smooth without using extra cement complete all as specified and as directed.

S&F 3-layer PP-R (Polypropylene random copolymer) pipes outer dia 20mm, SDR 7.4 & Concealed Pipes SDR 7.4 (PN 16) UV Stabilized and Anti-microbial Fusion Welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed to walls, ceilings or in floors etc complete all as specified and as directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tank, triple layered, food grain plastic (cylindrical, vertical with closed top), hoisted and fixed in position on existing wall, stage, roof or RCC staging complete all as specified in SSR Part-I including supply and connecting tank nipple, float valve etc., making complete connection of inlet and out let pipe, fixing of GI pipe (over flow) & washout to the nearest rain water drain complete all as specified and as directed.

S&F ball brass valves, high pressure, with polyethene float and flynut complete screwed for 20mm bore iron pipe complete all as specified and as directed.

M&L for 18 to 20 mm thick of approved shade granite stone (Zed Balck) (superior Quality) slab (table rubbed and polished as in floors, jambs,steps,cooking platform, shelves etc and the like, over & including 15 mm thick screed bed in cement mortar 1:4 including pointed in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

S&F 12mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F Harrision rail, mild steel, chromium plated with fixing brackets etc complete all as specified and directed.

M&L 10 mm thick rendering in cement mortar 1:3 on brick or stone masonry wall surface & roof slab, finish fair & even mixed with water proofing compound complete all as specified and as directed. (Note: WPC shall be measured & paid separately under respective item of this Schedule.)

M&L for preparation of new plastered surfaces of wall and applying two coats of Oil Bound Distemper over and including a coat of primer on plastered and other surfaces with alkali resistant priming paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of Oil Bound Distemper over and including a coat of primer on plastered and other surfaces with alkali resistant priming paint complete all as specified and as directed.

M&L two coat of acrylic paint exterior grade (100% Acrylic) over and including a one coat of primer including prepartion of newly plasterd external surfaces of walls complete all as specified and as directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for treating the back fill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and as directed.

S&F 18/19mm thick PVC moulded solid board one side prelam for cabinet boxes etc with depth upto 60 cm with self and shutter full size fitted under/ above the kitchen cooking platform and other platform including piono type hinges, knob and magnetic catchers complete all as specified and directed as per drg including provision of fixing arrangement /fixing & fixtures complete all as specified and as directed.

S&F Commercial stainless steel modular kitchen shelf rack, trolley inclunding Rolling drawer, Stainless steel handle and channel having weighing capacity of up to 6 kg complete all as specified and as directed. (Note: Quoted Rate shall be for one complete set of Basket)

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc. 50m complete all as specified and as directed.

M&L Forming jambs in cement mortar 1:6, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete all as specified and as directed.

M & L Plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified and as directed.

M&L for heavy duty coloured (approved colour) fully vitrified paving tiles of size 300mmx300mmx11 to 12mm thick, set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of tiles over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed.

M&L for designer, glass moulded precast concrete interlocking paver block shape, size and colour as approved confirming to IS 15658-2006 of 80 mm thickness M-40 Grade made with grey cement and pigment including sealing the ends using PCC 1:2:4 type B-0, using 12.5mm graded stone aggregate complete all as specified and as directed.

Supply and laying dry sand (25 mm thickness ) for cushioning to interlocking paver block complete all as specified and as directed.

S&F Mild steel Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exc 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layer not exc 25cm in soft/ loose soil including PCC complete all as specified and as directed.

S&F mild Steel work as in tubular trusses, purlins, rafter, vertical post and similar works including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS- 1161 - 1979 Gde-ST-240 including one shop coat of zinc chromate primer paint after necessary prepartion of surface at contractor workshop before fabrication complete all as specified and as directed.

S&F mild steel plate (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes with welded attachment to GI pipe in base/ connections etc. including one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication primer complete all as specified and as directed.

S&F purpose made mild steel bolt 450mm long, 16 mm dia, with hexgonal or square head one end and screwed the other or screwed both ends each screwed is to be fitted with washers and one hexagonal or square nut complete all as specified and as directed.

M&L for Preparation of new or untreated steel surfaces of any description exc. 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide/zinc chrome primer complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour, having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour, having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Excavating over areas not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating over areas exceeding 1.5m deep but not exc 3.00 M deep and getting out in soft/loose soil complete all as specified and as directed.

M&L brick work with sub class B bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 compete all as specified and as directed.

M&L brick work with sub class B bricks straight or curved on plan to any radius inone brick thick honey comb walling built in cement mortar 1:4 compete all as specified and as directed.

M&L 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick surfaces of walls finished the surface fair and even without using extra cement complete all as specified and as directed.

S&F Reinforced concrete pipes,class NP2 lais and jointed complete with collars ware drain pipes laid in trenches and jointed internal dia of pipe 200 mm complete all as specified and as directed.

M&L cement mortar concrete bed to drain pipes in PCC 1:3:6 type C-2 (using 40 mm graded crushed stone agg) incl packing under and haunching against the sides of pipes after they are laid and tested in bores of pipe 200mm dia complete all as specified and as directed.

S&F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers and similar articles exc 5 Kg each complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including form work & weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and as directed.

M&L for loose filling with aggregate of broken bricks of gauge 80 to 150mm in soakage pits, soakage wells complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F Mild steel Framed work as in ornamental type gates including pintle hinges, hold fasts, locking arrangements with ends of bars shouldered and / or riveted or forged into spikes framed guard bar made out of MS rolled section including one shop coat of red oxide primer complete all as specified and as directed.

Demolition of stone slabs laid, bedded and pointed in any mortar and cladding tiles of any description or thickness in floors, aprons, walls, etc and removing the debris off MOD land complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pilllars etc. and precast articles including disposal of demolished material complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc. including raking out of joints, hacking for key, scrubbing down with water etc. any description complete all as specified and as directed.

S&F 4 mm thick Aluminium Composite panel cladding of approved quality and colour as approved by GE, fixed in MS frame at any height, including MS frame of size not exc 0.36 Sqm (using rectangular tubes of size 50.8mmx 25.4mm x 2.9mm thick or square tubes 38mm x38mm x 2.9 mm thick) and filling the joints with all weather silicon sealant including all mouldings, cuttings, etc complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and paving not exc 15cm thickness (below or above ground level) including disposal of all debris and complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4, Type B1, using 20 mm graded stone aggregate, below tiles for levelling of existing surface, mass concrete, etc complete all as specified and as directed.

M&L for vibrator compacted rubber moulded (Lacquer polish) interlocking paver block of shape, size and colour (Red, Yellow, Green and Grey) as approved, confirming to IS 15658-2006, 60 mm thickness, M-35 Grade, made with grey cement and pigment including providing average 25 mm thick cement concrete 1:2:4, type B-1, using 20 mm graded aggregate, as in sides of paver blocks complete all as specified and as directed.

S&F sign board for installation of size 1 mtr x 0.90 mtr made out of ACP sheet with retroit radium sheet, two Nos of ACP sheet fixed parallel to each other, with gap of 20mm and rest on square shape MS made of sheet 3.00 mm thick square type, 2 mtrs long two Nos leg including radium paint complete in blue color and marking the name of installation, place under which sub division in white square border on both sieds of plate with grouting and made PCC 1:2:4 foundation by 20mm graded stone aggregate of size 0.50 x 0.50x 0.75 mtrs complete all as specified and as directed.

S&F stainless steel letters of size 300mm height and 30mm width and fixed with necessary solution to wall surface complete all as specified and as directed.

Supply, laying & testing Salt-glazed stoneware drain pipes, laid in trenches and jointed as specified complete with collars, internal dia of pipe 150 mm complete all as specified and as directed.

M&L cement concrete 1:3:6, type C-2, using 40 mm graded crushed stone aggregate, as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, bore of pipe 150 mm dia complete all as specified and as directed.

M&L for cutting into existing manholes for connecting new mains pipe making good to pipes rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finish and reforming benching as required, internal dia of pipe 150 mm dia complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed, in any length, with rubber ring joints, fixed to walls/Floor complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and as directed.

S & F PVC (SWR) gully trap of 110 mm including setting and jointing with solvent cement complete all as specified and as directed.

M&L high lighter concept glazed ceramic coloured tiles 300x450x7 mm thick on vertical surfaces such as skiting/dado set and jointed in neat cement slurry and pointed in colour cement to match the shade tile over and inclduing 10mm thick rendering in cement mortar (1:6) complete all as specified and as directed.

Supply, laying and testing 15 mm bore galvanised steel water tubing, medium grade, including new GI fittings i.e elbow, socket, plug, socket reducer, tee, union, etc, fixed to walls or laid in floors including cutting chases for concealed water tubing and making good in cement mortar (1:3), cutting not exc 10 cm girth in brick wall/floor etc complete all as specified and as directed.

Supply, laying and testing 20 mm bore galvanised steel water tubing, medium grade, including new GI fittings i.e elbow, socket, plug, socket reducer, tee, union, etc, fixed to walls or laid in floors including cutting chases for concealed water tubing and making good in cement mortar (1:3), cutting not exc 10 cm girth in brick wall/floor etc complete all as specified and as directed.

S&F vitreous china wash basin, colour, flat back, size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including bracket and 32 mm waste fitting of brass chromium plated with long screw small and fly nut complete all as specified and as directed.

S & F brass wash hand basin mixture, fancy type, chromium plated for mixing hot & cold water, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15 mm size PVC connection 450 mm long with brass nut complete all as specified and as directed.

S&F 32 mm bore PVC LDPE, waste pipe with complete fitting for WHB/Kitchen sink/Urinal etc complete all as specified and as directed.

S&F stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed bolt ends for 20 mm bore iron pipe or brass farrule complete all as specified and as directed.

S&F angle stop valve, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed with 15mm bore iron pipe or brass farrule complete all as specified and as directed.

S & F Bib tap, long body, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified and as directed.

M&L point wiring with 1.5 Sqmm , single core , multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 Volts grade, drawn through and including medium grade PVC concealed Conduit of minimum size 20mm as per requirement of site including cadmium plated screws as per ISI, including 3 mm thick phenolic laminated sheet top covers on and including sunk type CI/steel terminal boxes concealed in wall including 1.5 Sqmm size PVC insulated unsheathed copper earth continuity conductor to common earth and connecting to earth dolly for One light/Fan/Bell point controlled by one switch 5 Amps one way single pole complete all as specified and as directed.

All as per item No. 133.00 here in before but one three pin 5 Amps socket out let on independent board complete all as specified and as directed.

All as per item No. 133.00 here in before but one three pin 5 Amps socket out let on same board complete all as specified and as directed.

All as per item No. 133.00 here in before but point wiring of copper cable multi stranded 2.5 Sqmm size for 15 Amps socket outlet on independent board with 2.5 Sqmm size of earth conductor complete all as specified and as directed.

All as per item No. 133.00 here in before but point wiring of copper cable multi stranded 4.00 Sqmm size for geyser/ AC point wiring with 4.00 Sqmm size of earth conductor and PVC conduit size of 25 mm complete all as specified and as directed.

S&F Switch Piano type, white polycarbonate body, single pole, one way 5 Amp, 230 Volts complete all as specified and as directed.

S&F Switch Piano type, white polycarbonate body, single pole, one way 15 Amp, 230 Volts complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15Amp, 230 V, Multipurpose flush type, complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 Amp, 230 V, flush type, complete all as specified and as directed.

S&F stepped type, electronic fan regulator, white polycarbonate body, flush type, 230 V complete all as specified and as directed.

S&F Lamp holder, white Polycarbonate body, with back plate suitable for batten fittings, fixed in position complete all as specified and as directed.

S&F sheet metal enclosure with socket plug top, single pole and neutral enclosure with a two pin earth plug and socket complete with one MCB, Single Pole, capacity 20 Amps, 240 Volts complete all as specified and as directed.

S&F sub main wiring with 2 runs of 4 Sqmm, single core, PVC insulated & unsheathed cable, 1100 Volts grade, with multi stranded, copper conductor, drawn through and including 25 mm dia, concealed, PVC rigid, non metallic conduit, medium grade, as per IS, with all fittings and one run of 4 Sqmm size PVC insulated copper conductor complete all as specified and as directed. (Note:- Two run of cable along with one run of earth conductor including PVC rigid conduit shall be measured as one RM length).

S&F sub main wiring with 2 runs of 6 Sqmm, single core, PVC insulated & unsheathed cable, 1100 Volts grade, with multi stranded, copper conductor, drawn through and including 25 mm dia, concealed, PVC rigid, non metallic conduit, medium grade, as per IS, with all fittings and one run of 6 Sqmm size PVC insulated copper conductor complete all as specified and as directed. (Note:- Two run of cable along with one run of earth conductor including PVC rigid conduit shall be measured as one RM length).

S & F distribution board, double door type, SPN, 12 way, complete including 200 Amps rated bus bar, neutral link, blanking plates etc complete all as specified and as directed.

S & F MCB SP, 240 Volts, 6 Amps to 32 Amp complete all as specified and as directed.

S & F MCB DP, 240 Volts, 40 Amps complete all as specified and as directed.

S&F Surface/Wall Mounted, 20 Watt, integrated LED, 4 feet Fitting, with polycarbonate housing & opal diffuser finish, Integral electronic driver with Output short circuit protection, Surge Voltage Protection of minimum 3 KV and Safety test as per IS15885 Part 2/ Sec 13. Total system Lumen shall be 2000 or above in Cool day Light (6500K), Power factor>0.95, CRI (Ra) >80, System Lumen Efficacy 100 Lm/w, THD(%) < 20, LED with Average life of 50000 Burning hours. Complete with all accessories as required complete all as specified and as directed. Make - Havells Cat part No - LUMILINEBS20WLED865SPCWH or equivalent model of Make- Philips/ Bajaj

S&F Ceiling rose, PVC/ polycarbonate, isolated body type, three terminal, 240 volt, fixed in position & connecting complete all as specified and as directed.

S&F PVC body, exhaust fan 300 mm dia sweep, 900 RPM, 240 Volt, heavy duty, with louver shutter and brackets, connection with flexible PVC copper cable 3 core of size 1.5 Sqmm of length from ceiling rose to exhaust fan including nut bolt and washers of suitable size complete all as specified and directed.

s&f ceiling fan 1200mm sweep, (white), BEE 3/5 star rating, including suitable size of down rod and flexible wire 2 core of size 23 X .0076' and clamps and nut and bolts complete all as specified and as directed.

s&f Water heater (Geyser) of 25 Litre storage capacity, Puro Turbo, AC, Single Phase, 240 Volts, 2 KW with all assessories such as copper tank, assembly, element including plumbing works, geyser mounting , including hot and cold water duty free PVC pipes of size 15mm bore and 60cm long for connection and inlet and outlet pipe line connection, inside the existing wall and making good disturbed surfaces complete all as specified and as directed.

S&F 15mm size brass CP bib tap standard complete all as specified & as directed.

S&F 15 mm size Brass CP Angle valve 2 in 1 complete all as specified & as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete suitable for Hot & cold water complete all as specified & as directed.

S&F 15 mm bore UPVC pipe, fixed on wall, surface, ceiling from existing water supply, with all necessary accessories complete all as specified and as directed.

S&F LED security light fitting, 45 Watt, cast aluminium housing, toughened glass, silicon gasket, high power LED with lens for uniform distribution, pre-wired and electric connection with suitable size of stranded copper flexible PVC insulated wire including 1.5 Metre long, 40 mm bore, medium grade, GI pipe bracket with clamps and bolts complete all as specified and as directed. Make - Havells Cat Part No- ENDURAPEARLNEOSL45WLED757PASYTOPC or equivalent model of Make- Philips/ Bajaj

Supply and laying or fixing or passing through pipe, 1100 Volts grade, heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16.00 Sqmm, 2 core nominal cross section in service connections complete all as specified and as directed.

M&L Earthing complete with galvanised Iron earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtrdeep below GL) with top edge of the plate not less than 1.5 metre below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate with using 4mm dia GI wire as earth wire electrode welded and revetted to earth plate at one end connected to main DBs of Building at another end GI earth wire encased in and including 15mm bore GI light grade pipe through upper end of earth plate up to main DB of bldg, with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate, MS funnel with wire mesh fixed on water pipe including excavation earth work, Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type BI duly reinforced with MS bars 8mm dia @ 150 mm centre to centre, both ways complete with lifting handle all as shown in electrical plate No 3 of SSR of part-I complete all as specified and as directed.

Removing excavated material from site to a distance not exc 50 mtrs away and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed.

S & F 20 mm bore GI tubing, medium grade, laid in floor/roof, including all GI fitting and making connection with new pipe including proper clamping with MS hooks complete all as specified and as directed.

S&F Gun metal gate valve brass including iron wheel head, screwed both ends suitable for 20 mm bore iron pipe or brass farrule complete all as specified and as directed.

M&L point wiring for modular switches with 1.5 Sqmm, PVC insulated, unsheathed, multistranded, copper conductor Cable, FRLS, 1100 Volt grade, drawn through and including concealed, rigid non-metallic PVC Conduit of minimum 25mm dia or as per site requirement with all fittings, including cadmium plated screws as per IS, including 1.5 Sqmm size, PVC insulated, unsheathed, copper earth continuity conductor, connected to earth dolly, suitable for One light/fan/bell point controlled by one No, 5 Amp, one way switch/bell push complete all as specified and as directed.

S&F modular switch, 1 way, 10 Amp, 1 Module, complete all as specified and as directed.

S & F distribution board double door type, SPN, 4 way, complete including 200 Amps rated bus bar, neutral link, blanking plates etc complete all as specified and as directed.

S & F MCB SPN, 240 Volts, 40 Amps complete all as specified and as directed.

S&F modular cover plate with frame, 1 or 2 module complete all as specified and as directed.

S&F modular cover plate with frame, 3 modules complete all as specified and as directed.

S&F modular cover plate with frame, 4 modules complete all as specified and as directed.

S&F modular metal flush box, 1 or 2 modules complete all as specified and as directed.

S&F modular metal flush box, 3 modules complete all as specified and as directed.

S&F modular metal flush box, 4 modules complete all as specified and as directed.

S&F in replacement suspended Mounted, integrated LED, 4 feet Fitting, 40 Watt, with CRCA white powder coated & opal diffuser finish, Integral electronic driver with Output short circuit protection, Surge Voltage Protection of minimum 3 KV and Safety test as per IS15885 Part 2/ Sec, Total system Lumen not less than 4100 or above in Cool day Light (5700K), Power factor>0.95, CRI (Ra) >80, System Lumen Efficacy>110 Lm/Watt, THD(%) < 10, with Average life of 50000 Burning hours, complete with chain hanging arrengment (2 to 3 Metre height), all accessories as required complete all as specified and as directed. Make : Havells Model No CONSTA1144LP40WLED857SPCWH or equivalent model of Make mentioned in PS.

S&F in replacement pole mounted, post top lantern, 35Watt, with Die-cast alluminium housing, Integral electronic driver, with Output short circuit protection and Safety test as per IS15885 Part 2/ Sec, Epoxy powder coated black outside & white inside aluminum sheet top cover of the housing, supported by 3 Nos, die-cast Aluminium arms, The inner white portion act as a reflector for indirect symmetrical light distribution, total system Lumen not less than 1650 in Cool day Light (5700K), Power factor>0.95, CRI (Ra) >80, , THD(%) < 10 with Average life of 50000 Burning hours, complete with all accessories and suitable GI pipe as required complete all as specified and as directed. Make : Havells Model No ENDURASPRING6PT35WLED757PSYMTOTG or equivalent model of Make- Philips/ Bajaj

S&F PVC body, Exhaust fan 250 mm dia sweep,1200 RPM, 240 Volt with louver shutter, connection with flexible PVC Copper cable 3 core of size 1.5 sqmm of length from ceiling rose to exhaust fan including nut bolt and washers of suitable size complete all as specified and directed.

Vishal Traders