Welcome maint including electrical rewiring with fitting/fixture of officer MD Accn at 39 GTC and defence Enclave Naria at Varanasi under GE (East) Allahabad.

Amount

Taking down chowkats of frames exceeding 1.50 sqm but not exceeding 4.0 sqm each with shutter (without taking off shutters from the frames) each including removing from site complete all as specified and directed.

Taking down chowkats of frames exceeding 1.50 sqm each with shutter without taking off shutters from the frames) each including removing from site complete all as specified and directed.

Taking down shutter not exceeding 1.0 sqm each including removing from site complete all as specified and directed.

Repairs of shutters exceeding 2 sqm each resecuring of easing & adjusting and refixing in same opening complete all as specified and directed.

Repairs of shutters not exceeding 2 sqm each resecuring of easing & adjusting and refixing in same opening complete all as specified and directed.

S&F rolled mild steel sections conforming to Fe-410-W (Gde-E-250 quality-A) as in framing for cooler stand, cladding, glazing and the like including door frames/ chowkats, fixed with angle cleats and connecting plates, etc including necessary welding and reviting as moulded in desired shape complete all as specified and directed.

S&F 35mm thick 2nd class hardwood rail and style plain framed, panelled shutter (two panel) factory made with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F factory made second class hardwood glazed and skeleton shutters 30 mm thick, open rebated and prepared to receive glass, gauze, etc. (with sash bars), divided into square with plain chamfered or rounded ,metred edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. are provided with stiles and rails as specified in SSR Part-I, section 8 clause 8.24(a) complete all as specifed and directed.

S & F factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails. mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F in repair 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F in repair 300mm size stain less steel sliding door bolts, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F butt hinges extruded aluminium alloy with galvanised mild steel 100 mm size type B-21 complete all as specified and directed.

S&F 100 mm size aluminium anodised handles, cast type complete all as specified and directed.

S&F 150 mm size aluminium anodised handles, cast type complete all as specified and directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars dovetailed or welded including two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces, fixed in repairs, complete all as specified and directed.

S&F in repair factory made steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars dovetailed or welded including two coat of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces, fixed in repair complete all as specified and directed.

S & F in repair factory made steel ventilators with top hung shutter including hinges, steel peg stay including two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F galvanized steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with galvanized steel wire steples complete all as specified and directed.

S&F in repair galvanized steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with galvanized steel wire steples complete all as specified and directed.

Material & Labour for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in fixing of hold fasts including necessary form work complete all as specified & directed.

S & F in repair 18mm to 19 mm thick prelaminated block board interior grade two quality, as in cup board shutter and fixed with screw and 6 mm thick teak wood beading all around fixed with fevicol & screw and exposed surfaces of beading finish with polish complete all as specified and directed.

Supply & Fixing continuous piano hinges made with stainless steel pin hinges, width of flaps (when open) is 30 mm bright finish or electro-galvanised finished best quality fixed with steel screws complete all as specified & directed.

S & F 100 mm aluminium anodised hasp and staple complete all as specified and directed.

Supply & Fixing 300 mm long mild steel, ordinary rat tail rod pattern door spring including roller and roller plate fixed on door with screws complete all as specified & directed.

Material & Labour for preperation of new wood or wooden based surface of any description over 10 CM width or girth with sand or emery paper and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete and removing rubbish off from the premises complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick 300mm x 300mm size, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L glazed ceramic coloured tiles 300mm X 200 mm x 7 to 8mm thick, in vertical surface such as skirting, dados, risers to steps, etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L glazed ceramic coloured tiles 450mm X 350 mm x 7mm thick, in vertical surface such as skirting, dados, risers to steps, etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick 600mm x 600mm size, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L full body vitrified coloured tiles 10 mm thick 600mm x 600mm size, laid in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick 400mm x 400mm size, laid in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar including all quions arches dressed stone work etc and excluding ashlar facing dressed stone work etc. complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work (Except Bricks) with old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removing of all rubbish off from the site complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L 5 mm thick rendering in cement mortar 1:3 on concrete surfaces on ceiling, finished fair & even complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L two coats of Acrylic emulsion distemper over a coat of chalk whitening primer including preparation of new plastered surfaces of walls complete all as specified and directed.

M&L three coats of white wash including preparation of new plastered or unplastered surfaces of ceiling complete all as specified and directed.

M&L three coats of white wash including preparation of new plastered or unplastered surfaces of wall surfaces complete all as specified and directed.

S&F in repair galvanised mild steel water tubes,15 mm bore with all fittings, 'medium grade', ISI marked, galvanised, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair galvanised mild steel water tubes, 20 mm bore with all fittings, 'medium grade', ISI marked, galvanised, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed.

S&F in repair rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms) complete all as specified and directed.

S & F in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), complete all as specified & directed.

S&F in repair gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete all as specified and directed.

S&F in repair GI fittings such as nipple, elbows, reducers, Tee, sockets and tank nipples etc 15/20mm size complete all as specified and directed.

S&F in repairs vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with plastic water closet seat cover white closet pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate ) bedding, connection to trap, outgoing flushing pipe, anti sypohonage pipe,100 mm bore 'P' or 'S' of pipe etc complete all as specified and directed.

S & F in repair vitreous China wash hand basin white flat back of size 550 mmx400mm fixed on and fixing of cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe (rigid quality) including fixing of tap etc. complete all as specified and directed. Note :- Pillar tap shall be measured & paid seperately as supply only under respective item of BoQ".

Supply only pillar tap cast copper alloy with capstain heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.

S & F in repair pillar tap cast copper alloy with capstain heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.

S&F in repair chromium plated Brass health faucet for pedestal pattern WC including 1.5 m long flexible pipe and brass chromium plated nuts complete all as specified and directed.

S&F in repair wall mixture 15mm dia brass chromium plated as per existed model complete all as specified and directed.

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe 600mm long, fixed in repair complete all as specified and directed.

Supply & Fixing in repair 32/40 mm dia bore Low density polyethylene pipes (LDPE) and 900 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc for WHB and sink complete as specified & directed.

S & F in repair for 15 mm bore angle valve cast screwed down, high pressure, with crutch or butter fly handle, for iron pipe or for unions complete all as specified and directed. MAKE :- L&K cat No. 0047 or techno-Commercially equivalent model of makes as here-in-after in specified

S&F in repair bib taps cast copper alloy chromium plated with capstan head screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete all as specified and directed.

S& F in repair PVC connections 15 mm, 450 mm length with brass nuts at both ends complete all as specified and directed

S&F brass chromium plated shower rose 90mm to 120 mm size with swivel joints, fixed in repairs complete all as specified and directed.

S&F in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified and directed.

S &F in repairs grating round 100 mm size with waste hole of PTMT (minimum weight 100 gms) complete all as specified and directed.

S &F in repairs dia waste fittings brass chromium plated for glazed ware sinks, basins etc with long screwed shanks and flynuts, flange and bedded in red lead cement and other end fixed complete all as specified and directed.

S & F in repair kitchen Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboaratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including supply and fixing cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling ,32 mm dia PVC waste pipe (rigid quality) and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm, complete all as specified and directed.

S&F in repair chromium plated soap dish recessed type (stainless steel) complete all as specified and directed.

S&F in repair tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified and directed.

Material & Labour for cast iron soil waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors for 75mm bore pipe including taking down old damaged unserviceable pipes and removing from site complete all as specified & directed.

Material & Labour for cast iron soil waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors for 100mm bore pipe including taking down old damaged unserviceable pipes and removing from site complete all as specified & directed.

Material & Labour for cast iron soil waste and vent pipes in any length with or without ears, with cement joints, fixed to wall for 75mm bore pipe including taking down old damaged unserviceable pipes and removing from site complete all as specified & directed.

Material & Labour for cast iron soil waste and vent pipes in any length with or without ears, with cement joints, fixed to wall for 100mm bore pipe including taking down old damaged unserviceable pipes and removing from site complete all as specified & directed.

Supply & Fixed in repair for 100mm bore cast Iron bends any radius diminishing pieces or tapers larger bore measured joint with cement joint complete all as specified & directed.

Supply & Fixed in repair for 75mm bore cast Iron bends any radius diminishing pieces or tapers larger bore measured joint with cement joint complete all as specified & directed.

S&F in repair 75 mm UPVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

Supply & fixing in repair 110 mm bore cast iron vent cowl complete all as specified & directed.

S&F UPVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trnches or in floors, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position in unframed work complete all as specified and directed.

M&L Second class hardwood in scantlings clean sawn timber fixed complete all as specified and directed.

Dismantling of stone slab and stone tiles of any thickness and description in floors or apron laid bedded pointed in any mortar of floor including cement mortar bedding & backing complete and removing of rubbish from site complete all as specified & directed.

M&L for 18-20 mm thick machine cut marble (makrana doongary)stone slab as in window cill, jamb, pillars, kitchen platform , bedded, jointed and pointed with white cement slurry mixed with pigment in kitchen top including cutting, grinding and polishing, over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4 and nosing of the edges half round with granding complete all as specified and directed. NOTE: Stone slabe shall be fixed in two piece directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Material & Labour for 75 mm thick PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in plinth protection including making 12 mm wide joint to the full depth of PCC at the length not exceeding 3.0 mtr and at every change of direction and filling the same with and including bitumen and sand 1:3 by weight complete all as specified & directed.

Material & Labour 40 mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate as in floor finish or base of floor, surface finished even with using extra cement complete all as specified & directed.

Demolition of reinforced Concrete work in any description and in any position and removing rubbish from site as directed by Engineer-in-Charge.

S&F TMT mild steel 8 mm dia over cut to length bent to shape required including cranking bending spirally for hooking for columns hooking and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

Material & Labour for reinforced cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in drain cover, cover slab (for manholes) and similar work including necessary form work and set in CM 1:4 complete all as specified & directed. Note :- Reinforcement shall be measured and paid separately under respective item of BOQs.

M&L for chequered cement concrete tiles with grey cement and no pigments 250mm x 250mm and 25 mm thick, set, jointed and pointed in neat cement slurry in floors, over & including 20 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3kg/sqm comprising of following and testing after completion including taking down of old water proofing treatment from roof/ concrete surfaces and removal to a distance exceeding 250 metre. The water proofing treatment shall consist of following stages :- (a) 10 mm thick plaster/ screed bed in cement mortar 1:4 complete mixed with water proofing compound @ 3% as per manufacturers instructions complete all as specified and directed. Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ". (b) Cleaning roof surface by wire brush, brooming & removing dust & shall be painted with a coat of bituminous primer conforming to IS:3384-1986 @ 0.3 litre per Sqm uniformity complete all as specified and directed. (c) After primer,the entire roof surface applying tack coat of hot blown bitumen grade 85/25 grade conforming to IS 702-1988 @ 1.2 Kg per Sqm pver primer. (d) Over hot bitumen ,laying APP modified polymeric water proofing membrane consisting of 3mm thick weight not less than 3 Kg per Sqm over entire area laid with 100 mm side lap and end lap on prepared surfaces as of manufacture"s technical instruction & sealed complete all as specified & directed. (e) Again the entire roof surface applying tack coat of hot blown bitumen grade 85/25 grade conforming to IS 702 @ 1.2 Kg per Sqm. (f) Tapping with PCC tiles 300x300x20 mm thick laid over 20mm thick of CM 1:4 screed bedding and filling tiles joint with CM 1:3 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified & directed.

S&F in repair mild steel tubing of 25 mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings decorative holder and CP brass brackets (wall to wall or flush to wall) for securing to curtain rod, complete all as specified and directed.

Taking down steel roling shutter pull type for repairing like cleaning the sides [guides] of shutters, suspended shaft, anti guide channel, straightening / rolling shaft and replacement of nut bolts as required for smooth functioning by greasing all moving parts of shutter and re-fixed in same opening or place complete all directed by Engineer-in-Charge.

Supply & Fixing in repair steel rolling shutter [Thickness of lath 1.25 mm steel sheets] push or pull type with out ball bearing including top hood cover, anchoring rod, hasp & staple erected in position as required or fixed at site including preperation of new steel surface and apply one coat of red oxide primer than two coats of synthetic enamel paint on entire surface of shutter complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered surfaces of wall including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of celling including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of wall including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coats of acrylic emulsion distemper complete all as specified and directed. Note: The time difference between one coat and two coat will be decided by Engineering-in-Charge.

M&L for preparation of old decorated plastered surfaces of wall including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coats of acrylic emulsion distemper over and including provision of 1 mm thick wall care putty and one coat of primer complete all as specified and directed. Note: The time difference between one coat and two coat will be decided by Engineering-in-Charge.

M & L for applying one coat of synthetic enamel paint on old wooden surfaces of any description, over 10 cm width or girth including preparation of old wooden surfaces complete all as specified and directed.

M&L for preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synnthetic enamel paint complete all as specified and directed.

S & F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60 cm complete all as specified and directed.

M&L for repairing of concrete surfaces such as chajjas, upward facia, downward facias, ceiling and similar items with plain cement concrete 1:2:4 type B-0 using 12.50mm crushed stone aggregate and/or rendering 10mm thick in CM 1:3 including dubbing coat without using extra cement finished even and fair including neessary formwork complete all as specified and directed.

Material & Labour 40 mm thick PCC 1:2:4 type B-0 using 12.5mm crushed stone aggregate as in roof kerbs or mud stops rounded or chemfered on edges complete all as specified & directed.

S&F Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 300 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts fixed in repairs complete all as specified and directed.

Taking down carefully aluminium/ copper point wiring any type (light, fan, socket or power) complete including all fittings such as switches, sockets, ceiling rose, pendants, holders, regulators etc. and making good disturbed surface of walls/ floor complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FR type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Ditto all as item No. 112 here-in-before but for one light point controlled by one, one way switches complete all as specified and directed.

Ditto all as item No. 112 here-in-before but for one fan point controlled by one, one way switches complete all as specified and directed.

Ditto -all as item No. 112 here-in before but 3pin ,5amp socket out let on the same board with other switch complete all as specified and directed.

Ditto- all as item No. 112 here-in-before but one 3 pin, 5amp socket out let on independent board complete all as specified and directed.

Ditto all as item No. 112 here-in-before but for one light point controlled by two, two way switches complete all as specified and directed.

Ditto all as item No. 112 here-in-before but for one bell point controlled by one bell push complete all as specified and directed.

Ditto all as item No. 112 here-in-before but one 3 pin , 15 Amps switch socket combination on independent board with 4 Sq mm cable multistranded copper conductor complete all as specified and directed.

S & F for switch piano, flush type, 5 amps, single pole , one way , 230 volt complete all as specified and directed.

S & F for switch piano, flush type,15 Amp , 230 volt ,single pole , one way complete all as specified and directed.

S & F for switch piano, flush type, 5 amps, two way , 240 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for 2/3 pin, 5&15 Amp, socket outlet, flush type, 2 in 1 complete all as specified and directed.

Supply & Fixing electric ding dong bell AC operated on 230 Volts complete all as specified & directed.

S&F ceiling rose single phase , PVC poly carbonate , insulated body three terminals ISI marked complete all as specified and directed.

S& F for sheet metal enclousre for MCB DB's SPN, 12 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

S& F for sheet metal enclousre for MCB DB's SPN, 6 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

Supply & Fixing single pole and neutral sheet metal enclosure with two pin and earth plug and socket complete with & including one number MCB SP 20 Amps complete all as specified & directed.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 4 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 20/25 mm dia with all conduit accessories and one run of 4 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 4 Sqmm & one run of 4 Sqmm cable and 1RM of condute shall be measured as one unit run.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 6 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 20/25 mm dia with all conduit accessories and one run of 6 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 6 Sqmm & one run of 6 Sqmm cable and 1RM of condute shall be measured as one unit run.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 10 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 32/40 mm dia with all conduit accessories and one run of 10 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified and directed. Note : - Two run of 10 Sqmm & one run of 10 Sqmm cable and 1RM of condute shall be measured as one unit run.

S&F stepped type electronic fan regulator flush type 230 V, 120 watt, AC single phase complete all as specified and directed.

Supply & Fixing in repair 1x18 watt four feet long decorative box type [Ultra slim] linear LED [6000K] batten light fittings with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed. Make : HAvells cat No LHEXBLP7UN1W018 or techno-Commercially equivalent model in Philips / Wipro/ Bajaj.

Supply & Fixing 1x9 watt Mirror light decorative box type [Ultra slim] linear LED [6000K] batten light fittings with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed. Make : Havells cat No. LHEXAPRP7PN1W009 or techno-Commercially equivalent model in Philips / Wipro/ Bajaj.

Supply & Fixing 1x10 watt Edge Lit Downlight panels [Ultra slim] linear LED [6000K] batten light fittings with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed. Make : Havells/ Philips / Wipro / Bajaj.

Supply & Fixing in repair high efficiency 20 Watt LED retrofit tube rod suitable for fixing in existing fittings complete all as specified & directed by Engineer-in-Charge. Make : Havells/ Philips / Wipro/ Bajaj.

Supply & Fixing angular lamp holder insulated body with back plate suitable for batten fittings complete all as specified & directed.

Supply & Fixing MCB Single Pole 240Volt, 6 to 32Amps,10KA breaking capacity "B" curve ISI marked complete all as specified & directed.

Supply & Fixing MCB Single Pole and Neutral 240Volt, 40 to 63 Amps,10KA breaking capacity "B" curve ISI marked complete all as specified & directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galavanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing and taking down of old ineffective earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe upto 7.5 meter beyond the earth plates electrode and the earth resistance of the whole system shall be as near as possible to 0 but shall not in any case exced Five ohm.)

Supply & Fixing in repair high efficiency 12 Watt LED retrofit lamp B-22 holder base with polycarbonate body and aluminium heat sink warm white complete all as specified & directed by Engineer-in-Charge. Make : Havells/ Philips / Wipro/ Bajaj.

Supply & Fixing Building security / street LED light fitting 45 watt IP-65 protection making electrical connection with 2.5 Sqmm twin core copper wire 1.5 long complete fixed with 40 mm dia MS pipe medium grade bracket [1.2 m long & bent to required shape] and fixed with flat iron 40x6 mm clamp two nos with nut bolts & washers as required fixed to pole or walls complete all as specified & directed. Make : C&S Cat No LTESS15WLED or techno-Commercially in model Philips / Havells / Bajaj/ Crompton.

M&L for Taking out old unserviceable louver shutter of exhaust fan and supply and fixing factory fabricated louver shutter suitable for 300 mm dia with aluminium frame and galvanised tinned sheet not less than 1.0 mm thick and fixing with anchor bolts / fastener complete all as specified & directed.

M&L for Taking out old unserviceable louver shutter of exhaust fan and supply and fixing factory fabricated louver shutter suitable for 380/400 mm dia with aluminium frame and galvanised tinned sheet not less than 1.0 mm thick and fixing with anchor bolts / fastener complete all as specified & directed.

Taking down for repairs electric water heater (geyser) of any type/ capacity with dismantling the accessories carefully after disconnecting the water/electirc connection and transporting to workshop (if required) for repairs and refixing the same in original position after repairs and connecting up the water /electric connections including testing and replacement of following unserviceable spare parts.

S&F heating element square/round/Trianglur or any other type 1500Watts, 230 Volts complete all as specified & directed.

S&F heating element square/round/Trianglur or any other type 2000Watts, 230 Volts complete all as specified & directed.

S& F thermostat auto cut with thermal setting upto 80 degree centigrade 230 volts complete all as specified & directed.

S&F in repair water storage copper vessel of 25 ltr capacity geyser complete all as specified & directed. Make- Bajaj or equivalent

S&F in repair water storage copper vessel of 50 ltr capacity geyser complete all as specified & directed. Make- Bajaj or equivalent

S&F in repair syphon assembly of 25 ltr capacity geyser complete all as specified & directed.

S&F in repair syphon assembly of 50 ltr capacity geyser complete all as specified & directed.

S&F in repair aperture plate assembly of 25 ltr capacity geyser complete all as specified & directed.

S&F in repair aperture plate assembly of 50 ltr capacity geyser complete all as specified & directed.

S&F in repair non return valve 15mm dia complete all as specified & directed.

S&F in repair pressure release valve complete all as specified & directed.

S&F in repair glass wool of 25/50 ltr capacity geyser complete all as specified & directed.

S&F in repair indicator lamp red/green complete all as specified & directed.

S&F in repair drain plug complete all as specified & directed.

S&F in repair ball brass valve 15 mm dia complete all as specified & directed.

S&F heat resistant PVC flexible connection pipe 450 mm long suitable for 15mm dia pipe with brass creamed nipple and nuts heavy duty pressure grade 6 kg/ cm² and temp upto 80 degree centigrade complete all as specified & directed.

M&L for spray painting to geysers of any type / capacity from outside with one under coat and one finishing coat of synthetic enamel paint white in colour and marking MES no with black colour synthetic enamel paint complete all as specified & directed.

M&L for taking out the old thermostat / heating element and refixing the same after descaling/cleaning and making electric connection and calibrating/adjusting to a temprature rating as per manufacturer instrutions complete all as specified & directed.

RVRconstructon

PANDEY TRADERS