TN-04/EE/2024-25 Lot No-05 Renovation work of service road from km 80.400 to km 81.250 of the right track of Anupshahar branch canal.

Amount

Up rooting Jhunds with disposal away from Site

Granular Sub-base (GSB) with well graded material (Table-400.1) by mixin place method Construction of granular sub-base by providing well grade material, spreading in uniform layers with motor grade on prepared surface, mixing by mixer in place method with rotavataor at OMC, and compecting with smooth wheel roller to achive the desired density as per MORD specification 401.

Water Bound Macadam Grading - 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. (SI.No. 405.2)

Water Bound Macadam Grading - 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. (SI.No. 405.3)

Brick Edging on both side of the road of M-150 bricks 7 cm wide 11 cm deep, laid with mud mortar including labour & supply of bricks finished to the required] template and in proper alignment and also including dressing and ramming the excavated earth as directed by the Engineer in charge.

Providing laying Prime coat With Bitumen emulsion (SS-A) on prepared surface of granular base inculding cleaning of road surfafe and spraying prime coat of 0.60 kg/sqm using mechnical means as technical Specification Clause 502.

Providing and applying tack coat with bitumen VG-10 grade using bitumen pressure distributer at the rate of 0.30 kg. per sqm on the prepared granular surface treated with primer & cleaned with hydraulic broom as per technical specification clause 503.

Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen VG-10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheele 80-100KN static roller capacity, finished to required level and grades complete all specified in Manual MORD technical specification clause 508 and as directed by the Engineer in charge.

Providing and applying seal coat by manual means with 80/100 grade bitumen sealing the voids in bitumens surface laid to the specified levels grade and cross fall using type C as per technical Specification Clause 510.

Earth work in filling for repair of ruts, cuts, pote holes, depressions and strengthening of bank includiing lift up to 1.50 m and Lead beyond 195m also with ramming, dressing and manual compaction of surface to the required levels and slope etc. Complete.

Provinding and laying brick on edge soling including all material and labour complete.

Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete with Two or more coats .

mamber singh

ARYA ASSOCIATESS

SHRI SIDDH VINAYAK CONTRACTOR

MUKESH TYAGI

M/s Kapil Kumar Sharma

RADHA KRISHAN ENTERPRISES

M/S BHAWANI CONSTRUCTION CO.

Dinesh kumar jindal

M/S CHAUDHARY ENTERPRISES

Aman Construction