AGE (I)/D-53/20-21

Amount

Excavation in trenches in not exceeding 1.5M wide and not exceeding 1.5M in depth and getting out in hard/ dense of soil complete as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5M above the starting point complete all as specified .

Returning, filling in including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick each layer in any type of soil complete all as specified.

Material and labour for plain cement concrete 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate), as in foundation filling and mass concrete, complete all as specified and directed by Engr-in-charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns etc for flat fair finished surface of concrete complete all as specified and directed.

Formwork to sides and soffits of floor, roof or tie beams etc for flat fair finished surface of concrete complete all as specified and directed.

RCC design mix M-25 using 20mm size graded aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified directed.

RCC design mix M-25 using 20mm size graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

RCC design mix M-25 using 20mm size graded aggregates as in Columns, pillars, piers, posts and struts complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

TMT bars, 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Brick work with sub class old size 'B' bricks straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:4 complete all as specified and as directed .

Rendering 10mm thick plaster in cement mortar 1:4 on fair faces of brick work, finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick plaster in cement mortar 1:4 on other than fair faces of brick work, finished even and smooth without using extra cement, complete all as specified and directed.

Preparation of new plastered wall surfaces and applying two coats of cement base paint, white or tinted over a coat of cement based primer, complete all as specified and directed.

PCC 1:2:4, type B-1, (using 20 mm graded crushed stone aggregate) as in copings, plinth band, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed.

Mild steel work of joist, channel, angle in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming Fe 290 (Grade E-165) complete all as specified and directed.

Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed, complete all as specified.Note:-(Each line wire to be measured)

Supply and fixing mild steel framed work as in door chowkats, gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides) and hanging also fastening and fixing complete all as specified and directed by Engr-in-charge.

Preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

Mild steel framed work such as grills gratings etc with end of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings frame work of water tanks and similar work complete all as specified and directed.

Loose filling with aggregate of gauge 20 to 40 mm in gravel block behind weep holes complete all as specified and directed.

Steel water tubing 80 mm bore, light grade galvanised, as in weep holes complete all as specified and directed.

Material and labour wire netting of galvanised steel wire 1.4 mm dia of mesh size 12mm as in gravel block behind weep holes, complete all as specified and directed.

malghotra construction co

M/S Ajay Kumar Mahajan