SPECIAL REPAIR TO BLGD NOS PR 370 TO PR 373 AND T56 AT SEVOKE ROAD MIL STN UNDER GE SEVOKE ROAD

Amount

Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed.

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Demolition of concrete (reinforced) of any description and in in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete (reinforced) of roofs floors (other than ground floor) beams, straicases, landingss, chajjas and similar suspended work complete all as specified and directed.

Demolition of cement concrete (reinforced) RCC water tank of any description and in in any position not otherwise specifically provided for, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of timer scantling 40 sqcm and over in section in any position in unframed work complete all as specified and as directed.

Dismantling expanded metal or mesh, any thickness, fixed with steel or wood fillets, not exc 4 kg/sqm, complete all as specified and as directed

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m and refixing of old shutter in new chowkhats each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down PVC door or frames with shutter (without taking of shutter from the frames) area n.exc 1.5 sqm each complete all as specified and as directed

Demolition of tiles/cement concrete (un reinforced) including water proofing treatment of any specification from existing roof/terrace n. exc. 15 cm thickness removing rubbish off the premises etc complete all as specified and directed.

Demolition of brickwork built in cement mortar including taking out roots vegetation if any at any position and removal from site, complete all as specified and directed. complete all as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls including raking out joints hacking for key, scrubing down with water etc complete all as specified and directed

Taking up or down 15 mm bore steel water tubing and connections complete all as specified.

Taking up or down 20 mm bore steel water tubing and connections complete all as specified.

Taking up or down 25 mm bore steel water tubing and connections complete all as specified.

Taking down rainwater pipes (any size or pattern) and sewage pipe including all fittings, heads, shoes, bends, swan-necks etc incl;uding cleaning or re-fixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed

Taking down old steel window/ventilators of any description not otherwise specified and in any position complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C1 (20mm graded crushed stone aggregated) as in back filling of pressed steel frame complete all as specified and as directed.

Materials and Labour for 25mm thick cement concrete (1:2:4) type B-0, using 12.5 mm graded crushed stone aggregate as in floor finished even and smooth using extra cement complete all as specified and directed.

Materials and Labour for PCC (1:2:4) type B-1 (using 20mm graded mechanically crushed stone aggregate) as in coping, bed plate, fillets and similar works including rounded or chamferred on edges with necessary from work complete all as specified and as directed.

Materials and Labour for PCC 75 mm thick (1:4:8) type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base of flooring complete all as specified and as directed.

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in, plinth protection footpath and hardstanding finished the surface of concrete fair and even, complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in surface channel and drain complete all as specified and as directed.

Materials and labour for average 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in levelling course over RCC roof surfaces to achieve required slope including making rounded or chamfered on edges mixed with WPC @2% by weight of cement complete all as specified and as directed , (Note : WPC shall be measured and paid separately as supply only)

Materials and Labour for precast cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in cover slabs for drain set on cement mortar 1:6 including formwork complete all as specified and as directed.

Materials and Labour for providing precast cement concret louvers and jallies, 50mm thick (measured sloid) including all mouldings but excluding frame type B-0 , 1:2:4 (using 12.5 graded crushed stone aggregated) set in cement mortar 1:6 complete all as specified and as directed. Note: Precast frame if any shall be measued and paid separately under respective item.

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Materials and Labour for formwork to chullah hoods, chajjas, coocking or other platform, troughs and similar items including edges Complete all as specified and as directed.

Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface.

Materials and Labour for Reinforced cement concrete (nominal mix) 1:2:4 type B-1(20 mm graded crushed stone aggregate) as in beams, cantilevers, lintel over 1.5 m span complete all as specified and directed. (Note: Reinforcement and form work shall be measured and paid separately).

Materials and Labour for Reinforced cement concrete (nominal mix) 1:2:4 type B-1(20 mm graded crushed stone aggregate) as in fins, facias, chajja, lintel etc complete all as specified and directed. (Note: Reinforcement and form work shall be measured and paid separately).

Materials and Labour for Reinforced cement concrete (nominal mix) 1:2:4 type B-0(12.5 mm graded crushed stone aggregate) as in chajja, kitchen platform etc complete all as specified and directed. (Note: Reinforcement and form work shall be measured and paid separately).

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars top and bottom runners, brass handles etc as specified erected in position and securing runners with hold fast and brackets complete all as specified and as directed.

Supply & fixing 0.71mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joint) complete all as specified and as directed.

Materials and labour for preparing of new plastered surfaces of walls and applying two coats of weather resistance acrylic emulsion paint over a coat of primer, complete all as specified and directed.

Materials and labour for preparing of new wooden surfaces of any description over 10 cm width or girth and applying 2 coats of synthetic enamel paint over a coat of pink prmer complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for preparing of old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, design and pattern complete all as specified and directed.

Materials and labour for preparing of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying 2 coats of synthetic enamel paint complete all as specified and directed.

Materials and labour for applying three coats of white wash on new wall surface including preparation of surface, complete all as specified and directed.

Materials and labour for applying three coats of white wash on new ceiling surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of old surfaces of ceiling and applying two coats of white wash , complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat alkali resistant primer applied over 1mm thick wall putty complete all as specified and directed.

Materials and labour for re-writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm height with synthetic enamel paint complete as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for chequered cement concrete tiles 20cm x 20cm/30cm x 30cm size, 25 mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed.

Materials and labour for coloured 450x350x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick RENDERING (backing coat) in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for non-skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non-skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm as in skirting etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick rendering (backing coat) in cement morter (1:4) to receive wall tiles etc, complete all as specified and directed.

Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed.

Materials and labour for Kota stone slab 18-20mm thick in floor laid over and including 15mm thick screed bed or bedding layer of cement morter (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for Kota stone slab 20-25mm thick in floor laid over 15mm thick cement screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for brick work with fly ash bricks modular size straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

Supply and fixing 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing second class hard wood plain solid straight chowkhats and frame wrought framed rebated on the soild, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

Materials and labour second class hard wood in scantling fixed in clean sawn complete all as specified and directed.

Supply and fixing flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F factory made 35mm thick plain, framed panelled shutter (two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm veneered particle board with commerical veneering in both faces. The size of rails and stiles shall be as per IS:1003 (Part-I), kiln seasoned and chemically pressure treated of 2nd class hard wood (Hollock/Sal/Kalasiris), complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood (Hollock/Sal/Kalasiris), Kiln seasoned and chemically pressure treated, glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges, of framing plain, chamfered or rounded, fitted with cut and mitred bends for securing glass etc, sizes of members of shutters as specfied in SSR Part I, Section 8, cluase 8.24 (a) ; supplied and fitted to chowkats complete all as specfied and directed.

Supply and fixing 19mm thick plywood grade BWR as in cabinet all as specified.

Materials and labour for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions. Make:- Green ply industries Ltd/ Century/ Archid.

Extra over rates of 18/19mm thick block board for external teak wood lipping, 6mm thick fixed with nails complete all as specified.

Materials and labour for 1 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions. Make:- Green ply industries Ltd/ Century/ Archid.

Materials and labour for first class hard wood plain fillets. square, rectangular or triangular in section, wrought, secured with nails or brads of sectional area exc 3 sqcm and not exc 6 sqcm complete all as specified and directed. .

Supply and fixing Anodised aluminum section powder coated in partition / frame for door, shutters, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

Supply and fixing stainless steel butt hinges, 100 mm size , complete all as specified and directed.

Supply and fixing stainless steel butt hinges, 75 mm size , complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 200 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 125 mm long, complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 125 mm size , complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 100 mm size , complete all as specified and directed.

Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing Hasp and staple, safety type, aluminium anodised 100 mm including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fixing in reepair continuous (Piano) hinges mild steel bright finish or electro galvanised, width of flaps when open 30mm complete all as specified and directed.

Supply and fixing CP curtain rails 20 mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete all as specified and directed.

Supply and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 4 mm thick figured glass, ordinary quality and glazing with oil putty in squares n.exceeding 0.50sqm in each pane, complete all as specified and directed.

Supply and fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Supply & fixing rolled mild steel Fe 290 Gde-E-165 joist, channel, angle or tee sections fixed independently, without connecting plates etc (cut to ordinary lengths i.e. whiting 20mm of the length indicated) complete all as specified and as directed.

Supply & fixing expanded metal, n .exc 4 kg/sqm cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed.

Materials and labour for rendering 5mm thick in cement morter (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement morter (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement morter (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement mixed with water proofing compound as per manufactures instruction complete all as specified and as directed. (WPC shall be measured and paid separately)

Materials and labour for rendering 15mm thick cement morter (1:4) over RCC roof surfaces to receive roof treatment finished even and smooth without using extra cement mixed with water proofing compound as per manufactures instruction complete all as specified and as directed. (WPC shall be measured and paid separately)

Materials and Labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and as directed.

Materials and Labour for formwork to faces of sides and soffits of floor or roof beams, cantilevers, shelves including supports, overhangs, etc for rough finished flat surfaces of concrete complete all as specified and directed

Supply only Water Proofing Compound of approved make.

Materials and labour for preparation of new/old plastered surfaces of wall and applying 2-3mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for complete removal of existing treatment from wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots including washing down with water etc. applying two coats of oil bound distemper with roller over one coat of primer of approved colour after preparation of surface complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying one coat of Primeseal primer of Dr Fixit or equivalent chemical of Fosroc/ STP Ltd as approved by GE or one coat of Chemstic PDE 600 elastomeric coating (allow to dry for 8 hours) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of Dr Fixit with DFT 100 microns or Shalicryl 215 of STP Ltd or Chemstic PDE 600 elastomeric coatingas as approved by GE (surface shall be allowed to dry for 6-8 hours after one coat before application of next coat) including necessary scaffolding as required at site complete all as specified and directed . Note:- Work shall be executed by the authorised applicator of the manufacturer and contractor to submitt authenticate document on this account.

Materials and labour for complete removal of existing treatment from walls and applying one coat of Primeseal primer of Dr Fixit or equivalent chemical of Fosroc/ STP Ltd as approved by GE or one coat of Chemstic PDE 600 elastomeric coating (allow to dry for 8 hours) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of Dr Fixit with DFT 100 microns or Shalicryl 215 of STP Ltd or Chemstic PDE 600 elastomeric coatingas as approved by GE (surface shall be allowed to dry for 6-8 hours after one coat before application of next coat) including necessary scaffolding as required at site complete all as specified and directed . Note:- Work shall be executed by the authorised applicator of the manufacturer and contractor to submitt authenticate document on this account.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of primer after preparation of surface complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including 2.5mm dia mild steel wire galvanized class 3, @ 60cm centre to entre and fixed to steel or wooden member including 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm)

Refixing 15mm bore old serviceable steel tubing and connections in new or old position (walls, ceiling, floors) including cleaning for re-fixing complete to wall , ceiling or laid in floor including provn of all new fittings all as specified.

Supply and fixing 15 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 20 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 25 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing in repairs, stainless steel sink with drainage board, 1 mm thick for kitchen or laboratoty with plugs, waste pipe, washers, including cantilever cast iron brackets, connecting union to waste pipe etc including bedding in cement mortar to dwarf wall, overall size 915x460mm with bowl size 410mm x 330mm x160mm with 40 dia mm CP waste coupling and PVC waste pipe complete all as specified and directed.

Supply and fixing in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with CP brass bracket guard railing 60cm long complete all as specified and directed.

Supply and fixing kitchen plate rack made out of stainless steel 1mm thick sheet with partition and size of rack 800X250X900 mm with shape and pattern as per sample kept in sample room of GE office complete all as specified and directed.

Supply and fixing 15 mm dia chromium plated sink mixer good quality complete all as specified.

Supply and fixing Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, including one coat of red oxide primer complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item No.123 above, but without glazing bars complete all as specified and directed.

Supply and fixing steel ventilators with top hung shutter including hinges,steel peg stay, including one coat of Zinc Chrome primer complete all as specified and directed.

Supply and fixing Mild Steel flat iron fillets fixed to fly proof steel window shutters with screws or riveted for securing wiring gauze etc and as in wind tiles for roof complete as specified and directed.

S&F in repairs vitreous China EWC white with 'P' or 'S' trap front or back intel any pattern excluding flushing cistern & flush pipe but including plastic water closet seat black closed pattern with flat botton and cover and hinging/fixing arrangement complete all as specified

Supply and fixing in repair 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fixing in repair vitreous china squatting pan "ORISSA" pattern of size 580x440mm white with and including 'P' or 'S' trap with integral foot rests (excluding flushing cistern & flush pipe) including provision of lime concrete bedding and connecting up, complete all as specified and directed.

Supply and fixing in repairs Vitreous China wash hand basin, white, flat back, size 550x400mm with coupling , waste, chain and plug and porcelain stopper, brackets, with and incl 32mm dia 90cm long PVC waste down pipe, but excluding taps complete all as specified and directed.

Supply and fixing in repairs, 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing in repairs, cromium plated Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe, complete all as specified and directed.

S& F in repair 15 mm bore stop cock fancy type, chromium plated reduced body, long shunk, cap (concealed type) screwed down high pressure screwed both ends for iron pipe or for union complete all as specified and directed.

Supply and fixing in repair 15 mm bore basin mixer cast copper alloy with capsten head, chromium plated fancy type screwed down high pressure with letter hot and cold with long screwed shank and flynuts screwed for iron pipe, complete all as specified and directed.

S& F in repair 15 mm bore stop cock/angle cock cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe complete all as specified and directed.

Supply and fixing chromium plated tubular towel rail , 600mm long complete all as specified and directed.

Supply and fixing CP soap dish any type, fixed to plugs with chromium plated brass screws complete all as specified.

Supply and fixing Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

Supply and fixing for 450mm long PVC connections 15mm bore size with PTMT 600mm nuts, complete all as specified and directed.

S&F of PVC connections 15mm size with PTMT nuts of length 600mm

Supply and fixing PVC (SWR) pipes 150mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 150mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fixing PVC (SWR) branch piece single , (Single T) equal or unequal, with access door 110 mm bore complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) branch piece single , (Single T) equal or unequal, with access door 75 mm bore complete all as specified and directed.

Supply and fixing in repairs brass chromium plated, shower rose, 125mm size complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply and fixing ball brass valves of size 25 mm bore high pressure, with polythene float and fly nut, screwed for iron pipe etc complete all as specified and directed.

Supply and fixing in repair 15 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Supply and fixing in repair harrison rails 20mm dia, anodised aluminium, chromium plated with fixing brackets stops , rollers with knobs etc complete all as specified and as directed.

Surface Preparation work prior to water proofing treatment of RCC roofs completely as directed, surface to be free from frost, surface laitance and contamination free from loose aggregate or other sharp protrusions with fairly smooth finish for applicaion of water proof coating primer, the surface thoroughly washed with water including removal of all existing treatment, bituminious membrane, tarfelt.screed concrete etc from RCC roof slab.

Materials and labour for application of waterproofing Coating on RCC roofs with following steps of work to be carried out through authorised person/applicator of manufacturer:- : Providing and applying Fosroc Brushbond Roof Guard, a single component High build fibre Reinforced Acrylic Waterproofing render for roofing system to be applied by brush, at three coats at minimum dry film thickness of 1 mm, which should cure by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2 h

Materials and labour for removing loose , disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, chajja, facia, railling etc, cleaning thoroughly exposed reinforcement by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fixing welded wire mesh of size 100x100 mm of 3 mm dia wire weight not less than 1.37 kg/sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guinting in cement mortar 1:3 minimum thickness 30mm and thereafter rendering 10mm thick plaster in cement mortar 1:3 mixed with water proofing compound @ 3% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces removing the debris from site of work, including material and labour for necessary scaffolding and safety arrangement for guinting work, complete all as specified and as directed. (Note :- The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only)

Materials and labour for special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris from site of work etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture's instructions.Complete. Stage 3:- Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture's instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry for 6 hours before next coats) all as per Manufacturer's instructions. Stage 5:- Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltd all as per Manufacture's instructions. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP all as per Manufacture's instruction. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia medium grade GI spout for draining the surplus water if any . Stage 8:- Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion water tightness of repaired sunken portion and filling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accounted for payment under this item. (b) Depth of sunken portion of WC's/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item. (c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and verticale treated surfaces of sunken portions of WC & Bath.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down carefully old serviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc for kept in store and for later use all as directed (To be measured only when found serviceable in all respects complete for reuse)

Taking down carefully unserviceable sub main wiring of any size/core/type including making good the disturbed surfaces all as directed.

Taking down ceiling fans/exhaust fan of any size,dismantling blades and removing fan and blades to MES store complete all as specified and directed.

Taking down existing unserviceable light fittings and Supply and fixing new surface mounted square, slim elegant downlight panel for indoor application with high aesthetic for soothing light pattern LED Light fittings 15 watts, 230 volts, including driver, necessary fixing arrangement and connecting complete all as specified and as directed.

Materials and labour for concealed point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell complete. NOTE : Cost of making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates. all as specified and directed.One light/fan/call bell point controlled by one switch one way 5 Amps

All as per Item No.169 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.169 above but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Item No.169 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

All as per Item No.169 above but for One light point controlled by two nos two way switches.

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps. (Note :- switches to be used both for new point wiring and old switch boxes of existing wiring)

Supply and fixing Switch piano, flush type, single pole, two way switch 5 Amps. (Note :- switches to be used both for new point wiring and old switch boxes of existing wiring)

Supply and fixing Switch socket combination 3 PIN, 5 Amps flush type.

Supply and fixing Switch socket combination 5 in 1, 3 pin 5/15 Amps flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 25x50mm all as directed. (Note :- Ceiling roses to be used both for new point wiring and old existing wiring)

Supply and fixing Socket outlet 3 Pin, 5 Amp flush type universal, 240 volts, complete all as specified all as directed.

Supply and fixing Bell Push Flush type 5 Amp, 240 volt all as specified.

Supply and fixing Bell Ding-Dong AC 230 V Single Pole complete all as specified and as directed.

Supply and fixing in repair decorative type surface and wall mounted 20 Watt LED batten light fittings, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing in repair decorative type surface and wall mounted 9/10 Watt LED batten light fittings, 2 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

M&L LED street light of capacity 25 watt in Aluminium PDC housing, with IP66 protection complete all accessories with connection PVC copper wire not exc 5 mtr completed all as specified and directed.

Supply, fixing and connecting in repair exhaust fan metal body with louvers shutter, voltage 230V, 50 Hz, Copper winding of sweep 300mm, including drilling holes in wall for fixing and connecting with suitable size copper wire complete all as specified and as directed.

Supply and fixing ventilation fan with louvers, single phase, 230/240 V, of size 200mm sweep polycarbonate body, including making holes on wall & making good the distrubed surfaces with all connecting arrangements complete all as specified and directed.

Supply and fixing ventilation fan with louvers, single phase, 230/240 V, of size 250 mm sweep polycarbonate body, including making holes on wall & making good the distrubed surfaces with all connecting arrangements complete all as specified and directed.

Supply, fixing and connecting in repair BLDC(26W) ceiling fan 230V, 50 Hz, Copper winding of sweep 230mm,, connecting with suitable size copper wire complete all as specified and as directed.

Supply and fixing MCB distrubution board SPN 4 way double door, sheet steel,phosphatised,powder coated with 200 amps bus-bar,neutral link,earth bar and din rail, 415 V ,complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB distrubution board TPN 4 way double door, sheet steel,phosphatised,powder coated with 200 amps bus-bar,neutral link,earth bar and din rail, 415 V ,complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB distrubution board SPN 12 way double door, sheet steel,phosphatised,powder coated with 200 amps bus-bar,neutral link,earth bar and din rail 240 V ,complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB TPN, 415 volts 40 Amps 16 KA breaking capacity, C series, adjustable thermal and adjustable magnetic

Supply and fixing MCB Double pole, 240volts 32 Amps, 10KA rupturing capacity, C series

Supply and fixing MCB, SP, 10KA, 415V, "C" curve, 06-32 A, ISI Marked complete all as directed.

Supply and fixing MCB, SP, 10KA, 415V, "C" curve, 40 A, ISI Marked complete all as directed.

Materials and labour for concealed sub main wiring with two single core stranded copper conductor, FRLS PVC insulated cable 1100V grade, 6 sq mm, drawn through and including suitable size of non-metallic PVC rigid conduit with 6 sqmm copper conductor cable as earth conductor and conduit accessories including connecting up complete all as specified and directed.

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x5 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

Supply and laying or fixing or passing through pipe and connecting UG, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core in replacement of existing cable complete all as specified.

Materials and labour for clear sand cushioning for protection of cable complete all as specified and directed. (only punned down thickness to be measured)

Supply and laying fly ash bricks of traditional size as in cable protection complete all as specified.

Supply and fixing GI pipe 40mm bore medium grade for cable protection complete all as specified and as directed.

Supply and lay in trenches/wall LT UG XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core including making necessary connection complete all as specified and as directed.

Supply and laying or fixing or passing through pipe and connecting UG, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core in replacement of existing cable complete all as specified.

MARWA CONSTRUCTION

LIBERAL ENGINEER CONSTRUCTION

D.D. BROTHERS

SRI SURAJIT SENGUPTA

SHRI JAYANTA GHOSH

Raj Enterprise

M S ALOK SAHA