Improvements to the road and drainage facilities to the Kumaran Nagar 1st main road, 4th cross street, 5th cross street and 10th cross of Kumaran Nagar extension in Lawspet Constituency.

Amount

Code No. 2.8.1 Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Code No. 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 4.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Code No. 4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Code No. 4.3.1 Centering and shuttering including strutting, propping etc. and removal of form work for - foundations, footings, bases for columns

Code No. 10.25.1 Steel work welded in built up sections / framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required all complete.

Code No. 13.16.1 6mm cement plaster of mix - 1:3 (1cement : 3 fine sand))

Code No. 15.2.1 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Code No. 15.3 Demolishing R.C.C work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead

Code No. 5.5 Providing, laying and rolling of built-up spray grout layer over prepared base consisting of a two layer composite construction of compacted crushed coarse aggregates using motor grader for aggregates. Key stone chips spreader may be used with application of bituminous binder after each layer and with key aggregates placed on top of the second layer to serve as a base conforming to the line, grades and cross-section specified ,the compacted layer thickness being 75mm. (As per MoRTH specification, 4th Revision)

Code No. 6.2MO Cleaning of the existing black topped surfaces with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 503.3.1 of MOST specification.

Code No. 6.5E.1.MO Providing and applying tackcoat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on black topped surface bitumen @ 5kg/10sqm.

Code No. 6.11B.MO Providing and laying open graded premix carpet of 20mm thick on prepared surface in a single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6-10 tonne laying manually and rolling with power roller 8-10 tonne but excluding cost of primer/tack coat. As per clause no 509 of MOST specification.

Code No. 6.17.MO Providing and applying premixed seal coat type `B' comprising of thin application of fine aggregate premix with bitumen binder in mini hot mix plant, carriage manually of mixed material and laying and rolling with power roller 8 to 10 tonne. As per clause no 513 of MOST specification.

Code No.NPSR (SE approved rate) Fabrication, supply and fixing of village/informatory name board of size 1.06mts x 0.61mts. The width of the board is tapered at 0.80mts upto 1.06mts to give the triangular shape at one end with high intensity reflective sheeting of required color encapsulation on aluminium sheet of not less than 2mm thick suitably supported and framed with 25mmx 25mmx 3mm AISI 316 grade stainless steel angle and the board frame is supported alround with AISI 316 grade stainless steel pipe of 38.10mm dia (outer dia & 2mm wall thickness). The Village names/street names, lettering and symbols will be provided by High Intensity grade white sheeting. The board is supported by Two Nos. of 63.5mm dia post S.S pipes for 2.0mts height with same dia Dummy plate arrangement at the top. The board frame and post pipes are welded by Tig welding with necessary polishing etc, and M.S pipe of 50mm dia for a length of 35cm will be welded at the bottom of the posts and fixed in a ground pit of size 0.45x045x0.55 mts with P.C.C 1:2:4. Rate including all the materials, S.S welding, Grinding, Polishing, fabrication charges, conveyance etc except Earth work and P.C.C charges, complete.

EZHILAN B

GANESAN