Construction of Fire Station Office Building at Baddi Distt Solan HP SH Providing internal Electrical Installation Balance work

Amount

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface/recessed PVC conduit and suitable G.I. modular box with modular switch, modular plates and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required and approved by the Engineer-in- Charge (only cost of wires, modular switch and modular plates will be paid):- Group C

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable insurface / recessed PVC conduit, with 2-way modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required and approved by the Engineer-in- Charge :-Group "C"

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed PVC conduit and suitable G.I. box, with 2-way modular switch, modular plates, and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required and approved by the Engineer-in- Charge (only cost of wires, modular switch and modular plates will be paid):-Group "C"

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required and approved by the Engineer-in- Charge.

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required and approved by the Engineer-in- Charge.

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required and approved by the Engineer-in- Charge.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required and approved by the Engineer-in- Charge.

2x1.5 Sq mm

2x1.5 Sq mm (wiring in existing conduit)

2 x 10 Sq mm

2 x 10 Sq mm (wiring in existing conduit)

Wiring for circuit / sub-main with 4x16 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.16 Sq.mm. (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required and approved by the Engineer-in-Charge (only PVCconduit has been laid).

Wiring for circuit / sub-main with 4x16 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface/recessed PVC conduit along with 2 No.16 Sq.mm. (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required and approved by the Engineer-in-Charge

Supplying and drawing following size of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required and approved by the Engineer-in-Charge. 3 x 1.5 Sq. mm

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required and approved by the Engineer-in- Charge:-

2 modules (78 mm x 78 mm x 60mm

2 modules (78 mm x 78 mm x 60mm (only modular base and cover plate is to be provided)

12 modules (205mmx135mmx60mm) (only modular base and cover plate is to be provided)

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required and approved by the Engineer-in- Charge.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing suitable size modular plate and cover in recess on existing G.I. Modular box of (140mmx78mmx50mm) size including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing suitable size modular plate and cover in recess on existing G.I. Modular box of (140mmx78mmx50mm) size including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing bakelite batten/angle holder including connections etc. as required and approved by the Engineer-in- Charge.

Supplying and fixing call bell / buzzer, suitable for D.C./A.C. single phase,230 volts complete as required and approved by the Engineer-in- Charge.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required and approved by the Engineer-in- Charge.

Supplying and erection of following depth sheet metal cubical pedestal of suitable dimensions with plus-minus 5 cm variation, made from 1.6 mm thick M.S. sheet duly fabricated in a segregated manner for housing of switch fuse units, by welding each compartment on five sides & front side hinged, complete with locking arrangement, with sufficient No. vertical and horizontal intermediate switchgear housing compartments. The cubical pedestal shall have cable entry box at one or two sides, with epoxy powder coated approved paint and bonding to the existing earth etc. The same shall be erected in the 1:2:4 cement concrete plat-form of suitable dimensions 15 cm high from ground level and 45 cm thick. The cubical pedestal shall be 15 cm from the top of cement concrete plat-form:- 300 mm deep (nominal) as required and approved by the Engineer-in-Charge.

Supplying and fixing sheet metal bus-bar chamber suitable for 100 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 300mm & cross-sectional area (25.4mmx3.17mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (380mmx400mmx150mm) nominal with all accessories including connections, earthing the body etc. as required and approved by the Engineer-in-Charge.

Supplying and fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450mm & cross-sectional area (25.4mmx 4.75mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530mmx450mmx150mm) nominal with all accessories including connections, earthing the body etc. as required and approved by the Engineer-in- Charge.

Providing and fixing following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubicle panel, making connections, etc. as required and approved by the Engineer-in- Charge.

100 Amp. -16 KA

200 Amp. -25KA

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required and approved by the Engineer-in- Charge :-Single pole Cat -A

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required and approved by the Engineer-in- Charge :-63 Amps. Cat-A.

Supplying and fixing following rating, four pole, 415 volts, Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required and approved by the Engineer-in- Charge. 100 Amp Cat-A

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required and approved by the Engineer-in- Charge :-Double door-16 way

Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB /Isolator /RCCB /RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required and approved by the Engineer-in- Charge.

Double door-8 way (8+24),horizontal type

Double door-12 way (8+36),horizontal type

Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.( but without charcoal or coke and salt ) complete as required and approved by the Engineer-in- Charge.

Extra for using salt and charcoal for pipe earth electrode complete as required and approved by the Engineer-in- Charge.

Providing and fixing 6 SWG (4 mm dia.) G.I. wire on surface or in recess for loop earthing as required and approved by the Engineer-in- Charge.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering:- as required and approved by the Engineer-in- Charge :- Armoured cable 150sq. mm (3.5 core)

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size as required and approved by the Engineer-in- Charge :- Armoured cable 150 sq. mm (3.5 core)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc.as required and approved by the Engineer-in- Charge :- Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required and approved by the Engineer-in- Charge:- Exhaust Fan, Heavy duty, (Domestic) 300 mm sweep

Supplying and fixing of fancy wall bracket containing thread type LED lamp holder (s) of all sizes and shapes, complete with all accessories but excluding LED lamp including making connections, testing etc. as required and approved by the Engineer-in- Charge :-Fixed type wall bracket 150 dia, single lamp (Category-A

Providing and fixing SKYLUX surface mounting LED 1x1 luminaries white powder coated CRCA housing with high power LEDs. Seamless front frame with flat white high transmission acrylic cover Product code BZSSQL 18 W WH White Bajaj Make or its equivalent make as required and approved by the Engineer-in- Charge.

Providing and fixing LED tube light 20W (VIVA mini LED batten 4ft) for Surface and pendant applications. Anodized extruded aluminium housing, high transmissitivity diffuser and high lumen output, product code BCLAB 20W of BAJAJ make or its equivalent make as required and approved by the Engineer-in- Charge.

Providing and fixing LED Mirror Light Cat No. LCL-07-CDL aesthetically designed linear mirror light provided with a high output PMMA diffuser for glare free light crompton or its equivalent make as required and approved by the Engineer-in- Charge.

Providing and fixing Sleek Surface Square LED Down light 8 Watt with aluminium die- cast body finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for effcient heat dissipation, product code BGSLO SLEEK SURFACE 8W WH SQ of BAJAJ make or its equivalent make as required and approved by the Engineer-in- Charge.

Supplying and fixing of suitable size phenolic laminated sheet cover in the front of existing concealed fan box with complete in all respect as required and approved by the Engineer-in-Charge.

Providing and Erection of LED lamp 9 watt in the existing fixture as required and approved by the Engineer-in-Charge.

Providing and Erection of LED lamp 11 watt in the existing fixture as required and approved by the Engineer-in-Charge.

Providing and fixing Voltmeter in existing cubical Panel etc. as required and approved by the Engineer-in- Charge.

Providing and fixing Ampare Meter in existing cubical Panel etc.as required and approved by the Engineer-in Charge.

Providing and fixing Indicator in existing cubical Panel etc. as required and approved by the Engineer-in- Charge.

Shyam Radio and Electrical