Provn of guard room and pathway at 39 GTC and roof treatment of certain buildings at Supply Depot Varanasi under GE East Allahabad.

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out any type of soil, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out soft/ loose soil, complete all as specified and directed.

Excavation in trenches exceeding 1.5m but not exc 3.0 m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out soft/ loose soil, complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (40mm graded stone aggregate), as in foundation and sub base, complete all as specified and directed.

Plain Cement concrete 1:2:4, type B-0 (12.5 mm crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.

RCC (design mix) M-25 using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC (design mix) M-25 using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC (design mix) M-25 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC (design mix) M-25 using 20mm graded stone aggregate in Chajjas, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

Formwork to rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed.

Formwork to rough finished sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

Formwork to rough finished square, rectangular, polygonal surface of concrete in sides of pillars, posts, struts, piers, columns and stanchions, complete all as speciifed and directed.

Formwork to rough finished flat (horizontal or sloping) concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceedingeeding 200mm thick, complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges for flat rough finished surface of concrete, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering, complete all as specified and directed.

Hardcore, of broken stone or boulders, of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 25mm thick, as in levelling course, benching etc., and finished the surface even and smooth, complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 (20mm graded stone aggregate), 75mm thick, as plinth protection, and finished the surface even and smooth, complete all as specified and directed.

Non - skid Ceramic, white tiles 7 to 8 mm thick, size of each tile shall be 600mm x 600mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 600mm x 600mm, as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, and including provision of 10 mm thick rendering in CM 1:4, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 450mm x 300mm x 7-8 mm / 300mm x 250mm x 7-8mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:4, complete all as specified and directed.

Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., supplied and fixed, complete all as specified and directed.

Flush shutters 30 mm thick, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing inframe at site as per specification & drawing, complete all as specified and directed.

Glazed and skeleton shutters, 35mm thick, first class softwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured and paid separately.

Butt hinges, 100 mm size, extruded aluminium alloy with galvanised mild steel hinge pin to wooden frame, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 200mm long, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised, 150mm long, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 300mm long, complete all as specified and directed.

Door closer hydraulically regulated, Aluminium die cast, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete, complete all as specified and directed.

Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete as specified & directed.

Brickwork with sub class "B" bricks, straight or curved on plan exceeding 6metre mean radius, built in CM 1:4, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 on other than fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement including three coats of white wash, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement including two coats of acrylic emulsion paint in approved shade over 1mm thick wall care putty, complete all as specified and directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement including two coats of cement base paint, complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces of ceiling, finishing the surface even and smooth without using extra cement including three coats of white wash, complete all as specified and directed.

Rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surfaces, finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top), 1000 litre capacity (ISI embossed), double layered, hoisted and fixed in position all as specified in SSR Part I, including provision of GI nipple for tank, including ball valve high pressure PTMT with epoxy coated aluminium rod and high density plastic ball secured for iron pipe of dia 20mm (minimum weight 210 gram), complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 25mm bore of pipe, complete all as specified and directed.

Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 15 mm bore, complete all as specified and directed.

Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), but including provision of lime concrete bedding, including provision of CI trap ‘P’ or ‘S’ type 100mm size, outgoing flushing pipe 32mm dia and anti-syphonage pipe, complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle, jointing with and including provision of 32mm dia 600mm long flush pipe and connections to pipes and fixing of chain and pull, or lever, if any, complete all as specified and directed.

Vitreous China wash hand basin, white flat back, size 630mm x 450mm white, excluding taps, waste pipe, chain and plug and porcelain stopper but including brackets, including cutting for and pinning in ends of brackets or erecting stand, with out provision of Waste coupling of PTMT 32mm dia (half or full threaded) (Minimum weight shall be 45gms), waste pipe 32mm dia PTMT with inlet and outlet screwed for pipe including necessary packing, union and cap, complete all as specified and directed.

Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms), complete all as specified and directed.

Cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), including brackets, PVC waste pipe suitable for connection to urinal and necessary connection, complete all as specified and directed.

PVC connection 15mm size with brass checknuts and washers on both ends of length 450mm, complete all as specified and directed..

Soap dish, brass chromium plated, of standard size and best quality, complete all as specified and directed.

Grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms), complete all as specified and directed.

PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in trenches or in floors including necessary earth work, complete all as specified and directed..

PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.. Note : Stack clamps for fixing in walls shall be included in the quoted rates.

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in trenches or in floors including necessary earth work, complete all as specified and directed..

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.. Note : Stack clamps for fixing in walls shall be included in the quoted rates.

PVC (SWR) bends / shoe of any radius and 110mm bore, complete all as specified and directed..

PVC (SWR) bends / shoe of any radius and 75mm bore, complete all as specified and directed..

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed..

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, complete all as specified and directed..

PVC (SWR) vent cowl, 75mm bore, complete all as specified and directed.

PVC (SWR) vent cowl, 100mm bore, complete all as specified and directed.

Bib taps, fancy type, cast copper alloy, long body chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, 15mm bore, complete all as specified and directed.

Stop valves, fancy type, cast copper alloy, 15 mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for iron pipe 15mm bore, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Plain cement concrete 1:3:6 type C-2 (40mm graded stone aggregate),75mm thick, as in levelling course, benching, sub base of floor etc., and finished the surface even and rough to receive screed bed, complete all as specified and directed.

Paving tiles of size 300mm x 300mm, 25-30mm thick, with wear resistant coat of approved design laid with cement slurry @ 3 kg/sqm, over 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing of surplus excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and directed.

Supply, laying, jointing and testing of Salt-glazed stoneware drain pipes of grade 'A', internal diameter 150 mm, laid in trenches and jointed with bends and taper bends, any radius complete with collars CM 1:1, complete all as specified and directed. NOTE:- The measurements shall be net as fixed between the fittings without any allowances for cutting and waste. Quoted rate shall deemed to include all necessary extra joints, waste and cutting.

Concrete bed to 150 mm bore drain pipes including forming cradles, in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate), complete all as specified and directed.

Taking down existing water proofing treatment any thickness & removing the debris from the premises to a distance exc 250m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

Providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3 kg per sq.m comprising of the following and testing of following: (a) 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:4 mixed with water proofing compound @ 3% by weight of cement, finished surface even and smooth without using extra cement. (b) One coat of Bitumen primer confirming to IS-3384-1965 @ 0.3 ltr per sqm. (c) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (d) Providing APP modified polymeric water proofing membrane having weight not less than 3 kg per sq.m with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length. (e) Again Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (f) Spread coarse sand over entire bitumen surafce and then topping with cement concrete chequered tiles of size 250mm x 250mm x 25mm laid over and including provision of 15 mm thick screed bed in CM 1:6 and joints shall be pointed with CM 1:3, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Plain Cement concrete 1:2:4, type B-0 (12.5 mm crushed stone aggregate) as in roof padding and misc surfaces using water proofing compound, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing compound, complete all as specified and directed.

Supplying and laying 40mm thick factory made chamfered edge cement concrete paver block of M-35 grade of approved colour, design and pattern as in footpath, parks, lawns, parking, etc of required strength, thickness and size/ shape, made by table vibratory method usng PU mould, laid in required pattern over and including 50mm thick compacted bed of fine sand compacted by using plate vibrator, filling the joints with sand and cutting of paver block as per required size and pattern and sweeping extra sand, complete all as specified and directed.

Supplying and laying factory made kerb stone of M-25 grade cement concrete at or near ground level in position to the required line, level and curvature, jointed with CM 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5mm) including making drainage opening wherever required, complete all as specified and directed.

Preparation of new or previously untreated concrete surfaces over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories, including provision of concealed pressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 3.0 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 sq.mm FRLS type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed for the following:-

(a) One light / fan / bell / exhaust fan point, controlled by one one-way 5Amp switch

(b) One 3 pin, 5 Amp socket outlet point on an independent board.

Switch piano, flush type single pole, one way 5/6 Amp 240 volts, ISI marked, complete all as specified and directed.

Socket outlet, 5 pin, 5/6 Amps 240 Volts, flush type, complete all as specified and directed.

Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal, 240 Volts, complete all as specified and directed.

Ceiling rose three terminal PVC / polycarbonate insulated body, surface bakelite type AC 50 Hz 230V, complete all as specified and directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 2.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for mounting switch socket/ fan regulator including provision of concealed opressed steel terminal box of required size not less than 1.6 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 3.0 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 2.5 sq.mm FRLS type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed.

Sheet metal enclosure for MCB DBs SP, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands, complete all as specified and directed.

MCB, SP, 6 to 40 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

MCB SPN, double pole, 40 Amps, 240 V, complete all as specified and directed.

Pendant holder, ordinary/ bracket/ angular type, comprising brass pins & ring with insulated body lamp holder, complete all as specified and directed.

LED ball lamp of capacity 15 Watt, B-22 holder base with polycarbonate body and aluminium heat sink warm white, complete all as specified and directed.

LED mirror light fitting, 1x9W, 6000K decorative indirect up-down light fitting for mirror and wall light application with extruded polycarbonate environmental friendly energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- E-lite LED Pride Plus- 9 W Cat No. LHEXBLP7IN1W009 of Havells or techno-commercially equivalent model in Philips / CG

LED tube light fitting, 1x20W, 6000K decorative, ultra slim, linear LED lighting fixture with extruded polycarbonate environmental friendly energy efficient complete with all accessories, pre-wired and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp, complete all as specified and directed. MAKE:- E-lite LED Pride Plus- 20 W Cat No. LHEXBLP7IN1W020 of Havells or techno-commercially equivalent model in Philips / CG

Supply, installation, testing and commissioning of desert cooler, electric driven (single phase), having approximate normal air flow of 4000 cum per hour & including submersible pump alongwith provision of suitable accessories as required for sucessful working of cooler, made of MS body not less than 2.5mm thick, complete all as specified and directed.

Building security / street LED light fitting 15 Watt IP-66 protection pressure diecast aluminium body, heat resistant glass, including driver and making necessary electric connection with 2.5 sqmm three core copper wire 1.5m long and fixed on GI pipe (40mm bore having 2 coats of aluminium paint), fixed to pole or on wall, complete all as specified and directed.

Ceiling fan (5 star rating) , 1200mm sweep, copper wound motor suitable for 230V AC supply, with and including fan regulator, 15 mm dia 300mm long hanging rod, device with rubber real and split pins and making necessary connection with ceiling rose with twin core copper wire of suitable size, complete all as specified and directed.

Exhaust fan, heavy duty, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc, complete all as specified and directed.

Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 15mm dia GI pipe 'medium grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation & earthwork, PCC (1:2:4) type B-1 earth chamber and mild steel angle iron frame 25 x 25 x 6 mm and 40mm thick pre-cast RCC cover (1:2:4), type B-1 (using 20mm graded crushed aggregate) mix with 6mm dia MS bars @75mm c/c both ways, mild steel handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe light grade(ISI marked) for watering, etc complete all as shown in electrical plate No.3 of SSR Part-1, connected to earthing test point, including testing on completion, complete all as speciifed and as directed. NOTE:- The quoted rates shall also deemed to include the cost of Earth Test point and earth wire and protection pipe upto 7.5 metre beyond the earth plates electrode.

Spreading of natural, clean and dry river sand in trenches for cable cushioning, upto 25cm thick and punning the sand to 18cm thickness, complete all as specified and directed. NOTE: Punned thickness shall only be measured and paid.

Supply and lay burnt clay fly ash bricks class 'B', modular bricks, laid in trenches for cable protection with length of brick equal to width of trench, complete all as specified and directed.

Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 2.0 core 10 sq.mm, including taking down existing old/ unserviceable cable, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule.

Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 3.5 core 25 sq.mm, including taking down existing old/ unserviceable cable, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule.

GI pipes, light grade, ISI marked, galvanised including short lengths, laid in trenches / fixed to walls / ceilings or laid in floors / laid in ducts / laid under road crossing for cables, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 40mm bore of pipe, including taking down of pipe, complete all as specified and directed. NOTE:- Necessary excavation and earthwork for GI pipe shall be measured and paid separately under respective items of this Schedule.

Drilling through bore hole by trenchless technology without disturbing the existing road for passing of LT cable upto the depth not less than 1 mtr, complete all as specified and directed.

GAYDIN CONSTRUCTIONS

Matrubhoomi Construction

Saraswati Constructions

GANGETIC DOLPHIN