Construction of Two Unit of Staff Quarter at Naokata MPHC in Baksa District under Health_FW Deptt. BTC

Amount

Earth work in excavation by mechanical means(Hydraulic excavator)/ manual means in foundation trenches or drain (not exceding 1.50m in width or 10.00sqm on plain) including dressing of sides and ramming of bottoms, lift upto 1.50m including getting out the excavated soil and disposal of surplus excavated soil as directed withi a lead of 50m

Excavating supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 KM also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from naturalsources : 6 graded stone aggregate 20 mm nominal sizederived from natural sources)

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated (TMT) bars of grade Fe-500 or more.

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated (TMT) bars of grade Fe-500 or more.

Centering and shuttering, propping etc. and removal of form for: Foundation, footings, bases of columns etc for mass concrete

Centering and shuttering, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bresumerss and cantiliver with 12mm tk. Ply

Centering and shuttering, propping etc. and removal of form for: 5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm

Providing and laying in position specified grade of reincorced cement concrete, excluding the cost of cetering, shuttering, finishing and reinforcement- (All works up to plinth level. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from naturalsources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reincorced cement concrete work in walls (any thickness), including attached pilaster, buttresses, plinth and string courses, fillets, columns, pillers, piers, abutments, post and struts etc. above plinth level up to floor level, excluding cost of cetering, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu-ral sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources)

Dry brick on edge flooring in required patern with bricks of class designation 7.5 on a bed of 12mm mud morter including fiiiling joints with jamuna sand with common burnt clay non modular bricks

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in. Cement morter 1:4 (1 cement, 4 Coarse sand)

Half brick masonary work with burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level. Cement morter 1:3 (1 cement, 3 Coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) :

12.65 Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temperHx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 12.65.4 0.56mm Aluminium color profile with center to centerpitch of 175 mm, depth of 46mm, top crest width of41mm, bottom valley width of 80mm, overall profile widthof 1144mm, cover width 1050mm.

12.66 Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : 12.66.1 Precoated/mill finish aluminium Ridges plain(500- 600mm)

Steel work in built up tubular (round, square or ractangular hollow tubes etc) trusses ets. Including cutting, hoisting, fiaxing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washer etc. complete Hot finished welded type tubes

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Finishing walls with water proofing cement paint of required shade New work ( two or more coats applied @ 3.84 kg/m2)

Painting steel work with Delux Multi Surface Paint to give an even shade . Two or more coat applied @ 0.90 lit/10 sqm over an under coat of primer applied @ 0.80 lit/10 sqm of approved brand and manufacture.

62mm thick cement concrete flooring with concrete hardener topping, under layer 50mm thick cement concrete 1:2:4 and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement : 2 graded stone aggregate6mm nominal size) by volume , hardening compound mix @ 2 litre per 50 kg of cement or as per manufacture's specifications. This includs cost of cement slurry, but excluding the cost of nosing of steps etc. complete

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecti ng clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm - - - - - - -- the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) sqm 1117.65

Providing and fixing pressed steel door frames conforming to IS: 4351 manufactureed from commercial mild steel sheet of 1.6 mm thickness, including hinges, jamb, lock jamb, beded and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm presses butt hinges 2.5 mm thick with morter guard, lock strick-plate and shock absorvers as specified and applied a coat of approved steel primer after pre-tretment of the surface as directed. by the Engineer in charge. 10.14.2 Profile C 14.2.2.1 Fixing with adjustable lugs with split end tail to each jamb.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment) Fixing with 15x3 mm lugs 10 cm long embedded in cementconcrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing ISI marked Ioxidised MS sliding door bolt with nuts and screws etc. completed: 300x16mm

Providing and fixing ISI marked oxidised MS sliding tower bolt black finished (Barrel type) with nuts and screws etc. completed: 250x10mm

Providing and fixing ISI marked oxidised MS handles conforming to IS: 4992 with necessary screws ctc. Complete. 125mm

Glass fitting Providing & fitting clear sheet glass beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be reqd size (payment for wooden bead shall be made separately. 2) Area of glass pans exceeding 0.15m2 but not exceeding 0.52m2 b) 4 mm tk.

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources : 6 graded stoneaggregate 20 mm nominal size derived from natural sources) over 75mmthick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including necessary excavation,levelling & dressing & finishing the top smooth.

2.25(a) Excavating supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 KM also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

17.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests each

17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a15 mm CP Brass single hole basin mixer each

17.32 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 Rectangular shape 1500x450 mm each

19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 each

18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 18.12.5 40 mm dia nominal bore metre

18.42 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested : 18.42.1 Up to 6 metres depth

18.42.2 Beyond 6 m and up to 12 m depth

18.42.3 Beyond 12 m and up to 18 m depth

18.43 Providing and placing in position filters of 40 mm diameter G.I. pipewith brass strainer of approved quality

18.45 Providing and placing in position hand pump of approved quality for40 mm diameter G.I. pipe complete with all accessories.

18.6 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. 18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11) metre

7208 UPVC bend 87.5° 75 mm bend

7209 UPVC bend 87.5° 110 mm bend

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.2 Kitchen sink without drain board 17.10.2.2 610x460 mm bowl depth 200 mm

18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face withconcealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 18.9.1 15 mm nominal dia Pipes

18.9.2 20 mm nominal dia Pipes

18.9.3 25 mm nominal dia Pipes

18.9.4 32 mm nominal dia Pipes

1/3 Wiring for light -point / fan point /exhaust fan point/call bell point with 2x1.5 sq. mm. FRLS P.V.C. insulated copper conductor single core cable in surface /recessed steel conduit,with modular switch,modular plate,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required. 1.3.3 Group C

1.2.4 Supplying and fixing following modular switch /socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 1.24.1 5/6 A switch

1.24.4 3 pin 5/6A Socket outlet

1.24.3 15/16A switch

1.24.5 6 pin 15/16A socket outlet

1.14 Wiiring for circuit/submain wiring alongwith earth wire with following sizes of FRLS PVC insulated copper conductor ,single core cable in surface/recessed medium class PVC conduit as required. 1.14.2 2x2.5 sq.mm + 1x2.5 sq.mm earth wire

1.14.3 2x4 sq.mm + 1x4 sq.mm earth wire

4 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

2.1 Supplying & fixing 5 Amps to 32 Amps rating 240/415 V "C" Curve miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB Complete with connections testing & commissioning etc as required. 2.101 Single Pole

2.3 Supplying and fixing following way ,single pole and neutral sheet steel ,MCB distribution board ,240V on surface/recess complete with thinned copper bus-bar ,neutral bus-bar,earty bar,din-bar,interconnections ,powder painted including earthing etc as required (But without MCB/RCCB/Isolator) 2.3.2 8-way , double door

12.12 Supplying and fixing following rating double pole ,240V,MCB in the existing MCB DB complete with connections ,testing and commissioning etc.as required 2.12.2 63A

5.2 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories,and providing masonry cover plate having locking arrangement and with charcoal/coke and salt as required.

5.7 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground levelfor conductor earth electrode,including connection/ltermination with GI thimble etc.as required.

A-41 Supplying testing of 4 ft LED Tube light batten including all accessories as directed by he department (Philips make)

A-1 Supplying of following size of PVC/XLPE insulated and PVC sheathed1.1KV grade Solid aluminum conductor up to 10.sq.mm balance strnded conductor ,XLPE insulated ,cores laid up ,PVC tap innersheathed ,Armour (Aluminium wire for single core up to 70 sq.mm balance luminium strip ,Galvanised wire for cables up to 2x10 sq.mm ,3x10 sq.mm 4x6 sq.mm and balance all galvanised steel strip) extruded PVC type ST2 sheathed 650/1100V grade as per IS 7908 (part-1) 1988 armoured U.G Cable as specified and direced by the department(Plaza or equivalent make as approved by this department) 16 sq.mm 3 core

A-2 Supply,Testing,Commissining of 200mm sweep Ventilating fan,Exhaust fan complete as requird. Prduct ID 5116877-8122534914

A-3 Amount to be paid to APDCL for electronic energymeter/service connection charge

A-4 Load Security to be paid to APDCL

(PLANTATION) 2.14 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) 2.14.3 Holes 60 cm dia, and 60 cm deep

(PLANTATION) 2.15 Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: 2.15.1 15With common burnt clay F.P.S. (non modular) bricks of classdesignation 5.0

(PLANTATION) 7.5 Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cmin big polybag of size 25 cm as per direction of the officer-in-charge.

BIR BAHADUR PRADHAN