SPECIAL REPAIR TO GOVT MD ACCN BLOCK NO P 129 08 QTRs AT BAIRAGARH UNDER GE BHOPAL

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Demolition to cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat), removing serviceable tiles and rubbish off the permises complete all as specified and directed.

M&L for 25mm thick, PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in bedding layer for laying and fixing floor, levelling course etc. complete all as specifed and directed.

M&L for double charged vitrified tile light shade 8 to10 mm thick (Square /rectangular ) polished, area of each tile exceeding 0.42 sqm but n.exc 1.00 sqm as on floor with epoxy filling in joints over and including 15mm thick rendering in CM 1:6 set & jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified & directed.

M&L for double charged vitrified tile 8 to 10 mm thick (Square /rectangular ) polished, area of each tile exceeding 0.42 sqm but n.exc 1.00 sqm on vertical surfaces with epoxy filling in joints for skirting dado and risers to steps etc over and including 10mm thick rendering in CM 1:4 set and jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified & directed.

M&L for coloured, non skid, ceramic tiles 7 to 8mm thick (square/rectangular) are of each tile exc 0.11 sqm but n.exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick rendering in CM 1:6 set & jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified & directed.

M&L for glazed bath concept tiles, coloured ( 300 x 450 mm)x 7 mm thick as in skirting/dado over & including 10 mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as spfd & directed.

M&L for heavy duty 10 mm thick, flooring tiles , harsh weather & UV resistance, high abrasion resistance, MOH hardness >6 thickness, area of each tile not less than 0.09 sqm , anti slip type laid in floors, steps, edges etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling, sub base and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping and similar articles complete all as specfified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar complete all as specified and directed.

M&L for granite (of any type) work 15-18mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incluing grinding and polishing over laided 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for kota stone slab 20-25 mm thick in riser of steps skirting, dado and pillar laid over cement screed and jointed over and including 15mm thick screed bed in CM 1:6 etc set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

M&L for 75 mm thick, PCC 1:3:6 type C2 using 40 mm graded stone aggregate in plinth protection, aprons including finishing the surfaces even and smooth without using extra cement complete all as specified and directed

Demolition to brick work built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and directed.

M&L for brick work with sub class ‘B’ bricks (modular size bricks) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks (modular size bricks) straight or curved on plan any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water in cement or cement lime plaster any description all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick or concrete surface in CM 1: 6 finishing the surfaces fair & even without using extra cement complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:3 on fair face of brick/ concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick, ready mix plaster with using WPC on fair faces of brick work finished even and smooth without using extra cement complete all as specified and as directed.

Supply only water prooofing compound all as specified and directed.

M&L for preparation of newly plastered surfaces and applying two coats of acrylic distemper , white or tinted over a coat of putty as approved complete all as specified and directed. Note : Putty will be measured and paid separately.

M&L for complete removal of exiting treatment on wall surfaces and applying two coats of acrylic distemper, white or tinted over a one coat of putty complete all as specified and directed. Note : Putty will be measured and paid separately.

M&L for applying two coats of Dr Fixit Rain Coat Neo (Prime less high build water based elastomeric exterior wall water proof acrylic coating for exterior surfaces) designed with weather resistant acrylate polymers, UV resistant and good hiding and spreading, developing a strong inter coat adhesion with substrate and features such as waterproofing, UV protection, anti-algae resistance, crack bridging of elastic films covering hair line cracks, long term protection, colour variants, preparation of surface by cleaning the surfaces till it is free from dust, grease and flaking paint, any unstable paint to be removed, using high pressure wash or scraper, whichever is appropriate complete all as specified and as directed. Note : 1. Application for vertical surface fresh plaster. 2. Use Dr Fixit Raincoat Neo directly from the container. Stir contents well before use. 3. Brush/Roller apply a self-priming coat of Dr fixit and Neo on the vertical wall surface in SSD condition, diluting 1 ltr with 100ML clean potable water. Allow it to dry for 4 to 6hrs. 4. Apply a coat of Dr fixit Raincoat Neo without dilution as waterproof top coat, either by roller or brush with force coverage at the rate of3.7 – 4.1 sqm/litre to achieve DFT of 100-110 microns. Allow it to dry for 4- 6 hrs. Lighter shades base on the top of dark colours need additional coat of finishing. 5. An addition coat should be applied in case of horizontal surfaces like top of windows, ledges, parapet wall etc. Allow the coating to full air cure for 7 days.

M&L for preparation of newly plastered or previously untreated wall surfaces and applying two coats of white wash complete all as specified and directed.

M&L for complete removal of exiting treatment on wall surfaces and applying two coats of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of newly plastered or previously untreated ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M&L for water proofing cement base putty @ 1kg (undiluted) per sqm of average thickness 1.5mm over plastered surface including preparation of surface completed all as specified and as directed.

M&L for applying of white wall care putty 1 mm thick on walls complete all as specifed and directed.

M&L for complete removal of exiting treatment on ceiling and applying two coats of white wash complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames)exc 1.5 sqm not exc 4.0 Sqm each all as specified and directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet, reinforced with MS square tube, fixing complete as per specification and drawing all as specified and directed.

S&F factory made solid panel, PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F for factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extrapayment on this account shall be made.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules ofelasticity 900 N/mm2 and resistance tospread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall beacceptable. Variation in profile dimensionson plus side shall be acceptable but no extrapayment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain, flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F providing factory made 30mm thick 100% Solid WPC ( Wood polymer Composite ) laminated wiremesh door shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from extrusion process WPC foam sheet single extruded ( Inner ) with having minimum density not less than 650 kg/cum manufactured by "RAJSHRI" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ borer free, Water/ moisture proof and fire retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter. XTN Aluminum Mosquito mesh is inclusive and combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed scresws at required distance, scres and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company complete all as specified and as directed.

S&F for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F of mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc; complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, steel of Fe 410-W (Gde E-250) quality complete all as specified and directed.

M&L in repairs 18mm plywood, grade BWR, type BB with 0.9mm decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions fixed with screws to timber frame work including dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed. Note : Stainless steel butt hines, screws etc will be including in items.

S&F for continuous (piano) hinges, 30mm flaps mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including letting in and fixed complete all as specified and directed

S&F for 125mm aluminum handles, fabricated type, poished fixed complete all as specified and directed.

S&F for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperure 1.40 mm and fixed and with stainless steel wire staples fixed complete all as specified and directed.

S&F 4 mm thick, sheet glass, ordinary quality and glazing with ol putty in square not exc 0.5 sqm in each complete all as specified and directed.

S&F 4 mm thick, figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in pane complete all as specified and directed.

S&F 125 mm long, extruded aluminium alloy, handles complete all as specified and directed

S&F mild steel, cold rolled, medium weight, 100 mm butt hinges fixed to iron frame or welded to iron frame complete all as specified and directed.

S&F 200 mm long, aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 250 mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed

S&F 150 mm long, aluminium alloy, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size, extuded aluminium, alloy handles anodised of complete all as specified and directed.

Demolition and breaking up of any dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap plain with SS grating, fixed and jointed with solvent cement complete all as specified and direcetd.

S&F of 75 mm bore PVC (SWR) bends of any radius and jointed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends of any radius and jointed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) vent cowl and fixed complete all as specified and directed.

S&F 100mm dia grating doom of PTMT(Minimum weight 25 gms) complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F 15 mm GI tube, medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Refixing old 15 mm steel tubing and connection in new or old position(walls, ceiling, floors etc) complete all as specified and directed.

S&F 20 mm GI tube, medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Refixing old 20 mm steel tubing and connection in new or old position(walls, ceiling, floors etc) complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferulle and fixed complete as specified and directed.

S&F in repairs 15 mm bore stop cock, cast copper alloy, chromium plated with long shank and cut (concealed type), screwed down, screwed for iron pipe or union and fixed in repair complete as specified and directed.

S&F in repairs 15 mm stop valves/angle valve, cast copper alloy chromium plated , screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed

S&F in repairs brass, chromium plated shower rose 125 mm in size with or without swivel joints any size incl fixing to steel pipe or union, complete all as specified & directed

S&F vitreous china squatting pan "Orissa" pattern size 580x440 mm white, with integral foot rest (exculding flushing cistern and flush pipe) fixed in repair including cement concrete bedding complete all as specified and directed.

S&F for tubular towel rail chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F of 20 mm dia stainless steel drapery/ curtain rod, min 2 mm thickness with fancy type brackets/holders for hanging and fixing complete all as specified and directed.

S&F in repairs syphonic action type PVC low level flushing cistern 10 ltrs capacity with 32mm dia flush pipe and fixing to supply pipe with brass heads & washers and fixed complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F sinks with drainage board made of stainless steel, 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550 x 400 including brackets and PVC waste pipe etc complete all as specified and directed.

S&F 15 mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and directed.

S&F in repairs CP towel ring round with round flange complete all as specified and directed.

S&F in repairs stainless steel plate rack complete assembeled set of size 31 x 36 x 10 inch fixed with screws all as specified and directed.

Demolition and breaking up of 150 mm dia of drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L for laying DWCP 150mm dia pipes in trenches class SN-8 conforming to IS 16098 (Part-2) in 6 mtr length with coupler complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2 uisng 40 mm graded stone aggregate, concrete bed to drain pipes 150 mm dia including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc; and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for mild steel framed work such as in grills, gratings, railings, frame work of water tanks etc; with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in roof covering / cladding to wall, chajjas, etc. and fixed with self tapping screws complete all as specified and directed

Dismantling fencing wire mesh , any type and any size complete all as specified and directed.

Supply and fix chain link MS galvanised fencing PVC coated, any mesh, size and any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M&L for mild steel, round bars conforming to Gde I (IS: 432 part-I) 8 to 10mm dia in bands, straps, clamps, hooks (pins) fixed in pillars of gate/fencing post for holding barbed wire fencing, chain link fence, etc cut to length, bent to shape required complete all as specified and directed

Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete, masonry, brick work, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

S&F for mild steel works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc and flat iron fillets for securing wire mesh similar work Confirming to Fe-290 Gde E-165 etc complete all as specified and directed.

S&F mild steel, screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts, exc 5cm and n.exc 10cm complete all as specified and directed.

Excavating in post holes in any type of soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, incl removing of surplus soil complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats synthetic enamal paint over one coat of red oxide primer complete all as specified and directed.

Taking down existing old roof treatment of any description , any type including removal old tar felt, screed, etc complete all as direcetd.

M&L for water proofing treatment on roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/Sqm and thickness not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete a as specified. All as per following specifications:

(a) 10 mm thick plaster in CM 1:4 mixed with including water profofing compound @3% by weight of cement applied over roof slab. After the plaster is cured the roof will be tested for water tightening by ponding with water for seven days for any seepage / leakages etc. if any seepage is oberved the rectification will be carried out by pressure grouting under the pressure of 5 Kg/Sqcm using cement based cement grout. After the surface is repired the slab will be tested for watertightness aginst before processing further treatments.

(b) The surface of the roof, parapet and gutters, drain mouths etc. over which water profing treatment is to be applied shall be cleaned of all foreign matters such as fungus, mass, dust etc. by wire brushing and dusting. For cast iron drain outlets the grove shall be cut around to tuck in the treatment as pipes, chimneystacs etc. and other similar situations to ease up about corners.

(c) Bituminous primer VG-10 hot blown bitumen @ 0.30 Kg/Sqm to be applied an prepared surface till the surface is properly impregnated.

(d) APP modified water proofing membrene as specified shall be laid on the primer surface by torch application method as per manufacturers instructions, The overlaps while torching shall be 100 mm in both directions(longititudinal and transverse directions). All overlap joints shall be sealed throughly by thermofusing both the membrene layers and sealing it with the help of hot trowel. The overlap joints shall be made as monolithic layer.

(e) All joints & changes in direction should be curved with cement motor 1:3 mixed with SBR latex @ 200 ml per beg of cement and cured well before laying the membrane.

(f) A fillet of PCC (1:2:4) type B-o of 100 mm x 100 mm shall be provided at all junctions of vertical and horizontal surfaces and whereever ther is a change of direction. The membrane should not be taken over at any steep turns and hence all corners /junctions should be rounded.

M&L for 9 to 10mm thick, 600x600mm size, ceramic roof cool tiles, white, confirms to sun reflective index (SRI) value minimum of 90, over and including 15mm thick rendering in CM 1:4 set & jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified & directed.

S&F for rotational moulded polyethylene water storage tanks 500ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm dia PTMT float valve and dismantling of exisinting tank complete all as specified in SSR Part I complete all as specified & directed.

S&F for rotational moulded polyethylene water storage tanks 1000ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm dia PTMT float valve and dismantling of exisinting tank complete all as specified in SSR Part I complete all as specified & directed.

S&F in repairs 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm- 690 gms)

S&F 20mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified & directed.

S&F 25mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified & directed.

M&L for repairs of damaged RCC columns, beams etc including chipping of loose concrete, cleaning of exposed reinforced, fixing of GI wire mesh using binding wires/nails, and recasting in cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate and finished the concrete surface with 10mm thick rendering in CM 1:3. complete all as specified and as directed. Note :- (a) Rates are deemed to be included with necessary formwork. (b) GI netting and wire will be measured and paid separately under supply only item.

Supply only GI wire netting made of 0.9mm dia galvanised iron wire with 12mm x12mm square mesh complete all as specified and as directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Use & waste Formwork to chajjas,troughs and similar items including edges rough finished complete all as specified and as directed.

Use & waste Formwork to fins, louvers, fascia with rough finished surfaces complete all as specified and as directed.

Use & waste Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10 cm wide complete all as specified and as directed.

M&L for reinforced cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) in Chajjas, floor etc complete all as specified and as directed.

M&L for reinforced cement concrete type B1 1:2:4 (using 20 mm graded stone aggregate) in fins, fascias, louvres, parapets,and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and as directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with multi-stranded copper conductor stranded copper conductor 1.5 Sqmm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, (IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with metal ms flush box, white cover plate with frame for fixing modular switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:-

All as per item No. 117 .00here -in- before but wiring with 4.0 Sqmm FRLS mutistranded copper conductor cable for 5/15 amp switch socket combination on independent board and with 4.0 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

All as per item No 117.00 here-in-before, one 3 pin socket outlet 5 Amps on same board all as specified and directed.

All as per item No 117.00 here-in-before, but 3 pin socket outlet 5 amps on independent board elect wiring 1.5 sq mm complete all as specified and directed.

S&F for modular Switch piano, flush type, single pole, one way, 6/16 Amps, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed.

S&F in repairs ceiling rose surface bakelite, three terminals, 240V, 50Hz, ISI marked complete all as specified and as directed.

S&F modular socket outlet, 2 module, multipurpose having provision for 2 & 3 pin, 6/16 Amp flush type, 240 volt AC complete all as specified and as directed.

Supply and fixing BEE, 5 stare rated, BIS certified BLDC decorative ceiling fan 1200mm sweep, 230Volt, minimum dia delivery 225 CFM, anti dust, aerodynamic aluminium blades & body with advanced brushless technology bosed BLDC, copper winding motor with all accessories such as regulator, conneting down rod, clamps, canopy, remote with boost, timer & sleep mode including taking down old fan complete all as specidied and directed by Engineer-in-Charge. Note:-(i) Cost of taking down old ceiling fan, regulator & deposit to MES Store yard in also include in quoted rate. (ii) Warranty of BLDC ceiling fan for 2 year & 5 Year of BLDC Motor.

Supply and fixing energy saving LED street light fitting 35 Watt 230 V, AC outdoor type with high pressure die cast aluminum housing toughened glass thermal shock and impact resistance and heat resistant complete with powered by integrad electronice driver with out put short circuit protection, surge protection, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete toughened glass, lens IP 66, IK-08 and with system efficacy of 125 lm/W CRI >70 , PF≥0.95 complete all as specified and directed by Engr-in-Charge.

S&F LED 20/21Watt tube light fitting (T8 type), including LED retrofit tube 20/21 W one side connection type, 240 v, PF > 0.90, colour temp 6500 K, system luminious efficacy > 100Lm/W, complete with powder coated CRCA decorative patti suitable for surface mounting on wall, complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 12 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed by Engr-in-charge.

S & F in repairs MCB SPN suitable for 240 volts, AC supply 32 Amps, C Curve, ISI marked with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

S&F MCB, SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' Curve ISI marked including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-In-Charge.

Taking down and servicing/greasing/painting of ceiling fan of size 1200mm sweep and refixing in position including provision 3 core flexible PVC insulated multi stranded copper conductor of size 0.5 sq mm from ceiling rose/ connector to fan with replacement of capacitor complete all as specified and directed.

M&L for sub main wiring with two single core FRLS, PVC insulated unsheathed cable 1100 volts grade, 4.0 sqmm size as per ISI marked with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI marked including PVC insulated unsheathed 4 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers complete all as specified and directed by Engr-In-Charge Note :- Old/unserviceable exhaust fans to be deposited at MES Store yard and taken into lesser book.

S&F in sheet metal plug & socket, single pole and neutral ISI marked with and including 1 No single pole MCB 20 Amps 240V complete all as specified and directed

Supply and fixing 240V, SP, 25 ltrs capacity, BEE, 5 star rated geyser with advaced safety features making all necessary arrangements for connection to cold and hot water pipe lines and testing of storage water heater, 240V, SP, 25 ltrs capacity including PVC hot and cold water pipe connections . NOTE: New geyser has been taken for building with no provision of geysers.

S&F 9 Watt, lamp holder (Angle holder) PVC/polycarbonate type cased body with back plate suitable for pendent fittings including LED bulb complete all as specified and directed.

Supply and fixing factory made epoxy powder coated distribution board TP & N 4 ways ( VTPN MCCB DB ) and space for MCCB as incomer, with metal door ( IP-43 protection ) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated Neutral Bar, Insulated busbar assembly, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts complete all as specified and directed.

S & F in repairs MCB TPN suitable for 240 volts, AC supply 40 A to 100 Amps, C Curve, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed.

Excavation in trenches nexc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose for laying cables, erection of poles complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated soil nexc 50 mtr and depositing where directed at a level n-exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning/sand covering for underground cable protection complete all as specified.

Supplying and laying Class LV, Type I, flat, size 250mm x 150mm x 40mmfor cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Takng down old unservicable cable and Supply and Laying XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16x4 sqmm, laid in trenches/floor or fixed on wall/pole complete all as specified and directed.

S&F for 25 mm bore GI Tubes, 'light grade' galvanised, with all fitting and laid in floors, under road, pavement or hard standing complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron earth wire of 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR including earth pit in any soil char coal common salt , 15 mm all around earth plate PCC (1:3:6) type C1 using 20mm graded stone aggreagte type culprit, with 40 x40x6 mm angle iron frame and PCC cover (1:2:4) type B1 , water pipe funnel and GI protection pipe light grade 15mm dia upto panel connecting earth lead to panel all as specified and directed by EIC. Note : Earth continuity conductor including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate.

Taking up or down 25 mm bore steel tubing and connection including cleaning for refixing or removal in store all as specified and directed.

Supply , fixing & laying in repairs GI tubing 25mm bore, medium grade with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor/ all as specified and directed of following size Make :

Deduct Schedule of credit (calculation will be done off line) Rs.55465.00