GE(W)/HSR-16/2021-22 SPECIAL REPAIR TO TOILET OF BLDG NO P-143 OF 11 MECH INF AT HISAR MIL STN UNDER GE (WEST) HISAR

Amount

Demolition of reinforded cement concrete of any description and in any position not otherwise specifically provided for beams, column, slab, chajjas and similar work including removing rubbish complete all as specified and directed.

Demolition of cement concrete as in ground floors and pavings not exceeding 15 cm thick below or above ground level (unreinforced) incluiding removing rubbish complete all as specified and directed.

Taking up or down steel water tubing and connections including for re-fixing or removal from site 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel water tubing and connections including for re-fixing or removal from site 20 mm bore of pipe complete all as specified and directed.

M&L for steel water tubing (medium grade) galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 15 mm bore of pipe complete all as specified and directed.

M&L for steel water tubing (medium grade) galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 20mm bore of pipe complete all as specified and directed.

M&L for steel water tubing (medium grade) galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 25mm bore of pipe complete all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. and directed.

S&F brass threaded elbow suitable 20mm outer dia CPVC pipes complete all as specified. and directed.

S&F brass threaded Tee suitable 20mm outer dia CPVC pipes complete all as specified. and directed.

S&F brass threaded Male / female Adaptor (MTA/ MBTA) ) suitable 20mm outer dia CPVC pipes complete all as specified. and directed.

Dismantling old u/s PVC water tanks exc 500 & n exc 1000 ltrs capacity complete all as specified and directed..

S&F 1000 ltr capacity rotional molded polythylene water storage tank three layer white triple layer (Cylinderical vertical with closed top , white in colour ) hoisted kand fixed in position including ball valve 20mm bore high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed, (minimum weight 210 gms)complete all as specified and directed.

M&L for cement concrete 1:5:10 type E2 ( using 40mm graded stone aggregate ) filling in sunken and mass concrete complete all as specified and directed.

Taking down chowkats or frame without taking off shutters (with or without glazing and ventilator) not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frame with shutter, without taking off shutter from the frames area exc 1.5 sqm but not exc 4sqm each complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches pillars etc and removing rubbish complete all as specified and directed.

M&L for brick work with fly ash Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:4 in half brick thick complete all as specified and directed.

M&L for MS TMT bar 10mm dia or over cut to length bent to shape reqd incl cranking bending etc complete & binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars upto 8mm dia and over cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire 0.9 mm dia. complete all as specified and directed.

All as per item No 21 above but for 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders.6 to 8mm dia.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick flat rough finished surface complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.rough finished surface complete all as specified and directed.

M&L for Formwork toFormwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surface complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished surface complete all as specified and directed.

M&L RCC M-25 (Design mix) 20mm graded aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 (Design mix) 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC M-25 (Design mix) 20mm graded stone aggregate as in Chajjas complete all as specified and directed.

M&L for RCC M-25 (Design mix) 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like. complete all as specified and directed.

M&L for RCC M-25 (Design mix) as in column , pillars, piers, posts and struts complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2 , 1:4:8 ( using 40mm graded stone aggregate ) as in sub base complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:6 over brick / concrete wall surfaces trowelled to even & fair w/o using extra cement for internal wall surfaces complete all as specified and directed.

M&L for 15mm thick plaster in CM 1:4 on brick or concrete wall surface finished even and fair without using extra cement mixed with liquid water proofing admixture as per manufacturer's instructions complete all as specified and directed. Note :- WPC will be paid separately.

M&L for 10mm thick rendering in CM 1:3 over brick / concrete ceiling surfaces trowelled to even & fair w/o using extra cement for internal wall surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement base paint of any tint over one coat of primer complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coats of OBD over one coat of 1mm thick wall care putty on wall complete all as specified and directed

M&L for preparation newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for 50mm thick, cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed. .

M&L for coloured Non skid ceramic tiles 7 to 8mm thick , area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry pointed in coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed..

M&L for coloured designed glazed ceramic tiles in vertical surface of size 350x250x7mm /450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

S&F in repairs 15mm bore angle valve, CP cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed.

S&F in repairs 15mm bore concealed type stop valve, CP fancy type cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed.

S&F in repairs 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed.

S&F in repairs 15mm bore bib tap, brass chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints including Stainless steel arm fixed to steel pipe or union complete all as specified and directed.

S&F in repair vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specified and directed.

S&F in repair of PVC valveless syphonic type 10Ltr capacity flushing cistern with inlet , ball valve and handle including flush pipe of pvc 32mm dia complete all as specified and directed

S&F in repair vitreous china wash basin white flat back size 550 x 400mm size, incl cutting for and pinning in ends of brackets, waste fittings, PVC waste pipe and 15mm pillar tap cast copper alloy with capstan head chromium plated complete all as specified and directed

S&F in repair towel rail 600mm long PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190 gms) complete all as specified and directed.

S&F in repair 75mm outer dia PVC (SWR) multi floor trap with grating including jointing with solvent cement ®complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F mild steel butt hinges of size 100mm medium weight, cold rolled complete all as specified and directed.

S&F stainless steel butt hinges of size 100mm medium weight, cold rolled complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 200mm long complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section 150mm long complete all as specified and as directed.

S&F Aluminum alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F 150 mm extruded Aluminium handles, cast type,anodised complete all as specified and directed.

S&F 200mm long mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipe single socketed with rubber joint, jointed with solvent cement / chemical and tested laid in trenches l complete complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipe single socketed with rubber joint, jointed with solvent cement / chemical and tested laid in trenches complete complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipe single socketed with rubber joint, jointed with solvent cement / chemical and tested fixed to wall with mild steel clamps of suitable size complete complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F, 110mm dia PVC (SWR) bend any radius complete all as specified and directed.

S&F, 75mm dia PVC (SWR) bend any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) single junction (single 'T) equal or unequal provided with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F Factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reiforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

M&L for preparation of new untreated steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new untreated steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over existing coat of primer complete all as specified and directed.

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bars; door chowkats / frames including cutting to required length, ladders; framed balusters; walk ways; railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' of size 150x150mm complete all as specified and directed.

S&F for 32mm dia of pipe waste fittings, brass, chromium plated for sinks, basins, etc. with long screwed shanks and fly-nuts, flange complete all as specified and directed.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified and directed.

S&F Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic leats (Minimum weight 105gms) complete all as specified and directed.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including mild steel butt hinges, tower bolts, handles etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including taking down old existing window and making good disturbed surfaces of walls,complete all as specified and directed. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Details of box type window shall be given on HQ CEJZ drawing No TD/2013/01 sheet 1/3, 2/3, 3/3. (iii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including mild steel butt hinges, tower bolts, handles etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including taking down old existing window and making good disturbed surfaces of walls, complete all as specified and directed. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Details of box type window shall be given on HQ CEJZ drawing No TD/2013/01 sheet 1/3, 2/3, 3/3. (iii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made box type Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F pressed steel frames 125x60mm for doors with one or more rebates made out of 1.25mm thick PBI sheet including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as ifilling of chowkhats complete all as specified and directed. .

S&F 35mm thick 2nd class HW rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick glazed and skelton shutters open rebated and prepared to receive gauze etc (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred breds for securing glass etc sizes of members of shutters as specified in SSR Pt-I Sec 8 Clause 8.20(a) in 2nd class hard wood complete all as specified and directed.

S&F 3 mm sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each pane complete all as specified and directed.

S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for preparation of new wood or wooden based material surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed

M&L for 20 to 25mm thick machine cut Kota stone (550 x 550 mm) flooring over cement screed base laid and jointed with grey cement slurrry mixed with pigments to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

All as per item No 91.00 but kota stone slab (100/150mm x 550mm) and 20-25mm thick in riser of steps, skirting , dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm dia pipe complete all as specified and directed.

M&L for Salt-glazed stoneware drain pipes laid in trenches and jointed as specified for 150mm internal dia of pipe complete all as specified and directed.

Dismantling brick tiles or terracing tiles single layers as on roof and removing complete all as specified and directed .

Demolition of mud phuska on roof of any thickness including plastering and leeping whether full thickness removed or only a part there of removing debris to a distance exc 1 km but not exc 1.5 Km all as specified and directed.

M&L for applying roof treatment on top of roof with APP based polymeric membrane (not less than 3mm thick , weight not less than 3.5Kg per Sqm, reinforced with polyster non-woven fabric ( weigthing not less than 150 gm/ Sqm ) laid by torch application method with side overlap 75mm and on end 100mm as per manufacture's instructions over a coat of hot paving bitumen of grade 30/40 conforming to IS 73 @ 1.2 Kg/ Sqm over a coat of bituminous primer conforming to IS -1984 @ 0.40 Kg /Sqm and applying two coats of aluminium paint over APP membrane over and incl 15mm thick plaster in cm 1:4 using liquid WPC as per manufacture instruction over RCC roof complete all as specified and directed

M&L for Cement concrete chequred tiles 25cm x 25cm x 25mm thick, machine pressed; with grey cement and no pigment set jointed and pointed in neat cement slurry in floors, and cut and polished over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for providing precast cement concrete type B-I 1:2:4 (using 20mm graded stone aggregates) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs,mangers, shelves and similar articles with plain face set in cement mortar 1:4 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Taking down cement plaster incl racking out joints, hacking for key & scrubbing down with water etc including removing rubbish complete all as specified and directed.

Chipping of loose/ damaged / cracked / previously repaired/ delaminated or weak concrete by chieseling to expose the sound core concrete where ever required and to expose rusted reinforcement upto depth n.exc 50mm and disposal of rubbish off the premises to a distance not exc 50 mtrs including cleaning of reinforced concrete surface by air compressor complete all as specified and directed.

Supply and apply of rust remover cum passivator to remove rust from existing reinforcement by using Product : Rustoff-100 of Sika or equivalent make in Fosroc / Thermax as approved by GE, with density : 1.01 Kg/ltr at 30°C and consumption : 0.2 kg/Sqm/coat complete all as specified and directed. Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar complete all as specified and directed.

M&L for cement based polymer modified rebar corrosion protection system to existing reinforcement using cement based polymer modified rebar corrosion protection system with consumption : 3.75 kg/Sqm for two coats and product requirements: carbonation resistance : 2 mm of SikaTop Armatec®-108 of Sika or equivalent make in Fosroc / Thermax as approved by GE corresponds to 20 mm of normal mortar; bond strength > 1N/Sqmm according to ASTM C 882-78 complete all as specified and directed. Note : The material to be applied thoroughly on exposed rebars only with the help of a brush of suitable size. The area will be measured as length of bar x two times the dia of bar complete all as specified and directed.

M&L for providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer’s specification including prepartaion of surface throughly and cleaning complete where ever required with using Product : Sikadur®-32 LP of Sika or equivalent in Fosroc /Thermax as approved by GE with consumption : 0.4 kg/Sqm and Product requirements : Comp with ASTM C 881-78, Type II Grade 2 Class B+C complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness exceeding 10mm and upto 25mm to the prepared concrete substrate in soffit of slabs, beam, columns, parapets, fins and facias at any height, including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for providing by mixing and trowel application of prepacked, light weight, two component structural grade polymer modified fibre reinforced thixotropic cement mortar Sika Monotop 122F of Sika or equivalent make in Fosroc / Thermax as approved by GE at an average thickness of upto 10mm to the prepared concrete substrate in soffit of slabs, beam, columns, parapets, fins and facias at any height including finishing of applied Polymer mortar as per the technical specifications and manufacturer's instructionscomplete all as specified and directed.

M&L for providing, fixing shear connector of 10 mm dia TOR steel upto 160 mm length with Sika anchorfix @ -2+ Tropical or equivalent make in Fosroc / Thermax as approved by GE, epoxy resin to RCC member including power drilling, cleaning of holes, insertion of epoxy, placing shear connector in position to ensure the bond as per manufacturer’s instructions complete all as specified and directed.

M&L for cutting V groove (15mmx10mm) along the crack line and cleaning the same with high pressure water jet and sealing with fast setting high strength Epoxy putty, solvent free, three component compound based on epoxy resins, graded fillers and thixotropic agents using Sikadur 31 of Sika or equivalent make in Fosroc / Thermax as approved by GE as per the technical specifications and manufacturer's instructions complete all asspecified and directed.

M&L for applying a ready to use non shrink, cementitious free flow microconcrete (<100 mm) using Product : SikaRep® Microcrete-4 + adequate coarse aggregate, Yield: approx. 17 ltr/bag (30kg) (depending on the size and quantity of coarse aggregate added), Product : SikaRep® Microcrete-4 or equivalent make in Fosroc / Thermax as approved by GE, Product requirements: compressive strength > 60 N/Sqmm (28 days) according to ASTM C 1107-99 complete all as specified and directed.

M&L for providing and application of one coat of Water based concrete curing compound with low viscosity wax emulsion using Sika Antisol E - WP of Sika or equivalent make in Fosroc / Thermax as approved by GE, as concrete curing membrane over the applied polymer mortar as temporary curing membrane as per the technical specifications and manufacturer's instructions complete all as specified and directed.

Providing and erecting hydraulic & manual steel props upto full height, braced at centre, resting on wedge and block to support the structure provisionally during repair work and maintaining them in position till required and as directed. Note : Hydraulic & manual steel props will be provided, erected and maintain the interval distance of steel props c/c at site on the basis of site reqmt complete all as specified and directed.

M&L for weld-mesh of size 75x75x3mm to be wrapped on the exposed surface of rib of beam & on the slab bottom and tack welding to the exposed reinforcement at close intervals and gunite with cement mortar 1:3 mixed with admixture SIKA Plasto creat plus or equivalent make in Fosroc / Thermax as approved by GE around rib of beam or roof slab of thickness n.exc 40mm to be applied under an operating pressure. the gunited surface to be cured properly for a min of 7 days all in complete as per the technical specifications and manufacturer's instructions complete all as specified and directed.

M&L for providing and fixing water tight centering and shuttering including bolting, strutting, propping etc. including removal of form work from column, beam etc. complete as per site requirement complete all as specified and directed.

M&L for treatment of sunken floor slab comprising of the following specifications complete all as specified and directed :-

(i) Cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. Provision of 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding conc to achieve proper slope including cutting holes in bricks or RCC wall for spout.

(ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with and including integral water proofing compound Sika Plastocreat plus or equivalent make in Fosroc / Thermax as approved by GE @ 0.2% by wt of cement consumed including filling it with water to check dampness and seepage and where dampness / seepage is noticed, nozzles shall be fixed and grouting carried out.

(iii)All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy puty Sikagard 694 F (I) or equivalent make in Fosroc / Thermax as approve by GE.

(iv) After drying putty, wash the slab and sides of sunken portion with water andmake it clear and clean.

(v) Applying two coats of polymer modified cementious water proof coating with Sika Topseal 107 or equivalent make in Fosroc / Thermax as approved by GE in two coats @ 3kg/sqm to sandwiched with glass fibre reinforcement : Sika® Fab-1 or equivalent make in Forsro / Thermax as approved by GE over base coat as per manufacturs instruction to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion.

(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound SIKA plastocreat Plus or equivalent make in Fosroc / Thermax as approve by GE @ 0.2% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout.( WPC shall be measured & paid separately)

(vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint (Black Japan shall be paid separetely).

NOTE : Item No 101 to 114.07 shall be executed by authorized applicator of manufacturer as approved by accepting officer)

Taking down carefully copper/aluminum point wiring (light/fan/socket or power) complete including taking out existing unserviceable terminal boxes & conduit with switches/sockets/fan regulators and fittings such as ceiling rose, pendants, tube light fittings, lamp holders, brackets light fittings, rectangular blocks etc. and making good disturbed surface of walls, floors etc. to match with the existing surface etc complete all as specified and directed.

M&L for point wiring for one light / bell / Ceiling fan/Exhaust Fan point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FRLS drawn through rigid PVC coduit 20 mm dia medium grade and conduit accessories concealed type in walls/ceilings and including change of steel terminal sunken boxes and 3 mm thick phenolic laminated sheet top cover for sunken boxes flush to surface for one light point/fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FRLS connected to common earth dolly complete complete all as specified and directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).

All as per item No. 117 above but for one 5 Pin 5 Amp socket outlet on the same board controlled by one number one way switch on same board.

All as per item No. 117 above but for one 5 pin 5 Amp socket outlet on independent board controlled by one number one way switch on independent board.

All as per item No. 117 above but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi strand on independent board including provn of 2.50 Sqmm unsheathed, multi stranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed.

Taking down carefully copper/aluminium Submain wiring from battan /conduit from DBs,MCBs, etc) and making good to disturbed surfaces of walls, floor etc. all as specified and directed

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi stranded conductor FRLS cable of size 4 sqmm, 1100 votls grade drawing through and including PVC casing and caping with acessories and including PVC insulated 4 sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and directed. (Note:- Two lengths of 4 Sqmm cable, one length of 4 Sqmm cable and one length of PVC casing and caping will be measured as one length).

S&F flush type socket outlet multipurpose 3&6 Pin, 15 Amp 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 2&3 Pin, 5/6 Amp 230 volts AC complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230/240 Volts grade complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230/240 Volts grade complete all as specified and directed.

S&F Lamp holder of PVC / Polycarbonate type surface with 9 watt LED bulb complete all as specified and directed.

S&F ceiling rose surface bakelite, 3 terminals with back plate etc complete all as specified and directed.

S&F LED tube light fitting 18W metallic frame /batten, Retro, Box type surface and wall mounted, including LED tube light rod , high efficiency including making connection, complete all as specified and directed.

S&F MCB SPN, 32 to 40 Amps 240 Volts , type 'B' curve, 10 KA, for fixing in DB complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps 240 Volts , type 'B' curve, 10 KA, fixing in DB complete all as specified and directed.

S&F Sheet metal enclosures for DBs when MCBs to be used Single pole and neutral (SPN 240 Volts) with 200 Amps rated busbar 8 way double door complete and all as specified and directed

S&F Exhaust Fan 380 mm sweep, heavy duty 230 volts, fixed on wall with suitable size nut, bolts and washers and connection with and incl 3 core flexible wire 0.5 Sqmm copper flexible cable , incl provn of hole complete all as specified and directed.

SACKSON ENTERPRISES

M/S RAJINDER SINGH